Operating Instructions DIGAP-3A-... English Digital
Contents
1. Operating Instructions D GAP 3A Valid for software version SW2 2 English Digital Proportional Amplifier For valves with DIN43650A ISO4400 connection DIGAP 3A UKS IKS C DIGAP 3A US IS Cable connection with NPN switching output Plug connection M12x1 BIBUS Austria Eduard Klinger Strasse 12 A 3423 St Andr W rdern Tel 43 2242 33388 Fax 43 2242 3338810 Internet WWW bibus at Mail INfo bibus at Read these operating instructions carefully before installing and operating this product Operation by technical staff only Pre Conditions for the use of this product To ensure the safe and secure use of this product it should only be used according to specification and the general advice must always be followed e Always follow the stated critical and limiting values according to specification such as forces temperatures and voltage Consider ambient temperature and moisture Consider local laws and regulations Use this product only in the original and supplied shape you must not carry out any modifications Remove all packaging and transit support Stipulations of use Protection Category IP 65 The Protection Category and the type test must not be applied to all applications The correct fitting of the socket cables wiring and other parts has to be approved and checked by user and operator Temperature Always bear in mind that the part could be heated by neighbouring appliances Also bear in m2. 0 9 disbanding 1000 steps factory setting 0 no voltage at the valve Warning If you choose this setting mode the valve will be under the set current Be careful when changing this setting an incorrect adjustment may result in an accident Limit max current 0 100 display 0 9 disbanding 1000 steps factory setting 75 Warning If you choose this setting mode the valve will be under the set current Be careful when changing this of setting an incorrect setting may result in an accident Chopper frequency 100 500 Hz display 0 5 disbanding 500 steps factory setting 150 Hz En u Page 2 of 4 Operating Instructions D GAP 3A English Valid for software version SW2 2 UKS IKS Dimension and installation information en 34 Position I 90 Position 2 180 Position Dichtung Sealing braun brown braun brown el m gr n green i yell geb Ye 0 10 VDC gt wei white E p Schirm shield DE Schirm shield PE oe mit Potentiometer Anschlu an SPS PLC Control Installation PLC Control no possibility of potentiometer installation IKS braun brown P A oe wire colours yell m gelb yellow 0 4 20 mA brown VDC white VDC GND eh whe yellow 0 10V 0 20mA input a green 10V output auxiliary voltage grey switching output NPN max 200mA Schirm shield PE shield PE
3. earth PLC Control Symbolic load switching output Page 3 of 4 Operating Instructions D GAP 3A English Valid for software version SW2 2 Dimension and installation information 1 IC e Analog IH 3 YDCE GWO 4 10VDC OUT Position 1 907 Faositlon 2 180 Position 0 ca 39 4 Dichtung Seallrg Anschlu mit Potentiometer Anschlu an SPS Potentiometer Control PLC Control Installation PLC Control no possibility of potentiometer installation plag configuration 1 brown VDC 2 white Analogue input 3 blue VDC GND 4 black 10 VDC OUT 5 yellow green PE earth Please note that the wire colours in the bracket are not valid for every supplier Bitte beachten Sie dass die in Klammer angefthrten Anschlu an SPS Aderfarben nicht fur alle Hersteller gelten PLC Control Page 4 of 4
4. in 40210 NOTE The switching points are out of function at the design DIGAP 3A US and DIGAP 3A IS Manipulation Set adjustments DISPLAY tol MENU SET WERT VALUE Push SET s to change into the setting mode FUNCTION Choose the setting mode with up and down Push again SET s to see the data of the chosen function AB jel iel AUF Change setting with up and down DOWN ee l UP Keep SET s pushed for 2 sec to save settings or push SET s shortly to get the s u previous setting clavate After 10 sec the amplifier is switching back to the normal mode Adjustment r Rise time 0 10 sec display 0 9 disbanding 100 steps factory setting 1 sec Drop out time 0 10 sec display 0 9 disbanding 100 steps factory setting 1 sec Setting point minimum 0 100 display 0 9 disbanding 1000 steps factory setting OV 0 Setting adjust the potentiometer to your chosen minimum point or put the chosen minimum setting onto the tL port 0 10V Now set the desired current at the DIGAP Notice this setting can also be below the limit min current Setting point maximum 0 100 display 0 9 disbanding 1000 steps factory setting 10V 70 Setting adjust the potentiometer to your chosen maximum point or put the chosen maximal setting onto the port 0 10V Now set the desired current at the DIGAP Notice this setting can also be over the limit max current Limit min current 0 100 display
5. ind that approved temperatures could burn and cause harm to human beings Technical data Supply 11 30VDC Residual ripple 10 Output current up to 2 5A 2500mA Output power 60 W Chopper frequency 100 500 Hz Ramps up down up to 10 separately adjustable Temperature from 25 to max 70 C Power consumption Connector standard Protection class System supply 15mA 24VDC DINA43650A ISO4400 revolves 90 max 180 IP65 properly assembled 4 5 poll socket M12x1 ISO DIN or 2m PVC cable 5x0 5 Display 7 segment LED display functions amp values Adjustment programmable by keys inside housing Weight xKS 280g including cable xS 72g Tariff 90269090 EMV according to EN 61000 6 3 2001 10 EN 61000 6 2 2001 10 Accessories Angle plug ELWIKA 5012 PG7 required only for model US IS Straight plug ELKA 5012 PG7 required only for model US IS Sealing GDM3 7 Page 1 of 4 Operating Instructions D GAP 3A English Valid for software version SW2 2 LED Symbols Symbols normal mode Symbols setting mode Symbols Set point reached r Rise time upward chute Bg data n Downward regulating l Dropant time downward chute Graphic chart m Upwards regulating H y Chopper frequency i Minimum reached Offset 1 Min current Offset a A Maximum reached current limiting 9 Max current L OV setting point I 10V setting point i Switching point OFF Switching point ON
Download Pdf Manuals
Related Search