Binatone SYMPHONY 2200 User's Manual
Contents
1. 1 3 4 and 6 are free 2 and 5 are already assigned to other handsets 6 Key ina free handset number gt After a moment the display should show the handsets name and number If registration fails Try again making sure you begin step 2 as soon as Registration tone starts 20 Interference If the sound quality gets worse as you move around while on a call this is probably due to interference between the handset and the base unit perhaps because you are too near to another phone or other electrical equipment M ove to a different position to clear the interference If you do not move your call may be cut off Radio interference in the environment may occasionally cause a short break in the link between the handset and the base unit while you are on a call The handset s display will flash briefly while the unit automatically changes to a different channel to restore the link Keeping the batteries charged When you don t need to carry your handsets around for example at night leave them on the base unit or charger pod to keep the batteries charged Whenever the battery charge level symbol on the display shows nearly empty replace the handset on the base unit or charger pod Out of range warning If you hear a warning tone during a call and or the sound in the earpiece becomes faint or distorted you may be going out of range of the base unit Move nearer to the base unit within 20 seconds until2. To stop the ringing Press the HANDSET LOCATOR button again or press any button on any handset To make an intercom call 1 Pressthe INTERCOM button on the handset EITHER key in a handset number 1 to 6 depending on how many handsets are registered OR key in 9 to call all registered handsets gt If you called a handset it rings and its display shows INT and your handset number To answer the intercom call 3 Press the PHONE OK To end the intercom call 4 Press the HANG UP C button on the handset To transfer a call 1 Make or answer an outside call using the handset 2 Briefly press the INTERCOM button then key in a handset number or press 9 to call all handsets button on the ringing handset 17
3. UU Rh WN EP FP FP FP SP a ou BR WN FE O Pressing buttons on your phone m When the instructions in this user guide tell you simply to press a button this means that you should press the button briefly then release it m When the instructions tell you to press and hold a button this means you should keep the button pressed until the display changes and or you hear a tone 32 Ver 2 Jul 07 12 Baby Call With Baby Call babysitter s call tumed on the handset will automatically dial a specified number when any button except PROG is pressed Before you turn Baby Call on you must programme the Baby Call phone number to be dialled With Baby Call turned on the handset can t be used for calling Emergency e Services Make sure there s another handset or phone available for emergencies 1 Press the button then A gt BABYCALL 2 Press q button then v gt NUMBER 3 Press 4 Keyin the phone number and press to confirm gt If a Baby Call number is already programmed use to delete 5 Press to goto ON OFF 6 Press to select Tick ON or Cross OFF 7 Press and hold to go back Stand by mode When Baby Call is turned on the number is shown on the display with a ckj symbol 2 on the top line To turn Baby Call off Press the Menu Press the A or V button to display BABYCALL Press the PHONE OK h WN Pe Press the PHONE OK g to display a cross next to GN OFF M ak
4. failure 13 Operational notes Electrical safety m DON T let the base unit get wet Electrical equipment can cause serious injury if used while you are wet or standing in water m If the base unit ever falls into water DON T retrieve it until you have unplugged the power lead from the mains and the telephone line plug from the telephone socket then pull it out by the unplugged cables m NEVER use your Symphony2200 outdoors during a thunderstorm unplug the base unit from the telephone line and the mains socket when there are storms in your area Damage caused by lightning is not covered by the guarantee Siting the base unit and charger pod The base unit and charger pod should each be placed on a level surface in a position where m the mains adapter plug will reach an easily accessible 230 V AC switched mains supply socket never try to lengthen the mains power cable m the telephone line cable will reach your telephone line socket or extension socket base unit only charger pods have no connection to the telephone line m it isnot close to another telephone this can cause radio interference during calls m it isnot close to a sink bath or shower or anywhere else where it might get wet m it isnot close to other electrical equipment fridges washing machines microwave ovens TVs fluorescent lights etc Radio signals between the handset and the base unit To use your handset and base unit to
5. gt The outside call is put on hold When the user of the other handset unit answers you can talk on an intercom call 3 Press the HANG UP C to transfer the call If the handset user does not answer you can get back to the outside call by pressing the INTERCOM button again You can also shuttle backwards and forwards between the calls To shuttle between two calls When you have both an outside call and an intercom call in progress you can shuttle from one to the other like this D Press the INTERCOM button for one second to speak to each in turn putting the other on hold You can transfer the outside call to the other handset by pressing the HANG UP C p while you re connected to the intercom call If you press the HANG UP C while you re connected to the outside call you will disconnect it To set up a three way conference You can set up a conference using two handsets When you have an outside call either one you ve made or answered or one that s been transferred to you in progress 1 Press the INTERCOM button then key in a handset number gt The outside call is put on hold When the other handset user answers and you have an intercom call in progress 2 Press and hold the STAR button for 2 seconds to set up a three way conference gt Both you and the other user are connected to the outside call To suspend the other handset user from the conference call Press and hold the STAR button for 2 seconds Y
6. the tone stops Otherwise your call may be cut off While you are out of range and you are not on a call the handset s display Shows RANGE GUT and the signal level symbol flashes Before you make a call you must move closer to the base unit until the handset s name and number are displayed and the symbol stops flashing Cleaning and care m Don t clean any part of your Symphony 2200 with benzene thinner or other solvent chemicals this may cause permanent damage which is not covered by the Guarantee When necessary clean it with a damp cloth m Keep your Symphony2200 away from hot humid conditions or strong sunlight The phone is and don t let it get wet m Every effort has been made to ensure high standards of reliability for your Symphony2200 However if something does go wrong pleasaio not try to repair it yourself consult your supplier or the Binatone Help Line 24 15 Guarantee and service The Binatone Symphony 2200 is guaranteed for 12 months from the date of purchase shown on your sales receipt The Guarantee does not cover damage by misuse or negligence or by excessive voltages for example faults on the telephone line or lightning Please keep your sales till receipt this is your guarantee You should also keep the original packaging material In the unlikely event that you need to return your Symphony2200 to our Repair Centre while it is under guarantee there will be a 5
7. to one of the 10 last numbers you dialled 1 Press A or V until the number is shown on the display 2 Press To delete all Caller Display records 1 Press twice The display shows the first Caller Display record 2 Press Gan press _ gt DELETE ALL 4 Press to confirm or press J if you don want to delete all records When there are no more records W he display shows handsset name 6 Tones and volumes To adjust the earpiece volume during a call 1 Press A or V to change the volume Handset ringing melodies To change the ringing melody for incoming external calls Press gt PHONEBOOK Press y gt HSRINGER Press then gt 45 MELODY Press gt MELODY 7 to 8 Press A or V to hear each melody in turn Press to confirm the melody you want Press and hold to go back to standby mode Handset ringing volume You have a choice of eight volume levels including ringer off No uP WN FE 1 Press gt PHONEBOOK 2 Press v gt HS RINGER 3 Press gt HS VOLUME 4 Press q gt 1to lor VOL OFF 5 Press AorV to change the volume 6 Press to confirm 7 Press and hold to go back to standby mode 10 Locking the keypad When the keypad is locked no numbered keys can be pressed so you can t make Calls by mistake To lock the keypad 1 Pressand hold for 4 seconds gt The display shows the 2 symbol when the keypad is locked To unlock the keypad 1 Press and hold for 4 seconds again gt The 2
8. Key in your chosen name Press to confirm Press and hold to go back to standby mode To set the date and time 1 Press then vV gt DATE TIME 2 Press gt DD AM YY key in the date 3 Press gt HKHK AN 4 Press to confirm Auto answer Normally you need to press q to answer an incoming call But with auto answer turned on when your handset is resting on the base unit and it rings for an incoming call you can answer by simply lifting the handset VN a uh W NPBP key in the time To turn auto answer on or off Press then vV gt PHONEBOOK gt HANDSET Press then gt AUTO ANS Press to select Tick ON or Cross OFF Press and hold to go back to standby mode RW NE If you have turned auto answer on don t press the after you ve answered a call by lifting the handset 13 10 Using a muti handset system If you have an Symphony2200 multi handset system you already have up to six handsets registered to your base unit You can register additional handsets altogether up to six handsets per base unit With two or more handsets registered you can m page the handsets from the base unit this is useful if you can t find a handset m make intercom calls from one handset to another m transfer outside calls between handsets m Set up a three way conference call To page all handsets Press the HANDSET LOCATOR button on the base unit gt All registered handsets ring and their displays show PAGING
9. NEBOOK 2 Press v gt BS RINGER 3 Press gt BSVGLUME 4 Press vy gt BSMELODY 5 Press gt MELODY and ito 8 6 Press A or V to hear each melody in turn 7 Press to confirm the melody you want 8 Press and hold to go back to standby mode Base unit ringing volume 1 Press gt PHONEBOOK 2 Press y gt BS RINGER 3 Press gt BS VOLUME 4 Press gt itolor VOL GFF 5 Press A or V _ to change the volume 6 Press to confirm the volume level you want 7 Press and hold to go back to standby mode If you ve set the ringer volume to OFF you won t hear any melody at this point Key tone on off Each time you press a key you hear a tone You can turn this off if you prefer 1 Press then W gt PHONEBOOK gt HANDSET 2 Press q then W gt KEYTONE 3 Press gt ON by Tick or OFF by Cross 4 Press oS to go back to standby mode 11 Provider mode A 1 Press then yw gt HANDSET 2 Press then gt PROV MOD 3 Press to select Tick ON or Cross OFF If you have programmed a prefix code into the base unit you need to tum provider mode on for each handset if you want it automatically to dial the prefix whenever you dial a number beginning with O Dial mode Always leave this setting at TO NE Flash It s very unlikely that you ll need this function and it s usually best to leave the setting at its default MEDIUN But if your Symphony2200 is connected to an extension on a PBX you may need to c
10. annel bandwidth Operating range up to 300 m outdoors up to 50 m indoors Operating time standby 100 hours approx for cordless talking 10 hours approx handset battery charge time 15 hours Temperature Operating 0 2C to 40 2C range Storage 20 C to 60 2C Electrical power CORDLESS HANDSET three AAA size 550 mAH NiMH rechargeable batteries BASE UNIT input 230 V AC 50 Hz output AC 7 5 V 300 mA CHARGER POD input 230 V AC 50 Hz output DC 9 V 300 mA Port specification The 1 port connected to the mains power supply is a SELV port with respect to EN41003 The port connected to the telephone line isa TNV port with respect to EN 41003 PBX compatibility Timed break recall programmable as 85 ms Short 100 ms Medium recommended for most PBX systems or 250 ms Long Pause length 3 seconds Signalling type DTMF dual tone multifrequency also called tone dialling or loop disconnect pulse dialling Network connection This equipment is intended to be used in the UK only Operation on other countries PSTN termination points cannot be guaranteed 29 Contents of this User Guide Where to find it Installation Making and answering calls Memory dialling Caller Display Tones and volumes Call barring Customising your phone Resetting the system Using a muti handset system handset registration Baby Call Operational notes Troubleshooting Guarantee and service Technical details O O N ADA
11. dards m Radio EN 301406 V1 5 1 2003 m EMC EN 301489 1 V 1 6 1 2005 EN 301489 6 V 1 2 1 2002 m Electrical Safely EN 60950 1 2001 All 2004 30 Last Number sym phony 2200 Stylish Digital Cordless Telephone Unpacking your Symphony 2200 In the box are m the cordless handset two handsets with a Twin system three with a Triple system four with a Quad system m the base unit m rechargeable batteries or a battery pack i and a battery compartment cover for Ba CTs the handset D D m a telephone line cable Yaa aer m a mains T one power lead and adapter Sia gus i see If you have an Symphony 2200Twin Triple F Ea or Quad system you should also have m one two or three charger pods m amains power lead and adapter for each one Keep the packaging materials in a safe place in case you later need to transport the unit Keep your sales till receipt which is your guarantee Binatone If you need help The Binatone Help Line is available from 9 00 am to 5 00 pm Monday to Friday on 0845 345 9677 Calls are charged at Local Call rate Important note emergency calls The Symphony 2200is not designed for making emergency calls when the mains power fails So you should make alternative arrangements for access to Emergency Services This means that you should also have a basic phone that does not need mains power connected to your line so that you can make calls during a power
12. e display before keying in the correct ones show memory stored aun WN pme Press the display shows the corresponding number Modify the number if necessary then press You can now carry on modifying numbers to delete an entry all entries from redial list 1 Press then select the number 0o N A 2 Press then w select DELE E or DELETEALL 3 Press to confirm delete an entry or delete all entries To delete an entry or all entries from Phone Book A 1 Press Q then y_ select the number A 2 Press then w select DELETE orp UJELETEALL 3 Press to confirm 7 Call barring Using call barring you can prevent certain types of call being made on your handset There are four levels of Call Barring m NO BAR all calls are allowed This is the default m LOCAL no international calls m NTERNAL you can t make any outgoing calls except emergency 999 calls To bar calls to specified numbers 1 Press then press gt BASE 2 Press then press gt CALL BAR 3 Press to select NU MBERIJor NU MBER the display shows a list of registered handset numbers 4 Keyin a handset number 5 key in the barred number and confirm using 6 Press to select A CTi AT 0 N and confirm using q then key in a handset number 7 Using to select tick ON to activate the call barring or Cross OFF to de activerte it 2 to go back To bar certain type of call 1 Press then press gt BASE 2 Pres
13. e sure the e symbol disappears from the display 22 You need to subscribe to the Caller Display feature from your network service provider You should find contact details on your phone bill Caller Display isn t working The caller may have withheld their number by dialling 141 Or they may be calling from a network that does not transmit the caller s number for example it may be an international call When you store local numbers in the Phone Book include the full dialling code you ll still be charged local rate for making calls Then the name will be shown as part of the Caller Display record Alternatively you can set the national dialling code for your area as a local code The phone is The dial mode may have been accidentally changed dialling very to PULSE Change the setting to TONE slowly you should hear beep tones as you dial I can t make Make sure you re using the correct handset number intercom calls 2 Make sure the handset you re trying to call is switched on and within range Baby Call isn t working When you turn Baby Call on you also need to set the number to be dialled 26 SS Declaration of conformity The Binatone Symphony2200 complies with the essential protective requirements and objectives of m EC R amp TTE Directive 1999 5 EC m EC Directive 2006 95 EC m EC EMC Directive 89 336 EEC and conforms to the following relevant harmonised stan
14. er may be faulty If you cannot make a call the fault may be on the exchange line Contact the service provider the BT engineers on 151 or your cable company If you still cannot identify the cause of the problem contact the Binatone Help Line on 0845 345 9677 27 Waste electrical products must not be disposed of with household waste This equipment should be taken to your local recycling centre for safe treatment 31 1 Where to find it UP A and DOWN Y buttons Press during programming to MENU button move through the menus and options Press to start using Menu Press to move through the Caller functions Display or Redial list Press during a call to adjust the volume in the earpiece or speakerphone R Recall button PHONE OK button Press to begin or answer a phone call When using Menu functions press to confirm your selection Press to switch speakerphone on or Off phone is connected to a PBX or if you use a E network based services Redial C CDS PAUSE button Press once to open alist of the last 10 phone numbers you called Press twice to open the list of Caller Display HANG UP 3 ON OFF C Cancel button Press to end a call this on a PBX oe Ringer Off Y Scroll lt button Press and hold for 4 seconds to tur the ringer off When viewing a number with more than 12 digits press to scroll back along the display CHARGE Light Co
15. gether you must be able to establish a radio link between them Be aware that m Siting the base unit as high as possible will give better results for example in a two storey house the best position may be on the first floor landing m Any large metal object like a refrigerator a mirror or a filing cabinet between the handset and base unit may block the radio signal m Other solid structures like walls may reduce the signal strength 23 PBX use When you first make a call press the REDIAL CDS P Redial and or button for a pause between the outside line access memory dialling code for example 9 and the telephone number You don t work on should later be able to redial the number a PBX When storing numbers in memory you can include the outside line access code e g 9 with each number If your PBX requires you to wait for a second Dial tone before dialling the telephone number press P for a pause between the access code and the number If the fault persists Disconnect all other instruments connected to the same line as the Symphony2200 and see whether you can make a call Disconnect the base unit from the telephone line and plug a different phone into the master telephone socket Try making a call If this works the line is OK If the call does not work and you are using a two way socket adapter remove it and plug a telephone directly into the socket If the call now works the adapt
16. gits press to scroll forward along the display Comes on when you have a connetion Display messages and symbols ve 8 The handset s name Cr NU i the default is HANDSET U L N N J c ene Danaea nUD 5 Ta E The current time The duration of each call is displayed from 20 seconds after you press the PHONE button for a line until 5 seconds after you end the call What the symbols mean Radio link The first symbol on steadily when there s a radio link between signal level the handset and base unit It flashes while the handset is trying to establish a link to the base unit If this symbol flashes while you re on a call move closer to the base unit The second symbol shows the strength of the signal Dx New call You have new Caller Display records Phone Appears when you have a connection to the outside line Flashes when there s an incoming call to be answered even if the ringer is turned off m Phone Comes on when you re storing numbers in the Phone Book and Book when you re making calls to stored numbers X Ringer off Comes on when the handset s ringer is turned off x Mute Comes on when your handset s microphone is muted OO Network If you use a network voice mail service this symbol appears voice mail when you have new messages in your Inbox T Lock Comes on when your handset s keypad is locked una Battery When this shows nearly empty C 11 put the handset on the charge base unit o
17. handling charge While the unit is under Guarantee 1 Disconnect the base unit and charger pod from the telephone line and the mains electricity supply 2 Pack up all parts of your Symphony2200 using the original packaging Remember to include the mains adapters 3 Return the unit to the shop where you bought it making sure you take your sales receipt After the Guarantee has expired If the unit is no longer under Guarantee first follow steps 1 and 2 as for repair under Guarantee Then 3 Call our Service Department on 0845 345 9677 and ask for a quotation of the repair charge and details of where to send your Symphony2200 for repair 4 Make sure you include with your Symphony2200 m your name and address m a cheque or postal order for the value of the repair charge 5 Return your Symphony2200 to the address given by the Service Department This does not affect your statutory rights 28 New call tone When both handsets are on an intercom call and an outside call comes in you will hear NEW CALL TONE over your conversation to tell you that someone is calling you To answer the outside call and end the intercom call Press the R 7 button To answer the outside call and put the intercom call on hold so you can later use shuttle conference or transfer Press INTERCOM button 19 To register to a new base unit If your handset is already registered to a base unit and you want to register it to another o
18. hange this setting also called the recall length to Lons If applicable consult the PBX documentation for details Clear all memories on base Select this to clear all numbers from caller display list 1 Press then 4 gt BASE 2 Press then A gt CLEAR CID gt The display asks CONFIRME 3 Press to confirm to cancel Handset Switch ON OFF 1 Press and hold for 3 seconds 2 The handset will switch ON or OFF 15 2 Installation 1 Choose a suitable site for the base unit telephone 2 Connect the mains power lead and the telephone line cord into the underside of the base unit Use the telephone line cord supplied with your Symphony2200 don t use any other telephone line cord 3 Plug the mains adapter into a 230 V AC 50 Hz mains socket with the switch on the socket set to OFF 4 Install the charger pod s Plug the mains adapter into a 230 V AC 50 Hz mains socket with the switch on the socket set to OFF 5 Switch on at the mains socket s 4 You can edit the number using HANG UP C before storing it if you wish 5 Press to confirm To make a memory call 1 Press Q 2 Press A or V until the display shows the name and number 3 Press to dial the number To modify change a number in memory Press M Press A or V until the display shows the name Press gt ADD Press V TWICE gt MODIFY Press Modify the name if necessary pressing to clear characters from th
19. mes on when the handset s batteries are beingcharged HANDSET LOCATOR PAGE button Press to make all registered handsets ring this is usefull if you ve forgotten where you put a handset to another handset PHONE BOOK l button Keypad Lock O MUTE amp Scroll gt button unlock thekeypad IN USE Light to the telephone line 9 If you have a Broadband line If you connect your telephone to a line with a broadband connection you will need to insert a microfilter not included between the telephone and the telephone line otherwise you may get interference between the telephone and the broadband which could cause problems KES cgo a amp aad a Q E a g GA i SYMPHONY 2200 In a home with broadband every telephone must have a microfilter connected not just the one at the telephone point that your modem is connected to If you need more broadband microfilters contact your broadband supplier 3 Making and answering calls To make a call 1 Keyin the phone number If you make a mistake press 2 to clear digits from the display To clear all digits press and hold 2 2 Press To answer a call When the handset and base unit ring D Press To end a call D Press so that the symbol disappears from the display Last Number Redial To make a repeat call to the last number you dialled 1 Press 2 Press To make a repeat call
20. ne D Follow steps 1 to 5 on page 20 But at step 4 select the lowest numbered free base unit the lowest number that is still flashing To select a base unit If your handset is registered to more than one base unit you can select which one you want it to operate with Or you can leave it to search and establish a link with the nearest free base unit 1 Press the Menu 2 Press the A or V button to display SELBASE 3 Press the PHONE OK gt The display shows a list of the base units to which the handset is registered The currently selected base unit is steady others are flashing 4 Key in a base unit number or 0 to let the handset search for the nearest free base unit and press the PHONE OK to confirm gt The display goes back to SELBASE and you can wait a moment or press HANG UP C to go back To de register a handset 1 Press the Menu 2 Press the A or V button to select JEL 4 5 3 Press the PHONE OK gt The display shows the numbers of all handset registered to the base unit 4 Key in athe number of the handset to be de registered gt The display goes backto DEL H S and you can wait a moment or press HANG UP C to go back to standby mode 21 14 Troubleshooting The Symphony2200 must be serviced by trained engineers NEVER attempt any repairs or adjustments yourself you could make the problem worse and invalidate the Guarantee If you have problems using your Symphony2200 cordless phone refer
21. ou remain connected to the outside call lf the other user has not hung up you can bring her him back into the conference by pressing and hold the STAR button for 2 seconds If you press HANG UP C during the conference call youll leave the other user connected to the outside call If the other user presses HANG UP C you ll be left connected to the outside call 18 11 Handset registration The handsets supplied with your Symphony2200 system are already registered to the base unit You don t need to register them yourself If you buy new handsets separately you ll need to register them Up to six handsets can be registered to each base unit and each handset can be registered to up to four base units To register a new handset 1 Press and hold the HANDSET LOCATOR on the base unit until you hear Registration tone repeated beeps 2 On the handset press the Menu then the A or V button to display REGISTER 3 Press the PHONE OK gt The display shows 85 i234 If any of these numbers is steady not flashing then the handset is already registered to that base unit 4 Press 1 to select base unit number 1 gt The display shows BASE PIN____ 5 Key in the system PIN default 0000 and press the PHONE OK gt The display shows WAIT ____ for afew moments while the handset searches for a base Then it shows a list of handset numbers which are still free on the base unit For example 1 34 6 indicates that numbers
22. r charger pod as soon as possible to charge the level batteries While the batteries are being charged this blinks Speaker Your handset s loudspeaker on phone Muting the mouthpiece D Press and hold key for 4s to mute the mouthpiece While the mouthpiece is muted the person on the other end of the call can t hear you SJ is shown on the display D Press and hold key once again to un mute the mouthpiece Switch the Speakerphone on and off D During a call you can press to switch the speakerphone on the symbol will appear on display D Press when speakerphone on the speakerphone will turn off and the symbol disappear from display The speakerphone won t work if the batteries are low 4 Memory dialling You can store up to 40 numbers in each handset s memory Each number can have up to 24 digits and you can store a name of up to 10 characters with the number To store a number The display shows 1 2 3 4 5 6 7 Press gt PHONEBOOK Press q show first memory stored entry Press gt ADD gt NAME Press Key in the name using the numbered keys Press Key in the number Note if you make a mistake press 2 to clear digits or letters from the display 8 Press You can now carry on storing numbers To store a number from redial list 1 Press then select the number 2 Press gt COPY TO PB 3 Press key in a name then 7 Base unit ringing melody 1 Press gt PHO
23. s number wasn t available the display howsUNKNOWN m The date and time of the call When there have been calls you haven t answered the Xx symbol is shown on the display To check Caller Display records 1 Press twice 2 Press A or V to scroll through the records You ll see either names or numbers If you see a name displayed or number to check Date Time of the call 3 Press to show the Date Time the lt symbol will disappear from the display once you enter the record list To return a call To make a return call to someone who s called you D Press while either the name or number is shown on the display To store a number from Caller Display 1 Press twice then select the number 2 Press gt Bemis 3 Press key in a name then 4 You can edit the number using HANG UP C before storing it if you wish 5 Press to confirm To delete a Caller Display record 1 Press twice then A or V to select the caller display record press 2 Press w twice gt DELETE 3 Press to delete this record or press if you dont want to delete the record When there are no more records the display shows handset name 9 8 Customising your phone Your handset s name The default name shown on your handset s display isS VANTAGE You can change this to anything with up to ten characters Press then W gt HANDSET Press gt HS NAN Press to display the current name Press repeatedly to clear the display
24. s then press gt CALL BAR 3 Press then press gt ere 4 Press then key in a handset number press select N0 BAR U NTERNAHOor LOCAL 5 Using to confirm or to go back to turn call barring off Follow 1 to 4 above setting the level to NGO BAR at step 4 12 Your security PIN You will only need this feature if you plan to set up Call Barring The base unit has a default PIN personal identity number of 0000 You can change it to any number you ll remember with up to eight digits 1 Pres then gt BASE 2 Press gt NEW PIN gt Key in your new PIN and Press to confirm 3 Press to go back 9 Resetting the system twice If you reset the system all features will return to their default settings While you are resetting the system you should disconnect the telephone e line cord from the back of the base unit so you won t be interrupted by incoming calls Reset Base A 1 Press then w gt BASE 2 Press then gt DEFAULT gt CONFIRA 3 Press 4 Press Reset handset 1 Press then gt HANDSET A v then gt DEFAULT 3 Press gt CONFIRM 4 Press gt You hear a confirmation tone 2 Press gt You hear a confirmation tone from the handset 16 6 Fit the batteries in the cordless handsets Insert the three rechargeable batteries as shown Drop in the battery compartment cover then slide it forward until it clicks firmly into place 7 Charge the ba
25. symbol will disappear from display With the keypad locked you cannot make emergency calls to 999 or 112 Clear memories on handset 1 Press Ge then gt HANDSET 2 Press then A gt CLEAR MEN 3 Press gt CONFIRA 4 Press to confirm If you do will clear all numbers from the handset s phonebook and redial list Prefix number This may be useful if you use a dialling prefix to route your long distance calls via a service provider other them the one which supplies your line You can program this prefix into the base unit Then when you tum on Provider Mode on individual handsets the prefix will automatically be dialled out at the beginning of any phone number starting with O 1 Press then V gt BASE 2 Press then Vv gt PREFIX Nun the display shows PREFIX NUMBER and any prefixthats already been set 4 If necessary use to clear digits from the display Then key in the prefix and confirm using q 3 Press 14 You may need this if your Press and hold for 3 seconds to switch the handset on and off Press while editing or using records o Menu functions to cancel what Press while dialling a you re doing and return the number to insert a oe display to Standby mode pause you might need INTERCOM INT button Press to make an intercom call Press to open the Phone Book Press and hold for a moment to lock and Press during a call to mute the mouthpiece When viewing a number with more than 12 di
26. to the separate user guide ALWAYS check first that m you have followed all the steps listed in section 2 to install and set up your Symphony2200 m all connectors are firmly inserted in their sockets m mains power to the base unit telephone is switched on at the socket I can t make or answer Calls If you don t hear Dial tone when you press the handset s PHONE button check whether the base unit or another handset is already using the line If you re using a cordless handset make sure it s within range of the base unit Move closer to the base unit and see if that helps Make sure you re using the telephone line cable that was supplied with your Symphony2200 Other teleohone line cables might not work If the handset s display is blank press the HANG UP C button to switch it on Call barring may be set see section 7 for your handset Check with any other user who may have set it Switch off power at the mains socket wait for a few seconds and then switch back on This may solve the problem The ringer melody may be set to OFF Change it as not ringing described in section 6 Check that the total REN value of all instruments con nected to the line is no more than 4 Disconnect one or more instruments and see if that helps 25 16 Technical details Digital Enhanced Cordless Telecommunications DECT 1 88 to 1 9 GHz bandwidth 20 MHz 1 728 MHz Standard Frequency range Ch
27. tteries for 15 hours Before you use the cordless handsets for the first time it s important to charge the batteries fully You hear a beep when the handset is correctly in position on the charging cradle Leave the handsets on the base unit and charger pod s for 15 hours The bars on the battery level symbol continuously change as the batteries are being charged To keep the batteries charged a oe whenever you don t need to use the 2 handset such as overnight or when ee you go out leave it on the base unit Hie COARSE or charger pod ao 8 Connect the base unit to the telephone line Switch off power at the mains socket Insert the telephone line plug into the socket Switch mains power back on Make sure the mains socket is switched on the phone won t NOTE the charger pod doesn t have a connection to the telephone line work without electrical power 5 Caller Display If you subscribe to this feature from your service provider you can see the phone numbers of people calling you before you answer The Symphony2200 will store the numbers of the last incoming calls Each Caller Display record includes m The caller s name if it s one you ve already stored in your phone s memory m The caller s number up to 20 digits The number won t be displayed if the network they re calling from doesn t support this feature or withheld If the caller
Download Pdf Manuals
Related Search