INSTALLATION MANUAL
Contents
1. Il THE PREMIER DS 2004 2002 amp 2001 run Eun EXCELLENCE IN CUSTOMER OF THE YEAR CARE amp SERVICE 2000 BEST MANUFACTURER 2000 amp 1999 THANK YOU FOR VOTING TEXECOM INSTALLATION MANUAL Com GSM GSM Communicator Module Issue 1 ce Texecom wWww texe com ComGSM Module Installation Manual Introduction The ComGSM module be connected to the Premier 24 48 88 168 640 control panels to provide the following facilities e Report system events alarms arm disarm etc via text messaging to mobile telephones e Remotely arm disarm and obtain current status of the alarm system via text messaging e High speed modem communication for upload download The GSM module can only be used as a modem if the data service is NOTE provide this feature ComGSM Layout 0 st gt 7 2 6 2 o EE 18283 o 5 ESL ILIA 7 e W 8 9 4 o J TEIL NUE TT PCG0123456 D O o 0 C tium enabled by your network provider Pay as you go tariffs generally do not INS315 ComGSM Module Installatio2. op on outputs s 5678 op on 2 turn PC output 2 on Turn Outputs Off op off outputs 5 leucir Pe output Send Message m RU You Displays How Are 5678 status System Status 22272 status System Disarmed or Armed PC Output 1 ON PC Output 2 ON INS315 5 ComGSM Module Installation Manual Premier 48 88 168 640 SMS Control Commands operation Command Ham Arm System 2299 arm areas s Fas arm s arm all areas and report back Part Arm System parm 1 2 3 5 5678 parm 1 part arm 1 all areas no status 2 darm areas s cn abcs disarm areas abc and report Reset System 5678 reset reset all areas Omit Zone s 5678 omit 1 5 12 omit zones 1 5 and 12 2777 Unomit Zone s 5678 uomit 12 reinstate zone 12 22 Turn Outputs outputs s 5678 op 134 turn PC outputs 1 4 on Turn Outputs Off 227 op outputs s 5678 op off 48 turn output 4 off and report Band Massage ne You Displays How 5678 status Armed 1 8 or A P Alarm 1 8 or A P System Status 222 status Output 1 8 Mains OK or Fault Battery OK or Fault Phone Line OK or Fault 5678 status Armed 1 8 or A P Alarm A P Channels 1 8 Output Status 222 status Digi 1 8 Panel 1 5 Mains OK or Fault
3. Battery OK or Fault Phone Line OK or Fault 5678 status R Serial only if Radio Pad fitted NUA only if Radio Pad fitted FSS only if Radio Pad fitted GSM Radio Pad 5599 status R RSS only if Radio Pad fitted Status BER only if Radio Pad fitted CRC only if Radio Pad fitted GSM Signal GSM BER 6 INS315 ComGSM Module Installation Manual What will be sent in the Text Message The following information will be received in the text message My Home Nameprogrammedintophone 3 WesternRoad Upto16characters oftext thisisthe Printer Header 12 45 58 01 12 Timeand Date Zone 003 EventType The Detectorin the Lounge Zone Usernametext Areathatcausedtheevent Specifications Electrical Supply 9 to 14 Current Consumption 35mA quiescent 100mA when active Environmental Operating Temperature 10 C to 55 C Maximum Humidity 95 non condensing Physical Dimensions 170mm x 140mm x 35mm Packed Weight 200g approx Standards The Premier ComGSM module conform to European Union EU Low Voltage Directive LVD 73 23 EEC amended by 93 68 EEC and Electro Magnetic Compatibility EMC Directive 89 336 EEC amended by 92 31 EEC and 93 68 EEC The CE mark indicates that this product complies with the European requirements for safety health environment and customer protection This product is suitable for use in systems designed
4. a connector on the module and site the antenna as high as possible Unlock the SIM socket by sliding the locking tab downwards Insert the SIM card into the holder with the chamfered corner to the top left Push the holder back into position and lock the SIM by sliding the locking tab upwards The SIM card must be inserted before connecting the ComGSM module to NOTE the control panel and must not be removed until after the power supply to the ComGSM module has been deactivated Set the option switches as required see page 3 Now connect the harness lead onto the control panel communication port COM 2 for the Premier 24 COM 1 or 2 for the Premier 48 88 168 640 The module should now be powered and the heartbeat LED 8 should be flashing Panel Configuration Before attempting to use the ComGSM module it must be correctly configured as follows 1 2 4 Enter Engineers Programming mode and select UDL Digi Options then select Com Port Setup Ensure Com Port is programmed as GSM Module Now select the Digi Options menu and make sure that Digi Option 1 is programmed for Digi is Enabled Now select Program Digi and ensure the following options are programmed for one of the ARC options a Protocol SMS Messaging Primary No The number of the recipients mobile telephone Secondary No Secondary mobile telephone number if required Account No Leave blank Dialling Attempts Program as required Repor
5. n Manual Antenna connection Tamper switch 3 Com1 data connection to Premier control panel Engineer keypad connector for future use 8 Option switches see table below 6 Status LED s see table below Audio connector for future use Heartbeat LED 9 SIM card socket Option Switches The option switches function as follows Off On When the tamper is open the GSM signal is reported as NO signal GSM signal level is reported as normal For future use leave in OFF position For future use leave in OFF position Toggle to perform a Reset Status LEDs The three status indicate the following Off On Flashing GSM NOT Ready GSM Ready GSM Communicating Panel NOT Ready Panel Ready Panel Communicating Dim Low Signal No Signal Bright Good Signal N A Installation The ComGSM module should be installed as close to the control panel as possible so that the harness lead supplied with the unit is able to plug onto the control panel communication port 1 Route the harness lead into the module housing using the top left cable entry and plug the connector onto COM1 INS315 3 ComGSM Module Installation Manual Install the module in the required location using suitable fixings Route the other end of the harness lead into the control panel housing DO NOT CONNECT at this point Connect the GSM antenna to the antenn
6. t Areas Program as required Reports Program as required Config Program as required All three status LED s should now be on if status LED 3 is dim this indicates a low GSM signal level If the signal level is low try moving the antenna to improve the reception gt INS315 ComGSM Module Installation Manual Using the SMS Control Commands Control commands can be sent to the ComGSM module to allow remote control and integration of the alarm system 1 Select the send text message option on your mobile telephone 2 Enter the telephone number of the ComGSM module 3 Enter the text command see SMS Control Commands 4 Select send on your mobile telephone When using the SMS Control Commands shown in the tables below the following should be noted 2222 User code this must proceed all commands areas Areas 1 to 8 or A to P If the areas are not specified then all areas will be selected s Send back status report zones List of zones each zone must separated by a space e g 1 12 167 etc outputs List of outputs e g 1234 etc message A maximum of 32 characters Premier 24 SMS Control Commands Arm System un arm s arm the system and report back Part Arm System parm 1 2 3 s 5678 parm 1 part arm 1 the system no status Disarm System 5678 darm disarm the system no status Reset System 5678 reset reset the system Turn Outputs
7. to comply with PD 6662 2004 prEN 50131 1 2004 at Grade 3 and Environmental Class II Warranty All Texecom products are designed for reliable trouble free operation Quality is carefully monitored by extensive computerised testing As a result the Premier ComGSM module is covered by a two year warranty against defects in material or workmanship As the Premier ComGSM module is not a complete alarm system but only a part thereof Texecom cannot accept responsibility or liability for any damages whatsoever based on a claim that the Premier ComGSM module failed to function correctly Due to our policy of continuous improvement Texecom reserve the right to change specification without prior notice Premier is a trademark of Texecom Ltd INS315 7 www texe com Texecom Limited Bradwood Court St Crispin Way Haslingden Lancashire BB4 4PW England Technical Support Tel 44 0 1706 234833 Tel 44 0 1706 234811 Fax 44 0 1706 213187 Texecom Ltd 2006 INS315
Download Pdf Manuals
Related Search