USER'S MANUAL @ BEDIENUNGSANLEITUNG I MANUEL D
Contents
1. s life e Only use the equipment indoors e Do not expose to flammable sources liquids or gases e Always disconnect the power from the mains when equipment is not in use or before cleaning Only handle the AC cable by the plug Never pull out the AC plug by pulling the AC cable e Make sure that the available voltage is between 230v e Make sure that the AC cable is never crimped or damaged Check the equipment and the AC cable periodically e f the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again e f the equipment has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature e f your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Cameo dealer for service e Only use fuses of same type and rating e Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CON TAINS NO USER SERVICEABLE PARTS e Never use any accessories or modifications not authorized by the manufacturer of this unit e Choose a location for operation where the unit is protected from vibration and where a fixed mounting position is provided In2. 20 mm Glass 0 5 A Fast Blow CONTROL amp PROGRAMMING Data input Locking 3 pin XLR male socket Data output Locking 3 pin XLR female socket Protocols DMX 512 USITT DMX channels 4 6 selectable CLP 64 WEIGHT amp DIMENSIONS WITHOUT BRACKET Length 270 mm Width 270 mm Height 263 mm Weight 2 3 kg Beam angle 25 POWER Power consumption 30W AC input 230 V 50Hz FUSE Main 20 mm Glass 0 5 A Fast Blow CONTROL amp PROGRAMMING Data input Locking 3 pin XLR male socket Data output Locking 3 pin XLR female socket Protocols DMX 512 USITT DMX channels 4 6 selectable LIMITED WARRANTY This Limited Warranty applies to the Adam Hall LD Systems Defender Palmer Cameo and Eminence branded products The statutory warranty rights towards the seller are not affected by this guarantee In fact it justifies additional independent warranty claims towards Adam Hall Adam Hall warrants that the Adam Hall product you have purchased from Adam Hall or from an Adam Hall autho rized reseller is free from defects in materials or workmanship under normal use for a period of 2 or 5 years from the date of purchase The Limited Warranty Period starts on the date of purchase In order to receive warranty services you are required to provide proof of the purchase date Your dated sales or delivery receipt showing the date of purchase is your proof of the purchase date Should products of the brands named above be i
3. AE Mee ERNE Ca mooo colours of light MANUEL D UTILISATION MANUAL DE USUARIO INSTRUKCJA OBS UGI MANUALE D USO E iet bus CA kit er N SC up UNAT SECOS AN HE NN AAA AA AAP NEA pira ubo HS CECE Et EE CO Cee NG K CA q ee ee STAND ALONE MODE GREEN SOLUTION PAR 96 64 CAN 10 MM LED CANS CLP56RGB10 CLP64RGB10 EE LD SYSTEMS Thank you for choosing Cameo Lights We have designed this product to give you reliable operation over many years Please take a few moments to read these instructions carefully as we want you to enjoy your new Cameo Lights products quickly and to the fullest Further information about Cameo Lights check our website WWW GAMEOLIGHT COM ESPANOL e Z PAR 96 64 CAN 10 MM LED CANS CI P56RGB10 CLP64RGB10 HOSLNAG Can Lt rt M T t A 4 KO TAN Cine OSES CEA CA BIS ARE z EC e E LD SYSTEMS PREVENTIVE MEASURES e Never let the AC cable come into contact with other cables Handle the AC cable and all mains voltage connec tions with particular caution e Never remove warning or informative labels from the equipment e Do not open the equipment and do not modify the equipment e Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the system
4. case of overhead mounting follow appropriate rigging rules and your country s regulations for rigging safety e Before plugging the AC cable in the wall outlet check whether the AC mains voltage and frequency is the same as this product is specified for Whenever your AC plug should not match the wall outlet contact your dealer immediately e f fluids have spilled into the unit or small parts have intruded the unit immediately switch off the unit and hand it over to the authorized service for a security check e Disconnect the unit from AC supply by pulling the AC plug out of the wall outlet or the unit s AC socket during a thunder storm in order to avoid any damage on the unit due to AC voltage peaks e n cause of not correct function of this unit or damaged AC cable or other damaged parts pull immediately the AC plug out of the wall outlet and hand the unit over to the authorized service for a security check e To meet all aspects of functionality and security during maintenance work to be preformed on this unit all parts should be replaced by genuine spare parts Consequently take care of your dealer or maintenance compa ny to be authorized by the manufacturer DEUTSCH ESPANOL ITALIANO OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation may lead to danger e g short circuit b
5. e z z STATIC COLOUR MODE Press the mode button and use the up and down buttons to select one of the 7 desired colours 1 Red 2 Green 3 Blue 4 Yellow 5 Cyan 6 Purple 7 White uda pF FL o o MODE UP Down COLOUR CHANGING MODE Press the mode button to select the Colour Change programme The unit will then run in Colour x change mode Press the up and down buttons to select the colour change speed from 0 99 MODE UP Down Tu COLOUR FADING MODE Press the mode button to select Fade mode The unit will then run in colour fade mode Press L a the up and down buttons to select the fade speed from 0 99 m MODE UP Down AUTO RUNNING MODE Press the mode button to select Auto mode The unit will then run automatically through all of the built in programmes The run speed can be pre set via the speed of the colour change ri and colour fade modes o MODE UP Down SOUND CONTROL MODE Press the mode button to select sound mode The unit will then run via the sound Press the Z up and down buttons to adjust the sound sensitivity levels LI MODE UP Down SLAVE MODE CE Press the MODE button to enter SLAVE MODE LI L H Link the slave unit and the master unit via DMX cable The slave unit will follow in sequence with the master unit o o Oo MODE UP Down Emm LD SYSTEMS TROL MODE The Cameo PAR 56 CAN has two DMX modes to choose from 4 channel or 6 Cha
6. ffective even if you have advised Adam Hall of an authorized representative of Adam Hall of the possibility of any such damages This limitation of liability however will not apply to claims for personal injury This Limited Warranty gives you specific legal rights You may also have other rights that may vary from state to state or from country to country You are advised to consult applicable state or country laws for a full determina tion of your rights REQUESTING WARRANTY SERVICE To request warranty service for the product contact Adam Hall or the Adam Hall authorized reseller from which you purchased the product EC DECLARATION OF CONFORMITY These devices meet the essential requirements and further relevant specifications of Directives 2004 108 EC EMC and 2006 95 EC LVD For more information see www adamhall com CORRECT DISPOSAL OF THIS PRODUCT ELECTRICAL WASTE X Applicable in the European Union and other European countries with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncon trolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or
7. he product by use of spare parts not manufactured or sold by Adam Hall by modification or service by anyone other than Adam Hall These terms and conditions constitute the complete and exclusive warranty agreement between you and Adam Hall regarding the Adam Hall branded product you have purchased SIVONVYS HOSLNAG BIS ARE 3 a 5 2 O LD SYSTEMS MANUFACTURER S DEC DEUTSCH ESPANOL ITALIANO LIMITATION OF LIABILITY If your Adam Hall branded hardware product fails to work as warranted above your sole and exclusive remedy shall be repair or replacement Adam Halls maximum liability under this limited warranty is expressly limited to the lesser of the price you have paid for the product or the cost of repair or replacement of any hardware components that malfunction in conditions of normal use Adam Hall is not liable for any damages caused by the product or the failure of the product including any lost profits or savings or special incidental or consequential damages Adam Hall is not liable for any claim made by a third party or made by you for a third party This limitation of liability applies whether damages are sought or claims are made under this Limited Warranty or as a tort claim including negligence and strict product liability a contract claim or any other claim This limi tation of liability cannot be waived or amended by any person This limitation of liability will be e
8. internal microphone e Colour change speed and strobe effect adjustable via control panel e Multi colour changes e RGB Colour mixing e Master Slave functions e Sound activated e Rugged compact housing e Double bracket e Power consumption 20 W e Beam angle 25 degrees e Long life LEDs OPERATING INSTRUCTIONS CONTROL FEATURES PAR 64 CAN CLP64RGB10PS polished CLP64RGB10BS black e 4 6 channel DMX e Blackout Dimmer Strobe e Individual control of Red Green and Blue LEDs FEATURES e 183 LEDs e Ultra Bright 10mm RGB LEDs e Sound control via internal microphone e Colour change speed and strobe effect adjustable via control panel e Multi colour changes e RGB Colour mixing e Master Slave functions e Sound activated e Rugged compact housing e Double bracket e Power consumption 30 W e Beam angle 25 degrees e Long life LEDs The Cameo PAR LED CAN is a DMX 512 controllable full RGB colour mixing spot made up of high efficiency and super bright 10 mm LED s There are three colour groups red green and blue whose intensity can be controlled individually allowing the creation of an unlimited range of colours The Cameo LED light will operate in Stand alone Master Slave Sound activated and via DMX 512 control O amma sw sw O PADDER Ed ca im ne AE DMX IN m wx our O HOSLNAG BIS ARE z C Z e E LD SYSTEMS MODE SELECTION DEUTSCH ESPANOL
9. n need of repair within the limited war ranty period you are entitled to warranty services according to the terms and conditions stated in this document This Limited Warranty extends only to the original purchaser of this Adam Hall branded product and is not trans ferable to anyone who obtains ownership of the Adam Hall branded product from the original purchaser During the Limited Warranty Period Adam Hall will repair or replace the defective component parts or the product All component parts or hardware products removed under this Limited Warranty become the property of Adam Hall In the unlikely event that your Adam Hall product has a recurring failure Adam Hall at its discretion may elect to provide you with a replacement unit of Adam Hall s choice that is at least equivalent to your Adam Hall branded product in hardware performance Adam Hall does not warrant that the operation of this product will be uninterrupted or error free Adam Hall is not responsible for damage that occurs as a result of your failure to follow the instructions included with the Adam Hall branded product This Limited Warranty does not apply to wear parts e g accumulator to any product from which the serial number has been removed or that has been damaged or rendered defec tive as the result of an accident in case of misuse abuse or other external causes by operation outside the usage parameters stated in the user s documentation shipped with t
10. nnel To access the 4 Channel mode press the mode button to show a red r1 ri dot illuminated under the first digit of the DMX address The unit is now ready Li LI Red Dot for use in 4 channel mode CHANNEL VALE FUNCTION woo UP Down 000 255 RED 0 100 O CH2 000 255 GREEN 0 100 CH3 000 255 BLUE 0 100 zu mm 5 CH4 000 255 MASTER DIMMER 0 100 T Lt Lt To access the 6 Channel mode press the mode button to show NO red dot under the first digit of the DMX address The unit is now ready for use in 6 channel mode e 6 MODE UP Down z pou wn GREEN 0 100 BLUE 0 100 Master dimmer 0 100 e No function Strobe Speed Adjust Sound Sensitivy Adjust 6 No function Colour mixing RGB colour change 7 colour change 224 255 Sound activation To change from 4 channel to 6 channel mode press ONLY the mode button repeatedly until you return to the DMX control mode DAISY CHAIN CONNECTION 1 Connect the male 3 pin connector side of the DMX cable to the output female 3 pin connector of the first fixture 2 Connect the end of the cable coming from the first fixture which will have a female 3 pin connector to the input connector of the next fixture consisting of a male 3 pin connector Proceed to connect from the output as stated above to the input of the following fixture and so on I p e LD SYSTEMS DMX LINKING DMX 512 DMX Digital Multiplex is a universal pr
11. otocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fixture DMX data are sent as serial data that travel from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX LINKING DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the midd le When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain DEUTSCH ESPANOL Please check out our comprehensive DMX cable choices out of our Adam Hall product lines 3 STAR 4 STAR and 5 STAR Also remember that DMX cable must be daisy chained and cannot be split e z NOTICE e Be sure to follow figures 2 amp 3 when making your own cables Do not connect the cable s shield conduc
12. their local government office for details on where and how they can recycle this item in an enviromentally friendly manner Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal WEEE DECLARATION K Your LD Systems product was developed and manufactured with high quality materials and components wich can be recycled and or reused This symbol indicates that electrical and electronic equipment must be disposed of separately from normal waste at the end of its operational lifetime Please dispose of this product by bringing it to your local collection point or recycling centre for such equipment This will help to protect the environment in which we all live BATTERIES AND ACCUMULATORS A The supplied batteries or rechargeable batteries can be recycled Please dispose of them as special waste or return them to your specialist dealer In order to protect the environment only dispose exhausted batteries Adam Hall GmbH all rights reserved The technical data and the functional product characteristics can be subject to modifications The photocopying the translation and all other forms of copying of fragments or of the integral ity of this user s manual is prohibited HOSLNAG BIS ARE I EC e
13. tor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behaviour common DMX 512 out 3 pin XLR DMX 512 in 3 pin XLR HOSLNAG SPECIAL NOTE LINE TERMINATION e When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behaviour Termination reduces signal transmission prob lems and interference It is always advisable to connect a DMX terminator resistance 120 Ohm 1 4 W between pin 2 DMX and pin 3 DMX of the last fixture Using a cable terminator Art No K3DMXT3 will decrease the possibilities of erratic behaviour TONVISI e Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 Pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The chart below details the correct cable conversion XLR socket GND screen SI Si N N C XLR socket GND screen Signal Signal I i o PNG NE DEUTSCH ESPANOL ITALIANO EE LD SYSTEMS SPECIFICATIONS CLP 56 WEIGHT amp DIMENSIONS WITHOUT BRACKET Length 250 mm Width 250 mm Height 230 mm Weight 2 1 kg Beam angle 25 POWER Power consumption 20W AC input 230 V 50Hz FUSE Main
14. urns electric shocks lamp failure etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and property WARNING 1 Do not look into the beam from a distance of less than 40 cm 16 inches 2 Do not stare into the beam for extended periods at a short distance 3 Do not view the beam directly with optical instruments such as magnifiers CAUTION MSK DONOT OPEN CAUTION To reduce the risk of electric shock do not remove cover or back No user serviceable parts inside Refer servicing to qualified personnel to the presence of uninsulated dangerous voltage within the product s enclosure that may be of The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user sufficient magnitude to constitute a risk to persons important operating and maintenance servicing instructions in the literature accompanying the 1 The exclamation mark within an equilateral triangle is intended to alert the user to the presence of appliance HOSLNAG BIS ARE z a e LD SYSTEMS INTRODUCTION DEUTSCH ESPANOL e z CONTROL FEATURES PAR 56 CAN CLP56RGB10PS polished CLP56RGB10BS black e 4 6 channel DMX e Blackout Dimmer Strobe e Individual control of Red Green and Blue LEDs FEATURES e 108 LEDs e Ultra Bright 10mm RGB LEDs e Sound control via
Download Pdf Manuals
Related Search