User Manual
Contents
1. LO gt Colibr COVER SYSTEM leonarde CoLibri System Covering Machine User Manual CoLibri Pos eo System Covering Machine USER MANUAL Code MULEO1 0 Edition October 2006 Revision 1 0 x Viale Ortles 54 a CoLibri System S p A I 20139 Milano ITALY N Telephone 39 02 5220 181 Telefax 39 02 5220 1820 gt Website www colibrisystem com E mail colibri lint it Colibri COVER SYSTEM _ leonarde CoLibri System Covering Machine User Manual L COVER SYSTEM CoLibri System S p A All right reserved This manual has been prepared to help the user during the installation commissioning and normal use of the CoLibr Leonardo book covering machine The instructions drawings tables and other data contained in this document are technical information of a confidential nature No part of this manual may be reproduced and or disclosed without specific authorization from CoLibri System S p A Users are prohibited from disclosing the contents of this manual and from using this manual for purposes other than those strictly tied to the installation and normal use of the abovementioned equipment In order to guarantee the proper functioning of the machine all users must read and follow the instructions contained herein carefully Take care of this instructions manual and keep it in a place that is known and easily accessible If necessary the Customer may request a copy of this document for e2. To switch off the unit turn the main switch 1 to the O OFF position The display a will turn off to indicate that the unit is no more powered In case of an emergency and or to stop the unit from working disconnect the power plug from the wall socket to completely isolate the unit from the power supply Language Selection i l When necessary to select the language used for x displaying messages operate as follows I Ifthe unit is powered switch it off through the main switch 1 Switch on the book covering machine through the main switch while keeping both the cycle start levers pressed for at least 5 seconds As soon as the display shows the identification of the currently set language release the cycle start levers 2 Briefly and repeatedly press the cycle start levers to scroll through the selectable languages Italiano gt English gt Francais gt Deutsch gt Espanol 3 To confirm the chosen language and leave the programming mode keep the cycle start levers pressed for more than 5 seconds and release them as soon as the message Ready appears on the display I Ifyou do not press the cycle start levers for 30 seconds the unit automatically leaves the programming 5 sec IL mode saving the last selection made leonarde CoLibri System Covering Machine User Manual 9 Pos CoLibri SS COVER SYSTEM How to Cover Wrap Choosing the Size of the Cover Envelope The information
3. During the welding cycle do not turn the unit off by either disconnecting the power cable or switching off the main switch gt To obtain a correct welding trimming Ensure that the recommendations previously indicated on Choosing the installation site paragraph have been followed especially for what concerns the easy access to the unit height and leveling of the support surface Do not operate the unit remaining seated and do not exert pressure on the cycle start levers moving the arms but rather keep the arms stiff and bend your bust This allows you to apply an uniform and optimum pressure on both levers thus limiting the effort Keep the covers envelopes in the same room where the covering machine is installed to avoid sudden changes in material temperature gt After switching the power on and or after a prolonged stop run a control pre heating cycle idle cycle prior to starting a document object covering cycle 12 User Manual the trimming welding slot hold both cycle start levers and press them down firmly applying the same pressure on both of them to start the trimming welding cycle A Wait message shown on display indicates a cycle in progress Keep the levers pressed until the flashing message Finish appears cycle end signaling Now the book covering machine is ready to be used Without inserting a cover envelope in jl leonarde CoLibri System Covering Machine CoL
4. Leonardo book covering machine may be used to trim and weld only covers and envelopes bearing the original CoLibr marking or other material approved by the manufacturer To wrap Materials which have not been approved by the manufacturer are not guaranteed to be safe and non toxic When subjected to the thermal welding trimming process they might release harmful vapours or ignite The Manufacturer will not be held liable for any damage arising out of the use of covers envelopes made from material which has not been approved by it leonarde CoLibri System Covering Machine User Manual 29 OS CoLibri COVER SYSTEM Page left intentionally blank leonarde CoLibri System Covering Machine 30 User Manual gt gt Po CoLibri CoLibri System s p a Viale Ortles 54 a 20139 Milano ITALY Telephone 39 02 5220 181 Telefax 39 02 5220 1820 Website www colibrisystem com E mail colibri lint it
5. due to the friction exerted by the connectors e on the power terminals f I Exert an uniform vertical pull on both sides to avoid bending the welding bar and or damaging the power terminals 3 Install the new welding bar operating as follows I Pay attention to correctly orient the new welding bar In any case the special shape of the bar prevents wrong positionings gt Hold the new welding bar d through the knobs c then align the power terminals f of the welding bar with the relevant connectors e on both sides of the welding head gt Exert an uniform vertical pressure on both sides of welding bar to insert the power terminals into the relevant connectors and the welding bar itself into the relevant seat At the beginning of the insertion ensure that the power terminals f correctly match the relevant connectors e 4 Once you have correctly plugged the power terminals into the relevant connector tighten the three fastening screws of the welding bar and re install the work surface see step 1 At the end of the operation re connect the power cable Q I For details on ordering parts such as the welding bar refer to the section entitled Spare Parts and Consumables The welding bar is a part with a high environmental impact For this reason we do not recommend that it be disposed of with solid urban waste One should rather use the services of a specialized company and or comply with the
6. not correctly trim weld the cover envelope i e the scrap is not correctly cut or the welding is poor then INCREASE the welding time The welding time adjustment should be carried out step by step checking each time whether the obtained result ts satisfactory WARNING Setting the maximum welding time 8 seconds may cause a premature burning of the welding bar gt The Book Covering Machine Signals an Error Condition If at the end of the first trimming cycle carried out after switching on the unit the display shows Error instead of Finish then the book covering machine locks and prevents further cycles In such cases 1 Cycle off on the unit switching the main switch then try to carry out a new trimming cycle operating as described on paragraph Operating Precautions 2 Ifthe problem persists then repeat the step for a maximum of three 3 times 3 If after three 3 attempts the error condition is still signaled at the end of the first cycle then switch off the unit and call the customer service department leonarde CoLibri System Covering Machine 26 User Manual CoLibri i O COVER SYSTEM _ When to Contact the Customer Service Department Switch off the machine by switching off the main switch disconnecting the power cable and contact the customer service department in the following cases When you are unable to make the machine work properly even after you have followed the in
7. trimming operation is not being performed correctly 24 Notes about the Welding Tim initial 26 The Book Covering Machine Signals an Error Condition 26 When to Contact the Customer Service Department i 27 Spare parls andeonsumabies iprrcnonican a a aA a NE N a 28 User Manual eo narde CoLibri nes COVER SYSTEM Introduction The CoLibr Leonardo book covering machine is a semi automatic system used to cover any type of book or publication and may also be used to file save and protect documents photographs plans and objects Covering books or publications of any shape and size becomes a very quick and easy task using the CoLibr system s special transparent covers that are available in various sizes In fact no more than 20 seconds are needed to apply a resistant and perfectly adherent protective cover In addition the transparent cover is not sticky it does not alter the book cover and may be removed and replaced at any time When the book covering machine was designed the main aim was to create a ready to use compact unit that would be suitable to trim and weld covers in a safe simple clean and perfectly squared manner All these characteristics have been perfectly integrated in the CoLibr Leonardo a hi tech system which is accurate down to the last detail and which is also light handy fast and cost effective The system is particularly suit
8. able for stationery shops bookshops schools and libraries In addition because it is fast and easy to use the CoLibr Leonardo book covering machine is also the ideal solution for professional offices where architects editors photographers etc can use it to file projects documents sketches and drawings or to put objects photographs and printouts into envelopes Identification of Components 1 Welding head The welding head contains the main elements needed for trimming welding the cover e g the welding bar the control board the roller motor etc The external casing allows a rapid dissipation of the heat developed during the welding process and at the same time it prevents the user from touching potentially dangerous parts I A slight overheating of the welding head after extended use is normal In any event the accessible surfaces do not reach dangerous temperatures Special protections secured with screws give access to the integrated parts to facilitate maintenance I Any intervention on these parts other than those described in this manual must be carried out by qualified technical staff customer service staff leonarde CoLibri System Covering Machine User Manual 1 mos CoLibri LC COVER SYSTEM 2 Work surface Made of heat resistant and highly stable plastic material properly secured to the welding head the work surface provides a convenient support plane and facilitates cover insertio
9. able of the unit See the Installation and Connection section for further details 6 Main switch Turns the unit on off leonarde CoLibri System Covering Machine 2 User Manual CoLibri nes COVER SYSTEM S Technical Data Technical Technical specifications 22 x34 x16 15 22 l x 3 54 h x 16 15 d with 24V 180 VA integrated transformer Identification Warning Plates The following identification warning plates are applied to the bottom cover of the welding head of each CoLibri Leonardo book covering machine 1 Indicates to authorised and trained staff that the power cable must be disconnected before removing the protection cover 2 Indicates that the protection cover must not be removed and that unauthorised and untrained staff must not access the electrical section 3 Identification and CE marking plate Represents the unique product identification recognised by the manufacturer The data printed on this plate must be indicated each time a service is requested or when spare parts are ordered FORBIDDEN TO OPEN to unauthorised THE OPENING OF THE PANEL IS ALLOWED TO THE ELECTRICIANS ONLY CoLibr System S p A CE 000XX00000 Input AC 115 230 V Assembled bY MADE IN ITALY Fast Assembler srl leonarde CoLibri System Covering Machine User Manual 3 ros CoLibri COVER SYSTEM Installation an
10. chine can only be used to weld and trim CoLibr marked covers and envelopes or other material approved by the manufacturer kindly refer to the paragraph entitled Operating Precautions If the trimming operation is not performed correctly at gt the right left side or in DINI 7 the middle of the 7 15 cover envelope then the problem might be caused by an unparallel support surface Try to move the book covering machine 5 10 cm 2 4 to the right or to the left and N retry If the problem persists place the machine on another support surface also refer to the paragraph entitled Choosing the Installation Site OK The trimming operation is completed over the entire length of the cover envelope but the material is not welded satisfactorily or appears excessively melted plastic gloss generation In this case the problem is caused by an incorrect welding temperature welding time too short or too long IS The CoLibri Leonardo book covering machine is supplied from the factory already adjusted and calibrated for the most common applications installation sites The above problem could then result from an installation site where the temperature does not fall with the permitted range for further information refer to the paragraph entitled Choosing the Installation Site Should you be unsure as to whether you actually need to adjust the weldin temperature kindly contact the manufa
11. cturer s technical department to obtain the required assistance and information leonarde CoLibri System Covering Machine CoLibri nes COVER SYSTEM When necessary to change the welding time operate as follows I If the unit is powered switch it off 1 2 3 through the main switch Switch on the book covering machine through the main switch while keeping both the cycle start levers pressed for at least 10 seconds Release the cycle start levers as soon as the flashing message SET TIME x xX sec appears on display Briefly and repeatedly press the cycle start levers to increase with a step of 0 5 seconds the trimming time up to a maximum of 8 seconds I When reaching the max setting value 8 sec the trimming time re starts from 3 seconds To confirm the chosen language and leave the programming mode keep the cycle start levers pressed for more than 5 seconds and release them as soon as the message Ready appears on the display I Ifyou do not press the cycle start levers for 30 seconds the unit automatically leaves the programming mode saving the last selection made leonarde CoLibri System Covering Machine User Manual 25 COVER SYSTEM Notes about the Welding Time gt If after the trimming welding process the cover envelope shows an excessive amount of blur plastic filament or curling then DECREASE the welding time gt Ifthe book covering machine does
12. d Connection To correctly install and connect the CoLibri Leonardo book covering machine it is necessary to perform the operations referred to below in the order indicated working as set out in this chapter v Choosing the installation site v Unpacking and checking the components v Preparing and positioning the unit v Connecting the power cable Choosing the Installation Site To ensure the best operation of the unit the installation site must have the following characteristics _ 15 C 25 C 59 F 77 F The support surface must be sturdy and perfectly level failing which the unit might not ASN A RH 20 80 work properly Moreover it must be easily mC accessible not subject to excessive vibrations ddl and at a suitable height 80 85 cm 32 A 35 from the floor level Install the unit in a place that is not exposed to direct sunlight or atmospheric agents Leave sufficient space around the unit so that one can work comfortably and position it far from other electronic equipment to avoid interferences The installation site must have a temperature of between 15 C and 25 C 59 F 77 F and relative humidity RH of between 20 and 80 The unit might not work properly at a temperature of less than 15 C 59 F The installation site must be adequately ventilated free from dust and or condensation Do not install the unit near a humidifier To pre
13. e confirmed the correct alignment hold both cycle start levers and press them down firmly applying the same pressure to both of them to start the trimming welding cycle A Wait message shown on display indicates a cycle in progress Keep the levers pressed until the flashing message Finish appears cycle end signaling 4 Remove the book cover from the welding bar I Do not pull the book cover towards you lift it either from the left or the right side This allows you to obtain a clean separation of the cover and avoids plastic gloss appearing on the welding of the cover Gently fold the front cover of the book f and insert it into the left pocket g of the cover already trimmed to the required length 14 User Manual CoLibri COVER SYSTEM leonarde CoLibri System Covering Machine CoLibri Pos COVER SYSTEM TT 5 Close the book and turn the excess part of one side or on both sides of the CoLibri cover working as described in step 3 of this procedure The book has now been covered with a resistant tailor made and ease to remove cover How to Cover Hardcover Books I If necessary run a pre heating cycle as described above Then choose the cover size Mini or Standard suitable to the size of the book to be covered as described in the paragraph entitled Choosing the size of the cover envelope Lay the cover a on the work surface of the unit b with the t
14. e event of damage defects or differences being found I Keep all the packaging materials If it becomes necessary to ship or transfer the unit re use exclusively the original packaging Q In any event carefully dispose of the plastic or non biodegradable materials leonarde CoLibri System Covering Machine User Manual 5 Pes CoLibri COVER SYSTEM Positioning the Unit Once all the components have been removed from the package prepare the unit machine body working as follows gt With the unit in vertical position unfold the work surface then place the unit in a horizontal position on a table or on a proper support plane and set it in a comfortably reachable way As stated above in the section entitled Choosing the installation site the table or surface where you place the unit must be perfectly level Connecting the Power Cable 1 2 6 Insert the connector a of the power cable b included in the package into the supply socket c located at the back of the unit Connect the power cable plug d to an appropriate wall socket e that can supply the required voltage and frequency values and which is compatible with the power absorption of the unit leonarde CoLibri System Covering Machine User Manual Colibr nes GOVER SYSTEM a lO NEE To avoid being electrocuted or damaging the equipment take note of the warnings and observe the safety regulations set o
15. e under mentioned Harmonized Norms UNI EN ISO 12100 1 UNI EN ISO 12100 2 EN 50081 1 EN 50082 2 EN 60950 leonarde CoLibri System Covering Machine User Manual gt Colibri COVER SYSTEM 3 Table of Contents MARA IAI ON EEE l Identification of Gre 00 0 0 at 1c ene ee ne eniran ennienni NEE EEEE l Mein E es ET E E E E E E E E E E 3 Identification Warning Plates seseroercerienci aaa aa anaanatae 3 Installation and Connection iii 4 Choosing the Installation Site s 000rieezezezeze zena ze za zena aa 4 Unpacking and checking the components iii 5 EROTICA 6 Coi RR A Ena ananin 6 Hobbes 8 Operator LE ae ICE aeaiiai AAAA 8 Pot Oi aad O earen RRE droga za daiadazadaiagazadadaca 90503005 esse eee 8 Lanonape Seleclofi ar naria o a E AAEE EEN EEA EAEE EA EA E EEA 9 LEO ANZI ARA 10 Choosing the Size of the Cover Envelope iii 10 Covering Wrapping Procedures ii 11 Operating Piccolo ia 11 How to Cover Softcover Books 13 How to Cover Hardcover Books na 15 How to Encapsulate Documents Wrap Small Objects 18 Howto Gift Wrap PackapSS _ iii 19 Maintenance of the Iii 20 CIANO iii 20 Replacement ofthe Welding Baliani resi araba 21 Bice 11045 1 6 9 001 ARRECARE EEA 23 The book covering unit does not work L 23 The
16. ibri RD COVER SYSTEM How to Cover Softcover Books I If necessary run a pre heating cycle as described above Then choose the cover size Mini or Standard suitable to the size of the book to be covered as described in the paragraph entitled Choosing the size of the cover envelope Lay the cover a on the work surface of the unit b with the two pockets of the cover facing up the CoLibri logo printed on the cover should be legible on the bottom side of the cover 2 Insert the back cover of the book c into the right pocket d of the cover sliding it down flush with the bottom edge of the pocket 3 Close the book and insert the part min 15 mm 5 8 of the cover on the top side into the trimming welding slot of the unit Before trimming check that the bottom edge of the CoLibri cover is parallel with the horizontal reference lines on the work surface of the unit if necessary adjust the position of the pocket To be exact make sure that the length of the left pocket y is the same as that of the right pocket x If the CoLibri cover is badly trimmed it may be difficult or even impossible to insert the book cover into the left pocket and to complete the covering process leonarde CoLibri System Covering Machine User Manual 1 3 Once you have inserted the part of the cover to be trimmed into the slot e between the welding bar and the work surface of the unit and you hav
17. ith a soft dry cloth thoroughly clean the welding bar c and the relevant lower rabbet d removing any residue DO NOT use blades Q or sharp objects to clean the welding bar leonarde CoLibri System Covering Machine 20 User Manual CoLibri rog Replacement of the Welding Bar For good trimming and welding results we advise you to replace the welding bar after about 5000 trimming cycles see the cycle counter on top of the unit Ss The unit signals the need to check replace the welding bar when reaching 5000 cycles through a flashing for about 50 cycles of the cycle counter shown on LCD display To replace the welding bar Before proceeding we advise you to switch off the unit turning off the main switch and disconnecting the power cable Wait until the machine has cooled down During the welding bar replacement process pay attention not to damage the sensor integrated within the head 1 To make the operation easier it is advisable to lean the unit in vertical position as shown on the figure Using a Phillips screwdriver a of suitable size unscrew the three screws b which fasten the welding bar eonarde CoLibr System Covering Machine User Manual 21 nes CoLibri COVER SYSTEM 2 Grasp both knobs c secured to the welding bar d then pull the bar towards you to remove it from the relevant seat A certain resistance during the welding bar extraction is normal and it is
18. local rules and regulation in force leonarde CoLibri System Covering Machine 22 User Manual CoLibri COVER SYSTEM Troubleshooting To avoid creating potentially dangerous situations and or damaging the equipment do not carry out any troubleshooting interventions other than those described below gt The book covering unit does not work 1 Make sure that the machine is correctly 2 powered this is indicated by the Ready message on LCD display If the LED 1s off check that the power cable a is correctly plugged in and that the main switch b is turned to the ON position If the unit is correctly powered the green LED ON lights up be sure to simultaneously and firmly press both cycle start levers I To apply an optimum and uniform pressure on both levers do not operate the unit remaining seated and do not exert pressure moving the arms but rather keep the arms stiff and bend your bust As soon as you press the levers a Wait message shall appear on the LCD display onarde eo System Covering Machine User Manual 23 ros CoLibri COVER SYSTEM gt The trimming operation is not being performed correctly 1 2 3 4 24 User Manual Run a pre heating cycle working as described in the paragraph entitled Operating Precautions and retry Make sure that approved covers envelopes are being used the CoLibr Leonardo book covering ma
19. n and the welding trimming operations The serigraphy on the work surface not only helps one to find the correct cover size and to align the covers but also reminds one in graphical mode of the main steps needed to correctly complete the covering process The work surface which can be folded back thanks to a special hinge is fitted Ye E with rubber feet to ensure excellent aw stability This saves space when the machine is not being used 3 LCD Display Two rows LCD display showing useful information for the operator During the normal use the messages shown on the top row guide the operator through the trimming cycle while the bottom row indicates the number of welding trimming cycles carried out by the unit During the language and trimming time setup see relevant paragraphs the display shows the selectable settings 4 Cycle Start levers Once the document and cover have been correctly positioned firmly press both levers simultaneously to start the trimming cycle Special microswitches check that both levers have been properly pressed and if not they disable the start of the cycle This increases the safety of the unit as one cannot touch the welding zone during the cycle Suitable springs ensure that the levers return to the home position During the language and trimming time see relevant paragraphs it is possible to select the desired option acting on these levers 5 Supply socket Allows the connection of the power c
20. ng leonarde CoLibri System Covering Machine 16 User Manual CoLibri COVER SYSTEM 4 Remove the book cover from the welding bar I Do not pull the book cover towards you lift it either from the left or the right side This allows one to obtain a clean separation of the cover and avoids plastic gloss appearing on the welding of the cover Open the book and completely rotate the back cover as shown then lay the book completely open on the work surface of the unit insert the front cover of the book f into the left pocket of CoLibri cover g already trimmed to the required length To make the insertion easier pull the CoLibr cover out slightly from the back cover of the book Close the book and turn the excess part of one side or on both sides of the CoLibri cover working as described in step 3 of this procedure The book has now been covered with a resistant tailor made and ease to remove cover eonarde E CoLibr System Covering Machine User Manual 1 7 mos CoLibri lt a COVER SYSTEM How to Encapsulate Documents Wrap Small Objects 1 If necessary run a pre heating cycle as described above Then choose the size of the envelope 44 43 or A2 suitable to the size of the document working as described in the paragraph entitled Choosing the size of the cover envelope 2 Insert the document a into the envelope b sliding it down flush with the bottom edge of
21. reflected on the work surface of the CoLibri Leonardo book covering machine allows one to quickly and easily select the size of the cover envelope to be used to cover wrap the relevant document object a g A 3 S mis max cm 23 x 30 max g 6x 9in max 9 x 11 in max fa gt sf cm 5 max cm 8 max 2 in max 3 in max r cm 21 6x 28 cm 42 6 x 62 8 x11in 16 x 24 in SM DI cy cm 21 6 x 35 5 cm 21x 32 7 cm 29 7 x 45 8 x 14in 8 x12 in 11 x17 in CoLibri Covers for either Hard or Softcover Books Magazines Publications Align the spine of the publication with the reference line a then check the visibility of the other reference lines to select the cover size vV If the line b identified by the symbol X is visible use a CoLibri MINI size cover VY Ifthe line b is NOT visible use a CoLibri STANDARD size cover I A summary of the available cover sizes including the dimensions of both covers and publications that can be used expressed in mm and inches is illustrated in section I Check that the length of the book does not exceed the length of the CoLibri cover that is chosen For correct trimming and welding make sure that the excess part of the cover on the top to be trimmed is at least 15 mm 5 8 1 15 mm 5 8 min OK D leonarde CoLibri System Co
22. rless water resistant material which is up to 60 air permeable The covers provide protection against harmful light and are specially calendared for softness In addition the covers envelopes of the CoLibr system do not release fumes or harmful vapours during the welding process thus avoiding the need to install supplementary suction systems Materials which have not been approved by the manufacturer are not guaranteed to be safe and non toxic When subjected to the thermal welding trimming process they might release harmful vapours or ignite The use of this book covering machine for other purposes and or the use of covering material which has not been approved by the manufacturer may cause injury to persons or damage the machine itself Such conduct is therefore considered to be an Improper Use for which the manufacturer disavows all liability An Improper Use of the book covering machine will also result in the forfeiture of the warranty gt Never use the book covering machine near flammable surfaces or liquids leonarde CoLibri System Covering Machine User Manual 1 1 res CoLibri COVER SYSTEM gt Avoid spilling liquids such as water coffee other drinks etc on the unit Keep corrosive liquids and or solvents far away from the unit gt Prior to starting a cycle make sure that there are no clips staples or other objects except the cover envelopes between the welding bar and the lower contrast surface gt
23. structions contained in this manual or when the unit performs inconsistently When the unit has been dropped and damaged when the unit has been contaminated with liquids or has had water splashed on it When the unit requires repairs and or extraordinary maintenance of any kind To avoid creating potentially dangerous situations and or damaging the equipment do not carry out any troubleshooting interventions other than those described below Failure to observe this warning will absolves the manufacturer from any direct or indirect liability in the event of damage In all of the abovementioned situations kindly contact the customer service department indicating the serial number of the unit and the type of problem detected Should it be necessary to send the unit to the service centre pack it properly using only the original packaging which should be kept intact gt Remove the power cable from the unit See the Installation and connection section for more details gt Fold the work surface back and put the body of the machine inside the protective bag gt Insert the additional packing materials and then place the machine inside the original box gt Put all the accessory items into the box gt Close and seal the box with adhesive tape leonarde CoLibri System Covering Machine User Manual 27 CoLibr COVER SYSTEM Spare parts Welding bar E ERE Power cable I When req
24. terface The CoLibr Leonardo book covering machine is fitted with a liquid crystal display 1 showing information messages for the operator convenience During normal use the upper row a shows in the chosen language special wordings which guide the operator through the trimming cycle execution l e indicates that the unit is powered on and ready to start the cycle Wait once you have pressed the levers 2 this message indicates that the trimming cycle is in progress and that you must keep the levers properly pressed until the cycle ends flashing indicates the end of trimming cycle now you can release the levers and remove the covered document object The lower row b of the display indicates the number of welding trimming cycles 7677 in the above example carried out by the unit cycle counter it cannot be reset The display is also used to signal possible error conditions and to show the available options during the language and trimming time setup see relevant paragraphs Power On and Off To power on the unit simply turn the main switch J on the back of the welding head to the I ON position At power on the display a will show in sequence the wordings CoLibri SYSTEM V x xx and Ready The latter indicates that the unit is correctly powered and ready for use leonarde CoLibri System Covering Machine 8 User Manual CoLibri nes COVER SYSTEM xX
25. the pocket 3 Insert the part of the envelope to be trimmed min 15 mm 5 8 into the trimming welding slot c of the unit Before trimming check that the bottom edge of the CoLibri cover is parallel with the horizontal reference lines on the work surface of the unit Hold both cycle start levers and press them down firmly applying the same pressure to both of them to start the trimming welding cycle A Wait message shown on display indicates a cycle in progress Keep the levers pressed until the flashing message Finish appears cycle end signaling The document has now been covered with a resistant tailor made and ease to remove cover leonarde CoLibri System Covering Machine 18 User Manual CoLibri COVER SYSTEM How to Gift Wrap Packages I If necessary run a pre heating cycle as described above Then choose the size of the envelope either A4 A3 A2 CoLibri Gift Envelopes or A4 to A2 CoLibri transparent envelopes suitable to the size of the object working as described in the paragraph entitled Choosing the Size of the Cover Envelope 2 Insert the object a into the envelope b sliding it down flush with the bottom edge of the pocket 3 Insert the part of the envelope to be trimmed min 15 mm 5 8 into the trimming welding slot c of the unit Before trimming check that the bottom edge of the CoLibri cover is parallel with the horizontal reference lines on
26. the work surface of the unit Hold both cycle start levers and press them down firmly applying the same pressure to both of them to start the trimming welding cycle A Wait message shown on display indicates a cycle in progress Keep the levers pressed until the flashing message Finish appears cycle end signaling The object has now been gift wrapped and may be decorated with ribbons bows etc leonarde CoLibri System Covering Machine User Manual 1 9 res CoLibri COVER SYSTEM Maintenance of the Unit In order to avoid potentially harmful situations and or to prevent damage to the equipment refrain from carrying out any maintenance work that is not described in this manual Before starting any maintenance work switch off the unit turning off the main switch and disconnect the power cable I Failure to observe the warnings indicated herein will absolves the manufacturer from any direct or indirect liability in the event of damage and the warranty shall be immediately forfeited Cleaning Clean the unit at regular intervals removing dust and scraps of material etc that may have collected during the use of the unit Do not clean the unit with abrasive powders aggressive detergents solvents alcohol gasoline and similar products Use a soft dry cloth only Clean the work surface a of the unit thoroughly with a soft dry cloth and also the external surfaces of the welding head b W
27. uesting spare parts kindly specify the serial number of the unit as well as the part code I Only use original spare parts The Manufacturer cannot be held liable for damage arising out of the use of parts that are not original life are components with a high environmental impact For this reason we do not recommend that they be disposed of with solid urban waste One should rather use the services of a specialized company and or comply with the local rules and regulation in force n The parts which have been replaced and or the entire apparatus at the end of their leonarde CoLibri System Covering Machine 28 User Manual CoLibri nes COVER SYSTEM Consumable CoLibri covers STANDARD SV 0002 for books 49 x 32 cm 19 3 8 x 12 5 8 pack 250 pieces magazines catalogues etc MINI SV 0003 33 x 25 cm 13 x 9 9 4 pack 250 pieces CoLibri A4 BS 0013 i 21 x 32 7 cm 8 1 4 x 12 pack 50 envelopes p A3 BS 0014 documents 29 7 x 45 cm 11 8 x 17 3 4 pack 50 envelopes photos drawing A2 BS 0016 42 6 x 62 cm 16 3 4 x 24 3 8 pack 25 envelopes intel CoLibri SMALL A4 BR 0013 M gift envelopes 21 x 30 5 cm 8 1 4 x 12 pack 250 envelopes peor To wrap objects MEDIUM A3 BR 0014 M 30 x 45 cm 11 5 8 x 17 3 4 pack 250 envelopes initial LARGE A2 BR 0016M 47 x 53 5 cm 18 x 21 pack 125 envelopes IS The CoLibr
28. ut below Y DO NOT connect more than one equipment to the same supply socket and ensure that the electricity meter is not overloaded and can support the power absorption of the book covering unit vV If the wall socket and the power cable plug are incompatible use a suitable approved adapter Avoid using multiple sockets and or extension cables Do not damage or modify the power cable V The electrical installation to which the unit is connected must comply with the local regulations in force and must be fitted with the required safety devices to avoid the risk of electrocution or damaging the equipment V The wall socket used to supply the unit must be as close as possible to the unit itself The socket should be easily accessible to allow for immediate disconnection of the power cable in case of an emergency Y Do not touch the unit and or the supply socket with wet or damp hands and never work with the unit if you are not wearing shoes Y Do not pull the power cable out of the wall to disconnect the plug from the wall socket hold the plug Ensure that the power cable is not twisted placed under excessive strain crushed or pinched I Failure to observe the warnings referred to above absolves the manufacturer from any direct or indirect liability in the event of damage and the warranty shall be immediately forfeited leonarda ______ _ CoLibri System Covering Machine User Manual 7 How to Use the Unit Operator In
29. vent damage to the unit do not install it in OK a place where it will get splashed by water P 1_z_ lt To avoid sudden temperature changes do not install the unit near air conditioners heaters or other heat sources The unit should be installed near the wall socket used to supply electricity to the unit The socket should be easily accessible to allow for immediate disconnection of the power cable in case of an emergency leonarde CoLibri System Covering Machine 4 User Manual CoLibri nes COVER SYSTEM w Unpacking and checking the components Take the package to the chosen installation site handling it with care to avoid knocking or vibrating the package Follow the normal precautions regarding manual lifting of a load Open the package and carefully remove the unit and its accessories to avoid damage Check that the following items are in the package 1 2 3 4 5 7 Machine body with the work surface folded to save space Power cable Copy of this manual Quick Reference Guide CD ROM containing demo clips that show one how to Cp use the unit Colibr Accessory items placed inside protective bags leonarde Manuale Utente A E O Confirm that the package contains all the items listed above and check that the Ss main unit and its accessories have not been damaged during transportation Immediately inform the manufacturer in th
30. vering Machine 10 User Manual CoLibri i O COVER SYSTEM CoLibri Envelopes to Encapsulate Wrap Documents Drawings Maps Small Objects etc The section d of serigraphy shows a summary of the CoLibr envelope sizes available up to A2 including the dimensions of the envelopes and documents objects to be wrapped expressed in cm as well as in inches I To wrap objects special CoLibri gift envelopes are available in A4 A3 and A2 size Covering Wrapping Procedures The following procedures explain how to correctly and safely apply covers envelopes to books magazines objects etc In particular instructions are provided for the following How to Cover Softcover Books How to Cover Hardcover Books gt gt How to Encapsulate Documents Wrap Small Objects How to Gift Wrap Packages Operating Precautions gt The CoLibr Leonardo book covering machine may only be used to cover wrap books magazines documents projects photos objects etc Only adults are permitted to use the book covering machine Children are not permitted to use the unit Moreover the CoLibr Leonardo book covering machine may be used to trim and weld only covers and envelopes bearing the original CoLibr marking or other material approved by the manufacturer The CoLibr system s covers envelopes are the result of in depth research and development In particular they are made of a special highly transparent non toxic odou
31. wo pockets of the cover facing up the CoLibr logo printed on the cover should be legible on the bottom side of the cover leonarde CoLibri System Covering Machine User Manual 1 5 Pes CoLibri COVER SYSTEM 2 Insert the back cover of the book c into the right pocket d of the cover sliding it down flush with the bottom edge of the pocket 3 Close the book and insert the part min 15 mm 5 8 of the cover on the top side into the trimming welding slot of the unit Before trimming check that the bottom edge of the CoLibri cover is parallel with the horizontal reference lines on the work surface of the unit if necessary adjust the position of the pocket To be exact make sure that the length of the left pocket y is the same as that of the right pocket x If the CoLibri cover is badly trimmed it may be difficult or even impossible to insert the book cover into the left pocket and to complete the covering process Once you have inserted the part of the cover to be trimmed into the slot e between the welding bar and the work surface of the unit and you have confirmed the correct alignment hold both cycle start levers and press them down firmly applying the same pressure to both of them to start the trimming welding cycle A Wait message shown on display indicates a cycle in progress Keep the levers pressed until the flashing message Finish appears cycle end signali
32. xample where the original document is damaged by making written request to CoLibri System S p A undertaking in each case to return the damaged copy The manufacturer denies any liability for any inaccuracies contained herein arising out of printing or transcription errors In addition the manufacturer reserves the right at any time to make changes aimed at improving the product and bears no obligation to communicate such updates except for any modifications relating to safety All the trademarks referred to herein are trademarks which are owned by or which are registered in the name of the individual producers and as such are protected leonarde User Manual CoLibri System Covering Machine CoLibri Pos COVER SYSTEM x CE Conformity Declaration according to the relevant European Directives CoLibr System S p A declares that the semi automatic CoLibr Leonardo system intended to apply a suitable protective film to books covers documents or objects complies with the regulations contained in the following Directives Directive 98 37 CE concerning Machine Safety Directive 89 336 CEE concerning Electromagnetic Compatibility as amended by Directives 92 31 CEE and 93 68 CEE Directive73 23 CEE concerning Electric Equipment Safety Low Voltage as amended by Directive 93 68 CEE CoLibri System S p A further declares that in respect of its design and manufacturing it has adopted the principles and concepts contained in th
Download Pdf Manuals
Related Search