ONECell25 Installation Manual
Contents
1. 5 lt HR lt 80 Absolute Humidity lt 24g m3 Altitude lt 2500 m Storage Environment Temperature 25 C lt T lt 55 C Relative Humidity HR 5 lt HR lt 80 Absolute Humidity lt 24g m3 Altitude lt 2500 m 5 2 Power Supply e External Power Supply OneAccess 200 240 VAC 20W 12V 1 7A e External Power Supply OneAccess 230 VAC 12W 12V 1A Using another power supply than the ones recommended by OneAccess causes the product warranty to be void 6 5 3 Dimensions The dimensions of the housing are Width 152 mm Height 26 mm Depth 102 mm 15 ONECELL25 Installation Manual 6 Installation Always unplug the power AC cable before any hardware maintenance operation 0 This chapter describes assembling disassembling operations 6 1 Opening Casing 1 Unlock the screw at the bottom of the product and remove it 2 Remove the cover by sliding horizontally the cover away from the bottom part of the casing EG ONECELL25 Installation Manual 6 2 1 Installing SIM Card The casing must be open The steps are the following Unlock the SIM card holder by sliding the locking metal piece as indicated on the picture below lez TE que S o NI S N Ps bro 8 10 8010903 Raise the SIM card holder in vertical position ONECELL25 Installation Manual 3 Insert the SIM card make sure the SIM card is inserted in th2. passwords If the factory restore option is set default OneAccess settings one can now use the factory restore procedure It is triggered as follows Power on the product The Status LED blinks very quickly then it blinks more slowly When all LEDs of the front panel are lit unplug the power cable Repeat the process three times and then let the router boot The restore operation will be done Configuration by Telnet SSH Console The default telnet console login password is admin admin It is highly recommended to change the default password from web interface to avoid intrusion from hackers The ONECell25 has many powerful features that cannot be configured and managed via the web Configurator Any user can use the console at own risks e lt may cause the web Configurator not to work properly e OneAccess only supports customers having with a maintenance contract with OneAccess and being certified trained users Getting Support on ONECell25 Please use this link to get more documents and help http www oneaccess net com en cell ONECELL25 Installation Manual Appendix A Console Cable Catalog reference 4 022 332 B 00 Ed A To PC serial port in terminal mode Configuration RJ45 P1 SIGNAL SUB D 9 Pts Female P2 1 TX 2 2 RX 3 3 GND 5 EN ONECELL25 Installation Manual
3. NECell25 interface will not be connected The problem can appear mostly with devices forced in such mode or with old Ethernet hub 8 2 Starting the Web Configurator Open a web browser and use the following URL http 192 168 1 1 OneAccess Web Support Pages Windows Internet Explorer go on http 1192 168 1 1 zi gt xl http 192 168 1 1 Fichier Edition http 192 168 1 1findex_en html Google G TL n A The web configurator developed by OneAccess uses intensively javascript It has been tested with Internet Explorer version 6 and 7 as well as Firefox 2 Using the web configurator with other web browsers may not work and are not supported by OneAccess You will be directed to a login page The default login is webadmin and the password is admin It is recommended to use the EDGE connection wizard to setup the EDGE connection Please consult the web user manual for more details ONECELL25 Installation Manual 8 3 8 4 8 5 Restoring Factory Settings It might happen that e Access passwords to the web interface are lost e New configuration parameters such as firewall or unknown LAN IP are such that you cannot connect to the ONECELL25 web configurator In that case the restore factory settings will help you because the following factory settings are restored e Software and web configurator loaded at manufacturing time e Factory configuration files e Factory default
4. ONECell25 Installation Manual February 2009 NETWORKS http www oneaccess ne t com ONEAC OneAccess 28 rue de la Redoute 92260 Fontenay aux Roses France The law of 11 March 1957 paragraphs 2 and 3 of article 41 only authorizes firstly copies and reproductions strictly reserved for use by copyists and not for general use and secondly analyses and short quotations for the purpose of example and illustration Therefore any representation or reproduction entire or partial made without the consent of the author or his representatives is illegal paragraph 1 of article 40 Any such representation or reproduction made in any manner whatsoever would therefore constitute an infringement of the law as sanctioned by articles 425 and in accordance with the penal code Information contained in this document is subject to change without prior notice and does not constitute any form of obligation on the part of OneAccess OneAccess and the distributors can in no case be held responsible for direct or indirect damage of any kind incurred as a result of any error in the software or guide Every care has been taken to ensure the exactitude of information in this manual If however you discover an error please contact OneAccess After Sales Service division February 2009 Issue ONECELL25 Installation Manual How to Read this Manual The present document is broken down into 7 chapters Chapter 1 Safety Instruction
5. e right position as shown on the picture below 4 Putthe SIM card holder in its former position and lock it E ONECELL25 Installation Manual 6 3 Wall Mounting The lower part of the router has 2 notches in order to enable wall mounting By installing two screws at the required distance the router can be hung on any vertical surface Instructions 1 Bore two horizontal holes separated by 80 mm of distance if the router is hung with the rear panel in the upper position 2 Mount both screws in each hole Do not screw them completely but leave a distance of 5 mm between the wall and the head of the screw 3 Hang the router gently and if necessary adjust the screws in the notches of the router Figure 4 Positioning of the notches 1 Rearpanelofthe router 3 Notches 2 Bottomofthe router 4 Distance between holes 80 mm ONECELL25 Installation Manual 6 4 Connections The external power supply is connected on the rear panel of the device The external power supply is delivered with the router package Connect the jack connector of the external power supply to the connector marked 12V 1A device connector recommended by OneAccess Using another power supply than the ones Ih The router shall not be used with another power supply than a power supply A recommended by OneAccess causes the product warranty to be void 20 ONECELL25 Installation Manual 7 Power up To pow
6. er up the device always follow these steps e Connect the DC power input jack from the power supply to the DC power input of the rear panel of the router e Connect the power supply to the AC mains 200 240 V AC Few seconds after power on the device performs a series of self tests and loads the software into memory RAM during which the STATUS LED on the front panel blinks At the end of software loading about 30 seconds e The STATUS LED light remains steady green if software initialization was successful e The STATUS LED blinks in case of software absence or error during software loading ONECELL25 Installation Manual 8 Getting Started When the router is delivered with the default OneAccess factory settings the router is configured as follows e FASTETHERNET 0 0 port is configured with the IP address 192 168 1 1 netmask 255 255 255 0 e DHCP server is enabled e HTTP server for fast web based configuration is enabled 8 1 Connect your PC Your PC should be configured to acquire its IP address via DHCP protocol alternatively you can assign a static IP address to your PC LAN interface in the network range 192 168 1 2 192 168 1 254 Connect your PC with a LAN cable straight or crossed the ONECell25 adapts to both wiring IK The Ethernet interfaces of the ONECell25 only support the 100 Mbps full duplex operations in auto sense mode If connected to devices in 10 mbps or half duplex the O
7. for Safety Laboratoire Gyl Technologie pour CEM Gyl Technologie Laboratory for EMC Le produit est marqu du symbole CE en application des directives cit es ci dessus The product is marked with the CE symbol in accordance with the directives mentionned above Responsable autoris Authorized signatory Directeur G n ral Chief Operating Officer Nom Name Denis BEHAGHEL La is M _ ONECELL25 Installation Manual 2 2 Standards The ONECell25 is designed in conformity with the standards listed hereafter provided that the basic housing modules interface boards and installation kits are mounted as recommended in the corresponding installation manual s Safety EN IEC 60950 1 2001 Safety of information technology equipment including electrical First Edition business equipment Environment Climatic physico chemical mechanic packing ETS 300 019 1 Environmental conditions and environmental testing for telecommunication equipment In use Class 3 1 Temperature controlled locations Storage Class 1 1 Weather protected partly temperature controlled storage locations Transportation Class 2 3 Public transportation Electromagnetic Compatibility immunity EN 55022 Information technology equipment Radio disturbance characteristics Limits and methods of measurement EN 55024 Information technology equipment Immunity characteristics Limi
8. lf duplex the ONECell25 interface will not be connected The problem can appear mostly with devices forced in such mode or with old Ethernet hub 3 2 Front Panel The front panel is provided with LEDS which inform about the status of several router functions Figure 1 Front panel EI ONECELL25 Installation Manual Leds OFF Green Blinking green Status Router is Switched On amp Reboot in switched Off Operational progress EDGE Not configured EDGE GPRS Traffic on or connection connection EDGE GPRS not established established IP Not used All IP interfaces are At least one IP up interface is down ONECELL25 Installation Manual 3 3 Rear Panel This section details the various types of ONECell25 rear panel so that the user can identify the interface type and port numbering The interface marking is indicated in bold and between bracket All the connectors are located on the rear panel 1 console port RJ45 CONSOLE 2 Ethernet ports RJ45 FASTETHERNET 1 0 and FASTETHERNET 0 0 1 connectors for GSM antenna ANTENNA Input for the external power supply connector DC input jack 12V 1A CONSOLE Figure 2 Rear panel 3 4 Motherboard The motherboard provides e Router resources CPU DSP memory RAM and Flash e Standard router interfaces console interface Fast Ethernet and LEDs e An EDGE GPRS radio module supporting a SIM card EN ONECELL25 Installati
9. mity ss 7 2 2 Standards sieste nn miam en nn a hier ni nn 8 Router Description urna 9 3 1 Hardware Description rei 9 2 Front PanelsAsc aaa iaia LA ei Mai Ala a Re ten lee ele 9 3 3 ReanPan elitc tritate dattero talents debt diated agate tbe Bide Motherboard 6 OO a eit Interface Description 4 1 LAN 10 100 Mbps Interface FASTETHERNET 13 4 2 Gonsole port CONSOLE iii ddr 14 Technical Characteristics 5 1 Climatic Environment 52 AA A olii 5 35 A O AIAR toute Install Ri ii EL G l O peningiGasing i snc A A 16 6 2 Installing SIM Gard e eine aa 17 6 3 Wal Mounting iii diia 19 64 GONNEGHONS mira 20 LO A ie ea it 21 Getting A arene ri ei i ee ni cale I o iii 22 BAP Connect your PCs ie Aaa 22 8 2 Starting the Web Configurator sis 22 8 3 Restoring Factory Settings iii ies 23 8 4 Configuration by Telnet SSH Console 23 8 5 Getting Support on ONECELL25 ooo ee eeceeeeeeeeeeeeeeeeeeeeeeeeeeeaeeeesaeseeeaesaeesaeseeeeeeaeeneeeateaes 23 Appendix A Console Gable e AT aaa 24 ONECELL25 Installation Manual 1 Safety Instructions The following symbol instructs the user to read the manual carefully before any connection LIK 1 1 Connection to Power Supply To connect the power supply always follow these steps e Connect the DC input jack from the power supply to the DC 12V p
10. on Manual en 55 da ea gt of Figure 3 Motherboard ONECELL25 Installation Manual 4 Interface Description 4 1 LAN 10 100 Mbps Interface FASTETHERNET 4 1 1 Characteristics 100Base TX Full duplex Auto negotiation Auto MDI MDX duplex operations in auto sense mode If connected to devices in 10 mbps or half duplex the ONECell25 interface will not be connected The problem can appear mostly with devices forced in such mode or with old Ethernet hub I The Ethernet interfaces of the ONECell25 only support the 100 Mbps full A 4 1 2 Meaning of LED Colors Lit green Led Link active Blinking yellow Led Traffic in progress 4 1 3 Connector Pinout RJ45 Connector 4 1 4 Cables A standard Ethernet cable is needed shielded UTP Cat 5 EG ONECELL25 Installation Manual 4 2 Console port CONSOLE 4 2 1 Characteristics RS 232 9600 bps 8 bits 1 bit for stop no parity No flow control 4 2 2 Connector Pinout RJ45 Connector TX Transmission RX Reception NC Not connected GND Ground A console cable for router configuration and maintenance only requires TX RX and GND to be connected 4 2 3 Cables The console cable is defined in Appendix A ETS ONECELL25 Installation Manual 5 Technical Characteristics 5 1 Climatic Environment Operating Conditions Temperature 0 C lt T lt 457T Relative Humidity HR
11. ose marking on the router back panel is CONSOLE The interface is SELV It must be used only for indoor applications and connected to V 24 interfaces which are also designed as SELV GSM Antenna The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co located or operating in conjunction with any other antenna or transmitter ONECELL25 Installation Manual 2 2 1 Directives and Standards Declaration of Conformity D claration de conformit suivant les directives R amp TTE DBT et CEM Declaration of Conformity according to R amp TTE LVD and EMC directives ONE_CELL25 Routeur et adaptateur de r seau Router and network adapter Tension d alimentation Supply voltage 200 240 Vac 20 W 50 60 Hz 12V 1A Nous d clarons que ce produit est pr sum conforme aux exigences essentielles applicables des directives suivantes du Parlement Europ en et du Conseil la Directive R amp TTE 1999 5 CE du 9 mars 1999 concernant les quipements hertziens et les quipements terminaux de t l communications et la reconnaissance mutuelle de leur conformit la Directive Basse Tension 2006 95 EC du 12 d cembre 2006 concernant le rapprochement des l gislations des Etats Membres relatives au mat riel lectrique destin tre employ dans certaines limites de tension la Directive CEM 2004 108 EC du 15 d cembre 2004 relative au ra
12. ower input on the rear panel of the router e Connect the power supply to an AC electrical outlet 200 240 VAC Plugging in the power supply turns on the router device The AC input is the part you must disconnect first For safety rea sons you shall be able to easily access this part Ih Unplug the AC input before assembling disassembling any part on the o 1 2 Overcurrent Protection The product requires that the building s electrical installation is designed for protection against short circuit over current protection A fuse or circuit breaker no larger than 240 VAC 10A must be used on the phase conductors 1 3 Safety Level of Interfaces 1 3 1 LAN Interface 10 100 Mbps FASTETHERNET This section is related to interfaces whose marking on the router back panel is FASTETHERNET The Ethernet 100 Mbps auto sense has a SELV Safety Extra Low Voltage interface They must be used only for indoor applications connected to a 100 Mbps interface which has also the SELV characteristics Gi ONECELL25 Installation Manual 1 3 2 1 3 3 duplex operations in auto sense mode If connected to devices in 10 mbps or half duplex the ONECell25 interface will not be connected The problem can appear mostly with devices forced in such mode or with old Ethernet hub Ih The Ethernet interfaces of the ONECell25 only support the 100 Mbps full A V 24 Interface CONSOLE This sections is related to the interface wh
13. pprochement des l gislations des Etats membres concernant la compatibilit lectromagn tique et abrogeant la directive 89 336 CEE We declare that this product has been given a presumption of conformity with the applicable essential requirements of the following directives of the European Parliament and of the Council R amp TTE Directive 1999 5 EC of march 9 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity Low Voltage Directive 2006 95 EC of december 12 2006 on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits EMC Directive 2004 108 EC of december 15 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89 336 EEC Nous d clarons que les normes harmonis es suivantes ont t utilis es pour d montrer cette pr somption de conformit et ont donn lieu aux rapports de tests suivants disponibles sur demande We declare that the following harmonised standards were used to demonstrate this presumption of conformity and the results are included in the following tests reports which can be made available on request EN IEC 60950 1 2001 First Edition EN 55022 1998 EN 55024 1998 EN 300511 1995 07 EN 301489 1 2007 04 EN 301489 7 2005 11 Laboratoire GYL Technologie pour la S curit GYL Technologie
14. s This chapter provides the safety instructions for use and installation of the router Chapter 2 Directives and Standards This chapter details the list of standards which the device complies with Chapter 3 Router Description This section describes the router front and rear panels and the associated technical characteristics Chapter 4 Interface Description This section describes the router interfaces Chapter 5 Technical Characteristics This section describes technical characteristics such as operating conditions Chapier 6 Installation This chapter describes how to install SIM card and gives instructions to connect the router Chapter 7 Power up This chapter describes the device power up and how to monitor the self test progress Chapter 8 Getting Started This chapter explains to connect to the web Configurator and main operations with the product Appendix Connection description These chapters provide the pin out of cables that are compatible with the router E ONECELL25 Installation Manual Table of Contents Howto Read this Mandala ARR aa ia 3 iTable of Gontents rana aiar en en nn Inn Arts 4 Safety structions naisissa NC Ne ne 5 1 1 Connection to Power Supply sise 5 12 OV rc rrent Protection a iis aa ee anaes mt aie nine ni hoe ie 5 1 3 Safety Level of INterfaces cimil 5 Directives and StandardSs u suse natalia atalanta 7 2 1 Declaration of Confor
15. ts and methods of measurement EN 301 511 Harmonized EN for mobile stations in the GSM 900 and GSM 1800 bands covering essential requirements under article 3 2 of the R amp TTE directive 1999 5 EC EN 301 489 01 ElectroMagnetic Compatibility EMC standard for radio equipment and services Part 1 Common technical requirements EN 301 489 07 ElectroMagnetic Compatibility EMC standard for radio equipment and services Part 7 Specific conditions for mobile and portable radio and ancillary equipment of digital cellular radio telecommunications systems GSM and DCS Waste Electrical and Electronic Equipment 2002 96 EC The ONECell25 respects the European directive on the waste disposal from the electrical and electronics components Restricted use of Hazardous Substances RoHS 2002 95 EC The ONECell25 respects the European directive on the restricted use of Hazardous Substances in electric and electronic equipment ONECELL25 Installation Manual 3 Router Description 3 1 Hardware Description 3 1 1 Motherboard Interfaces The ONECell25 motherboard is equipped with the following interfaces The interface marking is indicated in bold and between brackets e 1 console port CONSOLE e 2 Ethernet port LAN 100 BT FASTETHERNET The Ethernet interfaces of the ONECell25 only support the 100 Mbps full A duplex operations in auto sense mode If connected to devices in 10 mbps 7 or ha
Download Pdf Manuals
Related Search