Home
Biostar M7VIT BIOS Owner's Manual
Contents
1. BIOS attempt to load the operating system from the devices in the sequence selected in these items The Choices Floppy LS120 HDD 0 SCSI CDROM HDD 1 HDD 2 HDD 3 ZIP100 LAN Disabled Swap Floppy Drive For systems with two floppy drives this option allows you to swap logical drive assignments The Choices Disabled default Enabled Boot Up Floppy Seek Enabling this option will test the floppy drives to determine if they have 40 or 80 tracks Disabling this option reduces the time it takes to boot up The Choices Enabled Disabled default M7VIT BIOS Setup Cache amp Shadow Setu This item allows you to setup cache amp shadow setup CPU Internal Cache Depending on the CPU chipset in use you may be able to increase memory access time with this option Enabled default Enable cache Disabled Disable cache External Cache This option enables or disables Level 2 secondary cache on the CPU which may improve performance Enabled default Enable cache Disabled Disable cache CPU L2 Cache ECC Checking This item allows you to enable disable CPU L2 Cache ECC Checking The Choices Enabled default Disabled Video BIOS Shadow Determines whether video BIOS will be copied to RAM for faster execution Enabled default Optional ROM is enabled Disabled Optional ROM is disabled Virus Warning This option allows you to choose the Virus Warning feature that is used to protect the IDE Hard Disk b
2. Disabled IRQ10 Reserved Disabled IRQ11 Reserved Disabled IRQ12 PS 2 Mouse Enabled IRQ13 Coprocessor Enabled IRQ14 Hard Disk Enabled IRQI5 Reserved Disabled 24 M7VIT BIOS Setup 7 PnP PCI Configurations This section describes configuring the PCI bus system PCI or Personal Computer Interconnect is a system which allows I O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings m Figure 7 PnP PCI Configurations 0 0 PNP OS Installed Item Help Reset Configuration Data Resources Controlled By PCI VGA Palette Snoop Assign IRQ For VGA Assign IRQ For USB PNP OS Installed When set to YES BIOS will only initialize the PnP cards used for the boot sequence VGA IDE SCSI The rest of the cards will be initialized by the PnP operating system like Window 95 When set to NO BIOS will initialize all the PnP cards For non PnP operating systems DOS Netware this option must set to NO The Choices No default Yes Reset Configuration Data The system BIOS supports the PnP feature which requires the system to record which resources are assigned and protects resources from conflict Every peripheral device has a node which is called ESCD This node records which resources
3. Power Management three of which have fixed mode settings Min Power Saving Minimum power management Suspend Mode 1 hr HDD Power Down 15 min Max Power Saving Maximum power management only available for sl CPU s Suspend Mode 1 min HDD Power Down 1 min User Defined default Allows you to set each mode individually When not disabled each of the ranges are from 1 min to 1 hr except for HDD Power Down which ranges from 1 min to 15 min and disable HDD Power Down When enabled the hard disk drive will power down and after a set time of system inactivity All other devices remain active The Choices Disabled default 1 Min 2 Min 3 Min 4 Min 5 Min 6 Min 7 Min 8 Min 9 Min 10 Min 11 Min 12 Min 13 Min 14 Min 15Min Suspend Mode The item allows you to select the suspend type under ACPI operating system The Choices Disabled default 1 Min 2 Min 4 Min 6 Min 8 Min 10 Min 20 Min 30 Min 40 Min 1 Hour Video Off Option This field determines when to activate the video off feature for monitor power management The Choices Suspend gt Off default Always on Video Off Method This option determines the manner in which the monitor is goes blank V H SYNC Blank default This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer Blank Screen 22 M7VIT BIOS Setup This option only writes blanks t
4. RAM Cacheable DRAM Clock Drive Control To control the Clock Drive If you highlight the literal Press Enter next to the DRAM Clock Drive Control label and then press the enter key it will take you a submenu with the following options DRAM Clock This item determines DRAM clock following 100MHz 133MHz 166MHz or By SPD The Choices 100MHz 133MHz By SPD default 166MHz 12 M7VIT BIOS Setup DRAM Timing This item determines DRAM clock timing follow SPD or not The Choices Auto By SPD default Manual Turbo Ultra DRAM CAS Latency When DRAM is installed the number of clock cycles of CAS latency depends on the DRAM timing The Choices 2 5 default 2 Bank Interleave This item allows you to enable or disable the bank interleave feature The Choices Disabled default 2 bank 4 bank Precharge to Active Trp This items allows you to specify the delay from precharge command to activate command The Choices 2T 3T default Active to Precharge Tras This items allows you to specify the minimum bank active time The Choices 7T default 6T Active to CMD Tred Use this item to specify the delay from the activation of a bank to the time that a read or write command is accepted The Choices 2T 3T default DRAM Burst Length The Choices 4 default 8 DRAM Queue Depth This item permits to place the depths of the memory The deeper the depth is the better is t
5. are assigned to it The system needs to record and update ESCD to the memory locations These locations 4K are reserved in the system BIOS If the Disabled default option is chosen the system s ESCD will update only when the new configuration varies from the last one If the Enabled 25 M7VIT BIOS Setup option is chosen the system is forced to update ESCDs and then is automatically set to the Disabled mode The above settings will be shown on the screen only if Manual is chosen for the resources controlled by function Legacy is the term which signifies that a resource is assigned to the ISA Bus and provides non PnP ISA add on cards PCI ISA PnP signifies that a resource is assigned to the PCI Bus or provides for ISA PnP add on cards and peripherals The Choices Disabled default Enabled Resources Controlled By By Choosing Auto ESCD default the system BIOS will detect the system resources and automatically assign the relative IRQ and DMA channel for each peripheral By Choosing Manual the user will need to assign IRQ amp DMA for add on cards Be sure that there are no IRQ DMA and I O port conflicts IRQ Resources This submenu will allow you to assign each system interrupt a type depending on the type of device using the interrupt When you press the Press Enter tag you will be directed to a submenu that will allow you to configure the system interrupts This is only configurable
6. when Resources Controlled By is set to Manual IRQ 3 assigned to PCI Device IRQ 4 assigned to PCI Device IRQ 5 assigned to PCI Device IRQ 7 assigned to PCI Device IRQ 9 assigned to PCI Device IRQ 10 assigned to PCI Device IRQ 11 assigned to PCI Device IRQ 12 assigned to PCI Device IRQ 14 assigned to PCI Device IRQ 15 assigned to PCI Device PCI VGA Palette Snoop Choose Disabled or Enabled Some graphic controllers which are not VGA compatible take the output from a VGA controller and map it to their display as a way to provide boot information and VGA compatibility However the color information coming from the VGA controller is drawn from the palette table inside the VGA controller to generate the proper colors and the graphic controller needs to know what is in the palette of the VGA controller To do this the non VGA graphic controller watches for the Write access to the VGA palette and registers the snoop data In PCI based systems where the VGA controller is on the PCI bus and a non VGA graphic controller is on an ISA bus the Write Access to the palette will not show up on the ISA bus if the PCI VGA controller responds to the Write 26 M7VIT BIOS Setup In this case the PCI VGA controller should not respond to the Write it should only snoop the data and permit the access to be forwarded to the ISA bus The non VGA ISA graphic controller can then snoop the data on the ISA bus Unless you have the above situatio
7. IOS Setup The Choices SPP default Using Parallel port as Standard Printer Port EPP Using Parallel Port as Enhanced Parallel Port ECP Using Parallel port as Extended Capabilities Port ECP EPP Using Parallel port as ECP amp EPP mode EPP Mode Select Select EPP port type 1 7 or 1 9 The Choices EPP 1 7 default EPP1 9 ECP Mode Use DMA Select a DMA Channel for the port The Choices 3 default 1 Game Port Address Game Port I O Address The Choices 201 default 209 Disabled Midi Port Address Midi Port Base I O Address The Choices 330 default 300 290 Disabled Midi Port IRQ This determines the IRQ in which the Midi Port can use The Choices 5 10 default Init Display First With systems that have multiple video cards this option determines whether the primary display uses a PCI Slot or an AGP Slot The Choices PCI Slot default AGP OnChip USB Controller This option should be enabled if your system has a USB installed on the system board You will need to disable this feature if you add a higher performance controller The Choices All Enabled default All Disabled 1 amp 2 USB Port 2 amp 3 USB Port 1 amp 3 USB Port 1 USB Port 2 USB Port 3 USB Port USB Keyboard Support Enables support for USB attached keyboards The Choices Disabled default Enabled USB Mouse Support Enables support for USB attached mouse The Choices Disabled default Enabled 19 M7VIT BIOS
8. M7VIT BIOS Setup BIOS EE l Main Mem EVERE aninaaiindes sang in anak Nakaka nane van aerate 3 2 Standard CMOS Features niaaa E E a AO 6 3 Advanced BIOS Features iaee T is 9 4 Advanced Chipset Features erine nore a E E 12 5 Integrated Peripherals 2 sssenia decisive nisust nekorisne niesienia 16 6 Power Management Setup 21 7 PnP PCI Confbeurapons 25 SPE Health Statusen sissies AE esas egene geed hs 28 9 Frequency Voltage Control 30 M7VIT BIOS Setup BIOS Setup Introduction This manual discussed Award Setup program built into the ROM BIOS The Setup program allows users to modify the basic system configuration This special information is then stored in battery backed RAM so that it retains the Setup information when the power is turned off The Award BIOS installed in your computer system s ROM Read Only Memory is a custom version of an industry standard BIOS This means that it supports Intel Pentium 4 processor input output system The BIOS provides critical low level support for standard devices such as disk drives and serial and parallel ports Adding important has customized the Award BIOS but nonstandard features such as virus and password protection as well as special support for detailed fine tuning of the chipset controlling the entire system The rest of this manual is intended to guide you through the process of configuring your system using Setup Plug and Play Support These AWARD BIO
9. S supports the Plug and Play Version 1 0A specification ESCD Extended System Configuration Data write is supported EPA Green PC Support This AWARD BIOS supports Version 1 03 of the EPA Green PC specification APM Support These AWARD BIOS supports Version 1 1 amp 1 2 of the Advanced Power Management APM specification Power management features are implemented via the System Management Interrupt SMI Sleep and Suspend power management modes are supported Power to the hard disk drives and video monitors can be managed by this AWARD BIOS ACPI Support Award ACPI BIOS support Version 1 0 of Advanced Configuration and Power interface specification ACPI It provides ASL code for power management and device configuration capabilities as defined in the ACPI specification developed by Microsoft Intel and Toshiba M7VIT BIOS Setup PCI Bus Support This AWARD BIOS also supports Version 2 1 of the Intel PCI Peripheral Component Interconnect local bus specification DRAM Support DDR SDRAM Double Data Rate Synchronous DRAM are supported Supported CPUs This AWARD BIOS supports the AMD CPU Using Setup In general you use the arrow keys to highlight items press lt Enter gt to select use the lt PgUp gt and lt PgDn gt keys to change entries press lt F1 gt for help and press lt Esc gt to quit The following table provides more detail about how to navigate in the Setup program by using the keyboard Right arro
10. Setup IDE HDD Block Mode Block mode is also called block transfer multiple commands or multiple sector read write If your IDE hard drive supports block mode most new drives do select Enabled for automatic detection of the optimal number of block mode most new drives do select Enabled for automatic detection of the optimal number of block read write per sector where the drive can support The Choices Enabled default Disabled 20 M7VIT BIOS Setup 6 Power Management Setup The Power Management Setup Menu allows you to configure your system to utilize energy conservation and power up power down features E Figure 6 Power Management Setup ACPI function Enabled ACPI Suspend Type Power Management Option HDD Power Down Suspend Mode Video Off Option Video Off Method MODEM Use IRQ Sof t Off by PWRBTN TRQ Event Activity Detect ACPI function This item displays the status of the Advanced Configuration and Power Management ACPI The Choices Enabled default Disabled ACPI Suspend Type The item allows you to select the suspend type under the ACPI operating system The Choices S1 POS default Power on Suspend S3 STR Suspend to RAM S1 83 POS STR Power Management This category allows you to select the type or degree of power saving and is directly related to the following modes 1 HDD Power Down 2 Suspend Mode 21 M7VIT BIOS Setup There are four options of
11. abled you can reserve an area of system memory for ISA adapter ROM When this area is reserved it cannot be cached Refer to the user documentation of the peripheral you are installing for more information The Choices Disabled default 15M 16M System BIOS Cacheable Selecting the Enabled option allows caching of the system BIOS ROM at FO000h FFFFFh which can improve system performance However any programs writing to this area of memory will cause conflicts and result in system errors The Choices Enabled Disabled default Video RAM Cacheable Enabling this option allows caching of the video RAM resulting in better system performance However if any program writes to this memory area a system error may result The Choices Enabled Disabled default 15 M7VIT BIOS Setup 5 Integrated Peripherals m Figure 5 Integrated Peripherals VIA OnChip IDE Device Press Enter VIA OnChip PCI Device SuperI0 Device Init Display First OnChip USB Controller USB Keyboard Support USB House Support IDE HDD Block Mode VIA OnChip IDE Device The chipset contains a PCI IDE interface with support for two IDE channels Select Enabled to activate the first and or second IDE interface If you install a primary and or secondary add in IDE interface select Disabled to deactivate an interface If you highlight the literal Press Enter next to the Onchip IDE Control label an
12. ay and PCI options PC Health Status This submenu allows you to monitor the hardware of your system Frequency Voltage Control This submenu allows you to change CPU Vcore Voltage and CPU PCI clock However this function is strongly recommended not to use Not properly change the voltage and clock may cause CPU or M B damage Load Optimized Defaults This selection allows you to reload the BIOS when the system is having problems particularly with the boot sequence These configurations are factory settings optimized for this system A confirmation message will be displayed before defaults are set Load Optimized Defaults Y N N Set Supervisor Password Setting the supervisor password will prohibit everyone except the supervisor from making changes using the CMOS Setup Utility You will be prompted with to enter a password Enter Passwor M7VIT BIOS Setup Set User Password If the Supervisor Password is not set then the User Password will function in the same way as the Supervisor Password If the Supervisor Password is set and the User Password is set the User will only be able to view configurations but will not be able to change them Enter Password Save amp Exit Setup Save all configuration changes to CMOS memory and exit setup Confirmation message will be displayed before proceeding SAVE to CMOS and EXIT Y N Exit Without Saving Abandon all changes made during the current ses
13. d or to use the CMOS Setup Utility System A password is required for the system to boot and is also required to access the Setup Utility Setup default A password is required to access the Setup Utility only This will only apply if passwords are set from the Setup main menu MPS Version Control For OS The BIOS supports version 1 1 and 1 4 of the Intel multiprocessor specification Select version supported by the operation system running on this computer The Choices 1 4 default 1 1 OS Select For DRAM gt 64MB A choice other than Non OS2 is only used for OS2 systems with memory exceeding 64MB The Choices Non OS2 default OS2 Summary Screen Show This item allows you to enable disable display the Summary Screen Show The Choices Disabled default Enabled 11 M7VIT BIOS Setup 4 Advanced Chipset Features This submenu allows you to configure the specific features of the chipset installed on your system This chipset manage bus speeds and access to system memory resources such as DRAM It also coordinates communications with the PCI bus The default settings that came with your system have been optimized and therefore should not be changed unless you are suspicious that the settings have been changed incorrectly E Figure 4 Advanced Chipset Setup DRAM Clock Drive Control Press Enter Item Help AGP amp P2P Bridge Control CPU amp PCI Bus Control Memory Hole System BIOS Cacheable Video
14. d then press the enter key it will take you a submenu with the following options OnChip IDE Channel 0 1 The motherboard chipset contains a PCI IDE interface with support for two IDE channels Select Enabled to activate the first and or second IDE interface Select Disabled to deactivate an interface if you are going to install a primary and or secondary add in IDE interface The Choices Enabled default Disabled IDE Prefetch Mode The onboard IDE drive interfaces supports IDE prefetching for faster drive access If the interface does not support prefetching If you install a primary and or secondary add in IDE interface set this option to Disabled The Choices Enabled default Disabled 16 M7VIT BIOS Setup IDE Primary Secondary Master Slave PIO The IDE PIO Programmed Input Output fields let you set a PIO mode 0 4 for each of the IDE devices that the onboard IDE interface supports Modes 0 through 4 provides successively increased performance In Auto mode the system automatically determines the best mode for each device The Choices Auto default Mode0 Model Mode2 Mode3 Mode4 IDE Primary Secondary Master Slave UDMA Ultra DMA 100 functionality can be implemented if it is supported by the IDE hard drives in your system As well your operating environment requires a DMA driver Windows 95 OSR2 or a third party IDE bus master driver If your hard drive and your system soft
15. ect an address and corresponding interrupt for the first and second serial ports The Choices Disabled 3F8 IRQ4 default 2F8 IRQ3 3E8 IRQ4 2E8 IRQ3 Auto Onboard Serial Port 2 Select an address and corresponding interrupt for the first and second serial ports The Choices Disabled 2F8 IRQ3 default 3F8 IRQ4 3E8 IRQ4 2E8 IRQ3 Auto UART Mode Select This item allows you to determine which Infra Red IR function of onboard I O chip The Choices Normal default AS KIR IrDA RxD TxD Active This item allows you to determine which Infrared IR function of onboard I O chip The Choices Hi Lo default Hi Hi Lo Hi Lo Lo IR Transmission Delay This item allows you to enable disable IR transmission delay The Choices Enabled default Disabled UR2 Duplex Mode Select the value required by the IR device connected to the IR port Full duplex mode permits simultaneous two direction transmission Half duplex mode permits transmission in one direction only at a time The Choices Half default Full Use IR Pins Consult your IR peripheral documentation to select the correct setting of the TxD and RxD signals The Choices IR Rx2Tx2 default RxD2 TxD2 Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I O Address The Choices 378 IRQ7 default 278 IRQ5 3BC IRQ7 Disabled Parallel Port Mode The default value is SPP 18 M7VIT B
16. his function The Choices 4 level default 2 level 3 level DRAM Command Rate This item controls clock cycle that must occur between the last valid write operation and the next command The Choices 1T Command 2T Command default Write Recovery Time The Choices 3T default 2T DRAM tWTR The Choices 3T default 1T 13 M7VIT BIOS Setup AGP amp P2P Bridge Control If you highlight the literal Press Enter next to the AGP amp P2P Bridge Control label and then press the enter key it will take you a submenu with the following options AGP Aperture Size Select the size of the Accelerated Graphics Port AGP aperture The aperture is a portion of the PCI memory address range dedicated for graphics memory address space Host cycles that hit the aperture range are forwarded to the AGP without any translation The Choices 64M 256M 128M default 32M 16M 8M 4M AGP Mode This item allows you to select the AGP Mode The Choices 4X default 2X 1X AGP Driving Control By choosing Auto the system BIOS will the AGP output Buffer Drive strength P Ctrl by AGP Card By choosing Manual it allows user to set AGP output Buffer Drive strength P Ctrl by manual The Choices Auto default Manual AGP Driving Value While AGP driving control item set to Manual it allows user to set AGP driving The Choices DA default AGP Fast Write The Choices Enabled Disabled defau
17. l awaken a system which has been powered down The Choices LPT COM default COM LPT NONE HDD amp FDD When this option is set to On any event occurring on a hard drive or a floppy drive will awaken a system which has been powered down The Choices On default Off 23 M7VIT BIOS Setup PCI Master When set to On you need a LAN add on card which supports the power function It should also support the wake up on LAN jump The Choices Off default On PowerOn by PCI Card When you select Enabled a PME signal from PCI card returns the system to Full ON state The Choices Disabled default Enabled Wake Up On LAN Ring To use this function you need a LAN add on card which support power on function It should also support the wake up on LAN jump Disabled default Wake up on LAN Ring not supported Enabled Wake up on LAN Ring supported Modem Ring Resume The Choices Disabled default Enabled RTC Alarm Resume When Enabled you can set the date and time at which the RTC real time clock alarm awakens the system from Suspend mode The Choices Enabled Disabled default IRQs Activity Monitoring Press Enter to access another sub menu used to configure the different wake up events i e wake on LPT amp COMM activity Primary INTR On IRQ3 COM2 Enabled IRQ4 COM1 Enabled IRQS LPT2 Enabled IRQ6 Floppy Disk Enabled IRQ7 LPT1 Enabled IRQ8 RTC Alarm Disabled IRQ9 IRQ2 Redir
18. lt AGP Master 1 WS Write When Enabled writes to the AGP Accelerated Graphics Port are executed with one wait states The Choices Disabled default Enabled AGP Master 1 WS Read When Enabled read to the AGP Accelerated Graphics Port are executed with one wait states The Choices Disabled default Enabled DBI Output for AGP Trans The Choices Disabled default Enabled CPU amp PCI Bus Control If you highlight the literal Press Enter next to the CPU amp PCI Bus Control label and then press the enter key it will take you a submenu with the following options 14 M7VIT BIOS Setup PCI1 Master 0 WS Write When enabled writes to the PCI bus are executed with zero wait states The Choices Enabled default Disabled PCI2 Master 0 WS Write When enabled writes to the AGP bus are executed with zero wait states The Choices Enabled default Disabled PCI1 Post Write When Enabled CPU writes are allowed to post on the PCI bus The Choices Enabled default Disabled PCI2 Post Write When Enabled CPU writes are allowed to post on the AGP bus The Choices Enabled default Disabled VLink 8X Support The Choices Enabled default Disabled PCI Delay Transaction The chipset has an embedded 32 bit posted write buffer to support delay transactions cycles Select Enabled to support compliance with PCI specification The Choices Enabled default Disabled Memory Hole When en
19. n you should disable this option Disabled default Disables the function Enabled Enables the function Assign IRQ For VGA This item allows the users to choose which IRQ to assign for the VGA The Choices Enabled default Disabled Assign IRQ For USB This item allows the users to choose which IRQ to assign for the USB The Choices Enabled default Disabled 27 M7VIT BIOS Setup 8 PC Health Status m Figure 8 PC Health Status Shutdown Temperature Disabled Show H Monitor in POST Previo e 0 ed De Current CPU1 Temperature This field displays the current temperature of the CPU Current CPUFAN Speed This field displays the current speed of CPU fan Current SYSFAN Speed This field displays the current speed SYSTEM fan CPU Veore 3 3V 5V 12V 12V 5V VBAT V 5VSB V Detect the system s voltage status automatically Shutdown Temperature This item allows you to set up the CPU shutdown Temperature This item only effective under Windows 98 ACPI mode The Choices Disabled default 60 C 140 F 65 C 149 F 70 C 158 F 75 C 167 F 28 M7VIT BIOS Setup Show H W Monitor in POST If your computer contains a monitoring system it will show PC health status during POST stage The item offers several delay time for you to choose The Choices Enabled default Disabled 29 M7VIT BIOS Setup 9 Frequency Voltage Control m Figure 9 Frequency Voltage Co
20. ntrol Phoenix AwardBIOS CMOS Setup Utility Frequency Voltage Control CPU Clock Item TtemHelp Tl Move GE Select ES PU PD Value F1 Save ESC Exit Eil General Help Previous Values F Optimized Defaults CPU Clock This item allows you to select CPU Clock and CPU over clocking If unfortunately the system s frequency that you are selected is not functioning there are two methods of booting up the system Method 1 Clear the COMS data by setting the JCOMS1 2 3 closed as ON status All the CMOS data will be loaded as defaults setting Method 2 Press the lt Insert gt key and Power button simultaneously after that keep on pressing the lt Insert gt key until the power on screen showed This action will boot up the system according to FSB of the processor X It s strongly recommended to set CPU Vcore and clock in default setting If the CPU Vcore and clock are not in default setting it may cause CPU or M B damage 30
21. o the video buffer DPMS Initial display power management signaling The Choices Stop Grant default PwrOn Suspend Modem Use IRQ This determines the IRQ which can be applied in MODEM use The Choices 3 default 4 5 7 9 10 11 NA Run VGABIOS if S3 Resume Choosing Enabled will make BIOS run VGA BIOS to initialize the VGA card when system wakes up from S3 state The system time is shortened if you disable the function but system will need AGP driver to initialize the card So if the AGP driver of the VGA card does not support the initialization feature the display may work abnormally or not function after S3 The Choices Auto Yes default No Soft Off by PWR BTTN Pressing the power button for more than 4 seconds forces the system to enter the Soft Off state when the system has hung The Choices Delay 4 Sec Instant Off default IRQ Event Activity Detect If you highlight the literal Press Enter next to the IRQ Event Activity Detect label and then press the enter key it will take you a submenu with the following options USB Resume from S3 This item allows you to enable or disable USB Resume from S3 The Choices Disabled defautl Enabled VGA When set to On any event occurring at a VGA Port will awaken a system which has been powered down The Choices Off default On LPT amp COM When this option is set to On any event occurring at a COM serial LPT printer port wil
22. oot sector If this function is enabled and an attempt is made to write to the boot sector BIOS will display a warning message on the screen and sound an alarm beep Disabled default Virus protection is disabled Enabled Virus protection is activated Quick Power On Self Test Enabling this option will cause an abridged version of the Power On Self Test POST to execute after you power up the computer Enabled default Enable quick POST Disabled Normal POST Boot Up NumLock Status Selects the NumLock State after power on On default Numpad is number keys Off Numpad is arrow keys Gate A20 Option Select if chipset or keyboard controller should control Gate A20 Normal A pin in the keyboard controller 10 M7VIT BIOS Setup controls Gate A20 Fast default Lets chipset control Gate A20 Typematic Rate Settin When a key is held down the keystroke will repeat at a rate determined by the keyboard controller When enabled the typematic rate and typematic delay can be configured Disabled default Enabled Typematic Rate Chars Sec Sets the rate at which a keystroke is repeated when you hold the key down The Choices 6 default 8 10 12 15 20 24 30 Typematic Delay Msec Sets the delay time after the key is held down before it begins to repeat the keystroke The Choices 250 default 500 750 1000 Security Option This option will enable only individuals with passwords to bring the system online an
23. sion and exit setup confirmation message will be displayed before proceeding Quit Without Saving Y N Upgrade BIOS This submenu allows you to upgrade bios BIOS UPDATE UTILITY Y N N M7VIT BIOS Setup 2 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into 10 categories Each category includes no one or more than one setup items Use the arrow keys to highlight the item and then use the lt PgUp gt or lt PgDn gt keys to select the value you want in each item m Figure 2 Standard CMOS Setup Phoenix AwardBIOS CMOS Setup Utility Standard CHOS Features Time hh mm ss IDE Primary Master IDE Primary Slave IDE Secondary Master IDE Secondary Slave Drive A Drive B Video Halt On Tl Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values ptimized Defaults M7VIT BIOS Setup Main Menu Selections This table shows the selections that you can make on the Main Menu Item Options Description Date mm dd yy Set the system date Note that the Day automatically changes when you set the date Set the system internal clock Time IDE Primary Master Options are in its sub Press lt Enter gt to enter the menu sub menu of detailed options IDE Primary Slave Options are in its sub Press lt Enter gt to enter the menu sub menu of detailed options IDE Secondary Master Op
24. tions are in its sub Press lt Enter gt to enter the menu sub menu of detailed options IDE Secondary Slave Options are in its sub Press lt Enter gt to enter the menu sub menu of detailed options Drive A 360K 5 25 in Select the type of floppy Drive B 1 2M 5 25 in disk drive installed in your system 720K 3 5 in 1 44M 3 5 in 2 88M 3 5 in None Video EGA VGA Select the default video CGA 40 device CGA 80 MONO M7VIT BIOS Setup Item Options Description Halt On All Errors Select the situation in which No Errors you want the BIOS to stop All but Keyboard the POST process and All but Diskette notify you All but Disk Key Base Memory Displays the amount of conventional memory detected during boot up Extended Memory Displays the amount of extended memory detected during boot up Total Memory N A Displays the total memory available in the system M7VIT BIOS Setup 3 Advanced BIOS Features m Figure 3 Advanced BIOS Setup Boot Seq amp Floppy Setup Press Enter Cache amp Shadow Setup Virus Warning Quick Power On Self Test Boot Up NumLock Status Gate A20 Option Typematic Rate Setting Security Option MPS Version Control For 0S OS Select For DRAM gt 64MB Summary Screen Show Boot Seq amp Floppy Setup This item allows you to setup boot seq amp Floppy First Second Third Boot Other Device These
25. w Move to the item on the ri Key Increase the numeric value or make changes Decrease the numeric value or make changes Esc key Main Menu Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu Exit Current page and return to Main Menu M7VIT BIOS Setup 1 Main Menu Once you enter Award BIOS CMOS Setup Utility the Main Menu will appear on the screen The Main Menu allows you to select from several setup functions Use the arrow keys to select among the items and press lt Enter gt to accept and enter the sub menu 1 WARNING The information about BIOS defaults on manual Figure 1 2 3 4 5 6 7 8 9 is just for reference please refer to the BIOS installed on board for update information m Figure 1 Main Menu Standard CHOS Features Thre Select Item Standard CMOS Features This submenu contains industry standard configurable options Advanced BIOS Features This submenu allows you to configure enhanced features of the BIOS Advanced Chipset Features This submenu allows you to configure special chipset features M7VIT BIOS Setup Integrated Peripherals This submenu allows you to configure certain IDE hard drive options and Programmed Input Output features Power Management Setup This submenu allows you to configure the power management features PnP PCI Configurations This submenu allows you to configure certain Plug and Pl
26. ware both support Ultra DMA 100 select Auto to enable BIOS support The Choices Auto default Disabled VIA OnChip PCI Device If you highlight the literal Press Enter next to the OnChip PCI Device label and then press the enter key it will take you a submenu with the following options VIA 3058 AC97 Audio This option allows you to control the onboard AC97 audio The Choices Auto default Disabled VIA 3068 MC97 Modem This option allows you to control the onboard MC97 modem The Choices Auto default Disabled VIA 3043 OnChip LAN This option allows you to control the onboard LAN The Choices Enabled default Disabled Onboard LAN Boot ROM This item allows you to enable or disable Onboard LAN Boot ROM The Choices Disabled default Enabled CMI Onboard Audio This item allows you to select enable or disable the Onboard CMI 8738 Audio controller The Choices Enabled default Disabled Super IO Device If you highlight the literal Press Enter next to the Super IO Device label and then press the enter key it will take you a submenu with the following options Onboard FDC Controller Select Enabled if your system has a floppy disk controller FDC installed on the 17 M7VIT BIOS Setup system board and you wish to use it If install and FDC or the system has no floppy drive select Disabled in this field The Choices Enabled default Disabled Onboard Serial Port 1 Sel
Download Pdf Manuals
Related Search
Related Contents
10C - 2.4GHz - Aeromodelli HL100F API for MX100/DARWIN User`s Manual Omega Engineering DPG1001B User's Manual COLA LISTA PARA EMPAPELAR VINILO/PAPEL ASRock Z77 Quick Start Manual Sony CDX-GT63UIW CD Player User Manual Your 350 Watt Power Inverter converts 12 Fujitsu MYUSBS A910 4 GB Ultralux Torchiere User Manual Copyright © All rights reserved.
Failed to retrieve file