User guide, English OneRemote beeLINK2 controller operates: LG
Contents
1. Devices IR receiver It must be placed so the IR receiver in the device is able to see the emitted light from the IR emitter The beeLINK2 controller can be placed by the device or in another room IR emitters are available in lengths of 1 5 and 10 meters Additional extension cords can be used An IR emitter can be extended to more than 50 meters The IR emitter can be placed inside the device if you want to avoid having it on the outside as long as the IR receiver is able to see the light from the emitter This requires that the device is opened and the emitter is placed inside A beeBUS CATS cable may exceed more than 75 meters without additional amplifiers one gt remote beeLINK2 connections IR sense Prog switch Do not use LED The IR sense socket is output for the IR emitter that sends IR to the device to be oper ated In some cases this socket is also used for sensing purposes Sometimes the Bee LINK2 controller needs to know if the device is powered up or not In some cases this socket is used for other serial communications like RS 232 instead of IR control Prog switch is a push button that must be activated to initiate a programming se quence as described in the option programming chapters Do not use socket is for firmware updating of the controller and connection to special adapters If used for anything else the controller will be damaged LED indicates different operating states Red gr2. and a standard cable that any installer are familiar with Also it is well suited for data transmission Finally many modern house installations use the same connectors making installation even easier Note A BeeLINK bus must ONLY be connected to other beeLINK components If connected to LAN or other systems there is a great risk to damage these systems one gt remote The BeeLINK bus is a parallel bus type Passive splitters therefore can be used to make a network of any shape If many controllers or very long cables are used it might be necessary to add more power supplies Using this parallel structure each beeLINK controller receives the IR data simultane ously Every controller has its own microcomputer living its own life Although some of the controllers can talk to each other most controllers operate fully on their own beeLINK gt installation The beeLINK2 controller gets its power supply and control data via the CATS cable from a beeLINK amplifier The beeBus Once connected to the beeBUS the beeLINK2 controller only needs an IR emitter to operate the device it has been designed for The IR emitter emits the same IR data as the device s own remote control Emitted IR data is in fact only light at a frequency just out of the spectrum that the human eye is able to see It emits short flashes of light a bit like when sending Morse codes using a flashlight The emitter must be stuck on the device nearby the
3. CDV AMEM AMEM2 For compatibility with older remote controls a typical OneRemote layout uses the fol lowing buttons Beolink 1000 Typical BeeLINK use Back Backup e t c EPG Guide e t c EXIT WC Menu Ca Manual power one gt remote beeLINK2 TV source option The BeeLINK active option sets which source button on the remote control that makes the BeeLINK2 go active and turns on the TV as described in the previous chapter The BeeLINK source option combines other source buttons on the remote control with the input sockets on the TV The source option can force the TV to open a specific in put when an AV source is selected LG TVs can have up to 9 selectable sources as shown in this table 0 No new source 1 AVI 2 AV2 3 AV3 4 AV4 5 AVS 6 RGB PC 7 RGB Multimedia 8 Component 9 DVI HDMI Source buttons on beo4 like ML E ESO can be programmed to select one of these inputs Here are some programming examples An option programming sequence is started by pressing the little red switch on the Bee LINK controller until its LED starts flashing Then the 3 code option must be entered with the B amp O remote control Here some examples Beo4 Source Volume Action WR a gt selects HDMI 1 on the TV No volume regulation on TV WE gt selects HDMI 2 on the TV No volume regulation on TV WR WER gt selects HDMI 1 on the TV Volume regulation on TV WE WO gt selects HDMI 2 on the TV No volume regulation on T
4. User guide type 34016136 BEE2 000 000 00000 0000 0000 LE ee BODO e gouged DH e User guide English OneRemote beeLINK2 controller operates LG Flat screen TVs all models ayoOWwsasgauo one gt remote Beo4 Beo5 Translation table Daily operations Playback operations Power 2 Play press 1 sec Stop S OK enter 2 Pause D gt P a gt gt RewFF WW ia P n 4 Guide g zi Return Other operations MENU Menu CR List f gt RH Simplink EZIN V e Input TEXT P SS FAV Go info Special alternative operations gt mm Play gt RE Netcast gt Rm AV mode Co O view Daw O menu As the direct function of the coloured function om Power buttons has been assigned to other functions SS E TV Radio these have to be preceded with a b v Ratio retrieve the actual coloured function Ki The up down arrow operation can be ex changed with the blue yellow buttons See page S Green function Yellow function SS Red function Blue function one gt remote Congratulations The beeLINK2 controller from www oneremote dk can fully operate your TV using your Bang amp Olufsen remote control terminal via a beeLINK system bus Beo4 or Beo5 remote controls can be used Beolink 1000 can be used with reduced functionality This guide explains how This beeLINK2 controller is ready for use plug amp play See the opposite page regarding daily operation Some
5. V WER RO gt selects Component on the TV No volume regulation on TV EZ E RN gt M selects Input on the TV No volume regulation on TV 10 one gt remote beeLINK2 active option As all controllers on the beeLINK bus are receiving all the IR data simultaneously every controller must know when to go active and when to go inactive Sometimes two or more controllers are active at the same time A beeLINK2 controller is used to operate a TV a satellite receiver a DVD player a projector or similar devic es Each controller is specifically made for one device Many devices can be operated this way This is useful when you have more than one device of the same type or simply run out of source buttons When the beeLINK2 controller goes active its LED will turn red to indicate this When another source is selected the controller will go inactive and the LED turn green As a controller goes active it will usually turn on the device if it is not already turned on Setup with 3 receivers and a PS3 playstation attached to both a TV and a projector An example of operation could be Operate projector Operate TV WR Operate DVB S Operate DVB T Operate DVB C DTV Operate PS3 E g a zi 3 NON BANG amp OLUFSEN TV If the HDMI switch in the example is a beeLINK operated type it will automatically switch to the last chosen source 11 Made in Denmark by www oneremote dk 34016136uluk ajoWwa1
6. auo
7. een flash No data has been received since power has been applied Red flash The controller is in option programming mode Red The controller is active Green The controller is inactive Short off When the controller sends data the LED turns off 1 sec one gt remote Operating with OneRemote OneRemote environment To be able to operate the device optimal with the Beo4 the user has to be familiar with operations with the original remote control as described in the device s user manual The beo4 remote control is not equipped with as many keys as most other brands are using We have designed a layout that works logically even when shifting between different OneRemote operated devices To get a common layout for many devices we therefore needed to redefine a few of the beo4 buttons to other functions Coloured function buttons To make room for easy access to more important functions we have moved the col oured buttons to a lower layer To send a color command from the device s original RCU a amp must be pressed before the coloured button This way we are able to assign other functions to the coloured buttons in direct mode In a OneRemote environment the coloured buttons are assigned to these operations a Guide EPG or similar o Back Backup Return or similar y d Programme zapping P P Channel up down or CH CH Programme stepping up down manoeuvring in menus Most set top boxes or TV
8. operations can be altered to improve interaction with other controllers or to your convenience Refer to the installa tion section further on if changes are needed List of Contents Beo4 BeoS Translation beeLINK basics beeLINK2 installation beeLINK2 connections Operation with OneRemote OneRemote environment Beolink 1000 Option programming table Min Programme zapping Option Menu button option Power off option beeLINK2 active option page page page page page page page page page page page one gt remote WE A Mu one gt remote beeLINK basics The IR data emitted from a Bang amp Olufsen remote control is captured with a IR receiver If there is already one IR receiver in the room this can also be used to feed the BeeLINK bus There is no need for two IR receivers in the same room Data received by the IR receiver is fed to a OneRemote Link Amplifier with built in power supply and 5 outputs for beeLINK devices If there is more than 5 beeLINK devices in the setup splitters can be added The BeeLINK bus distributes the IR data received with the attached IR receiver from a Beolink 1000 Beo4 or Beo5 to any number of beeLINK controllers It also supplies the attached controllers with power The cable used between the link amplifier and the controllers is simple CATS type ca ble with RJ45 plugs This type of cable is inexpensive
9. s has 4 arrow buttons for moving up down left and right in on screen menus In addition they have separate programme stepping buttons for zap ping through programmes B amp O remote controls does not have separate buttons for programme zapping We therefore have chosen the blue and the yellow buttons to func tion as programme stepping buttons in direct mode The four up down left and right buttons have been assigned for manoeuvring in on screen menus in our basic setup It is possible to use the up and down arrow for programme stepping refer to the option section page 6 Go or Stop shifted operation Some of the buttons has 2 or three functions To get to these they have to be preceded with or The buttons that has been assigned secondary functions on this controller can be seen in the operating table on page 2 one gt remote Beolink 1000 and Beo4 Beo5 Beolink 1000 and other early Bang amp Olufsen remote controls are not equipped with the coloured function buttons that have been added to Beo4 and Beo5 Some opera tions therefore might be less logical or in some cases not available when using older remote controls in a beeLINK setup Some buttons on the Beolink 1000 remote controls do actually send the same com mands as differently named buttons on a Beo4 Beo5 Other buttons simply has been renamed but still sends the same commands Beolink 1000 Compares to Beo4 Beo5 a H A v g SS VTAPE2 VMEM2 DVD2 DTV
Download Pdf Manuals
Related Search