Operating Instructions TLON Manager V1.2
Contents
1. Hame Humber Type EBLo12 G wo2 Subnet Subnet 1_1 Channel Channel_1 kd Description The dialog box and the following actions are described in the example in chapter Create a New Project page 18 and continues in chapter Installation of a Project page 21 NOTE When all the EBL512 units nodes have been installed it is very important that you click Update all and Save all as described in the example After that it is recommended to restart each EBL512 unit 235 NOTE In a network with two or more Routers Channel_2 is normally used for the Backbone net and no EBL512 units nodes must be connected Or click the right mouse button to get a pop up menu select New unit or select Unit in the Network menu 30 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 11 Operating Instructions TLON Manager V1 2 File menu 11 1 11 2 11 3 11 4 11 5 New Creates a new Project Se chapter Create a New Project page 16 Open Opens an existing Project in TLON Manager s common data base Select a project in the list and click OK Close Closes the project that is open Delete Deletes an existing Project in TLON Manager s common data base Select a project in the list and click OK Import To be able to open a Project that for example has been copied from another PC see chapter Copy from disk page 33 or to be able to open an2. TLON Manager files It is recomended to use the following path for your TLON Manager files It is recommended to use the default path for the TLON Manager files Click Next LonWorks files It is recomended to use the following path for your LonWorks files Destination Folder C LonWarks Browse Cancel It is recommended to use the default path for the LonWorks files Click Next 11 Panasonic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 Select Program Folder Operating Instructions TLON Manager V1 2 Setup will add program icons to the Program Folder listed below fou may type a new folder name or select one from the existing Folders list Click Next to continue Program Folders TLON Manager 1 2 Existing Folders Accessories ACD Systems Administrative Tools Adobe CorelDRAW Graphics Suite x3 Creative CyberLink PowerDYD Echelon Drivers Games M4 Click Next Start Copying Files lt Back Cancel Setup has enough information to start copying the program files If you want to review or change any settings click Back If you are satisfied with the settings click Next to begin copying files Current Settings TLON Manager files will be copied to C Program Files TLO LonWorks files will be copied to C Lon Works Sif files will be copied to C xif LNS database files will be copied to C LNS Click Next Setup Complete
3. Channel 1 Cancel Select the channel to remove and click Remove 39 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 14 3 Operating Instructions TLON Manager V1 2 You will be asked if the Channel really shall be removed Click Yes or No Routers Select Router in the Network menu The following dialog box displays TLON Manager 1 2 New router Router Fouter_0 Type Leaming Router oo Hear Far Channel Channel Channel Subnet_1_1 Channele Subnet_1_3 Remove Select the router to remove and click Remove You will be asked if the Router really shall be removed Click Yes or No 40 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 15 Operating Instructions TLON Manager V1 2 Maintenance and troubleshooting 15 1 Some TLON information is saved in the EBL512 TLON connection board 1590 memory and some in the EBL512 Main board 1556 memory If only the Main board 1556 is replaced Do Update and Save for the node If only the TLON connection board 1590 or if both the boards are replaced Do Replace Update and Save for the node There are a number of functions that are useful for network maintenance and troubleshooting The most common are described below See also chapters Network troubleshooting page 51 and Network maintenance page 52 Wink With Wink you can check that
4. Subnet 2 Channel 2 Add Remove Create Cancel 5 Click Create to start binding all the nodes in the list to the Project Click Cancel to close the dialog box without binding any nodes The binding process might take some time After the binding process in the TLON Manager window s tree view there will in this example be added three nodes EBL512 units 11 10 Print It is possible to print some information about the project e g Project Name Path Number of nodes Number of subnets Number of routers Individual node information 11 11 Print preview A preview of the information that will be printed 36 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 12 Import xif files Development and improvement may result in new units Security Management systems etc that can be connected as a node in the TLON network New xif files can be imported to each Project Select Import xif in the Network menu The following dialog box displays Look in ke File name xi Files of type Cancel Select the folder and the xif file to import The following are available today Tlonmip xif for EBL512 GW512 SecmasAlarm xif for TLONDDE Server Interv xif for Securimaster Alarm 1 43 connection Click Open and the selected xif file will be imported It will now be possible to select this new type of node in th
5. old Project when a new version of TLON Manager has been installed the Project has to be imported to TLON Manager s common database Select Import in the File menu The following dialog box displays Directory Selection Eg Project dddd a 3 J sysbem_xye 5 drive c Cancel Find and select the folder Project to be imported As default TLON Manager saves all projects in C LNS The Project name will be the same as the folder name You may use this name or change it 31 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 11 6 Operating Instructions TLON Manager V1 2 Export Used when you want to export a Project You will get a copy of the Project in another folder From this folder it is possible to copy the project to e g a floppy disk CD Export can be used if you want a backup of the project or want to use the Project in another PC Select Export in the File menu The following dialog box displays Select from Project dddd F Spstem_spz B System_xyz My Documents aa My Cantar ey Places Save as type Cancel Find and select the folder to which the Project is to be exported As default TLON Manager suggests C LNS The File name Project name will be the same as the folder name You may use this name or change it Click Save The project will now be copied to the selected folder 7 NOTE It is not possibl
6. Setup has finished installing TLON Manager 1 2 on your computer Setup can launch the Read Me file and TLON Manager 1 2 Choose the options you want below Click Finish to complete Setup Click Finish to finish the In the following folder you TLON Manager installation will find a Shortcut to TLON Manager 1 2 and TLON Manager 1 2 Help respectively C Documents and Settings All Users Start Menu Programs TLON Manager 1 It is possible to send the Shortcuts to the desktop NOTE After a program installation it is always recommended to restart the PC 12 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 It is also recommended to check that the path is correct 1 e do as follows In Windows Explorer use the right mouse button and click My Computer in the menu select System Properties Open the Advanced System Settings tab and click Environment Variables Check in User variables that the Path is C LonWorks bin If not change it r Environment Variables Value C LonWorks bin USERPROFILE AppData Local Temp 4USERPROFILE AppData Local Temp System variables Variable Value ComSpec C Windows system32 cmd exe FP_NO_HOST_C NO NUMBER_OF_P 2 OnlineServices Online Services rT The following message might appear TLON Manager 12 7 ozs If this message ap
7. System_xyz and that you have one Channel Subnet_1_1 with two EBL512 units Node_0O and Node_1 20 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 The red frame around each EBL512 unit indicates that the unit is not installed 9 The project is now created and can be closed or installed see Installation of a Project below 6 1 Installation of a Project The TLON Network cable installations have to be finished and the EBL512 units have to be connected to the network NOTE In a Project with Routers they have to be installed before the nodes see chapter Installation of Routers page 28 Plug the PCC 10 card cable into any of the EBL512 units on Channel_1 The modular connector J2 RJ45 is to be used 10 Start TLON Manager and Open the Project e g System_xyz 11 In the dialog box select the Node_0 icon and click the right mouse button to get a pop up menu 12 Select Install If you have made a jump from 6 a at page 19 TLON Manager 1 2 2 Install unit must be attached Click Yes 13 A dialog box displays Waiting for service message Activate service pin Type of node Meuron id Start installation automatically when ZENICE Metsage is received OF Cancel OK Activate service pin is blinking In the EBL512 unit that is intended to be number zero CUOO shunt momentarily th
8. TLON Manager window the tree view the Routers and Channels are not shown i e no icons and no text Only the Subnets are shown 9 1 Installation of Routers The TLON Network cable installations have to be finished and the Routers have to be connected to the network NOTE The Routers have to be installed before the nodes can be installed otherwise there will be no communication with the nodes connected on the Channels on the other side of the Router s Plug the PCC 10 card cable into any of the EBL512 units The modular connector J2 RJ45 is to be used 1 Start TLON Manager and Open the Project 2 Inthe Network menu select Router 3 In the dialog box select a Router in the Name column and click Install If you have continued from page 27 i e chapter Add a Router Save alt a the following dialog box will be displayed TLON Manager 1 2 LY Install unit must be attached Click Yes 4 A dialog box displays 20 From now on use the same EBL512 unit at all times or an EBL512 unit on the same Channel Channel_1 I Tt is situated close to the connector J1 for PC Win512 connection i e below and to the right of the keypad on the EBL512 front 28 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 Waiting for service message Activate service pin Type of node Meuron id Vv Stark instal
9. Typ II PC Card e Turn on the PC Windows will now find the new hardware device Follow any wizard instructions e Check in the Control Panel that the LonWorks Plug n Play icon a a te 1S created e Double click the icon to open the following dialog box LonWorks Plug n Play Device Selected LON r Transceiver NI Application Diagnostics NSIPCC k System Image Path jc Mlonworks images pect 0 iY Automatic Flush Cancel General Settings Uplink Buffering i Select the numeric base for all LonWorks LON1 Plug n Play devices Version 3 04 000 Bo av coea The NI Application shall for a laptop PC with PCMCIA slot be NSIPCC else NSIPCLTA For Windows Vista the Uplink Buffering is 6 and the Version is 3 05 000 Click Diagnostics The following information box shall be displayed or a similar depending on the Windows type etc LON1 Diagnostics i Test Comm Service Restart Reset Comments LonWVorks PCC10 PCLTA10 PCLTA20 Device Driver Version 2 Card Type PCC 10 Driver Status Number of Free LTA Output Buffers Non Priority 0 Priority Loaded Image Size 49408 Interrupt Count 0 For Windows Vista the Version 2 03 and Loaded Image size 57344 If negative information is displayed it might depend on a device collision etc Check IRQ addresses and make changes when required Panasonic Electric Works Fire amp Security Tec
10. file Is there need for an additional channel Import xif Unit Channel New unit Router Add more Continue 49 Panasonic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 Operating Instructions TLON Manager V1 2 Continued Remove xif Is there need to remove an xif file Yes Should the project be used in another PC Finished 50 Panasonic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 Operating Instructions TLON Manager V1 2 16 2 Network troubleshooting Most of the functions in the flowchart below are described in chapter Maintenance and troubleshooting page 41 Wink What physical unit EBL512 is programmed in LON Manager Detail info Detailed information about the node and its status Update Download the network config data to a physical node Finished 51 Panasonic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 Operating Instructions TLON Manager V1 2 16 3 Network maintenance Most of the functions in the flowchart below are described in chapter Maintenance and troubleshooting page 41 Remove Remove a Node Channel or Router No Restart Restart a physical node EBL512 Property Change the name number or description for a node Finished 52 Panasonic Electric Works Fire amp Sec
11. for the project Normally use the same name as the System Name in Win512 e g System_xyz Max 23 characters Path The path will be automatically created when you type the name e g CALNS System_xyz Network interface Look in the Control Panel Lon Works Plug n Play dialog box Device selected Select the same here normally LON1 Import xif In a TLON network where only EBL512 units shall be connected mark the EBL512 GW512 checkbox default If a Security Management system also shall be used in the TLON network mark the check box respectively NOTE Development and improvement may result in new units Security Management systems that can be connected in the TLON network New xif files can be imported and xif files can be removed via the Network menu 2 Click OK to save the settings and close the dialog box The TLON Manager window displays EBLS512 units only or EBL512 units and Router s An information box Initiating network will be shown 17 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 TLON Manager 1 2 DEAR Fie Network Tools Show Help S El Network statuz Project System_ yz Eg Path C Mlns System_syz he System eye Py Subnet_1_1 lt Chamel gt jet Deillio Update all Save all 3 In this example no Channels or Routers shall be added Now the units i e EBL512 have to b
12. from a channel subnet to another In the dialog box specify the New location and click OK Control Normally not used in TLON Manager Save After Update see below you shall click Save so that the updated data is saved in the unit respectively Auto Bind Normally not used since it is already set as default in Settings Restart You can restart a node in the network with the restart command In the TLON Network this command works only on EBL512 units Select the node and click the right mouse button to get a pop up menu Select Restart The following dialog box displays TLON Manager 1 2 2 Are you sure Click Yes or No If TLON Manager can not communicate with restart the node the following message displays 42 Panasonic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 15 9 1 15 9 2 Operating Instructions TLON Manager V1 2 TLON Manager 1 2 Click OK to close the message box Restart subnet You can restart see above all the nodes on a Subnet Channel Select the Subnet and click the right mouse button to get a pop up menu Select Restart The following dialog box displays TLON Manager 1 2 i Are you sure Click Yes or No If TLON Manager can not communicate with restart a node see the status line the following message displays TLON Manager 1 2 Click OK to close the message box Restart network Yo
13. g Subnet _1_1 Subnet_Subnet l_Channel 1 i e Channel 1 Subnet_1_2 Subnet_Subnet l_Channel 2 i e Channel 2 Subnet_1_3 Subnet_Subnet l_Channel 3 i e Channel 3 and so on Use the dialog box Create subnet only to view the list of Subnets in the Project 1 Select Subnet in the Network menu TLON Manager 1 2 Create subnet Hame Subnet_2 Humber 2 Subret_1_1 Save Cancel Name A default name for the next subnet to be added Normally the default name is used but information can be added Number A default number for the next subnet to be added List field A list of the existing Subnets in the Project New Adds the next subnet in the Name field e g Subnet_2 Remove Removes a Selected subnet Save Adds the Subnet in the Name field e g Subnet_2 to the list Cancel Closes the dialog box 18 E g Subnet_1_2_ Backbone 23 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 9 Add a Router Regarding Routers in a TLON Network see chapter Planning a Project Routers page 14 Two or more Routers have to be connected via a Backbone net Use Channel_2 for the Backbone net Select Router in the Network menu A dialog box displays TLON Manager 1 2 New router Router Type Leaming Router oo Near EB Ea il Updsie Crase ee ams Bete Ee R
14. Panasonic Operating Instructions MEW00460 Revision 4 TLON Manager V1 2 Author Jan Pettersson Date of issue 2004 05 24 Date of rev 2009 04 14 File name MEW00460 Rev 4 doc This page has deliberately been left blank Panasonic Electric Works Fire amp Security Technology Europe AB Operating Instructions TLON Manager V1 2 MEWO00460 Rev 4 Table of contents 1 1 1 2 3 3 1 52 4 5 5 1 Introduction Definitions TLON Manager kit 1595 1595SE Installation of the LonWorks PCC 10 card Installation of the PCC 10 drivers Installation of the PCC 10 PCMCIA card Installation of TLON Manager Project Planning a Project 5 1 1 Channels Subnets sA e Routers 5 1 3 EBL512 units nodes a2 6 6 1 7 8 9 9 1 10 11 11 1 11 2 11 3 11 4 11 5 11 6 11 7 11 8 11 9 11 10 11 11 12 13 14 14 1 14 2 14 3 15 Planning Creating a project Create a New Project Installation of a Project Add a Channel Subnet Add a Router Installation of Routers Add a Unit File menu New Open Close Delete Import Export Copy from disk Copy project NW Wizard Print Print preview Import xif files Remove xif files Remove Nodes Channels Routers Maintenance and troubleshooting O nn amp WH U 10 14 14 14 15 15 15 16 21 24 25 26 28 30 31 31 31 31 31 31 32 33 34 35 36 36 37 38 39 39 39 40 41 Panasonic Electric Work
15. The node may be updated later see chapter Update page 44 46 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 TLON Manager 1 2 i 2 Are you sure Click Yes or No If TLON Manager can not communicate with restart a node see the status line the following message displays TLON Manager 1 2 Click OK to close the message box Update page 43 Click OK to save and close the dialog box 47 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 16 Flowcharts The following flowcharts will help you creating a TLON Network as well as TLON network troubleshooting and maintenance The text in the command blocks refers to the chapters in this document 16 1 Create a TLON Network Create a new project or use an existing Existing Copy Open a project or use a copy from a disk Create Open Copy from disk Import Create a completely new project or copy an existing project and rename it New Copy project Create a project Continue 48 Panasonic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 Operating Instructions TLON Manager V1 2 Continued What shall be added 1 Channel 2 Router 3 Unit Unit Router Yes Need to import an xif
16. X E F etc depending on which USB connector you use Put the USB Memory stick in one of your PC s free USB connectors Select the TLON Manager folder and the SETUP EXE file i e F TLON Manager SETUP EXE Double click the file name SETUP EXE If the following displays click OK Information _ 1 UseDLL failed Couldn t load DLL file 1595 Operating Instructions TLON Manager V1 2 MEW00460 i e this document in PDF format 1595SE Swedish document TLON handbok in PDF format 10 Panasonic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 Operating Instructions TLON Manager V1 2 lt TLON Manager 1 2 Setup TLON Manager 1 2 Welcome to the TLON Manager 1 2 Setup program This progam wil ratal TLON Manage 1 2 on your computer It is strongh eecommended that you ext all Windows programs befote running this Setup program Dick Cancel to quit Setup and then close any programs you have running Clock Nest to continue with the Setup program WARNING This program is protected by copyright iaw and Phematonal teates ot distebution of this program or ary Unauthotived sapoduction portion of map result in severe civil and criminal penalties and wil be prosecuted to the maximum extert possible under law rm cme NOTE The dialog boxes can look a bit different or be omitted depending on the Windows type language version etc that you use Click Next
17. as created see page 18 Status Shows the status of the node The normal status is Config Online 45 Panasonic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 15 12 Operating Instructions TLON Manager V1 2 Channel Shows the Channel the node is installed on Unit no The number given to the node when it was created Description Starts with a number for the unit followed by the Description given in the Create unit dialog box if any Last reset cause Shows the reason for latest restart of the node Transaction timeouts Shows the number of messages sent but not acknowledged by all other nodes in the network The number should be O after the node has been installed The number may increase if new nodes are installed Reset the value and all the others by clicking Reset Transmission errors Must not increase during a 10 minutes interval Test Shall normally be Good Property Use the Edit node dialog box to edit the name number and or description of the node Select a node and double click the right mouse button to get a pop up menu Select Property The following dialog box displays Hame Humber Type Subnet Channel Meuronl D Description Cancel NOTE If the number is changed the program will ask if the node shall be updated If the node is not updated the number in the node and the number in the program will be different
18. bnet 11 E Node_0 E Node_1 wave a Detail Info This command asks a node in the network a series of questions which will be presented in a dialog box There are two ways to get the detailed information a Select a node and double click the right mouse button to get a pop up menu Select Detail Info b Select a node and click Detail Info 44 Panasonic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 Operating Instructions TLON Manager V1 2 Subnet_1_1 E Node_O Sa a Replace af Install Remove Detail Info Move a Control b New unit Save Auto Bind Update all Restart Savaicl Update The following dialog box displays TLON Manager 1 2 Detail Information Node 1 EBLS12 G W512 AAA CAF AE 4D 495000 Config Online s E 000163150200 Channel OOOOOOOO0000 a 0101999995 O TLOWN node software Firmware Version E Last Reset Cauze Watchdog Reset Most Recent Errors Transaction Timeouts Lost Messages Missed Messages Transmission Errors Receive Full The dialog box contains a lot of information and a deeper knowledge of the TLON Network is required to be able to understand some of it The information of interest for the average user 1s explained below In case of no contact the information is No contact with node Name The name given to the node when it was created Type The type given to the node when it w
19. c that you use 1595 Operating Instructions TLON Manager V1 2 MEW00460 i e this document in PDF format 1595SE Swedish document TLON handbok in PDF format Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 The following windows displays not for Windows Vista 2 LonWorks PCLTA 10 20 PCC 10 for Windows 2000 amp XP Copyright 1996 2002 Echelon Corp LonWorks PCLTA 10 20 PCC 10 English Welcome to the Lon works PCLTA 10 20 PCC 10 Setup program It is strongly recommended that you exit all Windows programs before running this Setup program Click Cancel to quit Setup and then close any programs you have running Click Next to continue with the Setup program WARNING This program is protected by copyright law and international treaties Unauthorized reproduction or distribution of this program or any portion of it may result in severe civil and criminal penalties and will be prosecuted to the maximum extent possible under law Cancel Exit F3 Click Next Accept the Software License Agreement 1 e click Yes LonWorks PCLTA 10 20 PCC 10 Setup will install the LonWorks PCLTA 10 20 PCC 10 support files into the following directory You may accept the default directory or modify it using the Browse button Echelon LON LonWorks LonTalk and the Echelon logo are U S registered trademarks of Echelon Corpo
20. d and finally All units updated If one or more nodes failed to be updated the following box displays S Tf the check box is un marked you will have to click OK to continue The time is depending on the number of nodes I5 To check this you can select the EBL512 unit and click Wink The buzzer in the EBL512 unit shall sound for approx one second 22 Panasonic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 16 17 18 Operating Instructions TLON Manager V1 2 Update all result The following nodes failed to be updated Node O Write down the nodes in the list so that you can update the nodes later In this example is only Node_O not updated Click OK All the nodes that were not updated by Update all have now to be manually updated one by one Select the Node_x icon respectively and click the right mouse button to get a pop up menu Click Update When ALL nodes are updated click Save all The Network information will now be saved in each EBL512 unit one by one Some information will be saved in the TLON connection board memory and some in the Main board memory It is highly recommended to restart each EBL512 unit Tn the Status line you will get information regarding which unit is being saved and finally All units saved 23 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Mana
21. e Create unit dialog box 37 Panasonic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 Operating Instructions TLON Manager V1 2 13 Remove xif files From each Project xif files can be removed Select Remove xif in the Network menu A dialog box with a xif file list displays In the list select the xif file to be removed Click OK It will now not be possible to select this type of node in the Create unit dialog box 38 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 14 Remove Everything added to the network i e nodes Channels Routers etc may also be removed NOTE After removing a node you have to do Update all units It is recommended to do so also after removing a Channel or Router 14 1 Nodes There are two ways to remove a node a Select the node to be removed and double click the right mouse button to get a pop up menu Select Remove b Select the node and click Remove y System_xyz ry Subnet_1_1 Node_0 E N odia Wink i Replace Wink Install Move Remove T Control b W Ur Save Und i Auto Bind aa Restart Save all Update You will be asked if the node really shall be removed Click Yes or No 14 2 Channels Select Channel in the Network menu The following dialog box displays TLON Manager 1 2 Create channel Name Channel 2
22. e Service pins JP 3 on the main board An id number will be transmitted and for a second be shown 10 A TLON connection board 1590 is required in each EBL512 unit ll From now on use the same EBL512 unit at all times or another EBL512 unit on the same Channel 12 Tt is situated close to the connector J1 for PC Win512 connection i e below and to the right of the keypad on the EBL512 front 21 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 in the Neuron id field and the type of node EBL512 GW512 will be shown in the Type of node field Since the check box is marked TLON Manager will automatically start binding the node in the database The EBL512 unit Node_0 is now created and installed in the network When the binding process is completed there shall be an EBLS512 unit icon with no red frame around it 14 Do the same for the EBL512 unit Node_1 TLON Manager 1 2 File Network Tools Show Help SE Network status Proect Systeme o Path CAlns System_ sayz he System_xyz a Subret_1_ 1 E Node _O ES Node 1 Detail Info Remove Mew unit Update all Save all 15 In this example are now all nodes installed Click Update all TLON Manager will now re connect and update all the nodes installed in the network In the Status line you will get information regarding which unit node is being update
23. e column Click Install A dialog box Install displays See Installation of Routers below Update Updates the selected router See Update below Change When an existing Router has to be replaced you do not have to add a new Router and install it Yet follow the same procedure as for Install but click Change instead of Install See Installation of Routers below Reset Sends a reset message that will clear some statistics and configuration data Status Select a Router in the Name column Click Status and the status will be shown in the Status column e g Not installed Save A dialog box Install displays TLON Manager 1 2 x Install unit must be attached No Cancel a If you are going to carry out the installation instantly 1 e if you are on site and your PC is connected to an EBL512 unit connected attached to the TLON Network jump to chapter 27 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 Installation of Routers below b If you are going to carry out the installation later 1 e 1f you are in your office click No This is probably the most frequently used alternative when creating a new project The specified Router will be added to the list More Routers can now be added For installation of Routers see the chapter below Cancel Closes the dialog box NOTE In the
24. e added Select the Subnet 1_1 icon and click New unit 4 The following dialog box displays Hame Mumber Type EBLS1 efaiwole Subnet Subret_1_1 ki Channel Channel 1 Description Cancel Name Type a name Normally can the default name Node_n be used Max 14 characters Number The number can be 00 29 1 e CU00 CU29 Normally use the Same number as the node number Type 8 Or click the right mouse button to get a pop up menu select New unit or select Unit in the Network menu 18 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 Depending on what is selected in the Create Project dialog box Import xif and if xif files have been imported see chapter Import xif files page 37 there might be one or more types available Normally only EBL512 GW512 For an EBLS512 unit select EBL512 GW512 Subnet See chapter Planning a Project Channels page 14 Select a subnet In this example select Subnet_1_1 default Channel See chapter Planning a Project Channels page 14 Select a Channel In this example select Channel_1 default Description A description of the node may be written here Max 64 characters divided on three rows 5 Click OK to save the settings and close the dialog box The following dialog box displays TLON Manager 1 2 2 J Install unit mu
25. e to upload data from the TLON Network to TLON Manager 32 Panasonic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 11 7 Operating Instructions TLON Manager V1 2 Copy from disk Used when you want to copy a Project from a disk e g a disk CD made in another PC to the hard disk drive in your PC To open the Project it has to be imported to TLON Manager s common database which you will be asked after the copying Select Copy from disk in the File menu The following dialog box displays dddd wa J system _xyz E drive c Ta Cancel From Select the drive Default is always C Ins selected To In the selected drive select the folder Project to be copied The program chooses the same folder name as the name of the Project and suggests a destination folder You may use the name or change it but it is not recommended to change the destination folder Click OK The selected project will now be copied and after that a dialog box displays TLON Manager 1 2 4 Copying completed Import project To be able to open the Project it has to be imported to TLON Manager s common database You can do it instantly by clicking Yes or later see chapter Import page 31 If you click Yes the following dialog box displays 33 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 11 8 Operating Instructions TLON Manag
26. ed channels subnets and routers have to be created before NW Wizard can be used 1 Select NW Wizard in the File menu The following dialog box displays TLON Manager 1 2 Network Wizard Name No Node_0 jo Type Subnet EBL51 a GWwo5le h Subnet_1_1 w Subnet Channel Add Remove iL Name Type a name Normally the default name Node_n can be used Max 14 characters No Number The number can be 00 29 1 e CUO0 CU29 Normally use the Same number as the node number Type For an EBLS512 unit select EBL512 GW512 Subnet See chapter Planning a Project Channels page 14 2 Fill in select the data for a node Name No Type and Subnet 3 Click Add to add the specified node to the list NOTE The Channel will be automatically added in the list 35 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 To remove a node select the node in the list and click Remove 4 Add all the wanted nodes to the list Here is an example with two EBL512 units Node_O and Node_1l and a Security Management system Node_29 in two Subnets Channels i e there is also a Router in the Project TLON Manager 1 2 Network Wizard Name No Node_2 2 Type Subnet TLONDDE Server Subnet_1_2 Subnet Channel Node_O 0 EBL51 27 Subnet_1_1 Channel Mode EBL5 1 27 Subret_1_1 Channel Node 29 24 TLONDD
27. elve EBL512 units nodes or one Router because the total cable length for a channel can then be two times the normal length c Two or more Routers connected via a Backbone net and up to thirty EBL512 units nodes Make a schematic drawing of the network 1 e a drawing showing all the EBL512 units nodes cables and required Routers The fire alarm system s installation drawings can be useful as well as the planning made with Win512 e g system name control unit numbers cables etc For safety reasons it is recommended to place all the Routers and the backbone net together in a locked cabinet room See also chapter Examples page 53 Channels Subnets The EBL512 units nodes are physically connected to each other via a network cable In the LonWorks vocabulary this is called a Channel Compare with a COM loop and the connected loop units The nodes connected to a Channel can be logically grouped into Subnets Compare with loop unit grouping into zones NOTE In the TLON Network is only one group used Le a group a Channel a Subnet In the TLON Manager window the tree view 1s each Channel Subnet shown as a Subnet only In a network type a there is only one Channel Subnet Le Channel_1 No Channel has to be added 4 e For safety reasons it is recommended not to have more than six nodes in a channel subnet gt A TLON connection board 1590 is required in each EBL512 unit 14 Panaso
28. er V1 2 TLON Manager 1 2 Import project Enter name and directory Ic lc Mns system_por Cancel Write the name and directory Click OK The project will now be imported Copy project Used when you want a copy of an existing Project but with a new name This is useful when a new similar Project is to be created Select Copy project in the File menu The following dialog box displays Select from Project dddd amp System_syz Select the Project to copy Click OK The following dialog box displays TLON Manager 1 4 Create project Mame Fath Networkinterace Import mif Name Enter the name of the new project up to 23 characters Path The path will be automatically created when you write the name Click OK The project will now be copied 34 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 11 9 Operating Instructions TLON Manager V1 2 NW Wizard Creating large projects may be time consuming since the node binding time increases in relation to the number of nodes and is also depending on the PC If a large project shall be created the NW Wizard is a good help Here you can define all nodes before binding them It doesn t make the process faster but the bindings for the whole project are made all at the same time which makes the user free for other activities during the long binding time NOTE The requir
29. ger V1 2 7 Add a Channel Regarding Channels in a TLON Network see chapter Planning a Project Channels page 14 1 Select Channel in the Network menu TLON Manager 1 2 Create channel Hame Channel 2 Channel Name A default name for the next Channel to be added Normally the default name is used but information can be added Type The type used with EBL512 units is TP FT 10 default If a fibre optic network is to be used via Fibre Optic Twisted Pair LonWorks Routers the type is FO 10 Other units may use other types of communication List field A list of the existing Channels in the Project New Adds the next Channel in the Name field e g Channel_2 Remove Removes a selected Channel Save Adds the Channel in the Name field e g Channel_2 to the list Cancel Closes the dialog box when the required number of channels is added NOTE In the TLON Manager window the tree view the Channels are not shown only the Subnets Channel_1l Subnet_1_1 7 E g Channel_2_ Backbone 24 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 8 Subnet Regarding Subnets in a TLON Network see chapter Planning a Project Channels page 14 Normally you do not add any Subnets When you add the required Channels and Routers the Subnets will be automatically added and shown in the tree view E
30. hnology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 Click OK Click Transceiver in the Plug n Play dialog box LON1 Transceiver 7 anscernver i FT 10 Apply Cancel Custom Properties Transcerver type Bit rate Single Ended Raw data Laver 1 timing 08 05 0C 0E OF 5 Bytes Raw data Xcvr params 00 04 00 4 4 00 00 00 00 00 J Bytes Transceiver type shall be FT 10 Click OK in the Plug n Play dialog box If the following displays click Yes Ei LonWorks Plug n Play i The configuration settings hawe changed Do you want to re initialize P the device driver to apply the changes Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 4 Installation of TLON Manager Before installation be sure that no other application is running on your PC Before installation of this version uninstall any other version of TLON Manager First install the PCC 10 drivers and the PCC 10 PCMCIA card see chapter Installation of the LonWorks PCC 10 card page 5 The USB Memory stick contains the PCC 10 drivers the TLON Manager software and documents according to the following tree view lt Removable Disk X gt Installation instructions LonWorks PCC 10 2 Win2000_XP i Release 2 01 i Release 1 06 t WinVista Release 2 03 2 cae TLON Manager User manual
31. lation automatically when SEViICe Message is received Cancel Activate service pin is blinking On the specified Router push the Service button An id number will be transmitted and for a second be shown in the Neuron id field and the type of node will be shown in the Type of node field Since the check box is marked TLON Manager will continue i e to start the binding process The router is now created and installed in the network 5 When the Router is installed click Update If a Router fails to be updated a message will be displayed Click Update again until it is correctly updated 6 When all the Routers are installed the EBL512 units nodes can be installed see chapter Installation of a Project page 2l 2 Tf the check box is un marked you will have to click OK to continue gt The time is depending on the number of nodes 4 To check this you can select the EBL512 unit and click Wink The buzzer in the EBL512 unit shall sound for approx one second 29 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 10 Operating Instructions TLON Manager V1 2 Add a Unit Regarding EBL512 units nodes in a TLON Network see chapter Planning a Project EBL512 units nodes page 14 In the TLON Manager window s tree view select a subnet icon e g Subnet_1_1 and click New unit The following dialog box displays
32. leads have to be used Panasonic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 3 Operating Instructions TLON Manager V1 2 Installation of the LonWorks PCC 10 card 3 1 Installation of the PCC 10 drivers Before installation be sure that no other application is running on your PC The USB Memory stick contains the PCC 10 drivers the TLON Manager software and documents according to the following tree view lt Removable Disk X gt Installation instructions LonWorks PCC 10 Win2000_XP i Release 2 01 i Release 1 06 i WinVista Release 2 03 aoa TLON Manager User manual X E F etc depending on which USB connector you use Put the USB Memory stick in one of your PC s free USB connectors Select the folder and the exe file for your type of Windows e g F LonWoks PCC 10 Win2000_XP Release 2 01 pcx10_20Win exe or F LonWoks PCC 10 WinVista Release 2 03 153 0212 01A_OpenLDV340 exe Double click the file name e g pcex10_20Win exe and the following dialog box displays not for Windows Vista Win ip Self Extractor pex10_ 0Win exe ee This will extract and run the installation files for the SESS onworks PCLT A 20 PCC 10 PCLT 4 10 for windows 2000F Click the Setup button to proceed Cancel About Click Setup NOTE The dialog boxes can look a bit different or be omitted depending on the Windows type language version et
33. nic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 5 2 Operating Instructions TLON Manager V1 2 In a network type b there is one Channel Subnet on each side of the Router i e Channel_1 and Channel 2 Channel_2 has to be added In a network type c there is one Channel Subnet for each Router and one for the Backbone net between the Routers normally Channel_2 i e Channel_1 Channel_2 Channel_3 and so on Required numbers of Channels have to be added How to add Channels to the Project see chapter Add a Channel page 24 Routers After the Channels have been added the Routers have to be added to the Project if it is a type b or c network See chapter Add a Router page 26 Use Channel_2 for the Backbone net NOTE In the TLON Manager window the tree view the Routers are not shown i e no icon and no text EBL512 units nodes After the Channels and the Routers have been added the EBL512 units nodes have to be added to the Project see chapter Add a Unit page 30 Planning Creating a project Here follows a rough overview Create a New Project File New Add required Channel s Network Channel Note the Subnet s will be automatically added when you add the Channel s Add required Router s Network Router Add the nodes Subnet_x_x New unit Normally EBL512 units but a Security Management system can also be added Installation All the data will be d
34. outer Write a name and or a number for the router e g Router 1 Type In a TLON Network is normally the type Learning Router used default but it is also possible to use the type Configured router or the type Repeater Near Far A router must be installed between two channels If there is only one channel in the list field see below required new channels must be created see Channel in the Network menu before any router s can be added A router has connections for one Near channel e g Lon A and one Far channel e g Lon B Select a channel in the drop down list respectively This is the same intelligent hardware set for one of the types Do not use a Repeater which has no intelligence 26 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 Near On the first router the channel where the TLON Manager PC is to be connected Channel_1 On any other router the channel nearest the first router Far On the first router the backbone net channel Channel_2 On any other router the channel on the other side of the router respectively List field A list of the existing Routers in the Project The Subnets will be automatically added for the Channel respectively New Clears the field resets it to the default value Remove Removes the selected router in the Name column Install Select a Router in the Nam
35. ownloaded in the units EBL512 etc Installation order 1 Routers Router Install 2 Nodes Node Install Update all and Save all All network data will be updated and saved in all the units i e all the units will get information about all other units NOTE In EBL512 some data will be saved in the TLON connection board 1590 and some data in the Main board 1556 Wink This is a way to check if a unit is correctly connected and installed in the network 15 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 6 Create a New Project This example will show how to connect two EBL512 units CU00 and CUO1 in a TLON network Start TLON Manager 1 e double click the P onereor icon on your PC s desktop TLON Manager 1 2 Kak Fie Network Tools Show Help Project Path Wi tk Detall Into Remove Hew unit Update all Save all 1 Select New in the File menu TLON Manager sim Network Tools New Open Delete Import Export Copy from disk Copy project A dialog box displays 16 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 TLON Manager 1 2 Create project Mame Path Networkinterace LOW Import xit M EBL5S2 GW512 Securimaster 1 43 connection M TLONDDE Server Name Type a name
36. pears Open Control Panel The host was unable to communicate with the NSI Subsystem NS z Op en LonWorks Plug n Play A 8 Change something click Apply click OK Open LonWorks Plug n Play again and change back to correct settings click Apply click OK For Windows Vista the following is valid Right click the TLON Manager 1 2 icon Me on your Desctop Select Properties Shortcut Advanced Put a check mark in the Run as Administrator checkbox Click OK OK to start TLON Double click the TLON Manager 1 2 icon Manager 1 2 13 Panasonic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 9 Operating Instructions TLON Manager V1 2 Project 5 1 5 1 1 Normally often the network planning is carried out in your office before the installation on site is finished Afterwards during the commissioning the TLON network installation can be performed Naturally the network planning and the installation can be carried out at the same time on site TLON network installation download of the project network data to the network units EBL512 and Routers Planning a Project A TLON Network can consist of two EBL512 units or up to thirty EBL512 units plus a number of Routers connected via a Backbone net In rough outline there are three types of network a Up to six EBL512 units nodes b One Router and up to tw
37. ration Destination Folder C 4Lonworks Browse Cancel It is recommended to use the default path for the LonWorks files Click Next gt The installation process starts Setup Complete Setup is complete ou may configure your PCLTA4 10 20 PCC 10 by first inserting it into your machine allowing the operating system to recognize it then configuring it using the LonWorks Plug n Play Control Panel application Click Finish to complete Setup If you do not want to view the README file un mark the check box and then click Finish to complete the Setup Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 Setup Complete Setup has finished copying files to pour computer In order for the modifications to your system s configuration to take effect you must restart your computer C Yes want to restart my computer now Remove any disks from their drives and then click Finish to complete setup Click OK Shut down the PC power off See next chapter Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 3 2 Installation of the PCC 10 PCMCIA card First install the PCC 10 drivers see chapter Installation of the PCC 10 drivers page 5 e With the PC turned off insert the PCMCIA card PCC 10 into the PCMCIA slot in the PC PCMCIA
38. rk Channel A physical part of the network 1 e the wires to which up to six units nodes are connected Compare with a COM loop and the connected loop units Subnet A logical group of nodes units on a subnet Compare with loop unit grouping into zones Router Repeater Normally a repeater will forward all valid data and a router will forward all valid data based on its destination address It is normally the same unit configured as a repeater or a router In a TLON Network it doesn t matter because all valid data will be forwarded In a TLON Network is grouping not used i e a subnet a channel one group On each side of a Router is a Channel Subnet Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 2 TLON Manager kit 1595 1595SE The kit contains the following Q PCMCIA card PCC 10 Network interface PCMCIA Type H PC Card PCC 10 card cable 1595SE only Patch coupler 1595SE only Cable with flying leads USB Memory stick containing TLON drivers TLON Manager documentation etc F PF 7 The PCC 10 card is connected to the modular RJ45 connector in EBL512 via the PCC 10 card cable NOTE 1595SE only When the card cable is to be connected to an EBL512 with old hardware 1 e a terminal block instead of a modular RJ45 connector the Patch coupler and the Cable with flying
39. s Fire amp Security Technology Europe AB MEWO00460 Rev 4 Operating Instructions TLON Manager V1 2 15 1 Wink 4 15 2 Replace 42 15 3 Install 42 15 4 Remove 42 15 5 Move 42 15 6 Control 42 15 7 Save 42 15 8 Auto Bind 42 15 9 Restart 42 15 9 1 Restart subnet 43 15 9 2 Restart network 43 15 10 Update 44 15 10 1 Update all 44 15 11 Detail Info 44 15 12 Property 46 16 Flowcharts 48 16 1 Create a TLON Network 48 16 2 Network troubleshooting 51 16 3 Network maintenance 52 17 Examples 53 18 Revision history 55 Panasonic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 1 Operating Instructions TLON Manager V1 2 Introduction 1 1 TLON Manager is an installation and maintenance tool for the TLON Network used for the fire alarm system EBL512 This Operating Instruction describes the most common tasks used when installing and maintaining a TLON network It is not a complete description of the TLON Manager Basic knowledge of windows and windows applications is required This document describes how to install the LonWorks drivers the PCMCIA card for a laptop PCMCIA slot and the PC program TLON Manager An example describes how to create and install a Project Definitions PCC 10 card An Echelon card that fits in the PCMCIA slot in the laptop PC PCMCIA Type I PC Card Unit A physical device connected to the network e g an EBL512 unit Node A logical part of the netwo
40. st be attached Na Cancel 6 a If you are going to carry out the installation instantly 1 e if you are on site and your PC is connected to an EBL512 unit connected attached to the TLON Network jump to chapter Installation of a Project page 21 b If you are going to carry out the installation later 1 e if you are in your office click No This is probably the most frequently used alternative when creating a new project 7 TLON Manager starts a binding process After that a new EBLS512 unit Node_0 is added to the Subnet_1_1 icon Channel_1 in the tree view The binding time is depending on the number of nodes in the network 19 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 E TLON Manager 1 2 File Network Tools Show Help S El Network status Project System_xyz EJ Fath C Alns System_sye he System ye y oubnet_1_1 oo E Node O _ wink Beta info L Heme Update all Save all Regarding the red frame around the EBL512 unit Node_0 see below 8 Add the wanted number of EBL512 units nodes the same way In this example add one more unit Node_1 TLON Manager 1 2 File Network Tools Show Help S El Network status Project System xyz Path CAlns System_ sayz se Systemi_xyz Ly Subret_1_ 1 ES Node_O ES Hode 1 Save all The window shows the Project name
41. tallation via Floppy disk has been removed Revision 3 Info revised added or deleted in the following chapters 1 1 1 2 3 1 3 2 4 6 6 1 7 8 9 10 footnote 25 15 11 17 Revision 4 Some Windows Vista information Info revised added or deleted in the following chapters 3143 2 4 55 This page has deliberately been left blank Panasonic Panasonic Electric Works Fire amp Security Technology Europe AB Jungmansgatan 12 SE 211 19 Malm Sweden Tel 46 0 40 697 70 00 e Fax 46 0 40 697 70 99 info fste eu pewg panasonic com www panasonic fire security com ISO 9001 NATIONAL ACCREDITATION OFCERTIFICATION BODIES
42. the node e g EBL512 corresponds to the selected node in the TLON Manager window s tree view A not connected node not installed etc can not receive a wink message There are two ways to send a wink message a Select the node and double click the right mouse button to get a pop up menu Select Wink b Select the node and click Wink SE System_xyz ae Subnet_1_1 ES Node_O m Replace Instal Remove Detairinto ae Remove Control gt New unit save Auto Bind Update all eer Save all Update The wink message turns on the buzzer for approx 1 second in the selected EBL512 unit If TLON Manager can not communicate with the node see the status line the following message displays TLON Manager 1 2 A Cannot communicate with the device Subsystem NS 26 Click OK to close the message box 4 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 15 2 15 3 15 4 15 5 15 6 15 7 15 8 15 9 Operating Instructions TLON Manager V1 2 Replace When the TLON connection board 1590 is replaced in an EBL512 unit select the unit and click Replace After that you have to Update and Save see below Install The unit will be installed in the network see chapter Installation of a Project page 21 and chapter Installation of Routers page 28 Remove The unit will be removed from the project Move A node can be moved
43. u can restart see above all the nodes in a TLON Network Select Restart network in the Network menu The following dialog box displays TLON Manager 1 2 T P j Are you sure Click Yes or No If TLON Manager can not communicate with restart a node see the status line the following message displays TLON Manager 1 2 Click OK to close the message box 43 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 15 10 15 10 1 15 11 Operating Instructions TLON Manager V1 2 Update Normally you update a node i e you download the network configuration data to the physical node after it has been installed see chapter Installation of a Project page 21 Update can also be used when you suspect that the configuration data in a node is incorrect When the TLON connection board 1590 see Replace above and or the Main board 1556 is are replaced in an EBL512 unit you have to update the node Select the node and click the right mouse button to get a pop up menu Select Update If TLON Manager can not update the node the following message displays Error Could not update the node Click OK to close the message box After Update you shall click Save or Save all Update all All the nodes in the network can be updated see above with only one command Click Update all See also chapter Installation of a Project page 21 Su
44. urity Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 17 Examples An example of a network with eight EBL512 units gt six units 1 e a Router is required Channel_1 100R oe oe TaS F i28 can lt SS H HHA TT had a n a Tele lite e Wp 100R 100R E X 4 N 2 Q 53 Panasonic Electric Works Fire amp Security Technology Europe AB MEW00460_ Rev 4 Operating Instructions TLON Manager V1 2 An example of a network with twenty EBL512 units connected via four Routers and a Backbone net 100R in the figure should be 105R 1 1 8W For safety reasons put all routers together ina lockedcabinet room Routers type FT 10 lt gt FT 10 Backbone net Clb nel 1 The SysMik GmbH Universal Router is recommended Keep wires shorter than 1 meter I pe j SS SS SS eS SS ee Channel 2 l Near To ee m m lt mn m mn m al ST Be e depending of type of cable up to 2700 m 54 Panasonic Electric Works Fire amp Security Technology Europe AB MEWO00460 Rev 4 Operating Instructions TLON Manager V1 2 18 Revision history Revision 1 Company name and logotype changed to Panasonic Elucidations and small corrections in the document Chapter 4 Information added red font colour Revision 2 Chapter 3 Drivers for Windows 95 98 have been removed Chapter 4 Ins
Download Pdf Manuals
Related Search