User manual 250w moving head wash
Contents
1. CYAN CHANNEL 11 MAGENTA CHANNEL 12 YELLOW CHANNEL 13 C M Y speed CHANNEL 14 VECTOR MODES EXPLANATION CHANNEL 1 SHUTTER STROBE OPEN CLOSE DMX 512 VALUE 0 255 FUNCTION 11 160 STROBE SHUTTER ON OFF FAST SLOW 161 165 OPEN 166 195 OPEN SHUTTER EFFECT 196 225 CLOSE SHUTTER EFFECT 226 235 OPEN 236 245 RESET 246 250 CLOSE 251 255 OPEN CHANNEL 2 DIMMER DMX 512 VALUE 0 255 FUNCTION 0 255 0 100 CHANNEL 3 COLOR WHEEL 220 240 COUNTER CLOCKWISE ROTATION 241 255 BY RANDOM CHANNEL 4 FOCUS DMX 512 VALUE 0 255 FUNCTION 0 255 LINEAR FOCUSING CHANNEL 5 PANS 450 DEGREE DMX 512 VALUE 0 255 FUNCTION 0 255 PAN 450 DEGREE CHANNEL 6 TILTS 270 DEGREE DMX 512 VALUE 0 255 FUNCTION 0 255 TILT 270 DEGREE CHANNEL 7 PAN FINE ADJUSTMENT3 6 DEGREE DMX 512 VALUE 0 255 FUNCTION 0 255 PAN FINE ADJUSTMENT3 6 DEGREE CHANNEL 8 TILT FINE ADJUSTMENT3 6 DEGREE DMX 512 VALUE 0 255 FUNCTION 0 255 TILT FINE ADJUSTMENT3 6 DEGREE CHANNEL 9 PAN TILT SPEED ADJUSTMENT DMX 512 VALUE 0 255 FUNCTION 0 255 CHANNEL 10 CYAN DMX 512 VALUE 0 255 FUNCTION 0 255 CYANINE CHANNEL 11 MAGENTA DMX 512 VALUE 0 255 FUNCTION 0 255 MAGENTA CHANNEL 12 YELLOW DMX 512 VALUE 0 255 FUNCTION 0 255 YELLOW CHANNEL 13 C M Y SPEED DMX 512 VALUE 0 255 FUNCTION 0 127 FAST SL2. SAFETY ROPE AS SECONDARY ATTACHMENT VIA THE HOLES ON THE BASE OF THE DEVICE NEVER USE THE CARRYING HANDLES FOR SAFETY ROPES THE SAFETY ROPE USED MUST CAN HOLD AT LEAST 10 TIMES THE WEIGHT OF THE DEVICE ALWAYS INSPECT THE SAFETY ROPE TO SEE IF IT IS DAMAGED BEFORE USING IT INSPECT THE CONSTRUCTION STRUCTURE TO SEE IF IT CAN HOLD AT LEAST 10 TIMES THE WEIGHT OF ALL DEVICES CABLES ATTACHMENTS AND THE TRUSS SYSTEM 3 4 USE M 12 BOLTS GRADE 8 8 OR HIGHER TO LOCK THE CLAMPS TO THE TRUSS ALL BOLTS SHOULD BE STRONG AND TIGHTLY CONNECTED AND MUST NOT BE CORRODED OR RUSTED USE A SAFETY ROPE THAT CAN HOLD AT LEAST 10 TIMES THE WEIGHT OF THE DEVICE THE ENDS OF THE SAFETY ROPE IS DESIGNED SPECIALLY FOR THE CLAMPS CHECK THE PAN TILT LOCK TO SEE IF THEY ARE UNLOCKED CHECK IF THERE IS ANY INFLAMMABLE MATERIALS 1 METER AROUND MAINTENANCE BEFORE INSTALL OR REPLACE A LAMP THE AVERAGE LAMP LIFE OF A GE OSRAM PHILIP HMI 575W DISCHARGE LAMP IS APPROX 500 HOURS TO REPLACE A LAMP CHECK YOUR RECORD TO SFE IF THE LAMP LIFE IS EXCEEDED SWITCH THE DEVICE OFF AND UNPLUG THE POWER CABLE THE LAMP BECOMES VERY HOT DURING OPERATION IF THE LAMP THAT SHOULD BE REPLACED HAS JUST BEEN SWITCHED OFF WAIT UNTIL AT LEAST 15 MINUTES RELEASE THE 4 BIG SCREWS ON THE BACK OF THE MOVING HEAD REMOVE THE OLD LAMP AND REPLACE A NEW LAMP THE BUBBLE SHARP OF THE LAMP SHOULD BE ORIENTATED UPWARD INSERT THE LAMP FIRMLY TO THE LAMP SOCKET CLEAN TH
3. START A DEVICE IMMEDIATELY AFTER YOU SWITCHED IT OFF WAIT AT LEAST 15 MINUTES OTHERWISE YOU MIGHT DAMAGE THE DISCHARGE LAMP OR THE BALLAST ONLY HANDLE THE POWER CORD BY THE PLUG NEVER PULL OUT THE PLUG BY TUGGING THE POWER CORD WARNING REPLACE THE LAMP BY A QUALIFIED PERSON WHEN IT IS DAMAGED OR THE MAXIMUM BULB LIFE 750 HOURS HAS BEEN EXCEEDED WHEN THE DEVICE IS NOT IN USE OR YOU NEED TO REPLACE THE LAMP OR FUSE OR ANY PART SWITCH IT OFF THE DEVICE SHOULD BE ALWAYS EARTHED THE POWER SUPPLY YOU USE SHOULD BE COMPLIED TO THE LOCAL CONSTRUCTION AND ELECTRONIC REGULATIONS OVERLOAD PROTECTION AND PROPER EARTHING IS A MUST AVOID LOOKING DIRECT TO THE LIGHT SOURCE MEANT ESPECIALLY FOR EPILEPTICS AVOID EXPOSURE NAKED SKIN DIRECTLY UNDER THE LIGHTING BEAM WHEN REPLACE THE FUSE USE SAME TYPE AND RATING FUSE WITH PROPER STANDARD MARK AVOID SHORT CIRCUIT OF THE DEVICE FROM THE TEMPERATURE CONTROL SWITCH OR THE FUSE KEEP THE DEVICE AWAY FROM THE INFLAMMABLE MATERIALS SUCH AS CLOTH PAPER WOOD ETC KEEP THE FAN OF THE DEVICE AWAY FROM THE WALL OR OTHER OBJECTS THE DISTANCE SHOULD BE AT LEAST 0 1 METER WHEN THE SURFACE OF THE DEVICE BECOMES VERY HOT STOP THE DEVICE AND RE START IT AFTER AT LEAST 15 MINUTES REPLACE OR INSTALL THE DEVICE ALWAYS USE ORIGINAL PART FROM THE MANUFACTURER WHEN RIGGING DEREGGING THE DEVICE THE WORKING AREA SHOULD BE BLOCKED SO THAT NO OTHER PEOPL
4. indicator light will scintillate as the signal After setting ON be sure to break off the connecting with DMX controller and only one light can be set to main light it is not to change the DMX address setting of son light E g the address code son light can be set 001 or other number 5 rPAn pan reversion this function allow to reverse pan action Press Up or Down key to display rPAn if need reverse pls choose on If no press chooses OFF and press ENTER to Confirm save and exit 6 rtilt tilt reversion this function allow to reverse tilt action Press Up or Down key to display rtilt if need reverse pls choose on If no press chooses OFF and press ENTER to Confirm save and exit 7 choose operation mode Press Down or Up key to display dn pr press Enter again it will be display nod 1 or nod 2 After choosing press Enter is ok Operation mode nod 1 and nod 2 nod 1 Normal channels control nod 2 A few channels control DMX Audio O ESC DOWN UP ENTER CLAMP amp SAFETY ROPE THIS EQUIPMENT CAN BE PUT ON THE FLOOR OR INSTALLED TO ANY ORIENTATION WITH CLAMPS IT CAN BE LOCKED TO THE TRUSS QUICKLY AND EASILY WARNING 2 CLAMPS SHOULD BE USED TO INSTALL THE FIXTURE ALWAYS INSPECT THE CLAMPS TO SEE IF THEY ARE DAMAGED BEFORE USING THEM INSTALL THE DEVICE TO THE TRUSS WITH 2 CLAMPS WARNING ALWAYS USE AT LEAST ONE
5. AL LIGHT DESIGNERS FOR ITS STABLE AND DURABLE OPERATION NOW IT HAS BECOME ONE OF THE MOST SUCCESSFUL INTELLIGENT LIGHT FIXTURES YOU CAN FIND IN THE MARKET IT CAN SUPPLY BRIGHT COLOR WASHING EFFECT IT COMPLIES WITH CE STANDARDS SPECIFICATIONS COLOR 4COLORS OPEN COLOR TEMPERATURE RED GREEN ORANGE PURPLE OPEN SUTTER STROBE 0 10 F P S SPEED ADJUSTABLE PAN 450 DEGREE 8 16 BIT SELECTABLE ELECTRONIC RESETTING WITH DISPOSITION CORRECTION TITL 270 DEGREE 8 16 BIT SELECTABLE ELECTRONIC RESETTING WITH DISPOSITION CORRECTION CONTROL DMX 512 POWER SUPPLY 220V 50 60HZ OTHERS CAN ORDER LAMP MSD 250W DISCHARGE LAMP LAMP LIFE APPROX 500 HOURS FOR REFERENCE ONLY MOTOR 8 HIGH SPEED AND SUPER ACCURATE STEP MOTORS CONTROLLED BY HIGH SPEED CHIPS HOUSING FIRE RESISTANT FIRST CLASS ABS MATERIAL WITH HIGH TEMPERATURE PAINTING SUITABLE FOR CEILING WALL AND FLOOR INSTALLATION EASY INSTALLATION AND REMOVING BEAM PATH HIGH DENSITY QUARTZ LENS SET VENTILATION HIGH SPEED FAN COOLING PROTECTION AUTOMATIC OVER HEAT PROTECTION ANTI DISTURBANCE ELECTRIC CIRCUIT DIMENSION L400 x W450 x H570 mm WEIGHT 24kg DMX CHANNELS TOTAL 14 CHANNELS CHANNEL 1 STROBE OPEN CLOSE CHANNEL 2 DIMMER CHANNEL 3 COLOR 4 COLORS OPEN COLOR TEMPERATURE FILTER CHANNEL 4 FOCUS CHANNEL 5 PAN CHANNEL 6 TILTS CHANNEL 7 PAN FINE ADJUSTMENT 3 6 DEGREE CHANNEL 8 TILT FINE ADJUSTMENT 3 6 DEGREE CHANNEL 9 PAN TILT SPEED ADJUSTMENT CHANNEL 10
6. E BEAM PATH THE EXTERIOR AND INTERIOR LENS SHOULD BE CLEANED AFTER A PERIOD OF TIME TO INCREASE THE BRIGHTNESS ESPECIALLY UNDER A DUSTY CIRCUMSTANCE THE OBJECTIVE LENS SHOULD BE CLEANED EVERY TWO WEEKS FOR BEST EFFECT USE LENS CLEAN PASTE OR ALCOHOL ONLY THE COLOR FILTERS THE COLOR WHEEL THE REFLECTION CUP AND INTERNAL LENSES SHOULD BE CLEANNED AT LEAST EVERY 40 60 DAYS THE INTERIOR OF THE DEVICE NEED TO BE CLEANED AT LEAST ANNUALLY BY A VACUUM CLEANER OR AN AIR JET THE FANS REQUIRE A MONTHLY CLEANING FOR BETTER VENTILATION THE GOBOS THE GOBO WHEEL NEED TO BE CLEANED BY A SOFT BRUSH AT LEAST MONTHLY SAFETY INSTRUCTIONS FOR SAFETY REASONS PLEASE FOLLOW THE INSTRUCTIONS BELOW DO NOT OPEN THE DEVICE DO NOT MAKE ANY MODIFICATIONS DO NOT LET LIQUID WATER OR METAL TO COME INTO THE INTERIOR OF THE DEVICE DO NOT USE THE DEVICE WHEN THE HUMIDITY IS TOO HIGH WHEN SHOCK OR COLLISION OCCURS WHEN THE TEMPERATURE IS HIGHER THAN 40 C OR UNDER 0 C WARNING WHEN YOU MEET OPERATION PROBLEMS STOP IT IMMEDIATELY AND CONSULT THE DEALER THERE ARE NO SERVICEABLE PARTS INSIDE THE DEVICE EXCEPT FOR THE LAMP AND THE FUSE MAINTENANCE AND SERVICE OPERATION CAN BE ONLY CARRIED BY A AUTHORIZED DEALER TO OPEN MANY DEVICES OPEN THEM ONE BY ONE AFTER 5 MINUTES DO NOT OPEN THEM ONE TIME OTHERWISE THE VOLTAGE MIGHT BE DECREASED AND UNABLE TO IGNITE THE DISCHARGE LAMPS PROPERLY DO NOT RE
7. E CAN ENTER R NEVER PUT YOUR HAND ON THE DEVICE DURING ITS OPERATION THE OBJECTIVE LENS THE EXTERIOR AND INTERIOR OF THE DEVICE WILL BECOME DIRTY AFTER A PERIOD OF TIME ESPECIALLY UNDER DUSTY CIRCUMSTANCE YOU SHOULD CLEAN THE DEVICE ACCORDING TO THIS USER MANUAL SHOOTING CHART PROBLEM REASON POWER SUPPLY UD NO LIGHT OUTPUT NO AUTO RESETTING CORD NOT PLUGGED IN FUSE FAILURE POWER INDICATION LED DO NOT LIGHT SIGNAL CABLE OR DMX ADDRESS NOT LAMP ON AUTO RESET BUT YOU CAN PROPER CHECK SIGNAL CABLE OR DMX NOT CONTROL IT OR YOU CAN NOT START ADDRESS CONTROL A CHANNEL VOLTAGE IS TOO LOW OR THE LAMP LAMP NOT PROPER YOU CAN NOT LIFE WILL BE FINISHED SWITCH IT ON EVERYTIME CLEAN THE LENS OR THE LAMP LIFE THE LIGHT BEAM SPOT NOT BRIGHT WILL BE FINISHED LAMP ON AND OFF AFTER A PERIOD OF OVERHEAT PROTECTION WORKING THERE SHOULD NOT BE ANY DEFORMATION OR DAMAGE ON THE HOUSING LENS INSTALLATION PART MOVING PART AND POWER CABLES IF SUCH DEFORMATION OR DAMAGE OCCURS STOP THE DEVICE IMMEDIATELY AND CONSULT YOUR DEALER FOR REPLACEMENT TIME POWER SUPPLY NOT PROPER POWER CHECK FAN AND VENTILATION
8. OW 128 255 Automatism change color fast slow CHANNEL 14 VECTOR MODES DMX 512 VALUE 0 255 FUNCTION 0 255 COLOR VECTOR SIGNAL INPUT CONNECTION TO DMX 512 SIGNALS ONLY USE A FIRST CLASS 3 PIN STEREO SHIELDED CABLE AND 3 PIN XLR PLUGS AND CONNECTORS IN ORDER TO CONNECT THE CONTROLLER WITH THE FIXTURE OR ONE FIXTURE WITH ANOTHER AT THE LAST DEVICE THE DMX CABLE HAS TO BE TERMINATED WITH A TERMINATOR SOLDER A 120 OHIM RESISTOR BETWEEN DATA AND DATA INTO A 3 PIN XLR PLUG AND PLUG IT IN THE DMX OUTPUT OF THE LAST DEVICE DMX A Q O GND Digital display function amp address setting explain This control display menu is especially designed for all kinds of computer light fit out multifunctional control mode easy control For some model products have not the motion corresponding the menu option setting also null 1 REST FUNCTION Press Down or Up key after appear rSEt press Enter key it will rSEt when appear rSt 2 DMX512 Address setting This function can let you change this equipment address setting Press ESC key or time after time till appear A 001 then press Enter key letter A crush out At this time appear offside three digits After Using Up or Down to choose the address code which you want And then press Enter is ok 3 automatism amp sound control setting Press Down or Up appear Audi and then press E
9. User manual 250w moving head wash Professional Stage Lighting CONTENT STRUCTURE e asa sa aussi dese O EE oas deci 1 SPECIFICATION8S sess ti 1 DIVE CHANNELS N EE Spa ie die 1 STROBE OPAN TOSE ui ltd int 1 DIMMER iaa tidad ance 2 COLOR enel 2 FOCUS RA ia 2 PAN 450 DEGREE aia ais ae 2 TETZA DEGREE ii did 2 PAN FINE ADJUSTMENT 3 6 DEGREE 2 TILT FINE ADJUSTMENT 3 6 DEGREE 2 PAN TILT SPEED ADJUSTMENT asas ence TENEKE 2 EEEIEE IET E EPE AN 2 ied aa shuka qas ies ideas 3 MG i N 3 C M Y speed moriria sc VECTOR MODE anno ire 3 SIGNAL INPUT oy iii Ad A A AAA 3 CONNECT TO DMX512 SIGNAL 3 Digital display function amp address setting explain 4 CLAMP amp SAFETY ROPE on aa a yee idas 5 CLEAN MAINTENANCE rutas sre 5 INSTALL OR REPLACE ALAMP 6 CLEAN DHE BEAM PATEL 6 SAFETY INSTRUCTIONS 6 SHOOTING CHART A A A uae Coreen nies 7 THIS EQUIPMENT IS A POWERFUL MOVING HEAD WASHER LIGHT FIXTURE AFTER LONG TIME USING IN LARGE QUANTITY IN MANY DIFFERENT PLACES IT IS RECOMMENDED BY MANY PROFESSION
10. nter It will appear OFF or ON Press Down or Up again to choose OFF or On OFF automatism ON sound control After choose it pls press Enter key and them press Down or Up to choose test press Enter key again It will appear 1 and them press Enter again It will appear run At this time it would be running base on the setting above Setting OFF automatism ON sound control when running sound control green LED will be scintillating basis sound control frequency 4 Principal and subordinate synchronism control Main light setting press Down or Up key after appearing rSEt and then press Enter key to display nod 1 press Down or Up to display nast press Enter key again to appear OFF or ON Press Down or up key to choose OFF or ON Choose OFF this light is not the main light Choose ON this light is the main light After choosing it press Enter to fall back on nast Press Down or Up key again to display nod 1 Press Enter key display run Means running After setting the main light DMX S LED is light When receiving Principal and subordinate synchronism son light must be in the status of display address code if the equipment is not connect DMX controller the display will scintillate if the equipment is connect DMX controller the display won t scintillate But DMX signal
Download Pdf Manuals
Related Search