ATC-2000WF User's Manual
Contents
1. PIN RS 422 RS 485 1 T 485 2 T 485 3 R NC 4 R NC 5 VIN VIN 6 VIN VIN 1 6 Connecting the Hardware This section describes how to connect ATC 2000WF to serial devices for first time testing purposes We cover Wiring Requirements Connecting the Power Connecting to the Network You should also pay attention to the following items Use separate paths to route wiring for power and devices If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point Connecting the Power Connect the 9 36 VDC power line with ATC 2000 power jack When the power is properly supplied the Link and DIS LED will light in red and yellow color until the system is ready at which time the Link LED will be put out and DIS PWR LED still light Connecting to a Serial Device Connect the serial data cable between ATC 2000WF and the serial device 1 7 Top Panel LED Indicators LINK Indicate WLAN status DIS Indicate WLAN status ACT It will flash when transmit the data from WLAN to serial or from serial to WLAN PWR Indicate the Power supply Detail for LINK DIS Led indicate LINK WLAN Connecting WLAN Disconnect Setup Command 2 0 Initial Configuration When setting up your ATC 2000WF for the first time the first thing you should do is configure the IP address Select one of the initial IP Address configuration methods to configure OFF ON 2 1 Fact2. Other Commands PSMOD x Where x is the power saving mode 1 ON 0 OFF RES Reset as if a Hardware reset was applied DEF Restores all settings to Factory Default MAC Read Only command that display the unique MAC address VER Read Only command returns Firmware Version Number HELP Displays list of all available Commands along with abbreviated format LIST Displays alphabetic readout of all Mini b Settings
3. ATC 2000WF User s Manual Copyright 2007 ATC Technology Co Ltd Rev 1 0 All rights reserved The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement Copyright Notice Copyright 2007 ATC Technology Co Ltd All rights reserved Reproduction without permission is prohibited Trademarks ATC is a registered trademark of The ATC Technology Co Ltd All other trademarks or registered marks in this manual belong to their respective manufacturers Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of ATC 1 0 Introduction ATC 2000WF Series of wireless serial device servers give you an easy way to connect your RS 232 422 485 serial devices to a WLAN The 1 port ATC 2000WF and 2 port ATC 2002WF are ideal for environments where a LAN is not available or where serial devices are moved frequently 1 1 Overview The RS232 connection application has been used for a long time RS232 cable has limitations in distance WLAN Wireless Local Area Network has become a worldwide standard protocol for wireless applications There are many applications for using RS232 connection over WLAN including POS data capture telemetry PLC controllers remote control vending machine industrial control and others The device that supports connection over WLAN is called as Wireless to Serial Se
4. al Server eOne Removable Antenna RP SMA Reverse Polarity SMA eOne CD containing Set Up Utility User Manual and various Application Notes eOne AC Power Adapter with DC barrel plug 2 1mm ID 5 5mm OD eOne RS 232 DB9 Female Cross Configuration cable eOne Quick Installation Guide 1 3 Product Features eConnect serial device to Wireless LAN network e802 11b Wireless LAN compatible with 802 119 eWEP support for 64 bit and 128 bit encryption ePassword authentication and IP filter eAd Hoc peer to peer Infrastructure Pseudo IBSS mode support eRS 232 Serial Port for console e3 in one RS 232 422 485 port can be freely chosen at up to 57 6 Kops eVersatile socket operation modes including TCP IP UDP IP HTTP ARP DHCP client eEasy to use Windows Utility for mass installation eSupports Windows Virtual COM drivers eLEDs indicate LINK DIS ACT and PWR WLAN Radio Features Protocol Type 802 11b standard compliant Operating Range Open Environment 1000 ft 300m Office Environment 100 330 ft 30 100m Security WEP Wired Equivalent Privacy 64 and 128 bit encryption Network Mode Infrastructure mode Ad Hoc mode 1 4 Serial Communication Parameters No of ports 1 ATC 2000WF Interface RS 232 422 485 Port Type DB9 Male and six bit terminal Baud Rate Options 9600 38400 57600 bps Data Length Options 8 bits Parity options None Stop Bits Options 1 bit Flow Control Hardware or none Serial UART Buffer 256 bytes inp
5. here x is the IP of this device MASK xxx xxx xxx xxx Where x is the Network Mask of this device GW Xxx xxx xxx xxx Where x is the Gateway of this device DHCP x Where x is the DHCP setting 1 ON 0 OFF Wireless LAN Commands CHAN x Where x is the channel setting 1 14 MODE x Where x Network Mode x a ad hoc b infrastructure p Pseudo IBSS SSID xxxxxxxxx Where x is the multi character SSID network name RATE x Where x is the Tx rate 1 2 5 11 mbps WEP x Where x is WEP key 0 OFF 1 64bit 2 128bit WK x yyyyyyyyyy Load WEP Encryption Key into WEP buffers 1 2 3 or 4 WKID x Where x is the Buffer of the WEP encryption key in use 1 2 3 or 4 AA x Where x is the authentication A Auto S Shared Key O Open Serial Port Commands BAUD x Where x is serial port baud rate 0 115200 1 57600 2 38400 3 9600 FCTL x Where x is Serial Flow Control setting 1 ON O OFF PORT xxxxx Where x TCP Serial Port Number Default value is 1001 Server Client Settings RMODE x Where x is CLIENT or SERVER setting for this device RIP xxx xxx xxx xxx Where x is Server Target Remote IP when this device is in Client mode RPORT xxxxx Where x is Server Target Remote PORT when this device Client mode Enter Command Mode SetUpWLAN Gatekeeper Command Entry String Exit and Save Settings Commands EXIT Exits Command Mode but DOES NOT SAVE CHANGES SAVE SAVE Command Saves only but does not Exit Configuration Mode SE SAVES and EXITS Command Mode simultaneously
6. ork properly JET Lota echo 6 Press the backspace key located in the upper right corner of the keyboard continuously while powering on the ATC 2000WF PEELE LT eee ize eee ee See aa es ae BR ea el Sl eh 7 Sending a continuous backspace string to ATC 2000WF triggers it to switch 3 72 8 k Pi automatically from data mode to console mode 8 Start by configuring the IP address and WLAN under MS DOS Command Mode section for instructions on how to configure the rest of the IP settings 9 Choosing the Proper Operation Mode In this chapter we describe the various ATC 2000WF operation modes The options include an operation mode that uses a driver installed on the host computer and operation modes that rely on TCP IP socket programming concepts After choosing the proper operation mode in this chapter refer to Chapter 3 0 for detailed configuration parameter definitions Factory Default IP Address Network Setting IP 192 168 1 250 MASK 255 255 255 0 GW 192 168 1 254 DHCP OFF Wireless LAN Commands CHAN 11 MODE infrastructure SSID wlandemo RATE 11 mbps WEP OFF Serial Port Commands Baud Rate 38400 bps Serial Flow Control setting OFF TCP Serial Port Number 1234 3 0 Summary of Commands Listed by Functional Category These commands are explained in detail with more detailed functioning examples further in this document Network Commands IP xxx xxx xxx xxx W
7. ory Default IP Address ATC 2000WF is configured with the following default IP addresses WLAN Setting static IP IP Address 192 168 1 250 Netmask 255 255 255 0 2 2 Serial Console 38400 n 8 1 Before configuring the ATC 2000WF via the serial console turn off the power and use a serial cable to connect the ATC 2000WF to your computer s serial port We suggest using PComm Terminal Emulator which is available in CD driver to carry out the configuration procedure Firstly install PComm Terminal Emulator on your computer 1 Connect ATC 2000WF RS 232 serial port directly to your computers male RS 232 serial Port with RS 232 DB9 Female Cross Configuration cable 2 From the Windows desktop click on Start Programs PComm Lite Terminal Emulator 3 When the PComm Terminal Emulator window opens first click on the Port Manager menu item and select Open or click on the Open icon ES PComm Terminal Emulator Prolile Port Manager Help ajala FFEEF sf 4 The Property window opens automatically From the Communication Parameter page select the appropriate COM port for the connection COM1 in this example and 38400 for Baud Rate 8 for Data Bits None for Parity and 1 for Stop Bits Property 5 From the Property window s Terminal page select ANSI or VT100 for Terminal Type and click on OK If you select Dumb Terminal as the terminal type some of the console functions especially the Monitor function may not w
8. rver Through out the guide the 802 11g Wireless to Serial Server will be referred as the Server ATC 2000WF wireless serial device servers support automatic IP configuration protocols DHCP BOOTP and manual configuration via a handy web browser console Both IP configuration methods ensure quick and effective installation An external antenna increases the range of the wireless connection Users can position the adjustable antenna for maximum signal strength or even replace the antenna with their own for additional flexibility and scalability This feature is particularly useful when a serial device is connected in a high interference area As an added feature a signal strength indicator is located on the front panel to make it easier to troubleshoot connection Problems ATC 2000WF wireless serial device servers ensure the compatibility of network software that uses a standard network API by providing TCP Server Mode TCP Client Mode and UDP Mode The Real COM TTY drivers allow software that works with COM TTY ports to be set up to work over a TCP IP network in no time This excellent feature preserves your software investment and lets you enjoy the benefits of networking your serial devices instantly To make your management task easier the ATC 2000WF provides additional features such as password authentication IP filter WEP support for 64 bit and 128 bit encryption and SNMP support _1 2 Package Content eOne 802 11g Wireless to Seri
9. ut 256 bytes output Radio Characteristics Spread Spectrum Technology DSSS Direct Sequence Spread Spectrum RF Range 2 4 2 4835 GHz Data Rate 11 5 5 2 1 Mbps Modulation DBPSK for 1 Mbps DQPSK for 2 Mbps CCK for 5 5 11 Mbps Operation channels US 11 Europe 13 France 4 Spain 2 Japan 14 RF Power Output Typ 15 dBm Receive Sensitivity Typ BER 10E 5 83 dBm 11Mbps Power Power Supply 9 36VDC Current Tx 350mA Max Rx 210mA Power Saving Mode 80mA Software Windows based Driver with Multi Link Virtual Com Driver PC Set UP Utility User setup and device search software run on Windows XP 98 ME NT 2000 Network Protocol TCP IP UDP IP SNMP HTTP ARP DHCP client Mechanical Antenna PCB board mount antenna option or Ipex connector for external antenna and cable option Dimensions 95 x 76 x 26 mm Environmental Temperature Operating 0 to 55 C 32 to 131 F Storage 20 to 65 C 4 to 149 F Relative Humidity 95 non condensing Emissions EMC Certificate U S A FCC Part 15 Subpart C CE ETSI EN 300 328 EN 301 489 1 17 EN 55022 EN 61000 EN 50371 Certification Some models are already FCC Modular Certified for immediate public sale 1 5 Serial Port Pin Assignments RS 232 422 485 Pinouts RS 232 Pinout DB9 Female PIN RS 232 Input Output 2 RXD l 3 TXD O 5 GND 7 RTS O 8 CTS RS 422 485 Pinout SIX Terminal from Left
Download Pdf Manuals
Related Search