ASUS VN248H Owner's Manual
Contents
1. Overscan e Vividpixel ASUS Exclusive Technology that brings lifelike visuals for crystal clear and detail oriented enjoyment The adjusting range is from 0 to 100 e ASCR Select ON or OFF to enable or disable dynamic contrast ratio function e Position Adjusts the horizontal position H Position and the vertical position V Position of the image The adjusting range is from 0 to 100 Only available for VGA input e Focus Reduces Horizonal line noise and Vertical line noise of the image by adjusting Phase and Clock separately The adjusting range is from 0 to 100 Only available for VGA input i 4 Phase adjusts the phase of the pixel clock signal With a wrong phase Lo adjustment the screen shows horizontal disturbances Clock pixel frequency controls the number of pixels scanned by one horizontal sweep If the frequency is not correct the screen shows vertical stripes and the image is not proportional ASUS LCD Monitor VN248 Series 3 3 3 4 4 5 Input Select Select the input source from VGA HDMI MHL 1 or HDMI MHL 2 input signal B splendid VGA gt amp Color HDMI MHL 1 gt Image HDMI MHL 2 gt xX System Setup Move Menu s Exit System Setup Adjusts the system configuration ASUS VN248 Splendid Splendid Demo Mode OFF gt amp Color Volume 50 gt mi ECO Mode OFF p mage a OSD Setup gt Input Select Language English gt Information gt All2. PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN NO EVENT SHALL ASUS ITS DIRECTORS OFFICERS EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING DAMAGES FOR LOSS OF PROFITS LOSS OF BUSINESS LOSS OF USE OR DATA INTERRUPTION OF BUSINESS AND THE LIKE EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions This device may not cause harmful interference and This device must accept any interfere
3. are not user configurable 2 Color Select the image color you like from this function ASUS VN248 B Splendid Brightness 100 gt Image Input Select Color Temp User Mode gt X System Setup Move F Menu s Exit Brightness The adjusting range is from 0 to 100 The lt button is also a hotkey to activate this function e Contrast The adjusting range is from 0 to 100 e Saturation The adjusting range is from 0 to 100 e Color Temp Contains three preset color modes Cool Normal Warm and one User Mode e Skin Tone Contains three color modes including Reddish Natural and Yellowish i 4 Inthe User Mode colors of R Red G Green and B Blue are user L configurable the adjusting range is from 0 100 Chapter 3 General Instruction 3 Image You can adjust the image Sharpness Trace Free Aspect Control ASCR Position VGA only and Focus VGA only from this main function ASUS VN248 amp Splendid amp Color Trace Free 60 gt a Aspect Control Full gt Vividpixel 25 gt Input Select F System Set X ys emu Position gt Focus gt Move Menu s Exit e Sharpness Adjusts the picture sharpness The adjusting range is from 0 to 100 e Trace Free Speeds up the response time by Over Drive technology The adjusting range is from lower 0 to faster 100 e Aspect Control Adjusts the aspect ratio to Full 4 3
4. Reset gt 2 s v Move E Menu s Exit Splendid Demo Mode Activate the demo mode for the Splendid function Volume Adjust the earphone or speaker output volume level The adjusting range is from 0 to 100 ECO Mode Activate the ecology mode for power saving OSD Setup Adjusts the horizontal postition H Position vertical position V Position OSD Timeout DDC CI and Transparency of the OSD screen Language Select OSD language The selections are English French German Spanish Italian Dutch Russian Traditional Chinese Simplified Chinese Japanese Persian Thai Indonesian Poland Turkey Portugal Czech Croatia Hungary Romania and Korean Key Lock To disable all function keys Press the MENU button over five seconds to cancel the key lock function Information Displays the monitor information All Reset Selects Yes to revert all settings to the factory default mode Chapter 3 General Instruction 3 2 Specifications Model Panel Size Max Resolution Brightness Typ Intrisinc Contrast Ratio Typ Viewing Angle CR lt 10 Display Colors Response Time Typ DVI input D Sub input HDMI input Power ON Consumption Speaker Earphone Power saving mode Power off mode Tilt VESA Wall Mounting Phys Dimension WxHxD Box Dimension WxHxD Net Weight Esti Gross Weight Esti Voltage Rating 5 ms Gray to Gray i H es es es es Ye Ye 35 W Specifications are subj
5. SUS LCD monitor The latest widescreen LCD monitor from ASUS provides a crisper broader and brighter display plus a host of features that enhance your viewing experience With these features you can enjoy the convenience and delightful visual experience that the monitor brings you 1 2 Package contents Check your package for the following items LCD Monitor Monitor Base Quick Start Guide Warranty Card 1x Power Cord 1x VGA Cable 1x Audio Cable 1x HDMI Cable option 1x HDMI to DVI cable option LK RRA RAS 1x MHL Cable option AN If any of the above items is damaged or missing contact your retailer immediately ASUS LCD Monitor VN248 Series 1 1 1 2 1 3 Assembling the monitor base 1 Attach the base to the arm 2 Beware to align the latch to the notch on the base 3 The end of the arm will slightly protrude from the base No need to push it in 4 Screw the base to the arm tightly V We recommend that you cover the table surface with soft cloth to prevent Ce damage to the monitor 1 4 Connect cables Connect the cables you need based on chapter 1 5 2 page 1 5 Flip upward the IO port cover to connect cables After connected cables L replace the cover and carefully push it upward to its original position with both thumbs at both sides of the cover Chapter 1 Product Introduction 15 Monitor introduction 1 5 1 Front of
6. ay become wet Place the monitor on a stable surface Unplug the unit during a lightning storm or if it will not be used for a long period of time This will protect the monitor from damage due to power surges Never push objects or spill liquid of any kind into the slots on the monitor cabinet To ensure satisfactory operation use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 240V AC The socket outlet shall be installed near the equipment and shall be easily accessible If you encounter technical problems with the monitor contact a qualified service technician or your retailer Care amp Cleaning Before you lift or reposition your monitor it is better to disconnect the cables and power cord Follow the correct lifting techniques when positioning the monitor When lifting or carrying the monitor grasp the edges of the monitor Do not lift the display by the stand or the cord Cleaning Turn your monitor off and unplug the power cord Clean the monitor surface with a lint free non abrasive cloth Stubborn stains may be removed with a cloth dampened with mild cleaner Avoid using a cleaner containing alcohol or acetone Use a cleaner intended for use with the LCD Never spray cleaner directly on the screen as it may drip inside the monitor and cause an electric shock The following symptoms are normal with the monitor The screen may flicker during the init
7. ect to change without notice ASUS LCD Monitor VN248 Series 3 5 3 6 3 3 Troubleshooting FAQ Problem Power LED is not ON The power LED lights amber and there is no screen image Screen image is too light or dark Screen image is not centered or sized properly Possible Solution Press the button to check if the monitor is in the ON mode e Check if the power cord is properly connected to the monitor and the power outlet Check if the monitor and the computer are in the ON mode Make sure the signal cable is properly connected the monitor and the computer Inspect the signal cable and make sure none of the pins are bent Connect the computer with another available monitor to check if the computer is properly working Adjust the Contrast and Brightness settings via OSD Press the button for two seconds to automatically adjust the image e Adjust the H Position or V Position settings via OSD Screen image bounces or a wave Make sure the signal cable is properly connected to pattern is present in the image Screen image has color defects white does not look white Screen image is blurry or fuzzy No sound or sond is low the monitor and the computer Move electrical devices that may cause electrical interference Inspect the signal cable and make sure that none of the pins are bent e Perform Reset via OSD Adjust the R G B color settings or select the Color Tem
8. ia BE VN248 Series LCD Monitor User Guide Table of contents NOTICRS nid danai e a aia raaa iii Safety information iv Care amp Cleaning sine v 1 1 Welcome sieren aieiaa 1 1 1 2 Package contents ss 1 1 1 3 Assembling the monitor base 1 2 1 4 Connect cables sise 1 5 Monitor introduction 1 5 1 Front of the LCD monitor 1 3 1 5 2 Rear of the LCD monitor 1 5 1 5 3 QUICKFit Function 1 6 2 1 Detaching the arm stand for VESA wall mount 2 1 2 2 Adjusting the monitor 3 1 OSD On Screen Display menu 3 1 1 How to reconfigure snini 3 1 2 OSD Function Introduction 3 2 Specifications resa aa aae aaua uen enaa aaa in rome reed 3 3 Troubleshooting FAQ 3 4 Supported Timing List Copyright 2013 ASUSTeK COMPUTER INC All Rights Reserved No part of this manual including the products and software described in it may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form or by any means except documentation kept by the purchaser for backup purposes without the express written permission of ASUSTeK COMPUTER INC ASUS Product warranty or service will not be extended if 1 the product is repaired modified or altered unless such repair modification of alteration is authorized in writing by ASUS or 2 the serial number of the product is defaced or missing ASUS
9. ial use due to the nature of the fluorescent light Turn off the Power Switch and turn it on again to make sure that the flicker disappears You may find slightly uneven brightness on the screen depending on the desktop pattern you use When the same image is displayed for hours an afterimage of the previous screen may remain after switching the image The screen will recover slowly or you can turn off the Power Switch for hours When the screen becomes black or flashes or cannot work anymore contact your dealer or service center to fix it Do not repair the screen by yourself Conventions used in this guide N WARNING Information to prevent injury to yourself when trying to l complete a task S A CAUTION Information to prevent damage to the components when trying to complete a task IMPORTANT Information that you MUST follow to complete a task NOTE Tips and additional information to aid in completing a task NIC vi Where to find more information Refer to the following sources for additional information and for product and software updates 1 ASUS websites The ASUS websites worldwide provide updated information on ASUS hardware and software products Refer to http www asus com 2 Optional documentation Your product package may include optional documentation that may have been added by your dealer These documents are not part of the standard package 1 1 Welcome Thank you for purchasing the A
10. m the stand 3 Or you may directly use a screwdriver to remove the screws that secure the stand to the monitor and detach the stand from the monitor AN We recommend that you cover the table surface with soft cloth to prevent damage to the monitor Hold the stand while removing the screws The VESA wall mount kit 100 x 100 mm is purchased separately ses Use only the UL Listed Wall Mount Bracket with minimum weight load 22 7kg Screw size M4 x 10 mm ASUS LCD Monitor VN248 Series 2 2 2 2 Adjusting the monitor For optimal viewing we recommend that you look at the full face of the monitor then adjust the monitor to the angle that is most comfortable for you Hold the stand to prevent the monitor from falling while changing its angle You can adjust the monitor s angle from 5 to 20 5 20 Chapter 2 Setup OSD On Screen Display menu 3 1 1 How to reconfigure ASUS VN248 amp Color Standard Mode gt Image Theater Mode X System Setup Night View Mode sRGB gt Move Menu s Exit Press the MENU button to activate the OSD menu Press W and A to navigate through the functions Highlight and activate the desired function by pressing the MENU button If the function selected has a sub menu press W and A again to navigate through the sub menu functions Highlight and activate the desired sub menu function by pressing the MENU butto
11. n Press W and A to change the settings of the selected function To exit the OSD menu press the A ES button Repeat step 2 and step 3 to adjust any other function 3 1 2 OSD Function Introduction Splendid This function contains six sub functions that you can select for your preference Each mode has the Reset selection allowing you to maintain your setting or return to the preset mode ASUS VN248 amp Color Standard Mode gt Image Theater Mode X System Setup Night View Mode sRGB gt Move E Menu s Exit e Scenery Mode This is the best choice for scenery photo displaying with SPLENDID Video Intelligence Technology ASUS LCD Monitor VN248 Series 3 1 e Standard Mode This is the best choice for document editing with SPLENDID Video Intelligence Technology e Theater Mode This is the best choice for movie watching with SPLENDID Video Intelligence Technology e Game Mode This is the best choice for game playing with SPLENDID Video Intelligence Technology e Night View Mode This is the best choice for playing dark scene game or watching dark scene movie with SPLENDID Video Intelligence Technology e sRGB Mode This is the best choice for viewing photos and graphics from PCs i 4 Inthe Standard Mode the Saturation SkinTone Sharpness and ASCR om functions are not user configurable In the sRGB the Saturation Color Temp SkinTone Sharpness Brightness Contrast and ASCR functions
12. nce received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with manufacturer s instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment to an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help coma As an Energy Star Partner our company has determined that this product meets the Energy Star guidelines for energy Curie efficiency ENERGY STAR Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital appara
13. perature via OSD Press the button for two seconds to automatically adjust the image for VGA mode only Adjust the Phase and Clock settings via OSD Make sure the audio cable is properly connected to the monitor Adjust the volume settings of both your monitor and computer Make sure the computer sound card driver is properly installed and activated Chapter 3 General Instruction 3 4 Supported Timing List VESA IBM Modes Support Timing Resolution Refresh Rate Horizontal Frequency HDMI 1 3 CEA 861 Formats Supported Timing Resolution Refresh Rate Horizontal Frequency 1440 x 576P 31 25KHz 1280 x 720P 59 94 60Hz 44 955 45KHz 1920 x 1080i 28 125KHz 1440 x 480P 59 94 GOHZ 31 469 31 5KHz The modes not listed in the above tables may not be supported For optimal resolution we recommend that you choose a mode listed in the above tables ASUS LCD Monitor VN248 Series
14. the LCD monitor MENU 1 QuickFit Button e Thisis a hotkey to activate the QuickFit function designed for alignment e The QuickFit function contains 7 pages of common grid patterns paper sizes and photo sizes See page 1 6 for details 2 B B Button e Automatically adjust the image to its optimized position clock and phase by long pressing this button for 2 4 seconds for VGA mode only e Use this hotkey to switch from six video preset modes Scenery Standard Theater Game Night View and sRGB Mode with SPLENDID Video Intelligence Technology Exitthe OSD menu or go back to the previous menu as the OSD menu is active 3 lt Y Button e Press this button to decrease the value of the function selected or move to the next function e This is also a hotkey for Volume adjustment ASUS LCD Monitor VN248 Series 1 3 1 4 MENU Button e Press this button to enter the OSD menu e Press this button to enter select the icon function highlighted while the OSD is activated e Press this button over five seconds to enable or disable the key lock function t A Button e Press this button to increase the value of the function selected or move to the previous functions e This is also a hotkey for Brightness adjustment 5 Input Select Button e Use this hotkey to switch from VGA HDMI MHL 1 or HDMI MHL 2 input signal O Power Button Power Indicator e Press this button to
15. turn the monitor on off e The color definition of the power indicator is as the below table Description ON Standby mode OFF Chapter 1 Product Introduction 1 5 2 Rear of the LCD monitor 1 AC IN port HDMI MHL port VGA port Audio in Port Earphone out Port Kensington Lock Screw Holes for VESA Wall Mount Control buttons DO NAAR WON ASUS LCD Monitor VN248 Series 1 5 1 6 1 5 3 QuickFit Function The QuickFit function contains three patterns 1 Grid 2 Paper size 3 Photo size 1 Grid pattern Facilitates designers and users to organize content and layout on one page and achieve a consistent look and feel Alignment Grid 2 Paper size Provides users to view their documents in real size on the screen Pitter Ef 3 Photo size Provides photographers and other users to accurately view and edit their photos in real size on the screen Dx2 8x10 Chapter 1 Product Introduction 2 1 Detaching the arm stand for VESA wall mount The detachable stand of this monitor is specially designed for VESA wall mount 1 Disconnect power and signal cables Carefully put the front of the monitor face down on a clean table 2 Use your fingers to loosen the screw located at the bottom of the base and remove the base fro
16. tus set out in the Radio Interference Regulations of the Canadian Department of Communications This class B digital apparatus complies with Canadian ICES 003 Safety information Before setting up the monitor carefully read all the documentation that came with the package To prevent fire or shock hazard never expose the monitor to rain or moisture Never try to open the monitor cabinet The dangerous high voltages inside the monitor may result in serious physical injury If the power supply is broken do not try to fix it by yourself Contact a qualified service technician or your retailer Before using the product make sure all cables are correctly connected and the power cables are not damaged If you detect any damage contact your dealer immediately Slots and openings on the back or top of the cabinet are provided for ventilation Do not block these slots Never place this product near or over a radiator or heat source unless proper ventilation is provided The monitor should be operated only from the type of power source indicated on the label If you are not sure of the type of power supply to your home consult your dealer or local power company Use the appropriate power plug which complies with your local power standard Do not overload power strips and extension cords Overloading can result in fire or electric shock Avoid dust humidity and temperature extremes Do not place the monitor in any area where it m
Download Pdf Manuals
Related Search