Installation Manual
Contents
1. Installation Manual Fibrain Optical Clouser PC ES 2024 M Aplications PC ES 2024 type of fiber closure is a fiber optic cable splice of multiple purposes which can connect and protect cables The fiber closures are suitable for protecting fiber cable splices in straight through and branching applications It can be placed in underground aerial wall mounting pedestal or direct buried hand hole mounting and duct mounting applications We always aim to the R amp D of Communication equipment Our fiber closures can improve the operation of your network communication system Closure is suitable for the applications up to 240 single fibers which can cover most of the applications in the long distance transmission and local fiber distribution networks like Fiber To The Home Fiber To The Curb FITH FITC It can be applied to areas such as underground aerial pedestal or direct buried HM Specifications Type Size mm Single Max Quantity of the The diameter of the CcoxH Capacity core splice tray suitable optic cable PC ES 2024 260x465 240 1 10 co 6 c017 5 do23 mm Weightkg Entrances Aijroroof type Material Reinforced core 5 45 7 Heat Shrink ABS PC Steel wire WE Maintechnical data Environment temperature 40C 55C Max capacity 240 cores using single core fiber Range of the suitable diameter of the cable do6 mm do17 5 do23mm Airoroof performance Airing pressure inside bo2. PC ES 2024 f IPE fee 6868 4 8908 LY i Wc i fhar antic SOIUTIONS YA J E tiber Optic sulU UUS f XL sAN Tre Hi m Eii E li cf i i If a a ti li Y 3 Installation of fiber closure Ve Insert cable into fiber closure Rub and clean the inlet ports and the cable with a piece of sandpaper to allow the sealing adhesives inside the heat shrink tube to be attached to each side around Wrap 10cm long cable with silver tape to protect cable inlet sheath 6cm long cable was covered by heat shrink tube Heating heat shrink tube Push the heat shrink tube up to the cable inlet port and heat the tube but not let the fire close to the inlet port When using dual type heat shrink tube inset the metal branching clip as the figure shown before heating Note When heating the tube heat the tube around the cable equally Distribution protection and fix of the fibers Distribute the fiber according to require and then let the fiber through the PVC transparent hose and fixed at entrance of fiber tray by nylon tie Splices fibers and coil surplus fibers Fusion and splice fibers and coil surplus fibers on bracket using an approved splicing method then cover the splice tray cover after splice fibers Assembling the closure After install of cables put sealing loop on case then place the dome shaped cover onto the bottom portion Fasten the dom
3. e shaped cover and the bottom portion together with a plastic hoop Fiber testing and sealing test It s possible to test after the closure are pressurized and it s possible to protect optic cables with earthing device Pressure testing valve is optional Fix the fiber closure a Fix the hanger on the concrete pole with the M10 560 screw then tighten the nut b Fix the body of the fiber closure and tighten the nut WM Note Using the six small cable inlet ports the diameter of the cable should not be more than 17 5mm if the big port it should not be more than 23mm
4. g being about 180cm e Remove the unnecessary cable sheath from the marked point with a sheath stripper Note 1 Be sure not to damage the fiber Note 2 Do not use any damaged cable Note 3 While remove the cable sheath please do not cut twist or damage fiber coat Reserve enough length to ensure repair and maintenance in case an accident happened e Cut off the extra reinforced core about 5cm from the removing point on the sheath 3 Installation of fiber closure e Check the specified type and all the accessories of the fiber closure D e Open the fiber closure Unlade the locked device on plastic hoop open plastic hoop in order to separate the cover and bottom Note Because the sealing performance is predominant please be careful when separating the cover and bottom so as not to damage the case Check the specified type and all the accessories of the fiber closure e Insert cable into fiber closure Select the appropriate cable inlet ports and cut less than 5mm from the applicable ports with a saw or other suitable Tools Insert the removed cable into the heat shrink tube first then into the inlet port Fix the reinforced core and fiber cable a Place the reinforced core plug in the device of fixing reinforced core then tighten the bolts using a screwdriver ora wrench b Fix the cable on the bracket with compact device Note Be careful not to damage the fiber Installation Manual Fibrain Optical Clouser
5. ity Application l Heat shrink tube 6 pieces Optic cable heat shrink and sealing qo30x 150 mm 2 Dual heat shrink tube 1 piece Dual optic cable heat shrink and sealing co75x150 mm oe Pressure testing valve set Testing after closure sealed 4 Silver tape set Fiber protection J Sand paper set Cleaning 6 Branching clip 1 set Branching optic cables WW installation flow chart Open the closure Determine the length of fiber cable to be fixed and stripped inside Strio off protective coats of fiber cable and fiber Separate fiber cores and prepare work before fixing fiber cable Fix reinforced core and fiber cable heat shrink seal Check up thoroughly 3 Installation Manual Fibrain Optical Clouser PC ES 2024 WM Direction 1 Preparation e Please check the cable structure and the fiber type before starting installation Different types of fibers can t be spliced together e Seal the splicing part perfectly to minimize damages to the cable caused by moisture Don t apply any impact to the splicing part e Keep the working place free from moisture and dust Don t give any impact on the cables Don t bend or entwine cables e During the sheath stripping and the closure assembling procedures use permitted tools according to the approved fiber optic splicing standard in yourregion 2 Cable installation 2A e Mark the cutting point on the cable the length of strippin
6. x 100Kpa pointer immovabllity after 24 hours or no air bell within 15min when parked in the common temperature water e Re encapsulation performance no change in the index of air oroof performance after three times of repeat encapsulation e Insulation resistance 22 X 104MQ e Voltage resistance strength under the effect of 1S5kvDC Imin non puncture no arc over HM structure and Components Installation Manual Fibrain Optical Clouser PC ES 2024 E Accessories Main components No Name Quantity Marks l Cover l piece Height x Diameter 465x260 mm 2 Fiber splice tray set 3 Base set Fixing internal and external structures 4 Plastic hoop set Fixing bottom and cover si Seal fitting l piece Waterproof and sealing 6 Bilateral entwined tray set The fibers reserved to be entwined 7 Earthing device set Deriving metal parts of fiber cables in closure for earthing NM Accessories and tools No Name Quantity Application l Heat Shrinkable sleeve l piece Fiber fusion and protection 2 Nylon tie 16 piece Fixing fiber with protective coat 2 Pole hoop 1 set Fixing for closure on pole 4 Labeling paper piece Fiber labeling J Insulating tape piece 6 PVC transparent hose l piece Protect fiber 30mm Installation Manual Fibrain Optical Clouser PC ES 2024 E Optional Accessories No Name Quant
Download Pdf Manuals
Related Search