Biostar U8799 Owner's Manual
Contents
1. Item Options Description Date mm dd yy Set the system date Note that the Day automatically changes when you set the date Time hh mm ss Set the system internal clock IDE Primary Master Options are in its sub Press Enter to enter the menu sub menu of detailed options IDE Primary Slave Options are in its sub Press Enter to enter the menu sub menu of detailed options IDE Secondary Master Options are in its sub Press Enter to enter the menu sub menu of detailed options IDE Secondary Slave Options are in its sub Press Enter to enter the menu sub menu of detailed options 360K 5 25 in Select the type of floppy Drive 1 2M 525 in disk drive installed in your system 720K 3 5 in Drive B 1 44M 3 5 in 2 88M 3 5 in None Video EGA VGA Select the default video CGA 40 device CGA 80 MONO U8799 BIOS Setup Item Options Description Halt On All Errors Select the situation in which No Errors you want the BIOS to stop Base Memory All but Keyboard All but Diskette All but Disk Key N A the POST process and notify you Displays the amount of conventional memory detected during boot up Extended Memory N A Displays the amount of extended memory detected during boot up Total Memory N A Displays the total memory available in the system U8799 BIOS Setup 3 Advanced BIO2. CH 1497 3 e o gt SPEED muz ASP CLOCK o NIE cpu CLOCK MHz E OCK MEMORY UM 32 7 OVER ENTAGE 100 Hardware z Monitor Button na E Over clock percentage 100 ki Overclock Billion Voltage Button EO 1146 AM 3 Voltage Pane Click the Voltage button in Main Panel the button will be highlighted and the Voltage Panel wil slide ou to up as thefollowing figure In this panel you can decide to increase CPU core voltage and Memory voltage or noi The default setting is No If y ou want to get the best performance of overclocking we recommendy ou click the option Y es O A CEE 4 Overclock Panel Click the Ov ercloc button in Main Panel the button will be highlighted and the Overclock Panel wil slide ou to left as thef ollowing figure 21 Hee i rA E MS 7 imei NL E Button e oa n FI D m PA Por il Overclock Panel contains these features a 3MHz button 1MHz button 1MHz button and 3MHz button provide user the ability to doreal time overclock adjustment Warning Manually overclock is potentially dangerous especially when the overclocking percentage is over 110 We strongly recommend you verify every speed you overclock by click the Verify button Or you can just click Auto overclock button and let WarpSpeeder automaticallygets the best result for you b Recovery Dialog button Pop up the f
3. this option must set to NO The Choices No default Yes Reset Configuration Data The system BIOS supports the PnP feature which requires the system to record which resources are assigned and protects resources from conflict Every peripheral device has a node which is called ESCD This node records which resources are assigned to it The system needs to record and update ESCD to the memory locations These locations 4K are reserved in the system BIOS If the Disabled default option is chosen the system s ESCD will update only when the new configuration varies from the last one If the Enabled option is chosen the system is forced to update ESCDs and then is automatically set to the Disabled mode 25 U8799 BIOS Setup The above settings will be shown on the screen only if Manual is chosen for the resources controlled by function Legacy is the term which signifies that a resource is assigned to the ISA Bus and provides non PnP ISA add on cards PCI ISA PnP signifies that a resource is assigned to the PCI Bus or provides for ISA PnP add on cards and peripherals The Choices Disabled default Enabled Resources Controlled By By Choosing Auto ESCD default the system BIOS will detect the system resources and automatically assign the relative IRQ and DMA channel for each peripheral By Choosing Manual the user will need to assign IRQ amp DMA for add on cards Be sure that there are no
4. VIA 3058 AC97 Audio This option allows you to control the onboard AC97 audio The Choices Auto default Disabled Onboard Codec This option allows you to enable or disable the onboard Codec The Choices Enabled Default Disabled Onboard CMI Audio This item allows you to enable or disable the onboard CMI 8738 Audio Chip The Choices Enabled Default Disabled VIA 3068 MC97 Modem This option allows you to control the onboard MC97 modem The Choices Auto default Disabled VIA 3043 OnChip LAN This option allows you to control the onboard LAN The Choices Enabled Disabled default Onboard LAN Boot ROM This item allows you to enable or disable Onboard LAN Boot ROM The Choices Disabled default Enabled Super IO Device Press Enter to configure the Super I O Device Onboard FDC Controller Select Enabled if your system has a floppy disk controller FDC installed on the system board and you wish to use it If install and FDC or the system has no 17 U8799 BIOS Setup floppy drive select Disabled in this field The Choices Enabled default Disabled Onboard Serial Port 1 Select an address and corresponding interrupt for the first and second serial ports The Choices 3F8 IRQA default Disabled Auto 2F8 IRQ3 3E8 IRQ4 2E8 IRQ3 Onboard Serial Port 2 Select an address and corresponding interrupt for the first and second serial ports The Choices 2F8 IRQ3 default Disabled Auto 3F8
5. AGP Master 1 WS Read When Enabled read to the AGP Accelerated Graphics Port are executed with one wait states The Choices Disabled default Enabled DBI Output for AGP Trans The Choices Disabled default Enabled CPU amp PCI Bus Control If you highlight the literal Press Enter next to the CPU amp PCI Bus Control label and then press the enter key it will take you a submenu with the following options CPU to PCI Write Buffer When enabled up to four Dwords of data Can be written to the PCI bus without interrupting the CPU When disabled a write buffer is not used and the CPU read cycle will not be completed until the PCI bus signals that it is ready to receive the data The Choices Enabled default Disabled PCI Master 0 WS Write When Enabled writes to the PCI bus are executed with zero wait states The Choices Enabled default Disabled PCI Delay Transaction The chipset has an embedded 32 bit posted write buffer to support delay transactions cycles Select Enabled to support compliance with PCI specification The Choices Disabled Enabled default VLink 8X Support The Choices Disabled Default Enabled 14 U8799 BIOS Setup Memory Hole At 15M 16M You can reserve this area of system memory for ISA adapter ROM When this area is reserved it cannot be cached The user information of peripherals that need to use this area of system memory usually2 discussed their memory requireme
6. Graphics Port AGP An AGP card will take advantage of AGP technology for improved video efficiency and performance especially with 3D graphics Communication Network Riser Slot CNR1 The CNR specification is an open Industry Standard Architecture and it defines a hardware scalable riser card interf ace which supports modem only Front USB Header JUSB3 JUS B4 Pin Assignment Pin Assignment EC U 10 NA EN 5V Standby Front Panel Connector JPANEL1 PWR_LED y SAD DOOR JPANELI eei es SPK HLED RST ES Sleep Control Sleep Speaker 4 Ground Button mnm NA Connector Speaker POWER DD LED HardDrive LED DD LED Ground Reset Power on Reset Cortrol Button Button o Je Kv LI IDA 20 KEY IDA Connector PEN Connector I PIN Assigoment PIN Assignment pot ey n sy EXE TES S 13 Ground 4 ww a PSON 5 Ground 15 Ground 6 v t6 Ground T SATXPWR1 e wok is sv Standby Voltage 19 45V 5V 10 x 20 v RES Em cm n EISE Seu JATXPWR2 WS CL Power Source Selection for Keyboard and Mouse JKBV1 JKBV1 Assignment Description Description 1 e Glo 5V for key board and mouse Pin 1 2 Mu 1 e o 3 45V Standby PS 2 Mouse and PS 2 Key board are feo 2 3 close Voltage powered with 5V standby voltage Note In order to support this function Power on the system via keyboard and muse JKBV1 ju
7. IRQ DMA and I O port conflicts IRQ Resources This submenu will allow you to assign each system interrupt a type depending on the type of device using the interrupt When you press the Press Enter tag you will be directed to a submenu that will allow you to configure the system interrupts This is only configurable when Resources Controlled By is set to Manual IRQ 3 assigned to PCI Device IRQ 4 assigned to PCI Device IRQ 5 assigned to PCI Device IRQ 7 assigned to PCI Device IRQ 9 assigned to PCI Device IRQ 10 assigned to PCI Device IRQ 11 assigned to PCI Device IRQ 12 assigned to PCI Device IRQ 14 assigned to PCI Device IRQ 15 assigned to PCI Device PCI VGA Palette Snoop Choose Disabled or Enabled Some graphic controllers which are not VGA compatible take the output from a VGA controller and map it to their display as a way to provide boot information and VGA compatibility However the color information coming from the VGA controller is drawn from the palette table inside the VGA controller to generate the proper colors and the graphic controller needs to know what is in the palette of the VGA controller To do this the non VGA graphic controller watches for the Write access to the VGA palette and registers the snoop data In PCI based systems where the VGA controller is on the PCI bus and a non VGA graphic controller is on an ISA bus the Write Access to the palette will not show up on the ISA bus if the PCI VGA c
8. IRQ4 3E8 IRQ4 2E8 IRQ3 UART Mode Select This item allows you to determine which Infrared IR function of onboard I O chip The Choices Normal default ASKIR IrDA SCR UR2 Duplex Mode Select the value required by the IR device connected to the IR port Full duplex mode permits simultaneous two direction transmission Half duplex mode permits transmission in one direction only at a time The Choices Half default Full Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I O Address The Choices 378 IRQ7 default 278 IRQ5 3BC IRQ7 Disabled Parallel Port Mode The default value is SPP The Choices SPP Default Using Parallel Port as Standard Printer Port EPP Using Parallel Port as Enhanced Parallel Port ECP Using Parallel Port as Extended Capabilities P ort ECP EPP Using Parallel Port as ECP amp EPP mode ECP Mode Use DMA Select a DMA Channel for the port The Choices 3 default 1 Game Port Address Game Port I O Address The Choices 201 default 209 Disabled Midi Port Address Midi Port Base I O Address 18 U8799 BIOS Setup The Choices 330 default 300 Disabled Midi Port IRQ This determines the IRQ in which the Midi Port can use The Choices 10 default 5 Init Display First With systems that have multiple video cards this option determines whether the primary display uses a PCI Slot or an AGP Slot
9. The Choices PCI Slot default AGP OnChip USB Controller This option should be enabled if your system has a USB installed on the system board You will need to disable this feature if you add a higher performance controller The Choices All Enabled default All Disabled USB Keyboard Support Enables support for USB attached keyboards The Choices Disabled default Enabled IDE HDD Block Mode Block mode is otherwise known as block transfer multiple commands or multiple sector read write Select the Enabled option if your IDE hard drive supports block mode most new drives do The system will automatically determine the optimal number of blocks to read and write per sector The Choices Enabled default Disabled 19 U8799 BIOS Setup 6 Power Management Setup The Power Management Setup Menu allows you to configure your system to utilize energy conservation and power up power down features Figure 6 Power Management Setup ACPI function ACPI Suspend Type Power Management Option HDD Power Doun Suspend Mode Video Off Option Video Off Method MODEM Use IRQ Soft 0ff by PHRBTN Run VGABIOS if S3 Resume PHRON After PWR Fail Enabled S1 P0S User Define Disable Disable Suspend gt Off A SYNC Blank Instant 0ff Auto Off IRQ Event Activity Detect Press Enter ACPI Function This item displays the status of the Advanced Configuration and Power Management A
10. Using even pressure on both ends of the power indicator Ights are lit hard drive is DIMM press down firmly until the moduld spinning snaps into place PROBABLE SOLUTION System does not boot from hard disk drive can Check cable tunning from disk to diskcontrolle be booted from CD ROM drive board Make sure both ends are securel plugged in check the drive type in thd standard CMOS setup Backing up the hard drive is extremel important Al hard d amp ks are capable o PROBABLE SOLUTION System only boots from CD ROM Hard disk can Back up data and applications fles Reforma be read and applications can be used but the hard drive Re install applicatonsand dat booting from hard disk is impossible using backup disks PROBABLE SOLUTION Screen message says Invalid Configuration on Review system s equipment Make sure CMOS Failure correct informationis in setup PROBABLE Cannot boot system after installing secord hard Set master slave jumperscorrectly qu Run SETUP program and select correct drive manufactuers fo 26 03 03 2003 27 U8799 BIOS Setup BIOS SEP st E Main Menus zie es EEGEN 3 Standard CMOS Features ste een einer me it te ger 6 3 Advanced BIOS Features ici o cnrs eere e e ba enter re 9 4 Advanced Chipset Features 12 5 Integrated Peripherals rta tnu rere ENNER 16 6 Power Management Setup sus 20 T PnP PCI Configurations ende t dee ans 25
11. amp COMM activity Primary INTR On IRQ3 COM2 Disabled 23 U8799 BIOS Setup IRQ4 COMI Enabled IRQS LPT2 Enabled IRQ6 Floppy Disk Enabled IRQ7 LPTI Enabled IRQ8 RTC Alarm Disabled IRQ9 IRQ2 Redir Disabled IRQ10 Reserved Disabled IRQ11 Reserved Disabled IRQ12 PS 2 Mouse Enabled IRQ13 Coprocessor Enabled IRQ14 Hard Disk Enabled IRQ15 Reserved Disabled 24 U8799 BIOS Setup 7 PnP PCI Configurations This section describes configuring the PCI bus system PCI or Personal Computer Interconnect is a system which allows I O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with ts own special components This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings W Figure 7 PnP PCI Configurations PNP 0S Installed No Reset Configuration Data Disabled Resources Controlled By Auto ESCD ae 5 1f vou are i and Play PCI VGA Palette Snoop Disabled ing Assign IRQ For VGA Enabled gt t No if Assign IRQ For USB Enabled i Dess 0 ed De PNP OS Installed When set to YES BIOS will only initialize the PnP cards used for the boot sequence VGA IDE SCSI The rest of the cards will be initialized by the PnP operating system like Window 95 When set to NO BIOS will initialize all the PnP cards For non PnP operating systems DOS Netware
12. bit or True color 24 32 bit that is required for Direct3D rencering 23 5 Hardware Monitor Panel Click the Hardware Monitor button in Main Panel the button will be highlighted and the Hardware Monitor panel will slide ou to left as thef ollowing figure In this panel you can get the realtime status information of y our system The information will be rd reshed ever 1 second vaat SOS y CONTRE E m 6 Abou Panel Click the About button in Main Panel the buton will be highlighted and the About Panel will slide out to up as the following figure In this panel youcan get model name and detail inf ormation in hints of all the chipset that are related to overclocking You can also get the mainboard s BIOS model and the Version number d WarpSpeederTM utility 24 P ou EI Wersion 0959 TE 121 51 ele BA Sat MEH Note Because the overclock overvdtage and hardware monitor features are controlled by several separate chipset Warp Speeder divide these features to separate panels F one chipset is not on board the correlative button in Main panel will be disabled but will not interfere other panels functions This property can make WarpSpeeder utility more robus 25 Trouble Shooting No power to the system at al Power light don t Make sure power cable issecurely pugged in Contact techrica support PROBABLE SOLUTION System inoperative Keyboard lights are oni
13. has been powered down The Choices Off default On LPT amp COM When this option is set to On any event occurring at a COM serial LPT printer port will awaken a system which has been powered down The Choices LPT COM default COM LPT NONE HDD amp FDD When this option is set to On any event occurring on a hard drive or a floppy drive will awaken a system which has been powered down The Choices On default Off PCI Master When set to On you need a LAN add on card which supports the power function It should also support the wake up on LAN jump The Choices Off default On PowerOn by PCI Card When you select Enabled a PME signal from PCI card returns the system to Full ON state The Choices Disabled default Enabled Modem Ring Resume The Choices Disabled Default Enabled RTC Alarm Resume When Enabled you can set the date and time at which the RTC real time clock alarm awakens the system from Suspend mode The Choices Enabled Disabled default Date of Month You can choose which month the system will boot up This field is only configurable when RTC Resume is set to Enabled Resume Time hh mm ss You can choose the hour minute and second the system will boot up This field is only configurable when RTC Resume is set to Enabled IRQs Activity Monitoring Press Enter to access another sub menu used to configure the different wake up events i e wake on LPT
14. unfortunately the system s frequency that you are selected is not functioning there are two methods of booting up the system Method 1 Clear the CMOS data by setting the JCMOS1 2 3 closed as ON status All the CMOS data will be loaded as defaults setting Method 2 Press the Insert key and Power button simultaneously after that keep on pressing the Insert key until the power on screen showed This action will boot up the system according to FSB of the processor 31
15. 3 U8799 Fealtut6s 15 roam ass esse ds aaa TE do gra era essences 3 Package ContentS oocococcnconcomoncnnoncnnannnencanonennencn none nnm nnne nennen nennen nen 4 How to setup Jumper ms eene nnne nnne nenne nenne nennen 5 CPU Install tion Sege SSES ee Eeer exes 5 DDR DIMM Modules DIMM1 DIMM2 esses 6 Jumpers Headers Connectors amp Slots u 7 FRAN CAS e 14 Caract ristique de U8799 lessen nennen nennen nennen 14 WARPSPEEDER radial Ee in alas apa elas Ibbeertlipmee E System Requirement Installation Usage inciter oem vic kara diebus casn Ee Someta oe ad aliado qa dead es ua pasta care aC Ue cons TROUBLE SHOOTING aussi ccaeinms css reso teer ina do Eas aa cancion ho nep Pob ani as 26 Layout of U8799 for Version 3 1 amp below JPRNT B CONN PAXAIKI SECONDARY LZ rr SCT SLOT m ser EE ll NOTE represents thefirst pin Layout of U8799 Version 3 2 KRM JPRNTI JCOM 2 PRIMARY IDECONN V T R2 d ER ISI tee DD E DO ASP SPD IF_N 1 option al FC Il Tm USB4 PCISLOT IC E o ncs gt DES EEE NOTE represents thefist pin English U8799 Features A Hardware PU Provides Socket 478 E Supports Intel Pentium 4 processorup to 3 06 GHz E Supports Hy per Threading Technology E Front Side Bus a
16. CPI The Choices Enabled default Disabled ACPI Suspend Type The item allows you to select the suspend type under the ACPI operating system The Choices S1 POS default Power on Suspend S3 STR Suspend to RAM S1 amp S3 POS STR Power Management This category allows you to select the type or degree of power saving and is directly related to the following modes 1 HDD Power Down 2 Doze Mode 3 Suspend Mode 20 U8799 BIOS Setup There are four options of Power Management three of which have fixed mode settings Min Saving Minimum power management Doze Mode 1 hr Standby Mode 1 hr Suspend Mode 1 hr HDD Power Down 15 min Max Saving Maximum power management only available for sl CPU s Doze Mode 1 min Standby Mode 1 min Suspend Mode 1 min HDD Power Down 1 min User Defined default Allows you to set each mode individually When not disabled each of the ranges are from 1 mm to 1 hr except for HDD Power Down which ranges from 1 min to 15 min and disable HDD Power Down When enabled and after the set time of system inactivity the hard disk drive will be powered down while all other devices remain active The Choices Disabled default 1Min 2Min 3Min 4Min 5Min 6Min 7Min 8Min 9Min 10Min 11Min 12Min 13Min 14Min 15Min Suspend Mode When enabled and after the set time of system inactivity all devices except the CPU will be shut off The Choic
17. S Features W Figure 3 Advanced BIOS Setup Virus Marning Disabled CPU L1 amp L2 Cache Enabled CPU L2 Cache ECC Checking Enabled Menu Level gt Quick Power On Self Test Enabled First Boot Device Show summary screen Second Boot Device Third Boot Device Boot Other Device Enabled Swap Floppy Drive Disabled Boot Up Floppy Seek Enabled Boot Up NumLock Status On Typematic Rate Setting Disabled Security Option Setup OS Select For DRAM gt 64MB Non 0S2 Video BIOS Shadow Enabled Summary Screen Show Disabled Virus Warning This option allows you to choose the VIRUS Warning feature that is used to protect the IDE Hard Disk boot sector If this function is enabled and an attempt is made to write to the boot sector BIOS will display a warning message on the screen and sound an alarm beep Disabled default Virus protection is disabled Enabled Virus protection is activated CPU L1 amp L2 Cache Depending on the CPU chipset in use you may be able to increase memory access time with this option Enabled default Enable cache Disabled Disable cache CPU I2 Cache ECC Checking This item allows you to enable disable CPU L2 Cache ECC Checking The Choices Enabled default Disabled Quick Power On Self Test Enabling this option will cause an abridged version of the Power On Self Test POST to execute after you power up the computer U8799 BIOS Setup Disabled Normal POST Enabled default Enab
18. SPC Health Status eee ec to eee teta e ER Re e 28 9 Frequency Control sies iac ng certe dr e e ine 30 U8799 BIOS Setup BIOS Setup Introduction This manual discussed Award M Setup program built into the ROM BIOS The Setup program allows users to modify the basic system configuration This special information is then stored in battery backed RAM so that it retains the Setup information when the power is turned off The Award BIOS installed in your computer system s ROM Read Only Memory is a custom version of an industry standard BIOS This means that it supports Intel Pentium 4 processor input output system The BIOS provides critical low level support for standard devices such as disk drives and serial and parallel ports Adding important has customized the Award BIOSTM but nonstandard features such as virus and password protection as well as special support for detailed fne tuning of the chipset controlling the entire system The rest of this manual is intended to guide you through the process of configuring your system using Setup Plug and Play Support These AWARD BIOS supports the Plug and Play Version 1 0A specification ESCD Extended System Configuration Data write is supported EPA Green PC Support This AWARD BIOS supports Version 1 03 of the EPA Green PC specification APM Support These AWARD BIOS supports Version 1 1 amp 1 2 of the Advanced Power Management APM specification Power management feat
19. U8799 FCC Information and Copyright This equipment has beentested and found to comply with the limits ofa Class B digital device pursuant to Part 15 ofthe FCC Rules T hese limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications There is no guarantee that interference will not occur in a particular installation The vendor makes no representations or warranties with respect to the contents here of and specially disclaims any implied warranties of merchantability or fitness for any purpose Further the vendor reserves the right to revise this publication and to make changes to the contents here of without obligation to notify any party beforehand Duplication of this publication in part or in whole is not allowed without fist obtaining the vendors approval in writing The content ofthis user s manualis subject to be changed without notice and we will not be responsible for any mistakes found in this user s manual All the brand and product names are trademarks of their respective companies Content LAYOUT OF U8799 FOR VERSION 3 1 amp BELOW 1 LAYOUT OF U8799 VERS ION 3 2 ee eeee ee ee eee ee ee eee eene sesta ae ses etna aee 2 X820 SD E eec O
20. d 3 Mic Power Bass re Audio Power 5 Right Line Out Right Right Line Out Right Speaker Out Speaker Out 7 Reseved 8 Key 9 Left Line Out Left Left Line Out Left Speaker Out Speaker Out 1 Right Line Ir Right Rear Right Line Ir Right Rear Speaker Speaker 13 Left Line Inv Left Rear Left Line Iv Left Rear Speaker Speaker Front Panel Audio Header JAUDIO 1 optional IEOL OOCOO 5 JAUDIO1 ch Pin Pin Assignment 1 McinCener 2 Ground 3 4 Audio Power 5 ER Right Line Out Right Speaker Out Speaker Out 7 8 Key 9 pus Left Line Out Left Speaker Out Speaker Out 11 12 Surender Lett 13 Ges 14 Subwoof 15 16 Ke Digital Audio Canector JS PDIF OUTI JSPDIF INT optional 1 3 5V JSPDIF OUT1 2 SPDIF_OUT s com 11 Game Port Header JGAME1 Wl Bees JGAME1 Pin Assignment Pin Assignment RE 5V Joy stick B Buton 1 og Joy stick AButton 1 Joy stick B Coordinate x e Laag A Coordinate X MDI Output Ground Joy stick B Coordinate Y Joy stick B Buton 2 Joy stick A Coordinate Y i3 MDiimpe 14 Joystick AButton 2 pois NA tg owy AUDIO DJ Connector JDJ1 PIN Assignment PIN Assignment Defesa we EE easels ee fem 1 Ground JPRNTI JUSBLAN 1 Parallel o Line In Speaker Out MIC In PS 2 Keyboard JCOMI JCOM2 JAUDIO 12 6 Channel Speakers H eh Line In Rear Speaker Spe AP Mic In Center am
21. d features ofthe BIOS Advanced Chipset Features This submenu allows you to configure special chipset features U8799 BIOS Setup Integrated Peripherals This submenu allows you to configure certain IDE hard drive options and Programmed Input Output features Power Management Setup This submenu allows you to configure the power management features PnP PCI Configurations This submenu allows you to configure certain Plug and Play and PCI options PC Health Status This submenu allows you to monitor the hardware of your system Frequency Control This submenu allows you to change CPU Vcore Voltage and CPU PCI clock However this function is strongly recommended not to use Not properly change the voltage and clock may cause CPU or M B damage Load Optimized Defaults This selection allows you to reload the BIOS when the system is having problems particularly with the boot sequence These configurations are factory settings optimized for this system A confirmation message will be displayed before defaults are set Load Optimized Defaults V N N Set Supervisor Password Setting the supervisor password will prohibit everyone except the supervisor from making changes using the CMOS Setup Utility You will be prompted with to enter a password Enter Password Set User Password If the Supervisor Password is not set then the User Password will function in the same way as the Supervi
22. dows 98 SE Windows 2000 Windows Me Windows XP SCOUNIX etc Package contents E HDD Cable X 1 FDD Cable X 1 User s Manual X 1 USB Cable X 1 optional Rear I O Panelf or Mcro ATXCase X1 optional Fuly SetupDriv er CD X1 Howto setup Jumper The illustration shows how jumpers are setup When the Jumper cap is placed onpins the jumper is close If no jumper cap is placed on the pins the jumper is open The illustration shows a 3 pin jumper whose pin 1and 2 are close when jumper cap is placed on these2 pins TW Jumper close Jumper open Pin 1 2 close CPU Installation Step1 Pull the lever sideway s away from the socket and then raise the lever up to a 90 degree angle Step2 Look for the white dot cut edge The white dot cut edge should point towards the lev er piv ot The CPU will fit only in thecorrect orientation Step3 Hold the CPU downfimly and then close the lever Step4 Put the CPU fan onthe CPU and buckle it Connect the CPU fan power cable to the JCFAN1 This completes the installation CPU Fan Header JCFAN1 3 1 Ground l 2 12V SEPAN FAN rpm Rate Sense System Fan Header JSFAN1 DDR DIMM Modules DIMMI DIMM2 DRAM Access Time 2 5V Unbuffered DDR 200 266 333 400 MHz Type required DRAM Type 64MB 128MB 256VB 512MB 1GB DIMM Module 184 pin Total Memory Size with Un buffered DIMMs Location Size MB Maxis 2 GB DIMMB2 64MB 128MB 256MB 5 12MB 1GB 41 On
23. eactivate an interface if you are going to installa primary and or secondary add in IDE interface The Choices Enabled default Disabled IDE Prefetch Mode The onboard IDE drive interfaces supports IDE prefetching for faster drive access If the interface does not support prefetching If you install a primary and or secondary add in IDE interface set this option to Disabled The Choices Enabled default Disabled Primary Secondary Master Slave PIO The IDE PIO Programmed Input Output fields let you set a PIO mode 0 4 for each of the IDE devices that the onboard IDE interface 16 U8799 BIOS Setup supports Modes 0 to 4 will increased performance progressively In Auto mode the system automatically determines the best mode for each device The Choices Auto default Mode0 Model Mode2 Mode3 Mode4 Primary Secondary Master Slave UDMA Ultra DM A 100 functionality can be implemented if it is supported by the IDE hard drives in your system As well your operating environment requires a DMA driver Windows 95 OSR2 or a third party IDE bus master driver If your hard drive and your system software both support Ultra DMA 100 select Auto to enable BIOS support The Choices Auto default Disabled VIA OnChip PCI Device If you highlight the literal Press Enter next to the VIA OnChip PCI Device label and then press the enter key it will take you a submenu with the following options
24. emory Hole Disabled System BIOS Cacheable Disabled Video RAH Cacheable Disabled Delay Prior to Thermal 16 Hin NB Power Management Enabled a DRAM Clock Drive Control To control the Clock If you highlight the literal Press Enter next to the DRAM Clock label and then press the enter key 1t will take you to a submenu with the following options DRAM Clock This item determines DRAM clock following 100MHz 133MHz or By SPD The Choices 100MHz 133MHz By SPD default DRAM Timing This item determines DRAM clock timing follow SPD or not The Choices By SPD default Manual SDRAM CAS Latency When DRAM is installed the number of clock cycles of CAS latency depends on the DRAM timing The Choices 2 5 2 default 12 U8799 BIOS Setup Bank Interleave This item allows you to enable or disable the bank interleave feature The Choices Disabled default Precharge to Active Trp This items allows you to specify the delay from precharge command to activate command The Choices 2T 3T default Active to Precharge Tras This items allows you to specify the minimum bank active time The Choices 7T default 6T Active to CMD Trcd Use this item to specify the delay from the activation of a bank to the time that a read or write command is accepted The Choices 2T 3T default DRAM Command Rate This item controls clock cycle that must occur between the last valid write operati
25. es Disabled default 1Min 2Min 4Min 8Min 12Min 20Min 30Min 40Min 1Hour Video Off Option This field determines when to activate the video off feature for monitor power management The Choices Suspend Off default Always on Video Off Method This option determines the manner in which the monitor is goes blank V H SYNC Blank default This selection will cause the system to turn off the vertical and horizontal 21 U8799 BIOS Setup synchronization ports and write blanks to the video buffer Blank Screen This option only writes blanks to the video buffer DPMS Initial display power management signaling MODEM Use IRQ This determines the IRQ which can be applied n MODEM use The Choices 3 default 4 5 7 9 10 11 NA Soft Off by PWR BTTN Pressing the power button for more than 4 seconds forces the system to enter the Soft Off state when the system has hung The Choices Delay 4 Sec Instant Off default Run VGABIOS if S3 Resume Choosing Enabled will make BIOS run VGA BIOS to initialize the VGA card when system wakes up from S3 state The system time is shortened if you disable the function but system will need AGP driver to initialize the card So if the AGP driver of the VGA card does not support the initialization feature the display may work abnormally or not function after S3 The Choices Auto default Yes No PWRON After PW R Fail This field determine
26. le quick POST First Second Third Boot Other Device These BIOS attempts to load the operating system from the devices in the sequence selected in these items The Choices Floppy LS120 HDD 0 SCSI CDROM HDD 1 HDD 2 HDD 3 ZIP 100 LAN Enabled Disabled Swap Floppy Drive For systems with two floppy drives this option allows you to swap logical drive assignments The Choices Enabled Disabled default Boot Up Floppy Seek Enabling this option will test the floppy drives to determine if they have 40 or 80 tracks Disabling this option reduces the time it takes to boot up The Choices Enabled default Disabled Boot Up NumLock Status Selects the NumLock State after power on On default Numpad is number keys Off Numpad is arrow keys Typematic Rate Setting When a key is held down the keystroke will repeat at a rate determined by the keyboard controller When enabled the typematic rate and typematic delay can be configured The Choices Disabled default Enabled Typematic Rate Chars Sec Sets the rate at which a keystroke is repeated when you hold the key down The Choices 6 default 8 10 12 15 20 24 30 Typematic Delay Msec Sets the delay time after the key is held down before it begins to repeat the keystroke The Choices 250 default 500 750 1000 Security Option This option will enable only individuals with passwords to bring the system online and or to use the CMOS Setup Utilit
27. ly for reference InstallingDDR Module 1 Unlock a DIMM slot by pressing the retaining D d clips outward Align a DIMM onthe slot in E the wa that the notch onthe DIMM matches L the break ontheslot 2 Insertthe DIMMfirmly and vertically into the FT LU slot until the retaining chip snap back in TI e place and the Dimm is properly seated Jumpers Headers Connectors amp Slots Floppy Disk Connector FDD1 The motherboard provides a standard floppy disk connector tha supports 360K 720K 1 2M 1 44M and 2 88M floppy disk types This connedor supports the prov idedfloppy drive ribbon cables Hard Disk Connectors IDE1 IDE2 The motherboard has a 32 bit Enhanced PCI IDE Controller that provides PIO Mode 0 4 Bus Master and Ultra DMA 33 66 100 133 functionality It has two HDD connectors IDE1 primary and IDE2 secondary The IDE connectors can connect a master and a slave driv e soyou canconnect up to four hard disk drives The first hard drive should alway s be connected to IDE1 Peripheral Component Interconnect Slots PCI 1 3 This motherboard is equipped with 3 standard PCI slots PCI stands f or Peripheral Component Interconnect and it is a bus standard for expansion cards This PCI slot is designated as 32 bits Accelerated Graphics Port Slot AGPI Your monitor will attach directly to that video card This motherboard supports video cards for PCI slots but it is also equipped with an Accelerated
28. mper cap should be placed on pin 2 3 L t N 1 Case Open Connector JC1 le HEM Case Open Signal Power Source Selection for USB JUSB V1 JUS BV2 JUS BV3 JUSBV2 JUSBV3 Assignment Description JUSBV2 5V for USB located at the JUSBLAN 1 port Pin 1 2 close JUSBV3 5V for USB located at the JUSB3 4 ports 1 O O 5v Standby JUSBV2 JUSBLAN1 port ra wit eio c ei standby v otage of 5V Pin 2 3 close JUSBV3 SE ds orts pores with Note In orderto support this function Power on the system via USB device JUSBV2 JUSB V3 jumper cap should be placed on pin 2 3 respectively Clear CMOS Jumper JCMOS1 JCMOS Assignment Normal Operation default Pin 1 2 Close 8 19 Clear CMOS Data Pin 2 3 Close oe The following procedures are for resetting the BIOS password It is important to follow these WAKHYOUTZIT instructions closely X Clear CMOS Procedures 1 Remove AC power line 2 Setthe jumper to Pin 2 3 close 3 Wat for fiv e seconds 4 Setthe jumper to Pin 1 2 close 5 Power on AC 6 Reset y our desired password or clear the CMOS data CD ROM Audio In Header JCDIN1 JCDIN2 optional Pin Assignment 4 LeftChamelimut l 2 Ground JCDIN1 2 Rm Right Channel Input 10 Front Panel Audio Header JAUDIO1 2600 QGDOJ 4 1852000003 JAUDIOI Pin Assignment Pin Assignment 1 Moin Center 2 Groun
29. ne st r o E Gestion d alimentation avanc e et capacit s d conomie d nergie P riph riques int gr a t arri re E 2 ports s rie E 1 port parall le mode SPP EPP ECP 1 port audio en position verticale E 1 port LAN E 1 souris PS 2 E 1 clavier PS 2 E 4 ports USB2 0 b Gt frontal E 1 port disquette prenant en charge 2 FDD avec 360K 720K 1 2M 1 44Met 2 88 Mo E 4 ports USB2 0 1 connecteur front audio Dimensions E Facteur de Forme Micro ATX 24 5 X 22 5cm Larg XL B BIOS amp Software BIOS Award legal Bios APM1 2 ACPI Fonction USB Logiciel il EM i Supporte Warpspeecer 9th Touch FLASHER WinHasher Qfrant la meilleure perfomance pour Windows 98 SE Windows 2000 Windows Me Windows XP UNIX series etc 15 WarpSpeeder Introduction WarpSpeeder a new power ul control utility features three userfriendly functions including Ov erclok Manager Ov ervoltage Manager and Hardware Monitor With the Ov erclok Manager users can easily adjust the frequency they prefer orthey can get the best CPU perfomance with just one click The Ov ervoltage Manager on the other hand helps to power up CPU core voltage and Memory voltage The cool Hardware Monitor smartly indicates the temperatures voltage and CPU fan speed as well as the chipset irf ormation Also in the About panel you can get detail descriptions about BIOS model and chipsets In addition the frequency status
30. nts The Choices Disabled default Enabled System BIOS Cacheable Selecting the Enabled option allows caching of the system BIOS ROM at F0000h FFFFFh which can improve system performance However any programs writing to this area of memory will cause conflicts and result in system errors The Choices Enabled Disabled default Delay Prior to Thermal Set this item to enable the CPU Thermal function to engage after the specified time The Choices 16Min default 4Min 8Min 32Min NB Power Management This item allows you to enable or disable NB Power Management The Choices Disabled Enabled Default 15 U8799 BIOS Setup 5 Integrated Peripherals W Figure 5 Integrated Peripherals VIA OnChip IDE Device Press Enter VIA OnChip PCI Device Press Enter SuperIO Device Press Enter Menu Level ke Init Display First PCI Slot OnChip USB Controller All Enabled USB Keyboard Support Disabled IDE HDD Block Mode Enabled VIA OnChip IDE Device If you highlight the literal Press Enter next to the VIA OnChip IDE Device label and then press the enter key it will take you a submenu with the following options IDE DMA Transfer Access The Choices Enabled default Disabled OnChip IDE Channel 0 1 The motherboard chipset contains a PCI IDE interface with support for two IDE channels Select Enabled to activate the first and or second IDE interface Select Disabled to d
31. of CPU memoy AGP and PCI along with the CPU speed are synchronically shown on our main panel Moreov er to protect users computer systems if the setting is nd appropriate when testing and results in system fail or hang WarpSpeeder technology assures the system stability by automatically rebooting the computer and then restart to a speed that is either the original system speed or a suitable one System Requirement OS Support Windows 98 SE Windows Me Windows 2000 Windows XP DirectX DirectX 8 1 or above The Windows XP operating system includes DirectX 8 1 If you useWindows XP y oudo not need to insall DirectX 8 1 16 Installation 1 Execute the setup execution file and then the following dialog will pop up Please click Next button andf ollow the ddault procedure to install Welcome to the InstallShield Wizard for W arpSpeeder The InstallShieldR Wizard will install WarpSpeeder on your computer To continue click Next 2 When you see the following dialog in setup procedure it means setup is completed If the Launch the WamSpeeder Tray Utility checkbox is checked the Tray Icon utility and WarpSpeeder utility will be automatically and immediately launched after y ou click Finish button 17 InstallShield Wizard Complete Setup has finished installing W arpSpeeder on your computer dance Usage The folowing figures are just only for reference the screen prin
32. ollowing dialog Let user select a restoring way if system need to do afail safe reboot 22 Recovery Options Please select a recovery option that will decide what kind of restoring you want to do after system fail safe reboot Options Group Restore to Hardware Default CPU Clock Value Cc Auto ov erclock button User can click this button and WarpSpeeder M will set the best and stable performance andfrequency automatically WarpSpeeder utility will execute a series of testing until systemfail Then system will dofail safe reboot by using Watchdog function Ater reboot the WarpSpeeder utility will restore to the hardware ddaul setting or load the verified best and stable frequency accordingto the Recovery Dialogs setting d Verify button User can click this button and WarpSpeeder will proceed a testingf or current frequency If the testing is ok then the current f requeno will be sa ed into system registry If the testing fail system wil do a fail safe rebooting After rebod the WarpSpeeder utility will restore to the hardware default setting or load the verified best and stable frequency according to the Recovery Dialog s setting Note Because the testing programs invoked in Auto overdock and Verify include DirectDraw Direct3D and DirectShow ests the DirectX 8 1 or newer runtime library is required Ard please make sure your display card s color depth is High color 16
33. on and the next command The Choices 1T Command default 2T Command DRAM Burst Len The Choices 4 default 8 Write Recovery Time The Choices 3T default 2T AGP amp P2P Bridge Control If you highlight the literal Press Enter next to the AGP amp P2P Bridge Control label and then press the enter key it will take you a submenu with the following options AGP Aperture Size Select the size of the Accelerated Graphics Port AGP aperture The aperture is a portion of the PCI memory address range dedicated for graphics memory address space Host cycles that hit the aperture range are forwarded to the AGP without any translation The Choices 64M default 256M 128M 32M 16M 8M 4M AGP Mode This item allows you to select the AGP Mode The Choices 4X default 2X 1X AGP Driving Control By choosing Auto the system BIOS will the AGP output Buffer Drive strength P Ctrl by AGP Card By choosing Manual it allows user to set AGP output 13 U8799 BIOS Setup Buffer Drive strength P Ctrl by manual The Choices Auto default Manual AGP Driving Value While AGP driving control item set to Manual it allows user to set AGP driving The Choices DA default AGP Fast Write The Choices Enabled Disabled default AGP Master 1 WS Write When Enabled writes to the AGP Accelerated Graphics Port are executed with one wait states The Choices Disabled default Enabled
34. ontroller responds to the Write In this case the PCI VGA controller should not respond to the Write it should only snoop the data and permit the access to be forwarded to the ISA bus The non VGA ISA graphic 26 U8799 BIOS Setup controller can then snoop the data on the ISA bus Unless you have the above situation you should disable this option Disabled default Disables the function Enabled Enables the function Assign IRQ For VGA This item allows the users to choose which IRQ to assign for the VGA The Choices Enabled default Disabled Assign IRQ For USB This item allows the users to choose which IRQ to assign for the USB The Choices Enabled default Disabled 27 U8799 BIOS Setup 8 PC Health Status W Figure 8 PC Health Status Shutdoun Temperature Disabled Item Help Menu Level Show H W Monitor in POST Enabled Previo e 1 ed De Shutdown Temperature This item allows you to set the shutdown temperature of the CPU in order not to be damaged by the overheated temperature When this function is enabled the system will automatically shutdown if the CPU temperature reaches the shutdown temperature This function only works under Windows 98 ACPI mode The Choices Disabled default 60 C 140 F 65 C 149 F 70C 158 F 75C 167 F CPU Vcore 3 3V 5 0V 12V 12V 5V 5V SB Voltage Battery Detect the system s voltage status automatically Current CPU Temperat
35. p Bass NC Om 00 lm 13 Fran ais Caract ristique de U8799 A Mat riel rocesseur Socket 478 E Supporte processeur Intel Pentium 4 E Supporte latechnologie Hyper Threading E FSB 400 533 800 MHz Jeu des Puces E North Bridge VIA P4X400 E South Bridge VIA VT8235 M moire principale E Prise en charge de deux p riph riques 2 DDR E Prise en charge des p riph riques DDR 200 266 333 400 MHz E Taille maximale de la m moire 2Go Super E S E Puce ITE IT8705 E Interface de Comptage de Broche Faible E Offre laforctionnalit Super E S h rit e la plus couramment utilis e E Initiatives de Contr le d Environnement Moniteur H W Fonction Smart Guardian de ITE Slots E Trois slots de ma trise de bus PCI 32 bits E Un slot CNR E Un slot compatible AGP 4X 8X IDEint gr E Supporte quatre lecteurs de disque IDE E Supporte PIO Mode 0 4 et Ultra DMA 33 66 100 133 Bus Master Mode LAN E Puce VIA VT6103 I Supporte lefonctionnement en auto n gociation 10 Mb s et 100 Mb s E Capacit Half Full duplex wee Son C 97 int gr seuement pour version au dessousde 3 1 Puce CM9739A E Conf ome aux sp cifications AC 97 14 E Supporte 6 canaux Codec Son C 97 int gr seulement pour version au dessus de 3 2 E Puce CMI9761A Conf ome aux sp cifications Intel AC 97 Rev 2 3 E R pond aux exigerces de Microsoft PC2001 E Supporte 6canaux E Supporte le micropho
36. s the action the system will automatically take when power is restored to a system that had lost power previously without any subsequent manual intervention There are 3 sources that provide current to the CMOS area that retains these Power On instructions the motherboard battery 3V the Power Supply 5VSB and the Power Supply 3 3V While AC is not supplying power the motherboard uses the motherboard battery 3V If AC power is supplied and the Power Supply is not turned on 5VSB from the Power Supply is used When the Power Supply is eventually turned on 3 3V from the Power Supply will be used There are 3 options Former Sts On Off Off default Means always set CMOS to the Off status when AC power is lost On Means always set CMOS to the On status when AC power is lost Former Sts Means to maintain the last status of the CMOS when AC power is lost For example If set to Former Sts and AC power is lost when system is live then after AC power is restored the system will automatically power on If AC power is lost when system is not live system will remain powered off 22 U8799 BIOS Setup IRQ E vent Activity Detect If you highlight the literal Press Enter next to the IRQ Event Activity Detect label and then press the enter key it will take you a submenu with the following options VGA When set to On any event occurring at a VGA Port will awaken a system which
37. sor Password If the Supervisor Password is set and the User Password is set the User will only be able to view configurations but will not be able to change them Enter Password U8799 BIOS Setup Save amp Exit Setup Save all configuration changes to CMOS memory and exit setup Confirmation message will be displayed before proceeding SAVE to CMOS and EXIT Y N Y Exit Without Saving Abandon all changes made during the current session and exit setup Confirmation message will be displayed before proceeding Quit Without Saving V N N Upgrade BIOS This submenu allows you to upgrade bios BIOS UPDRTE UTILITV V N N U8799 BIOS Setup 2 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into 10 categories Each category includes no one or more than one setup items Use the arrow keys to highlight the item and then use the lt PgUp gt or lt P gDn gt keys to select the value you want in each item W Figure 2 Standard CMOS Setup Date mm dd yy Jun Ee Item Help Time hh mm ss ERON Menu Level gt IDE Primary Master IDE Primary Slave Change the day month IDE Secondary Master year and century IDE Secondary Slave Drive fl 1 44M 3 5 in Drive B None Video EGA VGA Halt On All But Keyboard U8799 BIOS Setup Main Menu Selections This table shows the selections that you can make on the Main Menu
38. t 400 533 MHz Chipset E North Bridge VIA P4X400 E South Bridge VIA VT8235 Main Memory E Supports up to 2 DDR devices E Supports 200 266 333 400 MHz DDR devices E Maximum memory size of 2GB Super UO E Chip ITE 178705 Slots E Three 32 bit PCI bus masterslots E One AGP 4X 8X slot AGP 4X only supports 1 5v AGP electricals E One CNR slot n Board IDE Supports four IDE disk drives E Supports RO Mode 0 4 Ultra DMA 33 66 100 133 Bus Master Mode LAN E Chip VIA VT6103 E Supports 10 Mb s and 100 Mb s auto negotiation E Hak Full duplex capability On Board AC 97 Sound Codec E Chip CMI9739A CM9761A for v3 2 amp above E Compliant with AC 97 specification E AC99 2 2 interfacef or CMI9739A AC99 2 3 interface for CMI9761A E Supports 6channes E Supports stereo microphone for CMI9761A On Board Peripherals a Rearside E 2 serial ports 1 parallel port SPP EPP ECP mode Audio ports in vertical position 1 LAN jack PS 2 mouse and PS 2 keyboard 2 USB2 0 ports 4 USB2 0 ports for v3 2 1 vertical audio port b HontSide E 1 floppy port suppots 2 FDDs with 360K 720K 1 2M 1 44M and 2 88Mbytes E 4 USB2 0 ports E front audio header Dimensions E Micro ATX Form Factor 24 5 X 22 5cm W XL B BIOS amp Software BIOS Award legal Bios APM1 2 ACPI USB Function Software ar ET an Supports Warpspeeder 9th Touch FLASHERTM WinFlasher Qf ers thehighest performarce for Win
39. ted in this user manual will changeaccordingto your motherboard on hand WarpSpeeder includes 1 tray icon and 5 panels 1 Tray Icon Whenever the Tray Icon utility is launched it wil display a little tray icon onthe right side of Windows Taskbar EO V 1133 AM 18 This utiliy is responsible f or conveniently invoking WarpSpeederTM Utility Youcan use the mouse by clicking the left buttonin orderto inv oke WarpSpeeder M directly from the little tray icon oryou can right click the little tray icon to pop up apopup menu as following figure The Laurch Utility tem in the popup menu has the same function as mouse left click on tray icon and Exit item will close Tray Icon utility f selected Lanuch Utility Exit fx ift Rial 2 Main Panel If you clik the tray icon WarpSpeeder uility will be inv oked Please ref er do the following figure the utility s f ist windowy ou willsee is Main Panel Main Panel contains features as follows a Display the CPU Speed CPU external clock Memory clock AGP clock and PCI clock information b Contains About Voltage Overclock and Hardware Monitor Buttons for invoking respective panels c With a userfriendy Status Animation it can represent 3 overclock percentage stages Duck walking gt overclock percentage from 100 110 96 Duck running gt overclock percentage from 110 120 Duck burning gt overclock percentage from 12096 above 19
40. umeric value or make changes Decrease the numeric value or make changes Main Menu Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu Exit Current page and return to Main Menu General help on Setup navigation keys Load previous values from CMOS Load the optimized defaults Save all the CMOS changes and exit U8799 BIOS Setup 1 Main Menu Once you enter Award BIOSIM CMOS Setup Utility the Main Menu will appear on the screen The Main Menu allows you to select from several setup functions Use the arrow keys to select among the items and press Enter to accept and enter the sub menu 6 WARNING The information about BIOS defaults on manual Figure 1 2 3 4 5 6 7 8 9 is just for reference please refer to the BIOS installed on board for update information W Figure 1 Main Menu Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features gt Frequency Voltage Control Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password Power Management Setup Save amp Exit Setup PnP PCI Configurations Exit Without Saving PC Health Status Upgrade BIOS Select Item Time Date Hard Disk Type Standard CMOS Features This submenu contains industry standard configurable options Advanced BIOS Features This submenu allows you to configure enhance
41. ure Show you the current CPU temperature Current CPUFAN Speed This field displays the current CPUFAN speed Current SYSFAN Speed This field displays the current speed SYSTEM fan 28 U8799 BIOS Setup Show H W Monitor in POST If you computer contain a monitoring system it will show PC health status during POST stage The item offers several delay time to select you want The Choices Enabled default Disabled 29 U8799 BIOS Setup 9 Frequency Control W Figure 9 Frequency Control CPU Voltage Default DDR Voltage zy VI Auto Detect PCI DIMM Clk Enabled Spread Spectrum Enabled CPU Clock 100MHz Menu Level CPU Clock Ratio The Choices 8 X default 9X 10X 11X 12X 13X 14 X 15X 16X 17X 18X 19X 20 X 21 X 22 X 23 X CPU Voltage This item allows you to select CPU Voltage Regulator The Choices Default default 1 7 3 4 5 1 DDR Voltage This item allows you to select DDR Voltage Regulator The Choices 2 5V Default 2 6V 2 7V 2 8V Auto Detect PCI DIMM Clk This item allows you to enable disable auto Detect PCI Clock The Choices Enabled default Disabled Spread Spectrum This item allows you to enable disable the Spread Spectrum function The Choices Enabled default Disabled 30 U8799 BIOS Setup CPU Clock This item allows you to select CPU Host Clock The Choices 100MHz Min default 132M Hz Max If
42. ures are implemented via the System Management Interrupt SMI Sleep and Suspend power management modes are supported This AWARD BIOS can manage power to the hard disk drives and video monitors ACPI Support Award ACPI BIOS support Version 1 0 of Advanced Configuration and Power interface specification ACPI It provides ASL code for power management and device configuration capabilities as defined in the ACPI specification developed by Microsoft Intel and Toshiba U8799 BIOS Setup PCI Bus Support This AWARD BIOS also supports Version 2 1 of the Intel PCI Peripheral Component Interconnect local bus specification DRAM Support DDR DRAM Double Data Rate Synchronous DRAM are supported Supported CPUs This AWARD BIOS supports the Intel Pentium 4 CPU Using Setup In general you use the arrow keys to highlight items press Enter to select use the lt PgUp gt and lt PgDn gt keys to change entries press F1 for help and press lt Esc gt to quit The following table provides more detail about how to navigate in the Setup program by using the keyboard Keystroke Function Up arrow Move to previous item Down arrow Move to nextitem Left arrow Move to the item on the left menu bar Right arrow Move to the item on the right menu bar Move Enter Move to the item you desired PgUp key Increase the numeric value or make changes PgDn key Decrease the numeric value or make changes Increase the n
43. y System A password is required for the system to boot and is also required to access the Setup Utility Setup default A password is required to access the Setup Utility only This will only apply if passwords are set from the Setup main menu 10 U8799 BIOS Setup OS Select For DRAM gt 64MB A choice other than Non OS2 is only used for OS2 systems with memory exceeding 64MB The Choices Non OS2 default OS2 Video BIOS Shadow Determines whether video BIOS will be copied to RAM for faster execution Enabled default Optional ROM is enabled Disabled Optional ROM is disabled Summary Screen Show This item allows you to enable disable the summary screen Summary screen means system configuration and PCI device listing The Choices Enabled Disabled default 11 U8799 BIOS Setup 4 Advanced Chipset Features This submenu allows you to configure the specific features of the chipset installed on your system This chipset manage bus speeds and access to system memory resources such as DRAM It also coordinates communications with the PCI bus The default settings that came with your system have been optimized and therefore should not be changed unless you are suspicious that the settings have been changed incorrectly W Figure 4 Advanced Chipset Setup DRAM Clock Drive Control Press Enter AGP amp P2P Bridge Control Press Enter CPU amp PCI Bus Control Press Enter Menu Level ke M
Download Pdf Manuals
Related Search