USB Card Reader Configuration Utility User Manual Draft !
Contents
1. Post Character that is send AFTER data See appendix A Output Length Number characters to be send Output Type Select Decimal Hexidecimal or ASCII Example Card data received 0x012F0123AE 37 bit b0000100101111000000010010001110101110 37 bit Required datas ASALAALARAL ALAA Required output 37335 Size 37 Offset 13 Length 18 Pre Post Output Length 5 Removes leading zero in 037335 Output Type Dec SB Research ApS Birkholmsvej 33 e DK 2800 Kgs Lyngby Tel 45 87 30 04 45 e Fax 45 87 30 04 46 Mifare Sector Parameters When using SBR 0904 MIS or SBR 0940 for reading data encode into a Mifare sector the access key and block number must be specified To format the data read from a Mifare sector format no 63 must be used Please see the Wiegand Programmable Format section above Mifare Block Memory location in card 0x00 Ox3F for S50 Mifare key type A key or B key Mifare key Specify key Hex 0x00000000000 OXFFFFFFFFFFFF Example ASCII encoded card number 7 digits in sector 04 first block Mifare A key 0x44BOFE872C8A Mifare Section Mifare Block 0x10 Mifare key type A key Mifare key 44BOFE872C8A Wiegand Section Size 128 Offset 72 Length 56 7 x 8 Bits ASCII code Pre Non Post Non Output Length 7 Output Type ASCII SB Research ApS Birkholmsvej 33 e DK 2800 Kgs Lyngby Tel 45 87 30 04 45 e Fax 45 87 30 04 46 Software Selected For2. DK 2800 Kgs Lyngby Tel 45 87 30 04 45 e Fax 45 87 30 04 46 Clock Data Programmable Format When using SBR 0814 SBR 0904 SBR 0950 with a card reading module that outputs data using Clock Data interface aka ABA2 or ISO 7918 Track 2 format no 31 can be selected using DIP or Software Select which allows for in field programming of format parameters listed below Size Number of characters to be received 1 37 Offset Characters that will be skipped 0 36 Length Characters that will be send 1 37 Pre Character that is send BEFORE data See appendix A Post Character that is send AFTER data See appendix A Output Type Select Decimal or Hexidecimal Example Card data received 00001230001234567890 Required output 0123456789 Enter Size 20 Offset 9 Length 10 Pre Non Post CR Output Type Dec SB Research ApS Birkholmsvej 33 e DK 2800 Kgs Lyngby Tel 45 87 30 04 45 e Fax 45 87 30 04 46 Wiegand Programmable Format When using SBR 0814 SBR 0904 SBR 0950 with a card reading module that outputs data using Wiegand interface format no 63 can be selected using DIP or Software Select which allows for in field programming of format parameters listed below Size Number of bits to be received 1 128 Offset Number of bits that will be skipped 0 127 Length Number of bits that will be send 1 128 Hex 1 40 Dec Pre Character that is send BEFORE data See appendix A
3. USB Card Reader Configuration Utility User Manual SB Research 2009 SB Research ApS e Birkholmsvej 33 e DK 2800 Kgs Lyngby es Tel 45 87 30 0445 e Fax 45 87 30 04 46 The Configuration Utility for USB card reader family Concept Hardware Software To allow for field programming of the USB card readers a configuration mode has been introduced with firmware 2 25 When the USB device is started in boot loader mode the device will allow update of the firmware and read write the E prom of the USB card reader The E prom holds the configuration data for Field Programmable Formats and the data to enable reading of Mifare sector data USB card reader hardware SBR 0814 with firmware 2 31 or later SBR 0904 with firmware 2 31 or later SBR 0940 with firmware 1 xx or later SBR 0951 with firmware 2 31 or later The Configuration Utility requires Microsoft net framework version 3 5 to be installed prior to launching the program The net framework can be downloaded from www microsoft com net Boot loader Mode To bring a USB reader into boot loader configuration mode one of the following procedures must be used depending on USB Reader hardware type SB Research ApS e Birkholmsvej 33 e DK 2800 Kgs Lyngby e Tel 45 87 30 04 45 Fax 45 87 30 04 46 SBR 0814 SBR 0904 Disconnect the USB cable Set DIP switch to 1 2 3 4 5 6 7 8 Off Off Off Off Off Off Off On Reconnect the USB cable The LED
4. mat When using SBR 0814 SBR 0904 the format selection CAN be done in software but when using SBR 0940 SBR 0950 the format selection MUST be done in software as there is no DIP switch Please note that activating Software Selected Format will override DIP settings Format Number Off 0 63 Revision history Date Notes 2009 08 12 Formatting changed amp Microsoft link changed 2009 07 30 First draft SB Research ApS Birkholmsvej 33 e DK 2800 Kgs Lyngby Tel 45 87 30 04 45 e Fax 45 87 30 04 46 Pre and Post characters available for selection ID Character ASCII ID Character ASCII 0 Space 0x20 32 0x40 1 0x21 33 A 0x41 2 0x22 34 B 0x42 3 0x23 35 C 0x43 4 0x24 36 D 0x44 5 0x25 37 E 0x45 6 amp 0x26 38 F 0x46 7 0x27 39 G 0x47 8 0x28 40 H 0x48 9 0x29 41 I 0x49 10 0x2A 42 J 0x4A 11 0x2B 43 K 0x4B 12 0x2C 44 L 0x4C 13 0x2D 45 M 0x4D 14 0x2E 46 N 0x4E 15 0x2F 47 O 0x4F 16 0 0x30 48 P 0x50 17 1 0x31 49 Q 0x51 18 2 0x32 50 R 0x52 19 3 0x33 51 S 0x53 20 4 0x34 52 T 0x54 21 5 0x35 53 U 0x55 22 6 0x36 54 V 0x56 23 7 0x37 55 W 0x57 24 8 0x38 56 X 0x58 25 9 0x39 57 Y 0x59 26 0x3A 58 Z 0x5A 27 3 0x3B 59 0x5B 28 lt 0x3C 60 0x5C 29 0x3D 61 0x5D 30 gt Ox3E 62 Tab 0x09 31 Ox3F 63 CR Enter 0x0D SB Research ApS Birkholmsvej 33 e DK 2800 Kgs Lyngby Tel 45 87 30 04 45 e Fax 45 87 30 04 46
5. will turn red and then yellow The USB reader is now in boot loader configuration mode and will be automatically detected by the Configuration Utility To return to normal mode of operation Disconnect the USB cable Set DIP switch to the desired format Reconnect the USB cable SBR 0940 SBR 0950 Disconnect the USB cable Press and HOLD the mode switch Reconnect the USB cable The LED will turn red and then yellow Release the mode switch The USB reader is now in boot loader configuration mode and will be automatically detected by the Configuration Utility To return to normal mode of operation Disconnect the USB cable Reconnect the USB cable SB Research ApS Birkholmsvej 33 e DK 2800 Kgs Lyngby Tel 45 87 30 04 45 e Fax 45 87 30 04 46 Configuration There is up to 4 parameter blocks in the USB Reader that can be configured Clock Data Programmable Format Wiegand Programmable Format Mifare Sector Parameters Software Selected Format Please see below table for applicable parameters per device Device Clock Data_ Wiegand Mifare Parameters Software Select SBR 0814 Yes Yes No Option SBR 0904 Yes Yes Option Option SBR 0940 No Yes Yes Yes SBR 0950 Yes Yes No Yes Activating Software Selected Format will override DIP settings Only valid for SBR 0904 MIS Mifare sector reader onboard SB Research ApS Birkholmsvej 33 e
Download Pdf Manuals
Related Search