USER'S MANUAL CURRENCY COUNTER NC 600B
Contents
1. 10 to enter the setting of banknote density The sensitivity of banknote density is adjustable by continuously pressing the 10 key and the sensitivity can be changed from dE1 dE2 dE3 dE4 dES dE6 dE7 dE8 dE9 dE10 dE11 dE12 dE13 dE14 dE15 dE16 the default setting is dE4 gt Please note 1 For the sensitivity of counterfeit detection the smaller the number the higher the sensitivity 9 2 If mis alarm frequently occurred please decrease the sensitivity of counterfeit detection i e increase the number if the machine often fails to report the dubious notes please increase the sensitivity i e decrease the number 2 5 Memory of the last setting The currency counter has the function of automatically saving the parameters of the last setting When each function and its parameters have been set press the START STOP key and the present setting is saved The machine will be working under the new setting after being turned on next time 3 Error Codes and their elimination 3 1 Error codes displayed after the self test of the machine their meanings and their elimination 3 2 When the machine stops upon the detection of dubious banknote the error codes and their elimination are as follows Error Code Error Position Elimination FE1 Feeding Sensor FE2 Left Counting Sensor Gicae ies deena FE3 Right Counting Sensor i an2. 1200 requirement notes per minute and the UV detection mode Operation 2 1 Turning on the Machines 2 2 General Operation 2 1 1 Please ensure that the power supply you 2 2 1 Front panel operation are using is with the same parameter as the ones on the back of the machine 2 1 2 The machine will proceed automatic checkout for two seconds If the machine is under normal condition the count display shows 0 Put the bills on the input hopper the machine will automatically start to count gt Please note 1 When such code signals as FE X are displayed during the process of turning on 2 3 1 2 3 Batch keypad The three batch keys are to set the batch number the user desires And thel CLEAR key is to clear the batch number on the parameter batch display Main Function keys A Uv to discriminate the suspected banknote through UV detection during the process of counting B SPEED to set the counting speed C ADD to accumulate all the effective value on the count display D MUL to switch ON and OFF the manual counting function E START STOP to withdraw from the state of parameter presetting to clear the count display to 0 to stop the machine at any time during the counting process and to start the manual counting Auxiliary function keys Press 100 on the batch keypad twice 1 10 twice and 1 twice the batch parameter display s
3. Uv key the indicator light is turned off and the machine counts the banknotes without counterfeit detection v Press the Uv key again the counterfeit indicator light is on showing the function of counterfeit detection through UV is enabled gt Please note 1 It is suggested that the first note of the counting pile should be a 70 new bill without pollution so as to be considered as the standard for auto identification 2 The sensitivity of UV counterfeit detection can be adjusted or even turn off For the details of 6 operation please refer to Section 2 4 2 3 2 Speed adjustment The machine gives the user 4 speed levels to choose from including 600pcs m 900pcs m 1200pcs m and 1500pcs m To choose the desired speed press the function key SPEED l Generally to make the machine work under the best condition 900pcs m is recommended as the most suitable speed 2 3 3 Accumulation of effective counting value Press the ADD key the indicator light above is on and the count display will show the total of all the effective counting value i e except for the dubious bill which is not counted into the effective value since the machine is turned on And the machine will continue to count from the total value 2 3 4 Batch presetting The batch presetting can be achieved by directly pressing the keys on the batch keypad When the batch number is reached the machine will stop for the user to take out t
4. the FE4 Stacker Sensor machine again FES Speed Sensor FE6 UV Sensor Error Sanh b Code Meaning Elimination Take out the half note and press EHX half note START STOP to continue the counting Check the notes mis alarm could occur if the notes are very old EP 2 SULS ous press START STOP to continue the counting Take out the banknotes on the stacker put on the input hopper Eras Sopot and press START STOP to count the bills again notes of Take out the shorter longer note dd X different and press START STOP to denomination continue the counting Take out the banknotes on the stacker put on the input hopper ines sana and press START STOP to count the bills again Take out and check the suspected Su X UY ushers note and press START STOP to note continue the counting 10 gt Please note 1 The number behind the error code shows the 11 credibility of the detection of the suspected notes The bigger the number the higher the credibility 2 When the machine stops and alarms when counting the first three banknotes they should be taken out of the stacker put back to the input hopper and count again by pressing the START STOP 3 When the batch display shows EC the machine will not continue the present counting unless all the banknotes have been taken out from the output stacker If any of the other error codes are shown on the batch
5. GeEMs vS USER S MANUAL CURRENCY COUNTER NC 600B Please read this instruction manual carefully before the operation gt Notice a Reliable grounding is required for the socket connected with the machine b The voltage of the power supply connected with the machine should be within the stipulated range c Please turn off the machine and pull out the plug when opening the back cover of the machine or cleaning the dust 1 General Introduction The following specifications are for your better understanding of the machine gt gt Counting speed 600pcs m 900pcs m 1200pcs m and 1500pcs m Countable paper size 50 X 110 95 X 185 mm thickness 0 07 0 2mm Detection of suspected notes half notes double notes chain notes UV suspected notes Display modes four digit LED count display three digit LED parameter batch display Preset Batch Number three digits batch keypad 100 10 and 1 the machine and counting bills please gt Input Hopper Capacity adjust them with reference to 3 1 Approx 200 bills 350 bills with extension clips 2 With memory chips installed the gt Output Stacker Capacity Approx 200 bills parameter setting of the machine is up to gt Dimensions 265 X 235 X 190 mm your own choice The default gt Net weight 6KGS configuration are gt Power supply Auto counting auto recognition of 220V 50HZ or I110V 60HZ as per user s different width counting speed
6. display and on the condition that the number shown on the count display is not 0 press the START STOP key to continue the present counting process 4 Repair and Maintenance Give the machine everyday cleaning and a thorough cleaning to the surface of the sensors and the parts inside every week Info www gemsys eu www gemsys europe com 12
7. he bills and so that it can continue the batch operation T gt Please note 1 Continuous batch counting is only applicable under the state of auto counting 2 The preset batch under manual counting can only do the batch counting for one time 2 3 5 Batch number clearance Press CLEAR key to clear the preset batch number on the batch parameter display And the machine withdraws from the batching state 2 4 Setting the auxiliary functions Press 100 on the batch keypad twice 10 twice and 1 twice the batch parameter display shows 222 and then press once the key till the batch parameter display shows Set the machine enters the auxiliary function setting 2 4 1 Press UV to enter the setting of UV detection The sensitivity of UV detection is adjustable by continuously pressing the 1 key and the sensitivity can be adjusted from Sul Su2 Su3 Su4 Su5 Su6 Su7 Su8 Su9 Sul0 Sull Sul2 Sul3 Sul4 Sul5 to Sul6 the default setting is Su4 2 4 2 Press 1 to enter the setting of width difference of the banknotes The sensitivity of width difference detection is adjustable by continuously pressing the 1 key The sensitivity is adjustable from ddl dd2 dd3 dd4 dd5 dd6 and dd7 the default setting is dd4 When the width difference between the bills is detected to be over the set parameter the machine alarms and stops counting 2 4 3 Press
8. hows 222 and then press once the 4 1 key till the batch parameter display shows Set the machine enters the auxiliary function setting UV z to adjust the sensitivity of UV detection or to turn off the UV detection by setting the parameter to 0 1 to set the sensitivity of paper width 10 to adjust the sensitivity of paper density 2 2 2 How to position the feeding chink adjusting 1 2 knob with a coin Turn the coin clockwise to to enlarge the feeding chink counter clockwise to to decrease the feeding chink When the bills cannot be counted smoothly enlarge the feeding chink to when the machine stops with signals like ED EC displayed decrease the feeding chink to Please note don t rotate the adjusting knob to a large degree and only the inching movement is applicable 2 2 3 How to adjust the paper guide 1 The width of the paper guide should be in 5 accordance with that of the bills that the machine is to count 2 When there s width difference between the bills please adjust the paper guide to suit the present width of the bills so as to avoid mis alarm 2 3 Setting the main functions 2 3 1 Counterfeit detection v After the self test for two seconds the machine proves to be in the normal condition and the indicator light for UV is on v Press the
Download Pdf Manuals
Related Search