Operating Instructions for Control CS 300 GB
Contents
1. AVE absolute value encoder plug terminal 7 12 C Thermal element in the drive D Manual emergency control emergency crank or emergency chain MFZOVITOR CU aD I 99996999 relay 2 relay 3 relay 4 X10 potential free switch contact Terminal block X5 MFZOVITOR gt Overview of connections i mwaa S 880080808 MFZOV ITOR Terminal block X4 for pneumatic safety edge protection pressure sensor test X4 X3 8 X13 X1 Terminal block X4 for optoelectronic safety edge protection PART OPEN safety edge protection OPTO photoelectric drive through barrier 208000990 OOO DOO Emergency off slack rope switch wicket door contact draw in protection 24V DC 250 mA Terminal block X3 assignment IJI CLOSE switch Sal O impulse switch1 Ba os O OPEN switch OG oS STOP switch JI Impulse button seguence control 10009 impulse button 28000000 OPEN switch CLOSE switch Terminal block X4 for 8 2 kOhm safety edge protection PART OPEN safety edge protection photoelectric drive through barrier OQ OQ 24V DC 250 mA OPEN STOP CLOSE buttons 6 lead solution CLOSE button OPEN button STOP button 2000000000 K2. MFZOVITOR Operating Instructions for Control CS 300 GB CS 300 Gate Controls Rev 5 5 1 p IX ee SY YS MFZOVITOR x 1 Contents General safety instructions Contents 2 Key to symbols 2 General safety instructions 2 Overview of products 3 Initial Operation 5 Programming with the LED module 9 Programming with the LCD monitor 11 Navigator LCD monitor only 12 Overview of functions 14 Error messages and rectification 22 Technical data 23 EU Declaration of Conformity 23 Appendix 24 Danger of personal injury The safety instructions must be observed Warning Danger to property The safety instructions must be observed Information Special information OR Reference to other sources of information Guarantee The function and safety of the equipment is only guaranteed if the warning and safety instructions included in these opera ting instructions are adhered to MFZ Antriebe GmbH Co KG is not liable for any personal injury or damage to property that occurs as a result of the warning and safety instructions being disregarded Using the equipment for its intended purpose The CS 300 controls are designed only for controlling gates and doors with digital end position systems Target group Only qualified and trained electricians may connect programme and service the controls Qualified and trained electricians meet the following requirements knowledge of the general and specific saf
3. safety edge protection photoelectric drive through barrier Safety edge protection OPTO photoelectric 24V D 250 mA drive through barrier 24V DC 250 mA Terminal block X4 for three wire photoelectric barrier 1 sequence control 2 button or selector switch 3 effective in down direction for external switching devices connection to terminals 1 and 2 Three wire photoelectric barrier wt white gr green br brown MFZOVITOR Terminal block X5 potential free switch contact relay 1 relay 2 relay 3 relay 4 ERIS 5 4 Connection examples for command and safety devices terminal block X3 OPEN STOP CLOSE buttons 6 lead solution CLOSE button OPEN button STOP button OOOOOOO O O O OOOOOOOOO OPEN STOP CLOSE buttons 4 lead solution CLOSE button CLOSE button OPEN button STOP button Key switch OPEN CLOSE CLOSE OPEN Impulse button sequence control impulse button Connection t Connect the command and safety devices to the control MFZOVITOR 6 Programming with the LED module GB 6 1 Overview of LED module Key Q upof LED illuminated LED flashing 6 2 LED module mode
4. MOD MOD7 Factory setting 3950 MOD1 50 OFF MOD1 MOD1 MFZOVITOR Function P E BARRIER CLOSED P E BARRIER OPEN SEP LEADING Description MOD1 Stop when activated MOD2 Stop and reverse when activated MOD1 Photoelectric barrier not active MOD2 When the photoelectric barrier is activated between the CLOSED end position and the pre limit switch CLOSE the door stops The red light is on The pre limit switch CLOSE goes automatically to CLOSED end position 4 600 MODI No function MOD2 Leading photoelectric barrier MFZ Explanation of the relay modes A Traffic light functions Setting options MOD 1 MOD 2 MOD 1 MOD 2 MOD 1 MOD 2 Forewarning Flashing Flashing ON Flashing OFF Factory setting MOD 2 MOD 1 MOD 1 Door run ON Flashing ON OFF OFF MOD Description Sedan end Sicil MOD 1 Red traffic light 1 ON OFF OFF MOD 2 Red traffic light 2 ON OFF OFF MOD 3 Red traffic light 3 ON OFF OFF MOD 18 Red traffic light 4 OFF OFF MOD 23 Green traffic light OFF ON depending upon parameter MOD 1 3 RESTING B Position messages MOD Description Remarks MOD 6 OPEN end position MOD 7 CLOSED end position MOD 8 Not OPEN end position MOD 9 Not CLOSED end position MOD 10 Before end position OPEN PART OPEN OPEN MOD 11 Before end position CLOSED The relay closes the contact when the door is in the OPEN end position The relay
5. 80 non condensing Assembling works with less vibration e g at a masonned wall IP 65 about 1 8 kg MFZOVITOR Manufacturer MFZ Antriebe GmbH amp Co Kg Neue Muehle 4 48739 Legden Germany We hereby declare that by virtue of their conceptual development and design as well as their manufacture as we have brought them onto the market the products cited below CS300 Door Controls conform to the relevant basic health and safety regulations of the following EU guidelines and standards EU Construction Products Directive 89 106 EU DIN EN 13241 1 DIN EN 12453 DIN EN 12445 DIN EN 12978 EU Electromagnetic Compatibility Directive 2004 108 EG EN 55014 1 EN 61000 3 2 EN 61000 3 3 EN 61000 6 2 EN 61000 6 3 EU Machinery Directive 2006 42 EG EN 60204 1 EN ISO 12100 1 EU Low Voltage Directive 2006 95 EG EN 60335 1 EN 60335 2 103 BGR 232 Directive for Power driven Windows Doors and Gates Legden 29 December 2009 Manufacturer s signature Hans Joachim Molterer Position of signatory Manager e J MFZOVITOR Amb 0000 Limit switch and safety circuit for drive Wiring allocation AVE absolute value encoder plug Electronic interface The numbers on the plug are also the wire numbers 4 Safety circuit input 5 RS 485 B 6 GND 7 RS485A A AVE plug absolute value encoder plug 8 Safety circuit output B AVE plug terminal absolute value encoder plug 9 12V amp terminal
6. AUTO LEVEL SELF LOCK SU WI Description Setting the before end position switch point for the CLOSE direction MODI Standard assembly clockwise rotating field increasing AVE values during opening run MOD2 Special assembly anticlockwise rotating field increasing AVE values during opening run This setting may only be altered in the case of a special customised drive installation The point where the reversing switch is activated before the CLOSE end position is reached After going beyond the cut out point the door is stopped if the switching strip or photoelectric barrier is activated but it is not reversed The value must not exceed a maximum of 5 cm above the lower end position The power is displayed during the opening movement If the power monitoring facility is activated a value must be set which is lower than the lowest value displayed during opening The larger the difference in comparison to the lowest value displayed the less sensitive the reaction of the power monitoring The power monitoring facility is only activated if the value is set to be gt 0 ON Align with ground ON OFF Align with ground OFF MOD1 Automatic operation MOD2 Manual operation for OPEN and CLOSE MOD3 Manual operation for CLOSE Connection to terminal strip X4 9 10 MOD1 SU WI button 1 When the button is pressed the door opens as far as the intermediate position PART OPEN There is no automatic closing of the door
7. Is 5 HE e A I 5 gt 400v 50Hz wo N PE 18 5 2 4 A 1 Key K1 protection CLOSE K2 protection OPEN M1 motor T1 transformer X1 terminal block for mains connection X2 terminal block for motor X11 sockets for digital end position system with safety circuit STOP CIRCUIT Connection tS Connect the digital end position system to the control tS Connect the control to the mains tS Connect the control to the motor t Short before the corresponding screw terminals groups of cables should be make safe by means of straps Information Technical data see page 23 MFZOVITOR 5 3 Allocation of connections for command Terminal block X4 and safety devices for 8 2 kOhm safety edge protection PART OPEN Command and safety devices can be connected to terminals X3 X4 and X5 Terminal block X3 safety edge protection CLOSE switch photoelectric drive through impulse switch barrier OPEN switch 24V DC 250 mA STOP switch Terminal block X4 emergency off slack rope switch for pneumatic safety edge protection pressure sensor test wicket door contact draw in A 8 2 kOhm resistor must be connected in series protection The input parameter SEP TEST must be switched on PART OPEN Terminal block X4 for optoelectronic safety edge protection PART OPEN
8. OD 5 Remarks The relay is open in the CLOSED end position If an OPEN command is received the relay closes and remains closed until the CLOSED end position is reached again If a time delay is required for opening the magnetic lock this is realised through the parameter DELAY OPEN and forewarning Before every CLOSE command the optoelectronic transmission system is activated and remains active for the duration of the closing run This activation results in a closing run delay of approx 0 5 seconds The relay generates a test signal when the CLOSED end position is reached and expects as a reaction to the test signal that the safety circuit is activated The relay generates a test signal when the OPEN end position is reached and expects as a reaction to the test signal that the switching strip input circuit is activated At every drive command the relay closes for approx 1 second With the aid of this relay an additional starting capacitor that is required for AC applications is switched on in addition to ensure safe starting of the motor At every OPEN command the relay is closed for 2 minutes and can therefore be used to control a light Before every CLOSE command the radio transmission system is activated by an impulse The duration of the activation must be set in the transmission system This activation results in a closing run delay of approx 0 5 seconds The relay is always open MEZOVITOR 9 3 Diagnost
9. ages please refer to section 10 OPEN end position CLOSE end position Final position OPEN denied Final position CLOSED denied Before end position OPEN Before end position CLOSE From before CLOSE position to CLOSE position Magnetic locking function Brake Brake negated Brake remains ON during open time SEP activated Red light 4 flashes during forewarning and is off when door is running From before end position OPEN to OPEN end position Activation of the optoelectronic transmission system Test of draw in protection before opening run additional module required Test of external safety devices before closing run additional module required Green light is on during OPEN end position and OFF during forewarning and OFF when door is running Capacitor circuit for 230V single phase drives Yard light function 2 minutes after OPEN command Activation of radio transmission system Impulse signal after attaining OPEN end position Relay OFF PS testing is active P5 testing is inactive Forewarning also before opening Immediate opening Setting options MOD1 MOD28 MOD1 MOD28 MOD1 MOD28 MOD1 MOD28 ON OFF ON OFF 0 8190 is set to programmed value after adjustment 0 8190 0 8190 Factory setting MODO MOD MOD1 MOD14 OFF OFF 4050 3950 4050 e Mrz MFZOVITOR Function BES CLOSE ROTATING FIELD REVERSE OFF POWER
10. ard for residential commercial and light industrial environments Machinery guidelines EN 60204 1 Safety of machinery electrical equipment of machines part 1 general requirements EN 12100 1 Safety of machinery Basic concepts general principles for design Basic terminology methodology Low voltage EN 60335 1 Household and similar electrical appliances Safety EN 60335 2 103 Particular requirements for drives for gates doors and windows Professional association D BGR 232 Directive for Power driven Windows Doors and Gates MFZOVITOR 4 1 Various options The following package options are available for the CS 300 controls CS 300 control with LCD monitor CS 300 control with LCD monitor in housing CS 300 control with LED module for setting the OPEN and CLOSED door positions further adjustment settings are not possible CS 300 control without LED module and without LCD monitor module or monitor are required for adjusting the settings All the above options can be fitted with a plug in weekly timer and a plug in radio receiver The following options are available for the housing Housing with CS three button input unit Housing with KDT three button input unit Housing with key switch ON OFF Housing with main switch Housing with emergency off switch The operating instructions describe the connection possibili ties and programming procedures for the different mo
11. circuit for door operator X2 B1 B2 Bridge X3 3 4 External stop button X112 Internal stop button The door has travelled beyond one of the end positions The end positions have not been programmed yet The programmed running time has been exceeded The safety edge protection is faulty Safety edge protection was triggered The PS switch is not activated at the CLOSE end position An incorrect rotating field is connected to terminal X1 Communications fault between the end position switch and the controls The power monitoring has been triggered Rectification Check the voltage supply of the drive and the controls Check the rotating field and establish clock wise rotating field if necessary Check and then close the safety circuit Check the programming of the end positions and reset them if necessary Check the path of the door Re programme the running time Check the safety edge protection and the spiral cable Remove obstruction from path of door Check the PS switch spiral cable and profile Check the setting for the CLOSE end position Ensure that a clockwise rotating field is connected Check the cable and socket connections Check that the door can move freely Reset the power value After rectifying the cause of the fault the controls must be disconnected briefly from the mains Dimensions of housing Assembling height Power supply v
12. closes the contact when the door is in the CLOSED end position The relay closes the contact when the door is not in the OPEN end position The relay closes the contact when the door is not in the CLOSED end position The relay closes the contact when the door is in the before end position OPEN PART The relay closes the contact when the door is in the before end position CLOSED MFZOVITOR MOD Description Remarks The relay closes the contact when the door is in the area between the end position CLOSED and the before end position CLOSED The relay closes the contact when the door is in the area between the OPEN end position and the before end position OPEN PART OPEN Remarks MOD 12 Before end position CLOSED to CLOSED end position MOD 19 Before end position OPEN to OPEN end position C Impulse signals MOD Description MOD 4 Impulse when there is an OPEN command MOD 27 Impulse when OPEN end position is reached The relay closes the contact for 1 second when the door receives an OPEN command This impulse can be used to control lights for instance The relay closes the contact for 2 seconds when the door reaches the OPEN end position This impulse can be used for instance to open a following photoelectric barrier Remarks D Brake functions MOD Description MOD 14 Brake MOD 15 Brake negated MOD 16 Brake remains ON during open time The switching contact of the brake rectifiers is activated via th
13. dels CS 300 control with LED board CS 300 control with attached LCD display board Q 4 2 CS 300 basic board MFZ MFZOVITOR with attached LCD display monitor O A ste gt lt m S000000 O gt lt N X6 I xl LI ooo000 gt lt OOOOOlW gt lt R e NO ooy o toc e NO BOM 00 ko c Y Key X1 terminal block mains connection X2 terminal block motor X3 terminal block command devices X4 terminal block safety elements X5 terminal block relay X6 sockets for internal ON OFF switch X7 sockets for internal 3 button input unit X8 socket for monitor under monitor X9 sockets for radio receiver X10 sockets for weekly timer X11 sockets for digital end position system X12 socket for external radio receiver X13 terminal block for CS three button input unit H4 X status display for safety edge protection SEP illuminated when SEP is working H6 Safety circuit status message lights up when the safety circuit is closed MFZOVITOR 5 1 General Warning To guarantee that the equipment functions properly the following points must be ensured The gate or door is installed and ope rational The MFZ drive motor is installed and 5 2 Mains connection Danger To guarantee that the controls function pro perly the following points must be ensured The mains vol
14. e ADJUSTMENT mode the OPEN CLOSED end position settings are adjusted Warning In the ADJUSTMENT mode of operation the drive does not switch off when the end position is reached The door can be damaged if driven beyond the end position Fine adjustments can be made in the INPUT operating mode Display displays the end position value Operating mode 3 INPUT In the INPUT operating mode the values of various parameters can be altered Display displays the selected parameter displays the programmed value status Operating mode 4 DIAGNOSIS In the DIAGNOSIS operating mode door specific checks can be queried Display displays the check displays the checking status MFZOVITOR 9 AA a5 lt pue INdNI 01 u in1 y n eA DALS 9n BA oSeoJ e 9n BA se l1Du 2es d 9n BA 129 99S 235 7 lt nueui uBnoiu1 UMOP 0J2S yas 7 lt G nueui ubnoJui dn jjo45s 25 1 lt C pue passaid Q pioH uonisod 100p aves oes 1 lt pue passaid J pioH uonisod JOOP ALS N3dO dNIJ INdNI N3dO AV I3d LAdNI 1531 d4S LAdNI V AV 14 INdNI AV 13H LAdNI C AV 13d LAdNI L AV 138 LAdNI 315015 ADINO LAdNI ONILSAY LIN LAdNI JINIL GNNOYVNENL LAdNI ONINYVMAYOS LAdNI N3dO JWIL IAdNI AWIL ONINNAY LAdNI HISLNAC LAdNI NMOd IVANVA TIWANVI dN IWANVI TIWANVI ss z lt O
15. e relay to achieve a quicker brake function The contact is closed and the brake released as a result as soon as the door moves zero current brake The switching contact of the brake rectifiers is activated via the relay to achieve a quicker brake function The contact is opened and the brake released as a result as soon as the door moves operating current brake The switching contact of the brake rectifiers is activated via the relay to achieve a quicker brake function The contact is closed and the brake released as a result as soon as the door moves zero current brake To obtain a smoother stop by the door in the upper end position the switching contact is not switched in the OPEN end position OPEN TIME MFZOVITOR E Error messages MOD Description Remarks MOD 5 Error message MOD 17 SEP activated F Functions for external accessories MOD Description MOD 13 Magnetic lock function MOD 20 Activation of optoelectronic transmission system MOD 21 Test of draw in protection MOD 22 Test of external safety devices MOD 24 Capacitor MOD 25 Yard light function MOD 26 Activation of radio transmission system MOD 28 Relay OFF The relay closes the contact when a stop command is given or an error occurs All errors described in section 10 result in activation of the relay The relay opens the contact when the switching strip is activated An error in the switching strip or an unsuccessful test is shown via M
16. ety and accident prevention regulations knowledge of the relevant electrical regulations trained in the use and care of appropriate safety equipment capable of recognising the dangers associated with electricity Instructions for installation and connection The controls must be disconnected trom the electricity sup ply before carrying out electrical works It must be ensured that the electricity supply remains disconnected during the works Local protective regulations must be complied with Regulations and bases for testing For connecting programming and servicing the following regulations must be observed the list is not exhaustive Construction product standards EN 13241 1 Products without fire resistance or smoke control characteristics EN 12445 Safety in use of power operated doors Test methods EN 12453 Safety in use of power operated doors Requirements EN 12978 Safety devices for power operated doors and gates Requirements and test methods Electromagnetic compatibility EN 55014 1 Radio disturbance household appliances EN 61000 3 2 Disturbances in supply systems harmonic currents EN 61000 3 3 Disturbances in supply systems voltage fluctuations EN 61000 6 2 Electromagnetic compatibility EMC Part 6 2 Generic standards Immunity for industrial environments EN 61000 6 3 Electromagnetic compatibility EMC Part 6 3 Generic standards Emission stand
17. ey switch OPEN CLOSE CLOSE 28892808 Internal ON OFF switch X6 55 OQ OQ PART OPEN safety edge protection photoelectric drive through barrier 24V DC 250mA OPEN STOP CLOSE buttons 4 lead solution 2000000000 OPEN switch impulse button GND 24V DC CLOSE button OPEN button STOP button 1 sequence control 2 button or selector switch 3 effective in down direction for external switching devices connection to terminals 1 and 2 A 8 2 kOhm resistor must be connected in series The input parameter SEP TEST must be switched on wt white gr green br brown MFZOVITOR
18. from the position PART OPEN MOD2 SU WI selector switch 1 Closed all OPEN commands lead to the position PART OPEN Open all OPEN commands lead to the position OPEN The door closes automatically from both positions MOD3 SU WI selector switch 2 Closed all OPEN commands lead to the position PART OPEN Open all OPEN commands lead to the position OPEN The door closes automatically only from the position PART OPEN MODA SU WI selector switch 3 Closed all OPEN commands lead to the position PART OPEN Open all OPEN commands lead to the position OPEN The door closes automatically only from the position OPEN MOD5 SU WI button 2 When the button is pressed the door opens as far as the intermediate position PART OPEN Automatic closing of the door also occurs from the position PART OPEN MOD6 Activation of automatic closing Closed no automatic closing of the door Open automatic closing of the door is active MOD External input for clock The door opens once the contact closes and remains in the position OPEN until the contact opens The door then closes automatically This function can be aborted by pressing the CLOSE button The door then closes MOD8 Selector switch Keeping the door open alarm Closed The drive moves the door into the PART OPEN position As long as the contact is closed the door remains there Open normal operation Setting options 0 8190 MOD1 MOD2 10 250 999 ON OFF MOD1 MOD3
19. g the P button t Drive the door into the desired OPEN end position by pressing the button t Save the end position by pressing simultaneously the P button and the button ts Change to AUTOMATIC mode by pressing the P button Setting the CLOSED end position t Change the mode of operation to ADJUSTMENT by pressing the P button t Drive the door into the desired CLOSED end position by pressing the button t Save the end position by pressing simultaneously the P button and the button ts Change to AUTOMATIC mode by pressing the P button 7 1 Overview of the LCD monitor T AUTOMATIC L RESTING Key A mode of operation diagnostic info B parameter diagnostic info C button D button E P button E value status G value status H jumper 7 2 LCD monitor modes of operation The control has four modes of operation with the LCD monitor 1 AUTOMATIC 2 ADJUSTMENT 3 INPUT 4 DIAGNOSIS When the jumper H is pulled the button the button and the P button have no function The display still functions MFZOVITOR Operating mode 1 AUTOMATIC In the AUTOMATIC operating mode the door system is operated Display displays the function being carried out displays any error messages If the self locking parameter is set to MOD2 or MOD3 in the input menu the display changes from AUTOMATIC to MANUAL OPERATION Operating mode 2 ADJUSTMENT In th
20. ia L1 L2 L3 N PE Protection Own consumption of control Control voltage Control inputs Control outputs RS485 A and B Safety chain Emergency shutdown Input safety bar Relays output Temperature range Air humidity Vibrations Type of protection Weight 215 2 5 X 190 vertically at the wall min at a height of 100 mm 400 V 50 60 Hz max power input 2200 W 3 2 N duty cycle 6096 for a maximum running time of 120 s 10 A K characteristic max 250 mA 24 V DC max 250 mA protected by self resetting safety for external sensors 24 V DC all inputs are to be connected free of potential min signal time for incoming control command gt 100 ms 24V DC max 250 mA Only for electronic final switch RS485 level closed with 120 Q all input connections must be potential free if the safety circuit is interrupted no further electrically powered movement of the drive is possible not even in deadman mode For electrical safety bars with 8 2 kO moving loads and dynamic optic systems If inductive loads are switched to e 9 relays or breaks so these must be equipped with corresponding interference measures recovery diode varistores RC modules Operating contact free of potential min 10 mA max 230V AC 4A Contacts used once for power switch are not able to switch mini power anymore Operation 10 C 45 C Storage 25 C 70 C to
21. ic operating mode Display Meaning Status ES OPEN OPEN end position OFF confirmed ON not confirmed ES CLOSE CLOSE end position OFF confirmed ON not confirmed OPEN BUTTON OPEN button ON confirmed OFF not confirmed PART OPEN PART OPEN button X4 9 10 ON confirmed OFF not confirmed CLOSE BUTTON CLOSE button ON confirmed OFF not confirmed SEP Safety edge protection ON system circuit is closed OFF system is interrupted fault IMPULSE Impulse button ON confirmed OFF not confirmed TIMER Weekly timer ON confirmed OFF not confirmed P E BARRIER Photoelectric drive through barrier ON circuit dosed OFF interrupted fault STOP CIRCUIT Stop button of controls ON circuit closed Stop systems of drive OFF interrupted fault CYCLE Gate cycle counter Displays the gate cycles AVE Absolute value encoder Shows the gate position value e MFZOVITOR Fault error message System does not respond Door travels to the CLOSE end position when the OPEN button is pressed Door travels to the OPEN end position when the CLOSE button is pressed STOP ERROR END POSITION ERROR RUN TIME ERROR SEP ERROR SEP TEST ERROR ROT FIELD ERROR RS485 ERROR POWER Cause No voltage supply Rotating field is connected wrongly The safety circuit is interrupted X3 1 2 Emergency off slack rope switch wicket door contact draw in protection X6 1 2 Internal On Off switch X11 4 8 Safety
22. ime is cut short and the door closes immediately after the ON OFF CLOSE photoelectric barrier X4 3 4 has been activated OFF This function is also active if the open time 0 OFF The open time continues as usual MFZOVITOR Function RELAY 1 RELAY 2 RELAY 3 RELAY 4 SEP TEST DELAY OPEN FINE OPEN FINE CLOSE BES OPEN Description All 4 relays can be allocated to a relais mode of 1 28 The parameter M1 3 TRAFFIC LIGHT REST affects the red traffic light MOD 1 3 MOD1 MOD2 MOD3 MOD4 MOD5 MOD6 MOD7 MODS MODS MOD10 MODI 1 MOD12 MOD13 MOD14 MOD15 MOD16 MOD17 MOD18 MOD19 MOD20 MOD21 MOD22 MOD23 MOD24 MOD25 MOD26 MOD27 MOD28 ON OFF The testing of the PS switch takes place in the CLOSE end position To achieve this the airswitch contact must be activated briefly when the door comes to rest on the ground ON OFF Only active when the parameter FOREWARNING TIME is gt 0 Fine adjustment of OPEN end position Fine adjustment of CLOSE end position Setting of cut out point before end position OPEN PART OPEN Red light 1 flashes during forewarning and is on when door is running Red light 2 flashes during forewarning and when door is running Red light 3 is on during forewarning and when door is running Impulse signal at OPEN command Error message In the case of stop messages and error mess
23. o MANUAL OPERATION Display Description MANUAL mE u MANUAL UP The door is driven to the OPEN end position MANUAL mE u MANUAL DOWN The door is driven to the CLOSED end position MANUAL u RESTING The door stands between the end positions When the gate is being driven OPEN the power currently being used is displayed 7 No MFZOVITOR GB 9 2 Input operating mode eo Function Description Setting options Factory setting DEUTSCH Select the menu language DEUTSCH DEUTSCH ENGLISH FRANCAIS ESPANOL NEDERLANDS POLSKI CESKY ITALIANO RUNNING Monitoring the max running time for an open and close movement The running time 1 250 Seconds 60 Seconds TIME must be set to be slightly greater than the effective running time of the door TIME OPEN After the door has opened it runs in the CLOSE direction again after the set time has 0 600 Seconds g elapsed At a setting OPEN TIME gt 0 the impulse function X3 8 9 only generates Auto close off commands in the OPEN direction FOREWARN Before the door starts to move downwards the traffic light flashes during the 0 120 Seconds 0 Off ING forewarning time if automatic closing is activated or in the case of impulse operation TURNA Standing time at every change of direction 0 1 2 0 Seconds 0 3 Seconds ROUND in 1 10 Sec TIME M1 3 MOD1 When resting relay OFF door closed MOD1 MOD1 RESTING MOD2 When resting relay ON door closed MOD2 QUICK ON The open t
24. pue q3SO12 uooq uonisog lt N3dO YOO uonisoq lt ONILSAY INAWLSNIdV ONILSAY JILVINOLRQV LINIDYID dOLS d3ldHV8 J d YJNIL ASINdWII dds MFZOVITOR N3dO LuVd NOLLNG N3dO poui Bunei do JILVINOLRV 01 uinl otq ossz O nueui ubnoJui UMOP 0J2S yes 7 lt SISONSVIQ nueui ubnoJui dn oj3s SEEN 35012 SA NddO 3 S DNIQV31I d3S LAdNI Q3S015 43I44Va d d LAdNI N3dO W3ldHV8 J d INdNI 2201141135 INdNI 13 31 OLNV INdNI 3JdO 354334 INdNI Qq13l4 DNILVLOY INdNI 350193 Sid INdNI N3dO S38 INdNI 35013 JANIS INdNI MFZOVITOR 009 Overview of functions 9 1 Automatic operating mode Display Description AUTOMATIC E i OPENING The door is driven to the OPEN end position AUTOMATIC a U CLOSING The door is driven to the CLOSED end position AUTOMATIC i RESTING The door stands between the end positions AUTOMATIC 0 i RESTING The door stands at the OPEN end position ae The door stands at the position PART OPEN before end position up RESTING AUTOMATIC U i RESTING The door stands at the CLOSED end position ae ue The door stands at the position PART CLOSE before end position down AUTOMATIC r f B RESTING The door stands in the position where the reversing switches off Information If the self locking parameter is set to MOD2 or MOD3 in the input menu the display changes from AUTOMATIC t
25. s of operation With the LED module the controls have two modes of operation 1 AUTOMATIC 2 ADJUSTMENT Information The current mode of operation of the control is shown via the LEDs In the AUTOMATIC mode no LEDs flash In the ADJUSTMENT mode at least one LED flashes Pressing the P button toggles between the modes of operation Operating mode 1 AUTOMATIC In the AUTOMATIC operating mode the door system is operated LED displays H1 H2 Status The door is open The programmed OPEN end position has been reached The door is closed The programmed CLOSED end position has been reached The door is between end positions No end position has been reached e oOo O e e O oO The door has been moved beyond the CLOSED OPEN end position MFZOVITOR 6 Programming with the LED mode Operating mode 2 ADJUSTMENT In the ADJUSTMENT mode the OPEN CLOSED end position settings are adjusted Warning In the ADJUSTMENT mode of operation the drive does not switch off when the end position is reached The door can be damaged if driven beyond the end position LED displays H1 H2 Status The OPEN end position is programmed at this door position The CLOSED end position is programmed at this door position The CLOSED and OPEN end positions are not programmed at this door position 6 3 Setting the end positions Setting the OPEN end position t Change the mode of operation to ADJUSTMENT by pressin
26. tage must correspond to the voltage stated on the type plate The mains voltage must be the same as the voltage of the drive ready for operation For a three phase current a The command and safety devices are clockwise rotating field is required installed and ready for operation For a permanent connection an all pole The control housing with the CS 300 main switch must be used control is installed For a three phase connection only 3 way automatic circuit breakers TOA may be used Information For the installation of the gate door the MFZ drive motor and the command and Warning safety devices the relevant manufacturer S Before switching on the controls for the first instructions are to be adhered to time a check must be carried out after com pleting the wiring to ensure that all the motor connections at the motor and at the controls are securely fixed All control voltage inputs are galvanically isolated from the supply MFZOVITOR Detailed circuit diagram for mains connection and motor 230 V three phase gx M1 Sy OHE aA 5 TT amp E a 7 fs LO 230V 3Phase Po s YT FE 3 s H K1 XI Detailed circuit diagram for mains connection and motor 230 V single phase gar TT 2S E Sil 3 5 V 2 14 6 LO 230V 1 Phase n x N K1 Xi Detailed circuit diagram for mains connection and motor 400 V three phase 2 4 6 I
Download Pdf Manuals
Related Search