BCP-7000 User's Manual
Contents
1. 4 2 Communication You can configure your terminal and perform data management via the bundled cradle Uploading You can upload the data collected by your terminal unit to your PC You may hear a beep sound when the terminal is placed onto the cradle When uploading the data to your PC the terminal would show Uploading on the display and the GREEN LED will light on When the task of uploading is completed the message would disappear and the GREEN LED will light off Downloading You can download the data from your terminal unit to your PC Place your terminal onto the cradle and you may hear a beep sound when the terminal is properly placed When downloading the data to your terminal the terminal would show Downloading on the display and the GREEN LED will light on When the task of downloading is completed the message would disappear and the GREEN LED will light off 5 Getting Started 5 1 Turn On Press and hold the power key for over 1 5 second to turn on the terminal The terminal might give a beep sound if the SETTING item Key Click is set to on 5 2 Turn Off Press and hold the power key for over 1 5 second to turn off the terminal The terminal might give a beep sound if the SETTING item Key Click is set to on 5 3 MAIN MENU For the first time use when turn on the termtinal the MAIN MENU would appear at the display 1 Collect Figure 5 3 Note Press the numbe2. Empl ID Location Item No ltem Qty are all PROMPTs User has to download the tysso apg to the BCP 8000 20 7 1 Collecting data Press 1 key to enable the collect function at MAIN MENU Figure 7 1 1 Use Arrow Up Down keys to move the cursor to Check Stock and press ENTER key Check Stock Figure 7 1 2 Input the number 100 and press ENTER key Figure 7 1 3 21 Input data to the fields The sequnce of the data input is from Location gt Item No gt Item gt Qty gt Location Figure 7 1 4 When ESC key is pressed the figure 7 1 5 would appear at the display Figure 7 1 5 When ESC key is pressed exit the menu and the figure 7 1 2 appears again at the display Select Exit to quit the menu sh PE F AAC CA i Figure 7 1 2 22 7 2 Lookup When user repeats the procedure of 7 1 4 user may trigger off the lookup function when the Item No data matches the lookup file data Follow the steps to produce the lookup function at 7 1 4 figure e Location Shijr Input Shijr and press DOWN or ENTER key e Item No 60001 Input 60001 and press DWON or ENTER key The terminal would search the LOOKUP file checking if there is a matched data If there is a mateched data then the terminal would bring all the information of the matched data to the display figure 7 2 1 If there is no matched data
3. cursor would go to next field e item Input data and press DOWN or ENTER key e Qty Input data and press ENTER key e Location e item No Figure 7 2 1 Note You can move the cursor by using Arrow Up Down keys to locate the contents to be changed 23 7 3 Browse The browse function provides nevigation edit or delete collected data Press 3 key to enable the browse function at MAIN MENU In sequence the last saved record would be appeared at the display The last saved record as shown figure 7 3 2 would appear at the display You can use Arrow Up Down keys to navigate all the data or press FN 1 or FN 2 Keys to edit or delete the data figure 7 3 3 Figure 7 3 2 Figure 7 3 3 24
4. Enter This key is for data enter confirmation or execution command O Power The toggle key to shift between power on or power off To avoid an accidental press it requires pressing it for over 1 5 sec to activate the terminal to power on or off Function The key has to associate with another numeric key to activate the functions Please refer to Section 2 2 FN Key Numeric Key for further information Escape Exit or purge the current operation and back to previous operation menu 2 2 FN Key Numeric Key Fn 0 Backlight Switch When operating under a low light environment press FN key then press 0 key it would turn on the LCD backlight so as to acquire better images Press Fn key then press 0 key again to turn off the backlight 2 3 Numeric and Alphabetic Keys 1 ABC abc 2 DEF def 3 GHI ghi 5 MNO mno 6 PQR par 7 STU stu 8 VWX vwx 9 YZ yz Numeric 1 or Alpha A B C or a b c Numeric 2 or Alpha D E F or d e f Numeric 3 or Alpha G H or g h i Numeric 4 or Alpha J K L or j k l Numeric 5 or Alpha M N O or m n o Numeric 6 or Alpha P Q R or p q r Numeric 7 or Alpha S T U or s t u Numeric 8 or Alpha V W X or v w x Numeric 9 or Alpha Y Z or symbol or y z or Numeric or Symbol Q g Numeric 0 or Symbol 3 Connecting to Your PC BCP 8000 can easily perfor
5. BCP 8000 Data Collector TYSSO Ver 1 2011 02 Contents T INTO Os 1 A ae te eet R tae se ne ee CO O caret tate cee tole crea O 1 As AN EGAN A A A ener are DEE 1 RO O A 2 A AG POR O 3 ZOE FUNCION K OY eo o eo REJ OE EEEE CA AE eee 3 22 IN KEV FP INUIMONC KEY eco uses cence 3 2 2 NuMmelie and Alb Mabelie KEYS le eer la 4 3 Battery Care dia 5 OT A dO AT dE d dn eer eee 5 3 1 1 Recharge by the cradle with USB interface Cable oooocccccccccononncccnnccnnnnannccnnnnnnnnnananennnnnnos 5 3 1 2 Recharge by the cradle with RS 232 interface cable oc cooonncccccooncconcccoononncononncnncnnnanonnnnnnns 6 3 143 LOW Battery Wanda aa ii 6 SALA e A e oo 7 3 55 Replace Balley cn it tl 7 A COMMUNICATION UHN iset aa GA GLOW R dE Oc 8 4 1 Installing cradle with USB interface cable oooccccncccccconncconnccnononnncnnnnnonnnonnnnnnnononnnannnnnnnonnnnnanenons 8 A 25COMMUNICAUO zana e E 9 Ds GEL SlAN A a Oda kc OE dE OEG od w 10 012 TUNOMS TEZ OUN A M WOLE 10 SZ AKON z Rad a ta if ta niania a 10 Ho Male eras aa adria 10 O A A TA AEA PEE E A ta pa A 002 SASA 11 A A ba OOO OR ak GT 11 dd BIOWS O aida 12 O A A Pe ney ee eee een ee ee ae re eee eee eee 13 A A A 13 52 0 BO A en O CES O o R A ee ere re eee 18 A ta 19 A e TATE e E eee en eee ee eee one 19 6 2 Memory Near Full warning ccccsssccccesseeeceeseecceseecseuseecsaueeeceageeeceueeeesaueeessaseeeseuseeesaseessneesssags 19 O32 MEMOWEUNWAMINJ s
6. ctile 21 keys keypad provides works of barcode scan data key in editing and navigation comfortably Great sharp LCD with backlight furnishes clear and pleasant viewing A capacious memory furnishes a large amount of data storage 1 2 Unpack Standard Package e BCP unit x 1 Cradle with USB interface for recharge and communication x 1 CD disk contains with BCP 8000 User s Manual and BCP 8000 Job Generator Utility Operation Manual and example Job Application file x 1 Options o Cradle with RS 232 interface for recharge communication cable Power adapter 110V or 220V for cradle with RS 232 interface Note The contents may vary with different options x If there s any physical damage or missing parts please contact your supplier immediately Please keep all packing material and items as they were as the product may be send back terminal for service 1 3 Overview Bl HER ip E lela PEREHI TIE SIDE VIEW REAR VIEW FRONT VIEW SIDE VIEW REAR VIEW FRONT VIEW 2 Keypad The terminal equips with 21 rubber keys All the keys details functions are described at Section 2 1 2 2 and 2 3 2 1 Function Keys SCAN Scan Press to scan a barcode Down Press to cursor down Up Press to cursor up LP yz Alpha The toggle key to shift between Alphabet Upper Case Lower Z A Case and Numeric modes Back Space The back space key Space The space key wg
7. d do tido 19 TEKIN DIC A A A einen E tinier eines 20 TC OEC ic Fe gt Deere meee ea eR a a 21 12 LOOK Did pi od AN OTS A AN EE o Aa 23 WoD VOW SO ei OE A OE EO RJ dO lea herd ite hace A W EA 24 1 Introduction BCP 8000 is a battery operated portable data collector with lookup function Equipped with high quality laser engine it is easy and fast to acquire accurate barcode data The ergonomic built body offers comfortable grab to guaranty BCP 8000 ideal for long time work The vividly bright LCD display tactile keypad 21 key and small foot print cradle furnish convenient operations and data processing key in editing navigation communication and battery charging In addition BCP 8000 provides a very user friendly job generator utility You need not create applications by writing the program source code anymore With the aid of Job Generator you may convert incomprehensible development process to simple steps and configurations and makes data collecting works become distinct and effortlessly BCP 8000 is an ideal device for various data collecting applications such as warehouse management shop floor management asset tracking etc 1 1 Features Job Generator offers users to design their own application easilly High quality laser engine equipped makes barcode reading aggressively The big capacity rechargeable battery endures long working time A cradle offers communication and recharge via RS 232 or USB cables A ta
8. detected hardware Insert the bundled Utility Driver CD disk into an available CDROM on your PC Specify the path to the USB Driver folder and complete the driver installation You only need to install the device once USB driver will automatically assign a virtual serial port recommended for communications You can manually assign the COM Port Enter the advance menu of the device for advanced configurations Execute Start gt Control Panel gt System gt Hardware gt Device Manager gt Ports Com amp LPT will lead you to identify the port number i T i 3 lt eter H ortor A LI ji A ernie Larrea rl Compilar rra Hd ar o dl WTA D r The Ada Haro ieee halpa poa all harda ocho H a ire iO Y zi NI i z PA 3 a P The Dance Martti kata all the Pacha darii mra gt On Po a Lies this DA hl APA fo APTA Cees Od A oe G Device Manager gS Ox Fie Arton View Help NFS E A XXW Gi Human Interface Dowicoe 2 IDE ATA ATAPI controllars m Keyboards Mice and other pointing devices BY Network adapters a Other devices 9 Ports COM amp LPT 7 Corrmunications Port COMIT JY Corrmunications Port CO2 JY Corr munications Port COM 2 Cor munications Port COM Communications Port CO5 4 Communications Port COMES Y Printer Port LPT1 4 Fa ay A Z eI Processors Sound video and game controllers La z 4 System devices Ob miuapasi Cawial Gein aaniraliana
9. m data management unit configuration and battery charge via the bundled cradle The battery supplied in each terminal unit has been partially charged at the factory It is recommended to charge the battery before first use You can install the terminal unit to the bundled cradle and charges the battery either from USB or RS 232 interface cable 3 1 Connecting to Your PC and Charging the Battery 3 1 1 Connecting to PC by the cradle with USB interface cable REDLED pz Jl IPS A BATTERY SYMBOL ma J P a i ZY y S mw q SY A AL A USB Connector Connect the USB interface cable to the USB port on the PC The ORANGE power LED in front of the cradle would be lighted The cradle is ready for recharging the battery or terminal configuration Place the terminal onto the cradle You may hear a beep sound when the terminal is placed onto the cradle if the SETTING item Key Click is set to Enable e There is a LED indicator on the top of the terminal and lit RED In the Display of the terminal there is a battery status icon indicates the battery status e As the battery is being charged the battery status icon is varying and indicates the battery is charging It takes approximately 6 hours to charge from low battery status When the battery is charged completely the battery status icon will turn to static and indicated the battery is full dark icon The terminal RED LED turns off g
10. m lookup file is defined to 3 files figure 5 3 6 5 6 User ID This item provides the function of downloading the user ID file 1 Lookup File Figure 5 3 6 5 18 6 Memory 6 1 Memory Arrangement The terminal is equipped with 2MB SRAM and it is divided into two portions with 1MB each for data and look up file storages A record is composed of FORM s or and MENU s Each record can contain upto 10 FORM s or and MENU s Each FORM can store upto 400 digits and each MENU can store upto 176 digits The 1MB data storage memory can store maximum amount of record number upto 35000 recrods based on the presumption of each record contains with 30 digits The more digit contains in record the less record number is stored 6 2 Memory Near Full Warning When the terminal s memory capacity reaches to less than 5 of 1 mega byte of the data storage portion A warning of Memory Near Full would appear on the display figure 6 2 To accentuate the user aware of memory status it is designed blocking any actions on the terminal without removing the warning by press ESC key Figure 6 2 Figure 6 3 6 3 Memory Full Warning When the terminal s memory is full a warning of Memory Full would appear on the display figure 6 3 It would emit 5 beeps for every barcode scan or any ENTER key is pressed and no save command is executed Only by press ESC key to exit this 19 7 Example The e
11. n be set This is the time span to display the collected record number once the data file is saved to PC 3 Date amp Time Set the correct Date Time yyyy mm dd hh mm ss Figure 5 3 5 2 3 4 Power On This ttem is for defining which display window would be appeared when turns terminal on If 1 Resume is set whenever the terminal turns on the last display window before terminal turns off would appear If 2 Restart is set whenever the terminal turns on the MAIN MENU would appear 5 Auto Off The span between 00 99 minute can be set to turn off the terminal if there is no action taken in the setting time 6 Backlight The span between 00 99 second can be set to turn off the LCD display if there is no action taken in the setting time 7 Key Click To enable or disable the click sound while the terminal works 8 Deletion The item provides the deletion of the collected data by manually or by automatically after data file upload to PC 15 5 3 5 3 Reader This item provides a test function to read barcodes Press SCAN button a red scan light beam will be emitted for the safety reason please DO NOT stare at aperture directly where the light come from A beep with a flashing GREEN LED indicates a successful scan If the scan button is pressed for over 2 seconds and the reading is not successful the red scan light will turn off Press the SCAN button and aim at the barcode to scan it again Fig
12. r key 1 6 or Arrow Up Down keys to move the cursor to locate the selected item Press ENTER key to enable the selected item 10 5 3 1 COLLECT There is a preset application installed at the terminal When the item is activated the preset application figure 5 3 1 would appear at the display Practice the example or press ESC key to return to MAIN MENU Figure 5 3 1 5 3 2 Upload Data The Upload function can upload data which keep at the SRAM to PC Please place the terminal onto cradle and connect to your PC before uploading the data Execute the selected item or press ESC key to return to MAIN MENU The example is that executing the Upload Data item 1 Upload Data Figure 5 3 2 Figure 5 3 2 1 Note This indicates the terminal is communicating with PC for data uploading 11 5 3 3 BROWSE This function of the item is that allowing user to browse all the data which keep in the SRAM 1 Data File Figure 5 3 3 Execute the selected item or press ESC key to return to MAIN MENU The example is that executing the Data File item Figure 5 3 3 1 Figure 5 3 3 1 shows the content of the data file You can select the data file by using arrow keys Up or Down to browse the next data or the previous data To edit or delete the presenting data press FN 1 to Edit and FN 2 to delete the data file selected Note The edit and delete function are only a
13. red When Low Battery Warning appears terminate the work and put the terminal to the cradle and recharge immediately 3 1 4 Auxiliary Battery The terminal is equipped with an auxiliary rechargeable battery to furnish the power supply to SRAM The auxiliary battery can work at least one month since the main battery removed from the terminal or the main battery stores no power Note The maintenance or replacement of Auxiliary Battery is for qualified service personnel only Any unauthorized changes or modifications could void the warranty 3 1 5 Replace Battery In case you need to replace the battery on your own follow the steps below Step 1 Press and push to unlock the battery cover Step 2 Remove the battery cover Sep 3 Slight lift and remove the battery from the battery compartment Step 4 Replace a new battery into the battery compartment and then replace the battery cover Note Make sure to turn off the terminal and upload the data in the terminal before battery replacement x Make sure the exposed cooper contacts of battery are engaged into the battery compartment Battery Disposal Do Not dispose the battery and make sure to follow the battery recycling guidelines 4 Communication Utility 4 1 Installing Cradle with USB interface cable Installing USB Driver When you plug in the USB interface cable to your host PC for the first time you will be prompted to install a device driver for the newly
14. t To install USB driver of BCP 8000 please refer to 4 Communication Utility for further information 3 1 2 Connecting to PC by the cradle with RS 232 interface cable REDLED BATTERY SYMBOL DB9F Connector to RS 232 Turn off computer before connection Connect the DC plug of the power adapter to the power jack which located at the DB9F connector Connect the DB9F connector with power jack connected to PC Connect the AC Adaptor to an electrical outlet The ORANGE power LED in front of the cradle would be lighted The cradle is ready for recharging the battery or terminal coniiguration Place the terminal onto the cradle You may hear a beep sound when the terminal is placed onto the cradle if the SETTING item Key Click is set to Enable There is a LED indicator on the top of the terminal and lit RED In the Display of the terminal there is a battery status icon indicates the battery status As the battery is being charged the battery status icon is varying and indicates the battery is charging lt takes approximately 6 hours to charge from low battery status When the battery is charged completely the battery status icon will turn to static and the terminal RED LED turns off 3 1 3 Low Battery Warning When the battery available capacity drops low a flashing empty battery icon will be appeared at the right bottom corner of the display There are about 500 scans can be made after the warning occur
15. ure 5 3 5 3 Figure 5 3 5 3 shows the test barcode information including barcode data type of barcode and the length of the barcode 5 3 5 4 Test The item provides self test function of Buzzer LCD LED and keypad 1 Buzzer Figure 5 3 5 4 16 Figure 5 3 5 4 1 Figure 5 3 5 4 1 shows that executing the keypad test and key in lower case of apple characters Note To alter states between upper case lower case character and number press ALPHA key to switch the type of characters or numbers 5 3 5 5 Baud Rate The item provides the setting of baud rate with variables from 1152000 bps down to 9600 bps 1 115200 bps Figure 5 3 5 5 5 3 5 6 Version This ttem provides showing Kernel Version of this terminal Figure 5 3 5 6 17 5 3 6 Download This download function provides selections of downloading the applications lookup file setting to the terminal 1 Program Figure 5 3 6 1 Program This item provides the function of downloading the application which developed under the Job Generator Utility 2 Setting This item provides the function of downloading the setting file which programmed under the Job Generator Utility 3 Update Kernel This item provides function of downloading the new Kernel file 4 Kernel Version This item provides function of downloading the Kernel Version file 5 Lookup File This item provides function of downloading the Lookup file s The maximu
16. vailable at data file while lookup file is not available with edit and delete function 12 5 3 4 DELETE The function allows user to delete the collected data Figure 5 3 4 1 All Data all the data would be deleted 2 Last Record last record would be deleted 3 Cancel all the data would be saved and return to Main Menu Figure 5 3 4 1 Select 1 Yes to delete the data and 2 No to quit Execute the selected item or press ESC key to return to MAIN MENU figure 5 3 4 1 5 3 5 Utilities The function of this item is that allowing user to set necessary parameters or some features that can help to enforce the terminal to meet application requirements 13 1 Memory Figure 5 3 5 5 3 5 1 MEMORY The item provides memory capacity checking and RAM Test 1 Memory Size Figure 5 3 5 1 Execute the selected item or press ESC key to return to MAIN MENU The example is that executing the RAM test Figure 5 3 5 1 1 Note The test is only carry out at the status of RAM empty Please upload and delete the collected data in the terminal before RAM Test figure 5 3 5 1 1 14 5 3 5 2 SETTING The function can configure the terminal parameters auto power off LCD backlight to optimize the convenient of the operation 1 Buzzer Pitch Figure 5 3 5 2 1 Buzzer Pitch The span between 000 255 Hz can be set 2 Record Prompt The span between 0000 9999 ms ca
17. xample is an applicable data collecting application which illustrates user with a circumstance of taking data in the filed checking inventory on site browse the collected data Please find the file of tysso apg under the EXAMPLE folder in the bundled CD disk The example includes Employee ID Location Item No Item Qty variables The data collecting job starts from key in employee no however it is one time work When the employee no is filled in the job sequence starts from key in data to Lcoation gt Item No gt Item gt Qty gt Location The example is also need a caption and selectable items to start or to end the job from beginning Under the Job Generator Utility the tysso apg is developed based on the variables and sequence which framed at the example The tysso apg includes FORM1 FORM2 and MENU1 respectively FORM1 Empl ID The way of key in the data is via barcode scan and keypad when finish the key in data to the field the terminal would jump into FORM2 FORM2 Location Item No Item Qty The way of key in the data is via barcode scan and keypad when finish the key in data to the fields the terminal would start again routine of Location gt ltem No gt ltem gt Qty gt till ESC key is pressed MENU1 Tysso Inventory is the caption of the example and the selection to start the example or to end the example by the selection of gt Check Stock and Exit Note
Download Pdf Manuals
Related Search