User's Guide
Contents
1. throughput E Automatic configuration through the PCI BIOS Programmable PCI burst size M Provides 32 bit Bus Mastering data transfers M Diagnostic LINK Active LEDs for quick troubleshooting MSupport 32K 64K EPROMSs for remote BootROM MSupport flow control Option Support Wake On LAN function Option Support ACPI PCI power management LED Indicators The adapter provides one LED indicators for monitoring network conditions This section describes the function of LED Refer to Figure 2 Figure 2 LED indicator 100 10 100 10 Link Active Active Specifications Standards i4 5 si4 aes IEEE802 3 802 3U Bus Types PCI Bus Revision2 1 Network Interface 1O0Base T and 100Baes TX Full Duplex 20Mbps and 200Mbps I O Address Automatically determined by PCI BIOS Interrupt IRO INTA ON PCI slot pin assignment Boot ROM Size 3 9 4K byte EPROM Bus Access Method Aaster Temperature 0 C to 55 C Std Operating 32 F to 104 F H midity srities 10 to 90 non Condensing Dimensions 4 72 x1 54 Non Bracket 120mmx39mm Hardware Installation The section describes the procedure for installing the adapter Follow the steps listed below to install the PCI LAN adapter 1 Power off your PC and remove its cover 2 Select an empty PCI slot and insert the adapter Note If your card support Wake On LAN Please con2. This setup program can configuration and diagnostics PCI adapters It is in the root directory of the Driver Diskette that comes with the package It is used to set the PCI adapter s parameter such as Operating mode Media type Full duplex Boot ROM address and Wake On LAN statrs on board test etc Run the setup program Insert the driver diskette into floppy driver of the host PC Then at the DOS prompt type the following and press Enter A gt 9939D lt Enter gt Boot ROM Installation The optional BootRoM allows you to connect a workstation without disk driver to your network System Installation procedure 1 Plug the BootROM into the BootROM socket 2 Run the program to change the configuration to enable the BootROM at available address 3 Refer to your Network Operating System installation guide for detail Make image file If you need BootROM please call your dealer for assistance When installing the BootROM into the socket Please make sure that the BootROM IC mark is in the same direction as the other ICs on the adapter Also see to it that all the IC legs are in the right holes of the Socket Supported Network Drivers E Novell Netware v3 12 4 0 5 0 included Client Server drivers E Microsoft Windows NT V 3 5X V4 0 E Microsoft Windows 95 95 OSR2 98 E Microsoft windows 2000 E Packet Drivers for FTP TCP IP NCSA TCP IP All products or brand names mentioned are trademarks or registered trademarks of the
3. ir respective companies Appendix 10Base T Twisted pair Cable The RJ 45 connector used on 10Base T Ethernet networks is the 8 pin RJ 45 modular phone jack The cable used is 0 4 0 6mm round wire UTP or STP wire cable similar to that used for ordinary telephone voice transmission Pin Number Assignment 1 Transmit Data 2 Transmit Data 3 Receive Data 6 Receive Data 4 5 7 8 Received 12345678 10Base T Phone Jack connector SKU06512 Fast Ethernet 100Base TX PCI Adapter User s Guide The 100Base TX PCI Ethernet Adapter is a 32 bit 10 100Mbps Fast Ethernet Adapter It supports IEEE 802 3 10Base T IEEE 802 3u 100Base TX and combines two transmission rate 10 100 on one RJ 45 connector This Adapter supports bus mastering architecture and both transmission rate offer Full Duplex function to connect to Switching Hub Extensive driver support for commonly used network operating systems is available Unpacking Information This product package should contain One 10 100Mbps Fast Ethernet Adapter One 3 5 Setup amp Drivers Diskette Disk This User s Guide m Product Description The 100Base TX has one RJ 45 connector and one LED indicator as shown in Figure land Figurt 2 Figure 1 PCI Fast Ethernet Adapter EComplete compatibility with the 10Base TX and 100base TX standards E Automatically senses media type MFull Duplex Etherne 4 20Mbps and 200Mbps
4. nect the cable to the mother board And read the manual of the mother board to know about how to set up the Wake On LAN function 3 Connect your adapter to the network using RJ 45 4 Power on the PC 5 Rim doagmpstocs the program to check the adapter of hardware configuration See the section on Diagnostic setup program for more information 6 Installation the software driver Refer to the Software Drivers section Diagnostics Setup Program Before running the program you Should remove network drivers first of the system could be hung up
Download Pdf Manuals
Related Search