USER MANUAL
Contents
1. P s F 3 DO NOT position heater close 4 DO NOT move heater from room furniture ES i ff fF ap DO NOT position heater close to walls furniture net curtains bed linen or any other inflammable materials as this could result in the risk of fire The following minimum distances should be respected 50cm from side 100 cm from front ALWAYS face heater towards center of room The heater should be positioned on a level surface at all times to room when lit If a leak is suspected turn the gas off at the cylinder DO NOT disconnect the regulator Check alll connections Slowly turn the gas on and brush the connections with soapy water or liquid detergents a gas leak will form bubbles If a leak is found turn the gas off DO NOT use the heater again until it has been checked by a competent person accordance with the Gas Safety installations use Regulations 1998 min 500mm min 1000mm min 1000mm USING ENVIRONMENT Your heater consumes oxygen while it is in function For that reason adequate ventilation should be provided in rooms in which the heater is used This ensures the removal of products of combustion and allows the entry of replacement alr Adequate ventilation should considerably reduce the possibility of condensation occurring The following table shows the smallest sizes of room suitable for each heat setting and the2. ventilation FOR CATALYTIC HEATER MODELS Number of radiant VENTILATION continuously IN USE Low level High level 40 cubic meters 4m 4m 2 5 40 2 70 cubic meters 7mM 4m 2 5 70 2 105 cubic meters 105m 4m 2 5 105cm2 105cm2 1 This appliance requires a hose and a regulator 2 Only use well ventilated areas 3 Do not use In vehicles caravans or auto caravans 4 Do not attempt to use in high rise flats basements bathrooms or bedrooms 5 Do use your heater while sleeping person in accordance with the Gas Safety installations and use Regulations 1998 3 If any parts need replacing they should be replaced only with the correct parts supplied by the original manufacturer IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002 96 EC At the end of its working life the product must not be disposed of as urban waste It must be taken to a special local authority differentiated waste collection centre or to a dealer providing this service Disposing of a household appliance separately avoids possible negative consequences for the environment and health deriving form inappropriate disposal and enables the constituent materials be recovered obtain significant savings energy and resources As a reminder of the need to dispose of household appliances separately the product is marked with a crossed out wheeled dustbin purpose
3. READ INSTRUCTIONS CAREFULLY READ AND FOLLOW ALL INSTRUCTIONS PLACE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE ONLY USE IN A WELL VENTILATED AREA USER MANUAL FOR GAS AND QUARTZ TUBE HEATER CR 7010 WARNING IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE PERSONAL INJURY OR LOSS OF LIFE TECHNICAL CHARACTERISTICS Type GAS AND QUARTZ TUBE HEATER Dimensions 42 36 72 D W H WARNING 1 THE APPARATUS IS NOT READY FOR THE PHYSICALLY WEAK SLOW RESPONSE OR MENTAL DISORDERS INCLUDING CHILDREN TO USE UNLESS IT BEARS RESPONSIBILITY FOR THE GUIDANCE OF SAFETY OR SAFE USE OF THE HELP 2 CHILDREN SHOULD BE MONITORED TO ENSURE THEY DO NOT PLAY APPARATUS 3 HEATER IS NOT LOCATED IMMEDIATELY BELOW A SOCKET OUTLET 4 WARNING THIS HEATER IS NOT EQUIPPED WITH A DEVICE TO CONTROL THE ROOM TEMPERATURE DO NOT USE THIS HEATER IN SMALL ROOMS WHEN THEY ARE OCCUPIED BY PERSONS NOT CAPABLE OF LEAVING THE ROOM ON THEIR OWN UNLESS CONSTANT SUPERVISION IS PROVIDED SAFETY PRECAUTIONS 1 Always use heater in accordance 2 DO NOT place clothes or other with instructions supplied with each materials on the heater This could cause heater a fire risk and or affect the efficiency of Keep instructions in a safe place the appliance Bag i i yf a ii y ty te f 7 7 af A i the ah ms AV ba Rs a IN
4. liance and unplug from outlet when not in use and before cleaning Allow it to cool down If the supply cord is damaged it must be replaced by a service agent or equivalent qualified persons otherwise may cause a hazard To protect against fire electrical shock and injury to person do immerse appliance power cord plug in water or other liquid This appliance is indoor use only SYMPTOMS FAULT REMEDY 1 24 Do handle plug with wet hands 25 appliance has to be unplugged from the wall socket using the damp cloth to wipe the enclosure and then dry with dry cloth Pilot will light automatically Pilot will light automatically but points a to e are satisfactory and the pilot will light with a match Heater will remain alight when pressure is released from ignition button Smell of Combustion FAULT FINDING CHART 4 No spark across electrode gap Incorrect position of spark in relation pilot gas flow Electro magnetic valve closes whilst heater is alight Heating temperature become lower than usual Ensure that piezo electric ignition is functioning correctly Check that electrical lead is not damaged Check the battery power if the heater fitted with Push ignitEr and replace a new one Re position spark plug so that spark jumps across gas flow 0 0 Ensure that thermocouple probe is l
5. ocated in pilot flame Ensure good connection between thermocouple and valve Check thermocouple Check electromagnetic valve Damage of the catalytic pad Gas leakage from the gas circuit pipe Faulty regulator Hose ageing For your safety purpose call local service center if you have problems position 2 4 TURN OFF THE HEATER Turn off heater at cylinder or turn the switch on the regulator to the OFF position If the heater is not used for a period of time disconnect the regulator from the cylinder and replace any value protection plug or cover WARNING 1 2 9 8 14 15 Read the instructions before using this appliance The apparatus is not ready for the physically weak slow response or mental disorders including children use unless bears responsibility for the guidance of safety or safe use of the help Children should be monitored to ensure they do not play apparatus Use an appropriate regulator asks your supplier to get one Never attempt light if the hose is loose or damaged any way Do not press the ignition button for more than 40 seconds Never disconnect the regulator while cylinder valve or regulator is open Do not change cylinders in areas in which open fire exists Do not expose your cylinder to extreme heat Do not store any other cylinders the room in which your heater is used not insert y
6. ore take out the cylinder Turn off at the regulator and allow the heater to cool fully before removing and replacing the cylinder Do not attempt to replace the cylinder whilst the heater is still running Cylinders must be replaced flame free environment d Do not smoke while changing the cylinder When you need to replace your empty cylinder turn the gas off at the valve or regulator of the cylinder and take the empty cylinder out of the heater f Remove the regulator from the empty cylinder g Following the steps described under connecting the cylinder connect a new cylinder HEATING TUBE CONTROL Plug in the heater and then set the First and Second to select expected power First heating tube rated power input 500W Second two heating tubes rated power input 1000W Both Three heating tubes rate power input 1500W IGNITION MEDIUM For First Tube For Second Two
7. our finger any other material through the front panel of the heater Leave at least 1 meter distance between your heater and the other heat source Do not unauthorized persons to tamper with your heater Do not place appliance under electrical socket outlets Do not use the heater in bathrooms shower of swimming pool or leisure vehicles such as caravans or auto caravans This heater must not be used without a gas cylinder fitted for stability REPAIRS SHOULD ONLY BE CARRIED OUT BY A COMPETENT PERSON IN ACCORDANCE WITH THE GAS SAFETY INSTALLATIONS AND USE gt REGULATIONS 1998 CONSTRUCTION AND FUNCTION LIGHTING INSTRUCTION 8 Pos Pos 2 Pos 3 xa o 66 7 66 1 LIGHTING INSTRUCTION The heater has three settings Lighting and Minimum 1 Medium 2 and Maximum Pos 3 B Place the gas filled cylinder into the back of the heater C Clip on the gas regulator to the gas cylinder 3 D Turn on the gas regulator 2 LIGHTING Press the control button for 10 seconds at the Position 1 at the same time press 4 the piezo igniter key light with thumb finger of hand Continue this procedure until pilot ignites approximately after 20 seconds leave control button 1 _ At this stage if the pilot is alight it means that the heater is at the minimum the position Pos 1 If the pilot flame goes out please re
8. peat this procedure gt 3 HEAT SETTINGS To change from minimum to maximum gently press control button and turn it to Igniter gas control knob Gas burner safety guard ODS System position 3 To change from maximum to medium gently press control button and turn it oe CONNECTING THE CYLINDER 1 Place the gas filled cylinder into the back of the heater Clip on the gas regulator to the gas cylinder Turn the regulator on a ee Where the regulator is not supplied please contact your gas dealer to advise of correct type for the gas cylinder being used 5 IMPORTANT TEST FOR LEAKS This must be carried out in a well ventilated area free from naked flames and any other sources of ignition With the regulator connected to the cylinder turn on the regulator control Brush all hose connections pipe connections to the valve and gas cylinder valve with 50 50 solution of detergent and water A stream of bubbles forming indicates a leak If a leak is found turn off at the regulator and disconnect the regulator from the bottle and remove the gas cylinder outdoors to a well ventilated area Contact your gas supplier for assistance DO USE THE HEATER 6 After leak testing is satisfactorily carried out close the back door of the heater It may be necessary to move the heater slightly to allow the regulator and hose fo fit in the back without kinking the hose HOW TO CHANGE A CYLINDER a Unplug the heater bef
9. r Do not expose the gas bottle to the full summer heat nor too near any other heat source Do not place a heater in use near curtains furniture wood paneling or combustible material which can deteriorate with heat While in use ensure that children do not approach the heater Do not move the appliance when in use the safety device may be activated by knocks or movement This appliance should be tested for leaks before initial use and whenever the cylinder is re connected It is important that all gas connections have been correctly made to prevent any leakage Do not use naked flame test for leaks Call your supplier ask support Always use your cylinder always in an upright position Always turn off the regulator control when the heater is not in use When lighting your heater for the first time or after a period of time has passed since the last use light the heater outside and burn outdoors for 15 minutes The guard on the appliance is prevent risk of fire or injury form burns and no part of it should be permanently removed It does not give full protection for young children or the infirm We would recommend a fireguard to be fitted Only connect the apparatus if the voltage indicated on the type plate corresponds with the mains voltage In order to avoid overheating do not cover the heater by towels curtains or suchlike Do not unplug by pulling on cord To unplug grasp the plug not the cord Turn off the app
10. s 17 Do not cover your heater Fabrics clothing hanginos net curtains bed linens and other flammable materials may ignite if placed against the outlets of your heater 18 In the event of leakage the appliance should be turned off at the regulator switch on valve and the regulator disconnected from the cylinder 19 After use turn off the appliance at the gas container valve 20 Only use in a well ventilated area STORAGE 10 1 Disconnect cylinder 2 Store cylinder in a well ventilated area away from combustible material Storage preferable be in an outhouse but must not be in a basement or high rise flat 3 The heater should be covered in a dry dust free area in its original packaging CLEANING 1 Make sure unplug the heater before cleaning Turn of your gas supply at the regulator Use a damp soapy wrung cloth clean the exterior and cylinder storage area of your heater 4 Make sure that no water gets onto the burners or pilot light area Wipe the heater dry before use 5 Don t use abrasive cleaners as they may damage the quality paint finish MAINTENANCE 1 Check flexible tubing between regulator and heater regularly and replace if perished worn or damaged In any case replace tubing taking into consideration the expiration date 2 It is recommended that the heater be serviced every year by a competent 13 14 15 19 20 2 22 23 Do not store flammable liquids material near the heate
Download Pdf Manuals
Related Search