InstallatIon manual
Contents
1. INSTALLATION MANUAL SAFERA Smart Stove Guard with power control unit PCU3 SAFERA V4 2 1 ENG SMART PCU3 SAFETY WITH STYLE CONTENTS 1 Preparations 2 Installation 3 Troubleshooting 4 Optional Installing the Water Leakage Sensor Follow these instructions carefully and pay particular attention to the instruc tions marked in the following way A WARNING Follow instructions marked with a warn ing accurately to prevent injury to per sons and damage to property FJ ATTENTION Follow instructions marked with a note carefully to prevent damage to property Hints give you useful advices on using the appliance All electrical connections must be carried WARNINGS Read user and installation manual before using or installing the appliance Install and check the application accord ing to the instructions SAFERA is not li able for any damages or expenses caused by inappropriate installation Check that the Stove Guard is compatible with the cooker see section 1 1 If the network cable is damaged it must be replaced by the service personnel of the manufacturer or their representative to avoid hazards out by a qualified electrician If the appliance was stored in a cold space it must be allowed to warm up to room temperature before connecting it to electric network 1 PREPARATIONS Check the product and the contents of the A WARNING pa2. lock alarm The wireless connection has not been properly made redo the installation starting from step 3 6 The appliance turns off the power from the cooker but the power comes back on immediately If the indicator light for service need is constantly lit the appli ance is faulty Press the OK but ton O to find out the problem type by the indicator lights see on the right Make sure that the Power Control Unit O is con nected correctly in other words the cooker is connected to the OUT cable Blinks once Problem with the radio connection to the Power Control Unit z Blinks twice Power Control Unit O malfunction Blinks three times Power Control Unit O overheated Blinks once Sensor malfunction Blinks twice The service cycle of the extinguisher unit E is full Please contact your vendor or SAF ERA product support l zOl on Blinks three times Power supply D malfunction Blinks once The extinguisher unit is triggered and needs to be re placed Please contact your vendor D j or SAFERA product support Blinks twice The connection of the extinguisher unit is faulty 15 4 INSTALLING THE WATER LEAKAGE SENSOR optional Stove Guard can be equipped with max four SAFERA Water Leakage Sensors The sensors are placed in the typical leakage areas e g under the dishwasher or sink Attach the sensors in place o9
3. Attach the plug of the leakage sensor to the Power Control Unit H If there is an extra sensor its plug is connected to the connector D of the previous sensor Check the operation of the furthest sensor F by placing a damp paper towel against it for 15 seconds When the water is detected the Central Unit gives a sound signal and the warning light for water leakage is blinking Reset the leakage alarm by pressing the OK button Clean and dry the sensor If the sensor is left wet the appliance will give another alarm in an hour after sign ing off the previous one 16
4. ckage before installation Please contact your vendor if you notice anything unusual about the appliance e Central Unit pre installed into a cooker hood Power Supply Power Control Unit Extinguishing Unit E optional User and installation manual Declaration of Conformity SS a nm 0000 T a Sensor 2 1 Compatibility SAFERA cooker guard is compatible with most electrical cookers hobs and ovens meant for household use Traditional cast iron cookers and hobs Ceramic cookers and hobs Induction cookers and hobs Cookers and hobs equipped with a timer afterheat indicator child proof lock or integrated switch off system SAFERA Smart is compatible with cookers no wider than 90 cm see installation step 1 6 Nozzle 2 2 Control Panel Q Child proof lock button OK button O Indicator light for child proof lock Indicator light for normal activity O Warning light for cooktop hazard Warning light for cooktop fire optional Warning light for water leakage Adjustment mode button Indicator light for service need INSTALLATION STEP 1 6 Mount the Central Unit Install the cooker hood with Central Unit according to the dimensions below even if they differ from the instructions of the hood With optional extinguisher Width unit Align the Central Unit Cooker Installation 15 mm wi
5. e turn off the cooker With induction cooker use a compat ible dish o9 Check that the indicator light for normal activity O blinks every five seconds INSTALLATION STEP 5 6 Adjust the alarm limit Check the closest recom mended alarm limit from the reference table on the right The range is 1 12 1 reacts fastest 12 reacts slowest Location of the Installation Alarm Limit Cooker Height 1 12 In a corner 75cm 6 O 65 cm 7 55 cm 8 45 cm 9 Next to a wall 75cm 5 O 65cm 6 55cm 7 45cm 8 In an island 75cm 4 65 cm 5 e 55 cm 6 45 cm 7 Default Adjust the alarm limit according to the reference table above The default alarm limit is 6 First go to the adjustment mode Press the adjustment mode button Q The indicator light for normal activity O lights up amp Then adjust the alarm limit 12 11 Raise the alarm 10 t limit 1 press the OK button O 8 ES 7 6 default 5 4 Lower the alarm 3 i limit 1 press the 2 lock button 4 1 12 When you adjust the alarm limit the new alarm limit is indicated as shown in the table on the right You may check the alarm limit by pressing the adjustment mode button twice Warning lights Number of Alarm Limit beeps eee ecco 12 eee oo 11 eco o 10 pg an eco 9 Red eo 8 e 7
6. eec ccc 6 default eoe oo 5 OK eec e 4 xs Green aoe ee 2 e 1 A WARNING Do not set the alarm limit higher than 9 during the installation If the alarm limit is set too high the appli ance may fail to detect a hazardous situ ation in time 13 INSTALLATION STEP 6 6 check list READY Check the working order of the appliance and fill in the installation checklist All the burners of the cooker cause a child proof lock alarm The oven if connected causes the child proof lock alarm The sound signal is lower than the signal from the cooker child proof lock The child proof lock turns off the oven and all the burners The indicator light for service need is not lit after installation The alarm limit is set according to the cooker loca tion Installation date Installation place Installer 14 3 INSTALLATION TROUBLESHOOTING Problem Remedy Installation is not proceeding as expected You can re start the installation process anytime by pressing the adjustment mode button O for five seconds until you hear the signal and continue from step 3 6 The central unit is not respond ing to any button and none of the indicator lights are lit Ensure that the power supply D is connected cor rectly to the wall socket and that the socket has power None of the cooker plates cause a child proof
7. n step 1 with some of the cooker hood models the extinguishing unit brack et is pre installed in a factory in that case start the mounting from step 2 INSTALLATION STEP 2 6 Mount the Power Control Unit Install the Power Control Unit PCU3 PE L N 230V 16A L2 Max oov 10A A 230V 16A MAX 400V 10A MICRO DISCONNECTION L3 N L1 Max ovio T L L L A WARNING Make sure that there is no power supply to the cooker and the oven by removing their fuses Also ensure that the cooker is switched off OUT wires are always energized when the power control unit is connected to the elec trical network If a wire is loose it must be properly covered If the element voltage of the cooker is 400 V the fuse can only be maximum of 10 A If the element is 230 V the fuse can only be maximum of 16 A Do not install the Power Control Unit to excessive heat Operational ambient tem perature is 5 40 C mN ATTENTION Power Control Unit requires a neutral wire to operate Install the power control unit so that it is not exposed to moisture Check that all cables can move freely m HINT If you are replacing a cooker press the adjustment mode button for five sec onds until you hear a signal Continue the installation according to step 3 6 Installation Mount the Power Control Unit on the wall behind the cooker or i
8. nto the cabinet next to the cooker o9 Couple the protective earth first PE e Couple the other wires o Don t reconnect the power to the cooker yet IN 5x2 5mm 0 7 m d Optional water sen sor connection See chapter 4 OUT 5x2 mm 1 3m INSTALLATION STEP 3 6 Set up the wireless connection Connect the power supply D to the Central Unit Press the adjustment mode button Q indicator lights O O and 9 start blinking by turns Put back the fuses for the cooker and the oven The Power Control Unit O will now contact the Central Unit which gives a sound signal eee You can re start the installation process anytime by pressing the adjustment mode button for five seconds until you hear the signal INSTALLATION s STEP 4 6 Calibrate the system When the indicator lights for child proof lock and normal activity E and Q start blinking by turns calibrate the cooker Choose from the two options OPTION 1 or Cooker and oven are connected to the Power Control Unit OPTION 2 Only cooktop is connected to the Power Control Unit Turn on the oven and press the child proof lock button When you hear a sound signal eee turn off the oven Turn on the biggest cooker plate with maximum power and press the OK button When you hear a sound signal ee
9. th the cen width Height tre of the cooktop Max 60 cm 50 60cm 60 70cm Without extinguishing unit Cooker Installation width Height Max 60cm 45 75cm Depth 60 90cm 60 75cm Align the sensor of Cen tral Unit white lens 100 mm with the cen tre of the cooktop A WARNING The extinguishing area is approx 60 cm in The Central Unit is plugged into the diameter when the installation height is wall socket with its own power supply D in accordance with the table The installa tion height has an effect on the size of the extinguishing area and the extinguishing capacity INSTALLATION 5 OPTIONAL Install the Extinguisher unit A WARNING Install extinguishing unit on top of the cooker hood according to the figures be Make sure that the hose is not squeezed low either A or B and steps 1 6 on the after the installation Minimum radius for figures on the right the hose is 50 mm Highest allowed operation temperatre for extinguishing unit is 50 C Option With some of the cooker hood models the extinguishing unit is preinstalled in the factory in that case ensure that the hose and the cable are properly connected Service and replacement of the extin guishing unit may only be done by ser vice authorized by SAFERA Max T lt 50 C Min R gt 50mm Notice i
Download Pdf Manuals
Related Search