User Manual
Contents
1. Indicator Status Description Constantly The power is connected and switched on on Power off The power is not connected or the device fails to function Flashing The device is functioning Run Off The device fails to function Constantly The connection is established and the IP address is on allocated Flashing Data is being transmitted The following problems may be present Internet e The system is not powered on off e ADSL connection is not established e The IP or PPP session is terminated due to a reason other than Idle Timeout e ADSL is in the bridge mode only Constantly ADSL connection is established on DSL ae Flashing ADSL connection is being established Off ADSL connection is not established Indicator Status Description Constantly LAN connection is established on len Flashing Data is being transmitted Off LAN connection is not established On WLAN RF is switched on WLAN Flashing Data is being transmitted Off WLAN RF is switched off On WPS is switched on and functioning The indicator will turn off in five minutes Slowly Negotiation is in process through WPS WPS flahsing Fast flashing WLAN terminal s WPS access encountered an error Off Device failure or not in use On USB storage device connected USB1 USB2 Flashing sea USB storage devices or performing data Off Non USB storage device connected Notes2. The quantity of USB indicators ranges from 0 to 2 depending on the actual product model 2 3 Introduction to Sockets and Buttons e Sockets and buttons on the rear panel of H108L The sockets and buttons on the rear panel of H108L are as follows oR E a FE AWA Power Reset LANA LAN2 LAN3 The description of sockets and buttons on the rear panel of H108L is as follows Name Function Description Connects to standard power adapter to obtain DC Power Power socket power supply When the device is operating keep pressing the Reset Reset button button for more than 5 seconds to restore the default settings Then the system restarts automatically 4 Name Function Description LAN1 LAN4 Ethernet Connects to PC s network adapter or other network ports device via RJ 45 cable DSL DSL socket Connects to ADSL cable or splitter via RJ 11 telephone line e Sockets and buttons on the side panel of H108L Socket and buttons on the side panel of H108L are as follows On Off WLAN WPS ly Joo The description of sockets and buttons on the side panel of H108L is as follows Name Function Description On Off Power switch Switches on or off power supply keep pressing the button for more than 5 seconds WLAN AAN SERIEN to switche on or off WLAN RF WPS wes access Switches on or off
3. WPS access switch USB1 USB2 USB port Connects USB storage devices Notes The quantity of USB ports ranges from 0 to 2 depending on the actual product model 3 Instal lation 3 1 Installing Device Appropriate space for heat dissipation is required to prevent the device from overheating Do not place the device close to heat sources or under direct sunlight Do not block the heat dis sipation opening 1 Placement Place the device at a place where its surface is plane and where there will be less obstacles when communicating with the wireless terminals to ensure the best signal strength It is recommended to use wireless terminals in the room where H108L is placed or the immediate room 2 H108L adopts the ADSL uplink mode to get connected to the Internet It is recommended to connect the device as the approach shown in the following figure 5 ADSL Connection 3 If a telephone is required to be installed before the splitter make sure to connect a voice filter properly to the Line socket of the splitter and then connect the telephone to the filter Connect other sockets as the above figure Notes Please use the power adapter delivered with the device Otherwise the device might be damaged 3 2 Setting Preparations 3 2 1 Checking PC Settings It is recommended to turn off VPN and firewalls on your PC The following uses Microsoft IE as an example to
4. a long period of time unplug the power cord Watch out the children especially when they are using the device without any custody If any abnormal phenomenon appear on this product such as smoke weird sound and or smell unplug the power adapter Do not use the device in the thunderstorm For Service Do not attempt to disassemble repair or open this product which will cause you lose the war ranty services Contact qualified service personnel in case of problems especially under the following conditions The power socket or cable is damaged Liquid is splashed into the product The product is exposed to rain or water The product does not work normally when the operating instructions are followed The product is dropped or struck causing the product damaged 2 Introduction 2 1 Product Overview Thank you for using ZXV10 H108L hereafter referred to as H108L Home Gateway H108L can serve as the center of a home network where various devices can share the Internet connection to provide data communication and entertainment services The delivery of services needs the support of local operators contact local operators for more information 2 2 Introduction to Indicators Indicators on the front panel are used to show the status of H108L which is shown in the figure below USB2 USB1 WPS WLAN LAN4 LANS LAN2 LAN1 DSL Internet Run Power Indicators on the front panel are described in the table below
5. ZTEDH ZXV10 H108L Home Gateway User Manual Version 1 0 ZTE CORPORATION LEGAL INFORMATION Copyright 2010 ZTE CORPORATION The contents of this document are protected by copyright laws and international treaties Any repro duction or distribution of this document or any portion of this document in any form by any means without the prior written consent of ZTE CORPORATION is prohibited Additionally the contents of this document are protected by contractual confidentiality obligations All company brand and product names are trade or service marks or registered trade or service marks of ZTE CORPORATION or of their respective owners This document is provided as is and all express implied or statutory warranties representations or conditions are disclaimed including without limitation any implied warranty of merchantability fitness for a particular purpose title or non infringement ZTE CORPORATION and its licensors shall not be liable for damages resulting from the use of or reliance on the information contained herein ZTE CORPORATION or its licensors may have current or pending intellectual property rights or appli cations covering the subject matter of this document Except as expressly provided in any written license between ZTE CORPORATION and its licensee the user of this document shall not acquire any license to the subject matter herein ZTE CORPORATION reserves the right to upgrade or make techn
6. d in route mode only It cannot be configured in bridge mode Enable VLAN Enable disable VLAN configuration VLAN ID and 802 1p are used to define to which VLAN the device belongs as well as the priority VLAN ID VLAN ID of data packets at WAN interface The value ranges from 1 to 4094 802 1p Deals with priority suitable for multiple WAN connections only The value ranges from 0 to 7 The default value is 0 which indicates no priority set The greater the value is the higher the priority is VPI VCI VPI VCI Virtual Path Channel Identifier identifies virtual path and virtual channel of a link In the case of first time configuration select Create and then configure the VPI VCI values Otherwise select a previously used VPI VCI values from the drop down list New VPI VCI Configures VPI VCI values which range from 0 to 255 and from 0 to 65535 respectively Both of which are provided by the ISP Encapsulation Type The protocol encryption type which supports LLC and VCMUX Configuration of ATM QoS which imposes restrictions on Service Type uplink traffic Four types are available CBR RT VBR nRT VBR and UBR Username and password for WAN connection Username Password authentication Both of which are provided by the ISP Authentication Type Authentication protocol type Options Auto PAP and CHAP The value is Auto by default Connection Trigger Connection trigge
7. ding to the previous solutions If a telephone is installed before the splitter please make sure that the splitter is correctly installed WLAN cannot be connected e Make sure that the WLAN RF is switched on and the WLAN indicator is on e Check whether the wireless network card is correctly configured e Check whether the network name encryption mode and encryption key stored in the PC are consistent with the settings of H108L PC is unable to access the network e Check whether the IP address of H108L 192 168 1 1 by default can be pinged successfully from the PC If cann ot please check the Ethernet connection and whether the indicator status is normal e Itis recommended to set the IP address and DNS server address to be obtained automatically e Itis recommended to disable all running firewall or secu rity software e Disable the proxy server of the Web browser e Check whether the indicator status is normal 13 6 Specification Physical Specification Size Excluding bracket 200mm 168mm 36mm length width height Including bracket 200mm 168mm 75mm length width height Weight Excluding bracket 300g excluding power adapter Including bracket 360g excluding power adapter Electric Specification Non USB Scenario Power supply Input 220V AC 50Hz output 12V AC 750mA Power 9W USB Scenario Power supply Input 220V AC 50Hz output 12V AC 1A Power 12W Enviro
8. f IE browser and press Enter Then the Login page shown in the following figure pops up Please login to continue Username L Password Login 2 Input username and password default username and password are admin and admin and click Login to enter H108L page 3 Click Logout at the top right corner of corresponding page to exit 4 2 Network Configuration 4 2 1 Creating WAN Connection 1 Select Network WAN WAN Connection to open the WAN Connection page as shown in the figure below Connection Name Create WAN Connection New Connection Name Enable NAT Enable VLAN VLAN ID 802 1p VPIVCI New VPIVCI Encapsulation Type iL Service Type Username Password Authentication Type Auto Connection Trigger Always On Idle Timeout Create Cancel 2 Set the parameters according to the description below Parameter Name Description The default value is Create WAN Connection Users Connection Name can select created network connections from the drop down menu Type of connection Select WAN connection type from five options including PPPoE PPPOA Static need the operator to provide IP address DHCP and Bridge Connection The default value is PPPoE Type New Connection Name Contains 1 to 256 characters Parameter Name Description Enable NAT Enable disable Network Address Translation NAT This function can be configure
9. ical change to this product without further notice Users may visit ZTE technical support website http ensupport zte com cn to inquire related infor mation The ultimate right to interpret this product resides in ZTE CORPORATION Revision History R1 1 20100325 Abridged version Serial No SJ 20100115161948 001 Publishing Date 20100325 1 Safety Instructions During Installation and Application Use the power adapter delivered with the product Other power adapter may make the device unable to work normally or even damage the device Check load capacity of power socket and power cable Overloading of power socket or broken power cable may cause an electric shock or fire It is recommended to check cables periodically and replace the broken one immediately Appropriate space for heat dissipation is required to prevent the product from overheating Keep the product away from heat sources Do not expose the device to high temperature environment and direct sunlight Keep the product away from moisture or vapor Do not splash any fluid on the product Do not place the product on any unstable surface Switch OFF and unplug this product carefully when it is not in use or before cleaning Pay attention to the high temperature on the surface of the transformer Delay between switching OFF and switching ON should be more than 3 seconds Do not block the heat dissipation opening of the product When the product is not used for
10. introduce the steps to disable IE proxy service 1 Select Tools Internet Options in the browser Then the Internet Options window pops up 2 Inthe Internet Options window select Connections tab and click LAN Settings 3 Uncheck Use a proxy server for your LAN in the pop up window Then click OK to submit 3 2 2 Configuring TCP IP The following uses Windows XP as an example to introduce the steps to configure TCP IP 1 In the Windows taskbar select Start Control Panel 2 Inthe Control Panel window double click Network Connection 3 In the Network Connection window right click Local Area Connection In the pop up menu click Properties Then the LAN Properties dialog box pops up 4 Select Internet Protocol TCP IP and click Properties Then the Internet Protocol TCP IP Properties dialog box pops up 5 There are two approaches to configure TCP IP However the first approach is recom mended e First approach Acquire an IP address automatically from H108L via DHCP a Inthe Internet Protocol TCP IP Properties dialog box check Obtain an IP ad dress automantically and Obtain DNS server address automatically b Click OK to save configuration e Second approach Specify a static IP address for PC a Inthe Internet Protocol TCP IP Properties dialog box check Use the following IP address to set the IP addresses of PC and H108L to the same network segment in the form of 192 168 1 x x is an integer between 2 t
11. n key corresponds to 5 ASCII characters or WEP Key1 WEP Key4 10 hexadecimal characters 128bit WEP encryption key corresponds to 13 ASCII characters or 26 hexadecimal characters 3 Click Submit button to complete WLAN security configuration 12 5 Troubleshooting You may encounter some problems when installing or using H108L Please try the following solutions If the problem still exists please contact the service provider for help Problem Solution The power indicator is off after the device is switched on Use standard power adapter such as the power adapter delivered with the device Make sure that the adapter is connected properly to both H108L and the power socket The LAN indicator is off after Ethernet cable is connected Make sure that the Ethernet PC and H108L are correctly connected and that the PC and H108L are switched on The DSL indicator is off after telephone line is connected Make sure that the telephone line in use is standard line delivered with the device and all devices are correctly connected according to the previous description Check whether the cables are properly plugged in Please allow 60 seconds for H108L to establish connection to the operator The DSL indicator flashes slowly after telephone line is connected Indicates that H108L failed to get connected with the DSLAM system of the operator Please make sure that H108L is correctly connected accor
12. nistration All stations communicating with H108L must use the same channel SGI Enable Enable di able SGI Configurable when 802 11n mode is enabled only Beacon Interval The default value is 100ms 10 Parameter Name Description Transmitting power level Options 100 80 60 40 and 20 The default value is 100 Transmitting Power Transmitting Power indicates the ration of the output power to the maximum power The higher the power is the longer the transmitting distance is QoS Type The default value is WMM 3 Click Submit button to complete WLAN configuration 4 2 3 WLAN Security Configuration 1 Select Network gt WLAN Security to open the WLAN Security Configuration page Choose SSID SSID1 x Authentication Type WPA PSK WPA Passphrase 12345678 8 63 characters WPA Group Key Update Interval 600 sec WPA Encryption Algorithm 2 Configure parameters on the basis of the following description Parameter Name Description Choose SSID The default value is SSID1 Options Open System indicating no encryption Authentication Type shared key WPA PSK WPA2 PSK and WPA WPA2 PSK WPA encryption key which contains 8 to 63 WPA Passphrase characters WPA Group Key Update The interval of WPA group key update The default Interval value is 600 seconds WPA entryption algorithm which supports TKIP AES and TKIP AES WPA Encryption Algorithm If users want
13. nmental Requirements Temperature 0 C 45 C humidity 5 95 Qualifications CCC Network Access License Wi Fi Radio Transmitter Model Authorization ZTE CORPORATION reserves the right to upgrade or make technical change to this product without further notice 14 NO 55 Hi Tech Road South Shenzhen P R China Postcode 518057 Technical Support Website http support zte com cn Customer Support Center E mail support zte com cn
14. o 254 For example IP is set to 192 168 1 2 subnet mask is set to 255 255 255 0 and both default gateway and DNS server are set to 192 168 1 1 b Click OK to save configuration 3 3 Configuring Wireless Connection 1 The PC is able to connect to WLAN network when it is equiped with wireless network card 2 Before the PC is able to get connected with a WLAN network the installation and configu ration of wireless network card must be completed 3 The wireless network card will search for wireless networks automatically after installation and configuration is completed The PC will be ready for use after search succeed If encryption is enabled on H108L users will be prompted for corresponding encryption key 3 4 Restoring Default Settings If the device fails to function or users forget their login password due to incorrect configurations the problem can be resolved by restoring default settings Refer to the label on the bottom of device for detailed default setting parameters 1 When the device is operating normally keep pressing the Reset button for more than 5 seconds using a needle or a pin 2 The system will restore default settings and restart automatically 4 WEB Configuration 4 1 Login Logout H108L provides Web based configuration which enables users to configure and manage H108L via Web browser 1 Type http 192 168 1 1 the default IP address of the LAN side interface of H108L in the address bar o
15. ring mode Options Always On On Demand and manual The mode is Always on by default Idle Timeout The default value is 1200 seconds It can be set when the Connection Trigger is set to On Demand only 3 Click Create to create connection 4 2 2 WLAN Configuration Select Network WLAN Basic 11n to open the WLAN Basic Parameter page as shown in the figure below Enable Wireless RF M Enable Isolation 7 Mode Mixed 802 11b 802 119 802 11r Country Region China Band Width 20Mhz Channel Auto SGI Enable UI Beacon Interval 100 Transmitting Power 100 QoS Type WMM Set the parameters according to the description below Parameter Name Description Enable Wireless RF Enable disable WLAN RF Enable Isolation Enable disable internal isolation Wireless communication mode including Mode Mixed 802 11b 802 11g and Mixed 802 11b 802 11g 802 11n Country Region Country or region where the device to be used Band width to be set Options 2OMHz and 40MHz Band Width The value is 20MHz by default Configurable when Mixed 802 11b 802 11g 802 11n is enabled only Wireless signal channel Select from auto and integ ers from 1 to 13 according to the country code The default value is Auto Wireless channel used in the communication between Channel the wireless access point and wireless station which channel to use depends on the local admi
16. to enable TKIP or TKIP AES encryption algorithm please firstly enable Mixed 802 11b 802 11g wireless communication mode Available encryption methods include WPA encryption WEP encryption and no encryption 11 WPA encryption Wi Fi Protected Access WPA includes WPA PSK WPA2 PSK and WPA WPA2 PSK a Select WPA PSK WPA2 PSK or WPA WPA2 PSK from the drop down list of Au thentication Type option to enable WPA encryption b Set the parameters according to the description above WEP encryption Wired Equivalent Privacy WEP is a widely used WLAN security protocol a Select Shared Key from the drop down list of Authentication Type option to open the page as shown in the following figure Choose SSID SSID1 Authentication Type Shared Key WEP Encryption Enable WEP Encryption Level 64bit WEP Key Index 1 lt j WEP Keyl 111111 WEP Key2 22222 WEP Key3 93333 WEP Key4 144444 13 ASCII chars or 26 hexadecimal digits can be entered for 128 bit WEP Encryption Key 5 ASCII chars or 10 hexadecimal digits can be entered for 64 bit WEP Encryption Key b Set the parameters according to the description below Parameter Name Description Enable disable WEP encryption The encryption is disabled by default WEP Encryption The length of WEP encryption key is 64bit or WEP Encryption Level 128bit WEP Key Index Index of WEP encryption key WEP encryption keys 64 bit WEP encryptio
Download Pdf Manuals
Related Search