Stereo Sound & CD-ROM
Contents
1. SON YUTIL gt IN STALL Enter You will be prompted to select the target drive and subdirectory to which the audio utility software will be copy Afterwards you will be asked to enter the CD ROM drive letter and the monitor type J e color or mono The CD ROM drive letter should be the same as the one specified in the Autoexec bat file see Step 2 on page 16 Page 19 Stereo Sound amp CD ROM Upon successful completion of the installation you should find CDPALY BAT ESSVOL EXE SONYCD EXE EJECT COM LOCK COM and UNLOCK COM under the subdirectory that you selected or created on your hard disk This driver enables you to use your CD ROM drive as a regular audio CD player EJECT COM allows you to eject the CD tray from the CD ROM drive LOCK COM will lock your tray even if you push the eject bottom on the CD ROM front panel Run UNLOCK COM to re release the tray 4 5MITSUMI CD ROM Software The diskette labeled CD ROM Device Driver amp Audio Utility under the subdirectory CDROM MITSUMI contains the Mitsumi CD ROM device driver software and OPTIONALLY the Microsoft MS DOS CD ROM Extension file 1 e MSCDEX EXE Another subdirectory MTMUTIL contains the Mitsumi audio utilities in order for you to use the CD ROM drive as an audio CD player Please follow steps below to install the driver amp utilities NOTE The file MSCDEX EXE is not furnished unless the card is bundled with a CD ROM drive supplied by us Automatic CD2. The default setting is the CDROM directory of the boot drive Didevice name Specifies the name of the CD ROM drive 8 characters maximum This must be identical to the device name specified in the device driver in the CONFIG SYS file For example O C CDROM MSCDEX EXE D MSCD000 M n Specifies the number of sector buffers for temporary storage of the most recent disc data For example to specify ten sector buffers you would use O C CDROM MSCDEX EXE D MSCDO000 M 10 The installation program will set this value to 10 The default value is 4 NOTE The greater this value the better the CD ROM drive will perform However each buffer uses about 2K of memory and specifying too many buffers may slow down computer operation or interfere with other programs which have large memory usage requirements Using expanded memory see the E option in this section or loading MSCDEX EXE into high memory refer to your MS DOS Users Manual or Memoiy Manager Users Manual may allow you to Page 13 Stereo Sound amp CD ROM specify a larger number of buffers to enhance CD ROM performance and operate programs with large memory usage requirements simultaneously E Instructs the computer to use expanded memory 1f available For example O C CDROM MSCDEX EXE D MSCD000 E Note that you must first load an expanded memory driver before using this option If no expanded memory driver is load the following error message app
3. A CDROM P AN ASONI gt CDINSTL Enter This program will guide you step by step to setup CD ROM device driver parameters Please refer to the section below to learn more about how to change device driver parameters You may manually install the driver by completing the following steps Step 1 Use any text editor to add the following two lines to the file CONFIG SYS under your boot hard disk root directory Drive C in general O Device drive path CDMKE SYS Didevice name P xxx O LASTDRIVE drive letter Didevice name specify device driver name that is used by the Microsoft MS DOS CD ROM extension file MSCDEX MSCD000 is the commonly used device driver name when none is specified P XXX xxx 1s the I O port address as set on SI of the sound card The default is 320H Lastd rive letter Enter the proper drive letter name according to your system configuration For example if you already have 3 hard drives use f If this qualifier is not specified the default used by DOS is e Page 12 Stereo Sound amp CD ROM Step 2 Add the following line to the file AUTOEXEC BAT under your boot hard disk root directory Drive C in general O drive path MSCDEX Didevice name M n E V L i drive letter NOTE The above command line in the autoexec bat file should be placed entirely on one line drive path MSCDEX EXE Specifies the location drive and directory of the MSCDEX EXE file
4. both record and playback Selectable standard ADPCM or ESPCM for low bit rate compression Enhanced YAMAHA OPL3 16 bit stereo synthesizer 4 operators 20 voice channels 5 channel mixer Individually or simultaneously volume control for all mixer sources Output mixing for Line In Music Synthesizer CD Audio Wave and Microphone Input mixing for Line In Music Synthesizer CD Audio and Microphone Built in power amplifier Standard UART MIDI interface Standard IBM PC joystick interface Auto sensing different manufacturer s CD ROM drive No jumper setting needed Support Panasonic CR 522 B AT BUS CD ROM drive Support daisy chain up to four Panasonic CR 562 B CD ROM drives Support SONY CDU 31A CDU 33A CD ROM drive Support Mitsumi CRMC LU005S CRMC FX001D AT BUS CD ROM drive Transfer rate up to 2M Bytes per second Multiple I O port addresses selectable Page 3 1 2 1 3 CNI CN2 CN3 CN4 CN5 CN6 J1 J2 J3 J4 J5 J J7 VRI Card Figure Connectors Stereo Sound amp CD ROM J33 ag J6 ea JB parandorateanansnenoncncncn ene MM ronan freeeercrenntercer MEE CCL Core oor econ 7 Ma na anp a gta arara a a ee aaar a ae A a a hd AA C on m eanaan 34 pin connector for SONY internal CD ROM 40 pin connector for Mitsumi internal CD ROM 26 pin connector for Panasonic external CD ROM 20 pin connector for SONY external CD ROM 40 pin connector for Panasonic internal CD ROM 15 pin D SUB connector for J
5. internal Panasonic CD ROM drive 6 21 2 Install an internal Mitsumi CD ROM drive 7 2 1 3 Install an internal SONY CD ROM drive 7 Js Other OPOS eneen ea ieee Aone 8 4 Software Installation c ccc ccceceeceeeeeeeeeeeeaeeeeaeeeeaes 9 4 1 Quick Installations ccicenwosvenniiateacdeoinmocsaeenasetaeverraaackene 9 4 2 Audio Applications Software Installation 10 4 3 Panasonic CD ROM Software Drive Installation 10 4 3 1 CD ROM Device Driver Installation 11 4 3 2 MKE Audio Utility Installation 14 4 4 SONY CD ROM Software cccccccc ccc cce cece eee en es 15 4 4 1 CD ROM Device Driver Installation 15 4 4 2 SONY Audio Utility Installation 18 4 5 MITSUMI CD ROM Software 19 4 5 1 CD ROM Device Driver Installation 19 4 5 2 MITSUMI Audio Utility Installation_________2 Page 2 Stereo Sound amp CD ROM 1 Description This is a 16 bit PC stereo souud combined with CD ROM interface card that lets you system 1 1 add a CD ROM drive and stereo audio to your personal computer Features Programmable sampling rate from 4 KHz to 44 1 KHz Record Compress and Playback at 8 or 16 bit resolution Audio D A and A D conversion 32 levels FIFO 16 bit transfer 64 levels FIFO 8 bit transfer Programmable volume control for
6. 18 bytes dynamic DATA 27344 bvtes used L drive letter Specifies the drive letter to be assigned to the first CD ROM drive Do not assign a letter already used bv an existing drive or Page 18 Stereo Sound amp CD ROM the computer will be unable lo access the CD ROM drive For example you might use O C BIN MSCDEX EXE D MSCD000 L f Normally the CD ROM drive is assigned the next available drive letter 011 the computer after the floppy drives hard drives RAM drives etc Therefore you only need to use this option if it is necessary to assign a drive letter beyond the last letter in use Step 3 Create two sub directory BIN amp DEV under the root directory on your boot hard disk drive C in general Copy both files CDMKE SYS to the subdirectory BIN amp MSCDEX EXE to the subdirectory DEV from the subdirectory CDROM SON Y on the floppy diskette If you are installing the CD ROM drive in a networked system please consult your system manager or system setup for proper drive specifications in Step 1 to Step 3 4 4 2 SONY Audio Utility Installation To install the audio utility von may insert the diskette to the drive that you selected Then change to A or B drive where the floppy diskette is in by entering the following command at the system prompt O C gt A Enter O A gt cd SONYUTIL Enter or 3 C gt B Enter O B gt cd SONYUTIL Enter Then assuming A drive is used do the following O A
7. 3 2 MKE Audio Utility Installation To install the audio utility you may insert the diskette to the drive that you selected Then change to A or B drive where the floppy diskette is in by entering the following command at the system prompt O C gt A Enter O A gt cd MKEAUDIO Enter or O C gt B Enter O B gt cd MKEAUDIO Enter Then assuming A drive 1s used do the following O A MKEAUDI0 gt INSTALL Enter You will be prompted to select the target drive and subdirectory to which the audio utility software will be copy to Afterwards you will be asked to select a software interrupt for the audio utility program You may use the default 60H or select any other on the list Just make sure that the software interrupt selected does not conflict with any other interrupt used by other software programs Upon successful completion of the installation you should find MKECDAPL EXE CDPLAY BAT ESSVOL EXE under the subdirectory that you selected or created on your hard disk To use your CD ROM drive as a regular audio CD player simple execute CDPLAY by entering O C CDROM gt CDPLAY Enter Page 15 Stereo Sound amp CD ROM 44 SONY CD ROM Software The diskette labeled CD ROM Device Driver amp Audio Utility under the subdirectory CDROM SONY contains the SONY CD ROM device driver software and OPTIONALLY the Microsoft MS DOS CD ROM Extension file i e MSCDEX EXE Another subdirectory SONYUTIL contains
8. Drive C in general Page 16 Stereo Sound amp CD ROM O Device drive DEV SLCD SYS B xxx Videvice name O LASTDRIVE drive letter B xxx xxx 1s the I O port address as set on SI of the sound card The default 1s 320H Didevice name specifies device driver name that is used by the Microsoft MS DOS CD ROM extension file as MSCDEX MSCD000 is the commonly used device driver name when none is specified Lastdrilce drive letter Enter the proper drive letter name according to your system configuration For example if you already have 3 hard drives use f If this qualifier is not specified the default used by DOS is e A Step 2 Add the following line to the file AUTOEXEC BAT under your boot hard disk root directory Drive C in general O drive path MSCDEX I D device name M n V L drive letter NOTE The actual MSCDEX EXE command line in the autoexec bat file is not truncated and should be placed entirely 011 one line drive path MSCDEX EXE Specifies the location drive and directory ofthe MSCDEX EXE file The default setting is the BIN director of the boot drive ID device name Specifies the name of the CD ROM drive 8 characters maximum This must be identical to the device name specified in the device driver in the CONFIG SYS file For example O C BIN MSCDEX EXE D MSCD000 Mi n Specifies the number of sector buffers for temporary storage of the most recent di
9. OL EXE CDPLAY BAT under the subdirectory that you selected or created on your hard disk Those drivers enables you to use your CD ROM drive as a regular audio CD player simply execute CDPLAY by entering O CAMTMAUDIO gt CDPLAY Enter Page 24
10. OYSTICK MIDI Connector for PC Speaker In Connector for Panasonic Mitsumi CD ROM Audio in Connector for PC Speaker Out 3 5mm Phone Jack for MIC IN 3 5mm Phone Jack for LINE IN 3 5mm Phone Jack for SPEAKER OUT Connector for SONY CD ROM Audio in Thumb Wheel for VOLUME CONTROL e These connectors are for proprietary external CD ROM drives only Please call your dealer for product availability 1 3 1 Audio Connector Page 4 32 Mitsumi Panasonic 1 4 Switch Stereo Sound amp CD ROM A RIGHT CHANNEL SIGNAL G GROUND B LEFT CHANNEL SIGNAL A RIGHT CHANNEL SIGNAL G GROUND B LEFT CHANNEL SIGNAL S1 CD ROM I O PORT ADDRESS JUJMPERonSWI1 i 2 3 4 5 6 7 8 PORT ADDRESS CD ROM DISABLE ON ON ON ON ON ON ON ON 200H OFF ON ON ON ON ON ON ON 210H OFF ON ON ON ON OFF ON ON 220H OFF ON ON ON OFF ON ON ON 230H OFF ON ON ON OFF OFF ON ON 240H OFF ON ON OFF ON ON ON ON OFF OFF ON ON ON ON ON ON 310H OFF OFF ON ON ON OFF ON ON 320H Factory OFF OFF ON ON OFF ON ON ON Default 330H OFF OFF ON ON OFF OFF ON ON 340H OFF OFF ON OFF ON ON ON ON e Make sure the I O port address selected is not already use by another peripheral device 15 Jumpers JP 1 JP3 JP4 JPS JP6 JOYSTICK port Enable Disable Sound Enable Disable Interrupt Request Selection for Audio I O port address Selection for Audio Direct Memory Access DMA
11. ROM software installation by running SETUP EXE will fail without this file You may obtain this file from your CD ROM drive supplier or if you have DOS version 6 0 or up obtain the file from the operating system Once you secure the MSCDEX EXE you may copy this file to the subdirectory CDROM MITSUMI and then follow instructions to automatically or manually install the CD ROM software 4 5 1 CD ROM Device Driver Installation Put the diskette into your floppy drive change driver to drive A or B At the system prompt change the directory by entering A gt cd CDROM MITSUMI Enter or B gt cd CDROM MITSUMI Enter depending on which drive you use An installation routine SETUP EXE has been provided to assist you installing the software Assuming you are in A enter Page 20 Stereo Sound amp CD ROM A CDROM MITSUMI gt SETUP lEntcr This program will guide you step by step lo setup CD ROM device driver parameters Please refer to the section below to learn more about how to change device driver parameters You may manually install the driver by completing the following steps Step 1 Use any text editor to add the following two lines to the file CONFIG SYS under your boot hard disk root directory Drive C in general ODevice drive DE V MTMCDAS SYS Drdevice name P xxx OLASTDRTVE drive letter IDidevice name specifies device driver name that is used by the Microsoft MS DOS CD ROM extension file a
12. Selection for Audio Page 5 Stereo Sound amp CD ROM 1 5 1 Jumpers Settings JP1 _ GAME GAME JP1 JP JP3 6 1 2 CLOSE 2 3 CLOSE JP3 AUDIO ENABLE AUDIO DISABLE JUMPER SETTING JUMPER SETTING JUMPER SETTING Page 6 2 Stereo Sound amp CD ROM Hardware Installation 2 1 Install the Stereo Sound and CD ROM card Step 1 Turn off the system and ail peripheral devices Step 2 Disconnect the power cord and all peripheral devices from the system Step 3 Remove the system cover and identify an unused 16 bit slot Step 4 Setting the jumpers on the sound card if you would like to change the default settings from the factory Note that makes sure the settings you selected arc correct otherwise we recommend it as the default settings Step 5 Unscrew the slot cover plate plug in the sound card and lighten it with the screw Step 6 Ifyou have speakers or amplifiers plug the cable into J6 jack on the back of the sound card Ifyou do not need to connect a CD ROM device to the sound card disable CD ROM I O port by setting all the jumpers of S1 to ON position Put back the system cover reconnect the system power cord and all peripheral devices Check and make sure all connections are correct before you turn on the svstcm If you need to install a CD ROM drive Please follow the steps below 2 1 1 Install an internal Panasonic CD ROM drive Step 7 Plug one end of t
13. USER MANUAL JANUARY 1994 Version 2 1 E 15 129 Stereo Sound amp CD ROM The information in this document is subject to change without notice FEDERAL COMMUNICATION COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT Warning This equipment has been certified to comply with the limits for Class B computing device pursuant to Subpart J of Part 15 of FCC Rules Only peripherals computer input output devices terminals etc with shielded type interface cables certified to comply with the Class 13 limits may be attached to the computer Operation with non certified peripherals is likely to result in interference to radio and TV reception INSTRUCTIONS TO USER This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instinctions may cause interference to radio and television reception It has been type tested and found to comply with the limits for a Class B computing device Ill accordance with the specification in Subpart J of Part 15 of ICC Rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that will not occurring a particular installation If this equipment does cause interference to radio and television reception which can be determined by turning the equipment offand on the user is encouraged to try to correct the interference by one or more ofthe follow
14. ard with the proper I O address selected See Sec 1 3 4 3 Panasonic CD ROM Software Drive Installation The diskette labeled CD ROM Device Driver amp Audio Utility under the subdirectory CDROM PANASONi contains the Panasonic CD ROM device driver software and OPTIONALLY the Microsoft MS DOS CD ROM Extension file i e MSCDEX EXE Another subdirectory MKEAUDIO contains the MKE audio utilities in order for you to use the CD ROM drive as an audio CD player Please follow steps below to install the driver amp utilities NOTE The file MSCDEX EXE is not furnished unless the card is bundled with a CD ROM drive supplied by us Installing CD ROM software using CDINSTL EXE will fail without this file You may obtain this file from your CD ROM drive supplier or if you have DOS version 6 0 or up obtain the file from the operating system Once you secure the MSCDEX EXE you may copy this file to the subdirectory CDROM PANASONI and then follow instructions manually or using install the CD ROM software Page 1 1 Stereo Sound amp CD ROM 4 3 1 CD ROM Device Driver Installation Put the diskette into your floppy drive change to drive A or B At the system prompt changes the subdirectory by entering A gt cd CDROM PANASONI Enter or B gt cd CDROMVPANASONI Enter depending Oll which drive you use An installation routine CDINSTL EXE has been provided to assist you installing the software Assuming you are in A enter
15. cess the CD ROM drive For example you might use O C BINYMSCDEX EXE D MSCD000 L f Normally the CD ROM drive is assigned the next available drive letter on the computer after the floppy drives hard drives RAM drives etc Therefore you only need to use this option if it is necessary to assign a drive letter beyond the last letter in use Step 3 Create two sub directory BIN amp DEV under the root directory on your boot hard disk drive C in general Copy CDMKJLSYS to the subdirectory BIN and MSCDEX EXE to the subdirectory DEV from the subdirectory CDROM MITSUMI on the floppy diskette If you are installing the CD ROM drive in a networked system please consult your system manager or system setup for proper drive specifications in Step 1 to Step 3 4 5 2 MITSUMI Audio Utility Installation To install the audio utility you may insert the diskette to the drive that you selected Then change to A or B drive where the floppy diskette is in by entering the following command at the system prompt O C gt A lEnter Page 23 Stereo Sound amp CD ROM QO A gt cd MTMAUDIO Enter or O C gt B Enter O B gt cd MTMAUDIO Enter Then assuming A drive is used do the following O A MITMAUDIO gt FINSTALL Enter You will be prompted to select the target drive and subdirectory to which the audio utility software will be copy Upon successful completion of the installation you should find MTMCD EXE ESSV
16. e A or B Assuming drive A 1s used at the system prompt type A install ENTER Follow the on screen instructions and you should be able to install the audio device driver audio application software and CD ROM device driver easily in a few minutes Upon completion of the installation routine please remove all the floppy diskettes from your drive and restart the system All the drivers you just selected will be loaded onto your computer In case of difficulty consult Sees 4 2 4 5 or Audio Applications manual for more information Repeat the quick installation or manually install the driver Page 10 Stereo Sound amp CD ROM 4 2 Audio Applications Software Installation The audio drivers and application software of the PC stereo sound are included in the diskette 1 and diskette 2 Please refer to the user manual Audio Applications that comes with this package for installing the Audio drivers and application software The following sections show you how to install CD ROM device driver software and utility software for playing music CD using your CD ROM drive You need to go through the following sections to install the CD ROM software only if you are installing a new CD ROM drive If you are simply connecting an existing CD ROM drive to our sound card with pre installed device driver software skip the following sections You should be able to use your existing CD ROM drive after it is physically connected to our c
17. e Unplug the cable of the PC speaker from the PC speaker connector on the system Motherboard e Connect the cable of the PC speaker to J3 on the sound card Nore If you are currently using the PC speaker for the sound card and need to change to external speaker make sure that the cable of the PC speaker is disconnected from J3 and reconnected to the motherboard Page 9 Stereo Sound amp CD ROM 4 Software Installation Before proceeding with audio and CD ROM software installation please check the software diskettes that come with the card CD ROM Software one diskette labeled CD ROM Devicc Driver amp Audio Utility It includes device drivers and CD audio playback utilities for different types of CD ROM drive It also contains our easy to use general installation routine Audio Applications Software 2 diskettes disk 1 disk 2 All the audio device drivers and applications for Windows are included in these two diskettes Section 4 1 describes how to use our easy to use installation routine to install CD ROM drive and audio device drivers Sections 4 2 4 3 4A 4 5 contain information that would allow you to manually install the different type of CD ROM device driver or to optimize the performance ofthe CD ROM drive 4 1 Quick Installation The diskette labeled CD ROM Device Driver amp Audio Utility contains a program named INSTALL EXE under the root directory Please insert the diskette into the driv
18. ears Expanded memory not present or not usable I V Instructs the computer to display a summary of RAM allocation and expanded memory usage at booting For Example specifying O C CDROM MSCDEX EXE D MSCD000 V will cause the computer to display memory information in the following format 5556864 bytes free memory 0 bytes expanded memory 12752 bytes CODE 1712 bytes static DATA 12618 bytes dynamic DATA 27344 bytes used L drive letter Specifies the drive letter to be assigned to the first CD ROM drive Do not assign a letter already used by an existing drive or the computer will be unable to access the CD ROM drive For example you might use O C CDROM MSCDEX EXE D MSCD000 L f Normally the CD ROM drive is assigned the next available drive letter on the computer after the floppy drives hard drives RAM drives etc Therefore you only need to use this option 1fit is necessary to assign a drive letter beyond the last letter in use Step 3 Create a sub directory CDROM under the root directory on your boot hard disk drive C in general Copy both files Page 14 Stereo Sound amp CD ROM CDMKE SYS amp MSCDEX EXE from the subdirectory CDROM PANASONI 011 the floppy diskette to the sub directory CDROM just created on your boot hard disk If you are installing the CD ROM drive in a networked system please consult your system manager or system setup for proper drive specifications in Step 1 to Step 3 4
19. he 40 pin flat ribbon cable into CN5 on the sound card Pin 1 of the ribbon cable is usually denoted with a red stripe Step 8 Plug the other end of the 40 pin ribbon cable into the back of the CD ROM drive and connect the power plug from your system power into the CD ROM drive power connector Step 9 Connect J2 on the sound card and the Audio output at the back of the CD ROM drive Make sure pin 1 of J2 is connected to the left most pin of the CD ROM Audio output Page 7 Stereo Sound amp CD ROM NOTE A standard Audio cable for the Panasonic drive has only 3 pins Pin 4 of J2 thus will not used Step 10 Put back the system cover reconnect the system power cord and all peripheral devices Check and make sure all connections are correct before you turn on the system 2 1 2 Install an internal Mitsumi CD ROM drive Step 7 Plug one end of the 40 pin flat ribbon cable into CN2 on the sound card Pin 1 of the ribbon cable is usually denoted with a red stripe Step 8 Plug the other end of the 40 pin ribbon cable into the back of the CD ROM drive and connect the power plug from your system power into the CD ROM drive power connector Step 9 Connect J2 on the sound card and the Audio output at the back of the CD ROM drive Make sure pin of J2 is connected to the left most pin of the CD ROM Audio output Step 10 Put back the system cover reconnect the system power cord and all peripheral devices Check and make sure al
20. ing measures Reorient the receiving antenna i Change the orientation ofthe computer i Move the computer away from the receiver Plug the computer into a different outlet so the computer and receiver are on different branch circuits Ifthese attempts are unsuccessful install one or all ofthe following devises 1 Line isolation transformers 2 Line filters 3 Electro magnetic shielding If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington DC 20402 Stock No 004 000 00345 4 All brands and trademarks are registered by their respective companies Printed in Taiwan Page 1 Stereo Sound amp CD ROM Table of Contents k Descriptio icesnrnse cane cadecaaeaidecsoacnonte aeusmabe duces 2 LI Features 2 E2 Card Howe cor o a E ee ia et 3 1 3 Connectors__ ___W9 _ OF 1 3 1 Audio Coimcctor _________ 4 14 Switch sss 1S 4PM ONS ero a E R 4 1 5 1 Jumpers Settings csc Faster oaa aaae es Gh eee eae oe dO 2 Hardware Installation 000 cc cece ccc ccc ccccccccececcccceeeecess 6 2 1 Install the Stereo Sound and CD ROM card______6 2 1 1 Install an
21. l connections are correct before you turn on the system 2 1 3 Install an internal SONY CD ROM drive Step 7 Plug one end of the 34 pin flat ribbon cable into CN1 on the sound card Pin 1 of the ribbon cable is usually denoted with a red stripe Step 8 Plug the other end of the 34 pin ribbon cable into the back of the CD ROM drive and connect the power plug from your system power into the CD ROM drive power connector Step 9 Connect J7 on the sound card and the Audio output at the back of the CD ROM drive Make sure pin 1 of J7 is connected to the left most of the CD ROM Audio output Step 10 Put back the system cover reconnect the system power cord and all peripheral devices Check and make sure all connections are correct before you turn on the system Page 8 Stereo Sound amp CD ROM 3 Other Options If you would like to redirect the audio for the PC speaker to the external speakers attached to the sound card please follow the steps below e Unplug the cable of the PC speaker from the PC speaker connector on the system Motherboard e Using the cable provided connect J1 and the PC speaker connector on the system motherboard There is no guarantee that this option works for all motherboards If you run into difficulty please consult your system manager or the manufacturer of your system motherboard In case you need to use the PC speaker as the only speaker for the sound card please follow the steps below
22. s MSCDEX MSCDO000 is the commonlv used device driver name when none 1s specified P Xxx xxx is the I O port address as set on S1 of the sound card The default 1s 320H Lastdnve 1 n vc letter Enter the proper drive letter name according to your system configuration For example if you already have 3 hard drives use f If this qualifier is not specified the default used by DOS 1s V Step 2 Add the following line to the file AUTOEXEC BAT under your boot hard disk root directory Drive C in general 3 drive 1 path MSCDEX D device name M n E V IL drive letter NOTE The actual MSCDEX EXE command line in the autoexec bat file is not truncated and should be placed entirely on one line drive path MSCDEX EXE Page 21 Stereo Sound amp CD ROM Specifies the location drive and directory of the MSCDEXEXE file The default setting is the BIN directory ofthe boot drive Didevice name Specifies the name of the CD ROM drive 8 characters maximum This must be identical to the device name specified in the device driver in the CONFIG SYS file For example O C BIN MSCDEX EXE DrMSCDOOO M n Specifies the number of sector buffers for temporary storage of the most recent disc data For example to specify ten sector buffers you would use O C BIN MSCDEX EXE D MSCD000 M 10 The installation program will set this value to 10 The default value is 4 NOTE The greater this value the be
23. sc data For example to specify ten sector buffers you would use O C BIN MSCDEX EXE D MSCD000 M 10 Page 17 Stereo Sound amp CD ROM The installation program will set this value to 10 The default value is 4 NOTE The greater this value the better the CD ROM drive will perform However each buffer uses about 2K of memory and specifying too many buffers may slow down computer operation or interfere with other programs which have large memory usage requirements Using expanded memory sec the E option in this section or loading MSCDEX EXE into high memory refer to your MS DOS Users Manual or Memory Manager Users Manual may allow you to specify a larger number of buffers to enhance CD ROM performance and operate programs with large memory usage requirements simultaneously E Instructs the computer to use expanded memory if available For example O C BIN MSCDEX EXE D MSCD000 E Note that vou must first load an expanded memory driver before using this option Ifno expanded memory driver is load the following error message appears Expanded memory not present or not usable IJ Instincts the computer to display a summan of RAM allocation and expanded memory usage at booting For Example specifying O C BIN MSCDEX EXE D MSCD000 V will cause the computer to display memory information in the following format 5556864 bytes free memory 0 bytes expanded memory 12752 bytes CODE 1712 bytes static DATA 126
24. the SONY audio utilities in order for you to use the CD ROM drive as an audio CD player Please follow steps below to install the driver amp utilities NOTE The file MSCDEX EXE is not furnished unless the card is bundled with a CD ROM drive supplied by us Automatic CD ROM software installation by running SETUP EXE will fail without this file You may obtain this file from your CD ROM drive supplier or 1f you have DOS version 6 0 or up obtain the file from the operating system Once you secure the MSCDEX EXE you may copy this file to the subdirectory CDROM SONY and then follow instructions to automatically or manually install the CD ROM software 441 CD ROM Device Driver Installation Put the diskette into your floppy drive change driver to drive A or B At the system prompt change the directory by entering A gt cd CDROM SONY Enter or B gt cd CDROM SONY Enter depending on which drive you use An installation routine SETUP EXE has been provided to assist you installing the software Assuming you are in A enter A CDROM SONY gt SETUP Enter This program will guide you step by step to setup CD ROM device driver parameters Please refer to the section below to learn more about how to change device driver parameters You may manually install the driver by completing the following steps Step 1 Use any text editor to add the following two lines to the file CONFIG SYS under your boot hard disk root directory
25. tter the CD ROM drive will perform However each buffer uses about 2K of memory and specifying too many buffers may slow down computer operation or interfere with other programs which have large memory usage requirements Using expanded memory see the E option in this section or loading MSCDEX EXE into high memory refer to your MS DOS Users Manual or Memory Manager Users Manual may allow you to specify a larger number of buffers to enhance CD ROM performance and operate programs with large memory usage requirements simultaneously VE Instructs the computer to use expanded memory if available For example O C BIN MSCDEXEXE D MSCD000 E Note that you must first load an expanded memory driver before using this option If no expanded memory driver is load the following error message appears Expanded memory not present or not usable VI Page 22 Stereo Sound amp CD ROM Instructs the computer to display a summary of RAM allocation and expanded memory usage at booting For Example specifying O C BIN MSCDEXEXE D MSCD 00 V will cause the computer to display memory information in the following format 5556864 bytes free memory 0 bytes expanded memory 12752 bytes CODE 1712 bytes static DATA 12618 bytes dynamic DATA 27344 bytes used Lulrive letter Specifies the drive letter to be assigned to the first CD ROM drive Do not assign a letter already used by an existing drive or the computer will be unable to ac
Download Pdf Manuals
Related Search