PRT3 : Reference and Installation manual
Contents
1. 2 Arming Disarming Events 3 Alarm and Alarm Restore Events 4 Tamper and Tamper Restore Events 5 Trouble and Trouble Restore Events 6 Special Events 7 Access Events Fire Reset Contact Module Access Remote Access PC Fail To Com User Code Entered Bypass Programmed Delay before Transmitting and Utility Key Pressed Cold Start Warm Start Test Reports WinLoad Login Logout Installer In Out Access Granted Denied Request For Exit Door Left Open Alarm Door Left Open Restore Door Forced Alarm Door Forced Restore spectra 4 Arming Disarming Events 5 Alarm amp Alarm Restore Events 6 Tamper amp Tamper Restore Events 7 Trouble amp Trouble Restore Events 8 Special Eventst see below for Special Events t PG amp FNC1 keys pressed Button Pressed on Remote Bypass Programming User Activated PGM Breaching Zone with Delay and System Power Up Enable Parallel Port EVO Option 1 Spectra Option 4 Printer Status Mask Options EVO Spectra 3 5 Off Line Status Mask 4 6 Paper Empty Status Mask 5 7 Printer Fault Status Mask 6 8 Printer Busy Status Mask If the Printer Status Mask Options are ignored printer troubles will not be displayed These options apply only to the parallel port Setting the Date Spectra After a power failure the date must be reprogrammed Setting the Time Spectra After a power failure the time must be reprogrammed EVO2. Automatic Printing of Zone Status Each section represents 8 zones i e 060 zones 145 152 065 zones 185 192 The Printer Module must be assigned to the same partition as the zone Paradox Memory Key Not To BE USED WITH UL LISTED SYSTEMS The Paradox Memory Key can copy the programmed contents of one PRT3 into as many others as needed For more information see the control panel s programming guide EVO Spectra 090 902 Copy to Memory Key 080 900 Paste to PRT3 When the PRT3 emits a confirmation beep wait for a second confirmation beep and then remove the Memory Key Press the PRINT TEST switch to perform a print test i y EAEEIINT TENEN paradox com Memory Key To Control Panel RED BLK GRN YEL DB 9 Serial Port Pin Out Diagram Pin 5 GND Home Pin 4 DTR Data Terminal Ready Not Used 4 Automation l Module Pin 8 CTS Control Transmission Not Used Pin 3 TX 5 C Bus PC Interface Pin 2 RX Not Used in Event Reporting EVO control panels only 1 See LED Feedback on page 1 2 25 Pin Parallel Port Connect the Printer Module s 25 pin parallel port to any dot matrix printer Note The dot matrix printer must support a minimum of 80 columns 3 9 Pin Serial Port Connect the Printer Module s 9 Pin serial port to a dot matrix printer Note The dot matrix printer must support a minimu
3. Spectra Sections Sections Enable Serial Port Option 1 The Printer Module can use the HyperTerminal communication program that comes installed with Windows Using HyperTerminal the Printer Module will display events as they occur on your computer s monitor 1 Click Start from the Windows taskbar gt Programs Accessories gt Communications gt HyperTerminal The Connection Description window is displayed 2 Enter a name in the Name text box and select an icon for your connection file Click OK The Connect To window is displayed 3 From the Connect Using drop down list select the COM port connected to the Printer Module Click OK The COM Properties window is displayed 4 Click on the Bits per second drop down list and select the baud rate that is set in the Printer Module Section 016 Options 2 amp 3 By default HyperTerminal sets the Data bits at 8 the Parity at None and the Stop bits at 1 Click OK 5 The HyperTerminal display will appear already connected to the Printer Module Click on the Properties icon or select Properties from the File menu The communication file s Properties window is displayed Click the Settings tab Under Emulation verify that it is set as Auto Detect If not select Auto Detect from the drop down list Click OK Baud Settings Option 2 3 Both the Printer Module and serial port should have the OFF OFF 2400 Baud same baud rate Refer to the printer
4. s instruction manual iil jac ampt tes ts OFF ON 19200 Baud for the correct baud rate ON ON 57600 Baud Baud Rate Settings Serial Port Usage Option 4 Set the Printer Module s serial port usage to either Event Reporting off or Home Automation on Note For information on using the Printer Module as an interface for a home automation system refer to the ASCII Protocol Programming Instructions and or C Bus Programming Instructions available on our website at paradox com Automatic Printing of Zone Status Each section represents 8 zones i e 020 zones 97 104 025 zones 137 144 The Printer Module must be assigned to the same partition as the zone Manual Event Group Printing The event groups are represented by the following sections Event Feature Start End Group Group Arming Disarming Events 032 033 Alarm Alarm Restore Events 036 037 Tamper Tamper Restore Events 041 T045 eT T0531 Miscellaneous Events Trouble Trouble Restore Events Special Events 048 Access Events 052 All Events 056 057 Each group of sections from 027 to 058 represents event groups that can be printed when a specified action from the PGM Programming Table occurs see the control panel s programming guide Event Groups 000 to 055 can be used to program the Printer Module s Manual Printing feature Event groups 062 and 063 can only be used when using an EVO control panel
5. its affiliates in Canada the United States and or other countries
6. OM ports to the Printer Module s serial port Events can be displayed and printed using communication software like Procomm Telix and HyperTerminal It is recommended that only dot matrix printers that support a minimum of 80 columns be connected directly to the Printer Module Only dot matrix printers can print individual events in real time LED Feedback Panel Bus ERROR RX TX Combus shorted GND or VCC No clock No data ON Wrong data Invalid combus address Too many modules Reserved for future use ON Combus lines are reversed Clock in Green Data in Yellow FLASH Serial Bus Condition Printer module is receiving information Printer module is sending information Entering EVO Programming 1 Hold 0 key INSTALLER CODE 3 Enter module s 8 digit SERIAL NUMBER 4 Enter SECTION and enter the required DATA 4 Enter the required DATA EVO Spectra Sections Sections Entering Spectra Programming 1 Press the ENTER key 2 Enter section 953 DGP 848 4003 EVO 2 Enter the INSTALLER CODE 3 Enter 3 digit SECTION you wish to program Partition Assignment Digiplex Options 1 to 8 Spectra Options 1 to 2 Automatic Printing of Zone Status Each section represents 8 zones i e 002 zones 1 8 013 zones 89 96 The Printer Module must be assigned to the same partition as the zone Automatic Printing of Event Groups EVO 1 Miscellaneous Events
7. S PECTRA EN O Printer Module V1 2 amam z a E nainn ba jip Hues T ifr P ca E Jei fe a s Se ee ma E E Uae P A R ADO X SECURITY S YS TEM Printed in Canada 09 2009 PARADOX COM PRT3 El02 Introduction The Printer Module PRT3 provides the ability to automatically print live or stored events Sample Printout 2007 06 12 07 17 Partition 1 Arming with master John Doe 2007 06 12 18 09 Partition 1 Disarming with master John Doe Home Automation Interface Capabilities When used with an EVO Series or DGP 848 V4 11 or higher control panel the Printer Module can also be used as an interface between a home automation system and your control panel For information on this feature and its related programming sections refer to the ASCII Protocol Programming Instructions and or C Bus Programming Instructions available on our website at paradox com Technical Specifications Parallel Port Minimum 80 column printer Serial Port 1 start bit 8 data bit no parity and 1 stop bit 8N1 Input Voltage 9 16 Vdc Current Consumption 60mA maximum Serial Port Baud Rates 2400 9600 19200 or 57600 bps Event Buffer 2048 events Compatibility EVO48 EVO96 EVO192 DGP 848 or DGP NE9Q6 control panel Spectra 1728 or 1738 control panel V2 0 or higher PRT3 can be used to replace a PRT 1 Printer Requirements Dot matrix inkjet or laser printers can be connected through one of your computer s C
8. m of 80 columns 4 9 pin Serial Port Connect the Printer Module s 9 pin serial port to a home automation module 5 9 pin Serial Port Connect C Bus to the Printer Module using a null modem cable 6 9 pin Serial Port Connect either the Printer Module s USB or 9 pin serial port to a computer s COM port to view the control panel s events on the computer s monitor The events display on the monitor can then be printed through the printer connected to the computer Remove AC power and battery before adding a module to the system Please refer to the control panel s Reference amp Installation Manual for the maximum allowable installation distance Only one PRT3 can be connected per Spectra control panel Note Printer cable length must not exceed 25ft Warranty For complete warranty information on this product please refer to the Limited Warranty Statement found on the website www paradox com terms Your use of the Paradox product signifies your acceptance of all warranty terms and conditions 2009 Paradox Security Systems Ltd All rights reserved Specifications may change without prior notice One or more of the following US patents may apply 7046142 6215399 6111256 6104319 5920259 5886632 5721542 5287111 5119069 5077549 and RE39406 and other pending patents may apply Canadian and international patents may also apply Spectra Digiplex and EVO are trademarks or registered trademarks of Paradox Security Systems Ltd or
Download Pdf Manuals
Related Search