ASRock IMB-130 Series Owner's Manual
Contents
1. IMB 130 motherboard provides two 204 pin DDR3 Double Data Rate 3 SO DIMM slots 1 It is not allowed to install a DDR or DDR2 memory module into a DDRS3 slot otherwise this motherboard and SO DIMM may be damaged 2 Please install the memory module from DDR3 A2 slot for the first priority Installing a SO DIMM Please make sure to disconnect the power supply before adding or removing SO DIMMs or the system components Step 1 Unlock a SO DIMM slot by pressing the retaining clips outward Step 2 Align a SO DIMM on the slot such that the notch on the SO DIMM matches the break on the slot Rill 1GB 1333 Y3128M8 EDJ1D wann noth daba E The SO DIMM only fits in one correct orientation It will cause perma nent damage to the motherboard and the SO DIMM if you force the SO DIMM into the slot in the incorrect orientation Step 3 Firmly insert the SO DIMM into the slot until the retaining clips at both ends fully snap back in place and the SO DIMM is properly seated 12 2 4 Expansion Slots PCI and mini PCIE Slots There is 1 PCI slot and 1 mini PCIE slot on this motherboard PCI slot The PCI slot is used to install an expansion card that has 32 bit PCI interface The mini PCIE slot is used for PCI Express mini cards Installing an expansion card Step 1 Before installing the expansion card please make sure that the power supply is switched off or the power cord is unplugged Please read the documentati2. a new programming interface for SATA host controllers developed through a joint industry effort NOTE What is Hot Plug Function If the SATA SATA2 HDDs are NOT set for RAID configuration it is called Hot Plug for the action to insert and remove the SATA SATA2 HDDs while the system is still power on and in working condition However please note that it cannot perform Hot Plug if the OS has been installed into the SATA SATA2 HDD 21 2 9 Driver Installation Guide To install the drivers to your system please insert the support CD to your optical drive first Then the drivers compatible to your system can be auto detected and listed on the support CD driver page Please follow the order from top to bottom to install those required drivers Therefore the drivers you install can work properly 22 Chapter 3 UEFI SETUP UTILITY 3 1 Introduction This section explains how to use the UEFI SETUP UTILITY to configure your system The UEFI chip on the motherboard stores the UEFI SETUP UTILITY You may run the UEFI SETUP UTILITY when you start up the computer Please press F2 or Del during the Power On Self Test POST to enter the UEFI SETUP UTILITY otherwise POST will continue with its test routines If you wish to enter the UEFI SETUP UTILITY after POST restart the system by pressing lt Ctl gt lt Alt gt Delete or by pressing the reset button on the system chassis You may also restart by turning the syste
3. GND motherboard OOOO 4 PWR 6 6 GND PLED Header p This header accommodates LED PWRBIN several system front panel functions Connect the power switch reset switch and system status indicator on the chassis to this header according to the pin assignments below Note the positive and negative pins before connecting the cables PWRBTN Power Switch Connect to the power switch on the chassis front panel You may configure the way to turn off your system using the power switch RESET Reset Switch Connect to the reset switch on the chassis front panel Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart 17 Speaker Connector 4 pin SPEAKER 1 see p 8 No 28 Front Panel Audio Header 9 pin HD AUDIO1 see p 8 No 29 A PLED System Power LED Connect to the power status indicator on the chassis front panel The LED is on when the system is operating The LED keeps blinking when the sys tem is in S1 sleep state The LED is off when the system is in S3 S4 sleep state or powered off S5 HDLED Hard Drive Activity LED Connect to the hard drive activity LED on the chassis front panel The LED is on when the hard drive is reading or writing data The front panel design may differ by chassis A front panel module mainly consists of power switch reset switch power LED hard drive activity LED speaker and etc When connecting your
4. ISRock IMB 130 User Manual Version 1 0 Published March 2013 Copyright92013 ASRock INC All rights reserved Copyright Notice No part of this manual may be reproduced transcribed transmitted or translated in any language in any form or by any means except duplication of documentation by the purchaser for backup purpose without written consent of ASRock Inc Products and corporate names appearing in this manual may or may not be regis tered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe Disclaimer Specifications and information contained in this manual are furnished for informa tional use only and subject to change without notice and should not be constructed as a commitment by ASRock ASRock assumes no responsibility for any errors or omissions that may appear in this manual With respect to the contents of this manual ASRock does not provide warranty of any kind either expressed or implied including but not limited to the implied warran ties or conditions of merchantability or fitness for a particular purpose In no event shall ASRock its directors officers employees or agents be liable for any indirect special incidental or consequential damages including damages for loss of profits loss of business loss of data interruption of business and the like even if ASRock has been advised of the possi
5. No 1 HEADER 2X5P MO 10 pin SET CM4 see p 8 No 25 1 3 12V 10 pin SET CM5 3 5 5V see p 8 No 24 7 9 COM port signal Data Carrier Detect 2 4 12V 10 pin SET CM6 4 6 45V See Pe NOs 25 8 10 COM port signal Ring Indicator Panel Power Selection 6068 1 2 3V 3 pin PNL_PWR1 T 23 2 3 5V see p 8 No 3 Backlight Power Selection OO 1 2 5V 3 pin BKT PWR1 T 23 2 3 12V see p 8 No 4 15 ATX AT Mode Selection 3 pin PWR_JP1 see p 8 No 18 eg bo Digital Input Output Power Selection 3 pin JGPIO_PWR1 see p 8 No 16 IO NIO y 16 2 3 1 2 2 3 AT Mode ATX Mode 12V 5V 2 6 Onboard Headers and Connectors A Onboard headers and connectors are NOT jumpers Do NOT place jumper caps over these headers and connectors Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard SATA2 Connectors ad These two Serial ATA2 SATA2_1 see p 8 No 10 L usd SATA2 connectors support SATA2 2 see p 8 No 11 Kal SATA data cables for internal SATA2 1 SATA2 2 storage devices The current USB 2 0 Ports 4 pin USB4 5 see p 8 No 13 4 pin USB6 see p 8 No 14 System Panel 9 pin PANEL1 see p 8 No 19 A SATA2 interface allows up to 3 0 Gb s data transfer rate PWR 4 4 GND Besides four default USB 2 0 ports on the I O panel there are three USB 2 0 ports on this PWR 5 5
6. Please be noted that the password date time user default profile and MAC address will be cleared only if the CMOS battery is removed Panel Resolution Selection Reserved 12 pin JLVD_GPIO1 Default set by BIOS GPIog High GPIOx 1 GPIO Low GPIOx 0 see p 8 No 5 Note If you want to use BIOS to set Panel type then set all GPIO 3 0 1111 If you want to use jumpers to set Panel type select Set by Jumper in BIOS 14 E 1366 6 Single LED LUE CCTUI oe O CIE OR UE ci t lov Tozexrenze oii ccorL 1020 788 8 Sing com Ye om Tasoxtoadaenazanicort zm 1020 8 bw com vs oo resexreenesivrcncort 1308 708 8 Sige cct Ye oror Taamsnozeewzwcor 1440 wo s btw com Ye ova weeecoeewrem 1024 eo s sme t w om sapeooneezemten 1 wo s bw 100 we oss KEE 1200 1020 s bw tb Nw gt foot sozewresize cromo 1020 708 s ome ib Ne How teoo so0re iz lt neD 1600 9m s bwr i om KEIER res 8 Single tb n moo 1szocosozesiz meo 1920 we s twr tb Nw Tor swwenozeserewtED e so s Single ib w mo erosoan omeo oao 490 8 sme tb mo ENEE 1200 e0 e Sige 0 Nw COM Port PWR Setting Headers 10 pin SET_CM1 see p 8 No 30 1210 H2NVIO L SET COMI Leen 10 pin SET CM2 see p 8
7. To jump to the Exit Screen or exit the current screen 3 2 Main Screen When you enter the UEFI SETUP UTILITY the Main screen will appear and display the system overview Aptio Setup Utility Copyright C 20 American Me System Language English 24 3 3 Advanced Screen In this section you may set the configurations for the following items CPU Configu ration Chipset Configuration Storage Configuration Super IO Configuration ACPI Configuration USB Configuration and Voltage Configuration Aptio Setup Utility Copyright C 20 American Megatrent gt CPU Configuration Setting wrong values in this section may cause the system to malfunction Instant Flash Instant Flash is a UEFI flash utility embedded in Flash ROM This conve nient UEFI update tool allows you to update system UEFI without entering operating systems first like MS DOS or Windows Just launch this tool and save the new UEFI file to your USB flash drive floppy disk or hard drive then you can update your UEFI only in a few clicks without prepar ing an additional floppy diskette or other complicated flash utility Please be noted that the USB flash drive or hard drive must use FAT32 16 12 file system If you execute Instant Flash utility the utility will show the UEFI files and their respective information Select the proper UEFI file to update your UEFI and reboot your system after UEFI update process completes 25 3 3 1 CPU Configuration Apt
8. for USB devices There are four configuration options Enabled Auto Disabled and UEFI Setup Only The default value is Enabled Please refer to below descriptions for the details of these four options Enabled Enables support for legacy USB Auto Enables legacy support if USB devices are connected Disabled USB devices are not allowed to use under legacy OS and UEFI setup when Disabled is selected If you have USB compatibility is sue it is recommended to select Disabled to enter OS UEFI Setup Only USB devices are allowed to use only under UEFI setup and Windows Linux OS USB Mouse Wheel Support Use this option to enable or disable USB Mouse Wheel Support The default value is Disabled 31 3 3 7 Voltage Configuration 2011 Ameri Aptio Setup Utility Copyrigh DRAM Voltage DRAM Voltage Use this to select DRAM Voltage The default value is Auto 32 3 4 Hardware Health Event Monitoring Screen In this section it allows you to monitor the status of the hardware on your system including the parameters of the CPU temperature motherboard temperature CPU fan speed chassis fan speed and the critical voltage Aptio Setup Utility Copyright C 20 American Megatrend CPU_ZFAN1 Setting Full On CPU FAN Setting This allows you to set CPU FAN1 s speed Configuration options Full On and Automatic Mode The default value is Full On CHA FAN Setting This allows you to set CHA
9. recovers Onboard HD Audio Select Auto Enabled or Disabled for the onboard HD Audio feature If you select Auto the onboard HD Audio will be disabled when PCI Sound Card is plugged Front Panel Select Auto or Disabled for the onboard HD Audio Front Panel Onboard LAN This allows you to enable or disable the Onboard LAN feature 27 3 3 3 Storage Configuratio Aptio Setup Utility Copyright C 2011 American Megatrends Inc Onboard SATAII Mode Onboard SATAII Mode Use this to select SATA2 mode Configuration options IDE Mode AHCI Mode and Disabled The default value is IDE Mode AHCI Advanced Host Controller Interface supports NCQ and other new features that will improve SATA disk perfor mance but IDE mode does not have these advantages Hard Disk S M A R T Use this item to enable or disable the S M A R T Self Monitoring Analy sis and Reporting Technology feature Configuration options Disabled and Enabled 28 3 3 4 Super IO Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc gt COM1 Configuration COMA1 Configuration Use this to set parameters of COM1 COM2 Configuration Use this to set parameters of COM2 COM4 Configuration Use this to set parameters of COM4 COM5 Configuration Use this to set parameters of COM5 COM6 Configuration Use this to set parameters of COM6 LPT1 Port Configuration Use this set parameters of the onb
10. the motherboard sup ports Click on a specific item then follow the installation wizard to install it 4 2 4 Contact Information If you need to contact ASRock or want to know more about ASRock you re welcome to visit ASRock s website at http www asrock com or you may con tact your dealer for further information 37
11. 4 pin CPU_FAN1 cable to the connector and see p 8 No 7 do t match the black wire to the CPU_FAN_SPEED FAN_SPEED_CONTROL ground pin CPU fan still can work successfully even without the fan speed control function If you plan to connect the 3 Pin CPU fan to the CPU fan connector on this motherboard please connect it to Pin 1 3 Though this motherboard provides 4 Pin CPU fan Quiet Fan support the 3 Pin Pin 1 3 Connected lt u ern 3 Pin Fan Installation ia DC 12V Power Connector Please connect a DC 12V 4 pin DC12V1 12V TI 12V power supply to this connector see p 8 No 6 elt Tee COM Port Header 10 pin COM4 see p 8 No 22 ANO S S dMd ANO Fr vY AMd 10 pin COM5 see p 8 No 21 10 pin COMO see p 8 No 20 RS232 RS422 RS485 1 ee TX RTX carrier detect 2 RXD Receive RX N A data TXD Transmit DG RTX data 4 E RX N A terminal ready 19 Printer Port Header 25 pin LPT1 see p 8 No 12 LVDS Con mes 40 pin LVDS1 40 Signal Name VDD PWR EDID CLK 39 ERMEE Pin amp ME 6 8 O 40 see p 8 No 2 1 ES Sil HB EHE S EB Bitch BS Bs BS GNb B4 BE doo pE 8 x E RXINEO RXINEO d RXINE1 RXINEL RXINE2 RXINE2 RXINE3 RXINES RXECLKIN RXECLKIN BackLight EN Backlight PWR Output Power 1 1 5V o 4 pin SATA_PWR1 Zi 2 3 GND 2 5 see p 8 N
12. FAN1 s speed Configuration options Full On and Automatic Mode The default value is Full On 33 3 5 Boot Screen In this section it will display the available devices on your system for you to config ure the boot settings and the boot priority Aptio Setup Utility Copyright C 2011 American Megatrends Inc Boot Option 1 SATA PM ST380817 Setup Prompt Timeout This shows the number of seconds to wait for setup activation key 65535 OXFFFF means indefinite waiting Bootup Num Lock If this item is set to On it will automatically activate the Numeric Lock function after boot up Boot From Onboard LAN Use this item to enable or disable the Boot From Onboard LAN feature 34 3 6 Security Screen In this section you may set change or clear the supervisor user password for the system Aptio Setup Utility Copyright C 2011 American Megatrends Inc Supervisor Password 35 3 7 Exit Screen Aptio Setup Utility Copyright C 20 Amer an Megatrent Save Changes and Exit Save Changes and Exit When you select this option it will pop out the following message Save configuration changes and exit setup Select OK to save the changes and exit the UEFI SETUP UTILITY Discard Changes and Exit When you select this option it will pop out the following message Discard changes and exit setup Select OK to exit the UEFI SETUP UTILITY without saving any changes Discard Changes When y
13. ITX form factor 6 7 x 6 7 17 0 x 17 0 cm motherboard Before you install the motherboard study the configuration of your chassis to ensure that the motherboard fits into it motherboard Failure to do so may cause physical injuries to you and damages to motherboard components y Make sure to unplug the power cord before installing or removing the 2 1 Screw Holes Place screws into the holes to secure the motherboard to the chassis IN Do not over tighten the screws Doing so may damage the motherboard 2 2 Pre installation Precautions Take note of the following precautions before you install motherboard components or change any motherboard settings 1 Unplug the power cord from the wall socket before touching any component 2 To avoid damaging the motherboard components due to static electricity NEVER place your motherboard directly on the carpet or the like Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components 3 Hold components by the edges and do not touch the ICs 4 Whenever you uninstall any component place it on a grounded antistatic pad or in the bag that comes with the component switched off or the power cord is detached from the power supply Before you install or remove any component ensure that the power is Failure to do so may cause severe damage to the motherboard peripherals and or components 11 2 3 Installation of Memory Modules SO DIMM
14. SB 2 0 compliant VDS 25 Inverter MER gem e Serial 3 RS 232 SATA 2 x SATA2 3 0Gb s Internal m Parallel onnector pU mSATA 0 IDA 0 Watchdog Timer Input PWR 12V DC In 4 pin ATX PWR Con AT ATX Supported AT Directly PWR on as power input ready ATX Press button to PWR on after power input ready Environment 0 C 60 C Power Requirements 1 3 Motherboard Layout 30 Ps2 Keyboard 345 6 DC12V1 CPU FAN1 DDR3 A1 DDR3 A2 Designed in Taipei CHA FAN1 a Oo 2 OO ajoo E joo lon COM COM LVDS1 Port B PortA _ foo a OO Aloo E OO Ooh o VGA1 PHY Top RJ 45 PHY AUDIO e a 2 2 SPEAKER1 1 ASRock 29 28 CMOS Battery 00000 B0000 SET_CM4 00000 gt noooo SET_CM5 00000 0000 BLT_PWR2 1 onl SS 3 les BLT_VOL1 66 o o DOoo0on nooooo 140000000 po 1 incen RESET P S l pr JP GEI JGPIO_PWR1 EEE EEE DELI 27 SATA_PWR1 j PNL_PWR1 eer Pei SET_CM6 00000 00000 OMS 00000 00000 f COM6 PLED PWRBTN DEER 0000 Lo JGP 101 26 25242322212019 18 17 16 10 11 12 13 14 15 O ON OO c P O N a 0 MM MM MM MM MM 2 a a a 2 2 ch ch 3 O O ON OO P Go MM A OO AN Oa P Go M O COM Port PWR Setting header COM Port2 LVDS Con Panel VDD PWR Setting Panel BackLight PWR Setting Panel resolution selection control 4 Pin AT
15. TUP UTILITY eerte one 3 1 3 2 3 3 3 4 3 5 3 6 3 7 MOGUC HOM P P o a Ei OT UEFI Ieper peritus 3 1 2 Navigation KEYS EE Main e E Na E 3 9 1 CPU ee ere E 3 3 2 ne de ue E e DE 3 9 0 Storage COMMQUIATION WE 3 3 4 Super IO ee ue TT 9 9 9 ACPI ConfIQuESEtIOI icso ioter torn eege 326 ER en e DE e E 3 3 7 Voltage CONTQUIAUION E Hardware Health Event Monitoring Screen 0 000 Boot SGI E SCU SOSA RI c meer m 4 Software Support 37 4 1 Install Operating Gvstem eneee 37 4 2 Support CD Information oocccccccoccncncccnnncnconnncnnnanos 37 4 2 1 Running SUDDOTPL C RE 37 4 2 2 Drivers Men 37 4 2 3 Utilities Mod oa 37 4 2 4 Contact Ioiormaton 37 Chapter 1 Introduction Thank you for purchasing ASRock IMB 130 motherboard a reliable motherboard produced under ASRock s consistently stringent quality control It delivers excellent performance with robust design conforming to ASRock s commitment to quality and endurance In this manual chapter 1 and 2 contain introduction of the motherboard and step by step guide to the hardware installation Chapter 3 and 4 contain the configuration guide to BIOS setup and information of the Support CD Because the motherboard specifications and the BIOS software might be updated the content of this manual will be subject to change without no tice In case any modifications of this manual occ
16. X PWR In 12V 4 Pin FAN con 12V 3 Pin FAN con 12V Output Power SATA2 Connector SATA2 1 SATA2 Connector SATA2 2 Printer Port Header Internal USB connectors USB Port4 5 Internal USB connector USB Port6 Digital UO Header Digital UO Header PWR setting Clear CMOS Header PWR On mode setting System Panel Control Header White Internal COM port connector COM Port6 Internal COM port connector COM Port5 Internal COM port connector COM Port4 COM Port PWR Setting header COM Port6 COM Port PWR Setting header COM Port5 COM Port PWR Setting header COM Port4 Panel Brightness and Speaker Volume Control Panel BackLight Inverter connector Speaker connector Front Panel Audio Header White COM Port PWR Setting header COM Port1 1 4 I O Panel A al _ Os Pl SCH eo 11 10 9 8 T PS 2 Mouse Port 7 USB2 0 Ports USB23 Com Port A COM1 8 USB2 0 Ports USB01 VGA Port VGA1 9 HDMI Port HDMI1 LAN RJ 45 Port 10 Com Port B COM2 Line out Green 11 PS 2 Keyboard Port Microphone Pink There are two LED next to the LAN port Please refer to the table below for the LAN port LED indications B Data Activity LAN Port LED Indications ACT LINK SPEED Activity Link LED SPEED LED LED LED Description 10Mbps connection 100Mbps connection 1Gbps connection LAN Port 10 Chapter 2 Installation This is a Mini
17. bility of such damages arising from any defect or error in the manual or product Fe This device complies with Part 15 of the FCC Rules Operation is subject to the fol lowing two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CALIFORNIA USA ONLY The Lithium battery adopted on this motherboard contains Perchlorate a toxic substance controlled in Perchlorate Best Management Practices BMP regulations passed by the California Legislature When you discard the Lithium battery in Cali fornia USA please follow the related regulations in advance Perchlorate Material special handling may apply see www dtsc ca gov hazardouswaste perchlorate ASRock Website http www asrock com Contents 1 Introduction eren nnn 1 1 1 2 1 3 1 4 Package Contents secs ardid Pecado Motherboard Layout o een 2 Installation KEEN NEEN NENNEN ENEE 2 1 2 2 2 3 2 4 2 9 2 6 27 2 8 2 9 SEW HOIS asocia Pre installation Precautions sseessss Installation of Memory Modules SO DIMM Expansion Slots PCI and mini PCIE Slots JUMPErS SO lion Onboard Headers and Connechors Serial ATA SATA Serial ATA2 SATA2 Hard Disks WS Eeer EE Hot Plug and Hot Swap Functions for SATA SATA2 3 UEFI SE
18. chassis front panel module to this header make sure the wire assignments and the pin assign ments are matched correctly 1 Speaker R 2 Speaker R 3 Speaker L R L 4 Speaker L This is an interface for front OUT_RET OUT2 L panel audio cable that allows J_SENSE OUT2 R MIC2 R MIC2 L MIC_RET convenient connection and PRESENCE control of audio devices GND 1 High Definition Audio supports Jack Sensing but the panel wire on the chassis must support HDA to function correctly Please follow the instruction in our manual and chassis manual to install your system 2 If you use AC 97 audio panel please install it to the front panel audio header as below A Connect Mic IN MIC to MIC2 L B Connect Audio R RIN to OUT2 R and Audio L LIN to OUT2 L C Connect Ground GND to Ground GND D MIC RET and OUT RET are for HD audio panel only You don t need to connect them for AC 97 audio panel E To activate the front mic For Windows XP XP 64 bit OS Select Mixer Select Recorder Then click FrontMic For Windows 7 7 64 bit Vista Vista 64 bit OS Go to the FrontMic Tab in the Realtek Control panel Adjust Recording Volume 18 Chassis Fan Connector Please connect the fan cable 3 pin CHA FAN1 FAN SPEED i to the fan connector and 12V see p 8 No 8 GND match the black wire to the ground pin CPU Fan Connector ATF Please connect the CPU fan
19. io Setup Utility Copyright C 20 No Execute Memory Protection Disabled Intel Hyper Threading Technology To enable this feature it requires a computer system with an Intel proces sor that supports Hyper Threading technology and an operating system that includes optimization for this technology such as Microsoft Windows 7 Set to Enabled if using Microsoft Windows 7 No Excute Memory Protection No Execution NX Memory Protection Technology is an enhancement to the IA 32 Intel Architecture An IA 32 processor with No Execute NX Memory Protection can prevent data pages from being used by malicious software to execute code 26 3 3 2 Chipset Configuration Aptio Setup Utility Copyright C 20 American Megatrends nc Set Panel Type by UEFI Setup Set Panel Type by Use this to configure Set Panel Type The default value is UEFI Setup Panel Type Selection Use this to select panel type The default value is 1366x768 18 bit 1 ch LED ACPI HPET Table Use this item to enable or disable ACPI HPET Table The default value is Enabled Please set this option to Enabled if you plan to use this moth erboard to submit Windows certification Restore on AC Power Loss This allows you to set the power state after an unexpected AC power loss If Power Off is selected the AC power remains off when the power recovers If Power On is selected the AC power resumes and the system starts to boot up when the power
20. m off and then back on Because the UEFI software is constantly being updated the following UEFI setup screens and descriptions are for reference purpose only and they may not exactly match what you see on your screen 3 1 1 UEFI Menu Bar The top of the screen has a menu bar with the following selections Main To set up the system time date information OC Tweaker To set up overclocking features Advanced To set up the advanced UEFI features H W Monitor To display current hardware status Boot To set up the default system device to locate and load the Operating System Security To set up the security features Exit To exit the current screen or the UEFI SETUP UTILITY Use lt gt key or lt gt key to choose among the selections on the menu bar and then press Enter to get into the sub screen You can also use the mouse to click your required item 23 3 1 2 Navigation Keys Please check the following table for the function description of each navigation key Navigation Key s Function Description Moves cursor left or right to select Screens p H Moves cursor up or down to select items To change option for the selected items lt Enter gt To bring up the selected screen lt F1 gt To display the General Help Screen lt F7 gt Discard changes F9 To load optimal default values for all the settings lt F10 gt To save changes and exit the UEFI SETUP UTILITY lt F12 gt Print screen lt ESC gt
21. o 9 Al 4 12V Digital UO Header Pin Signal Name Pin Signal Name 10 pin JGPIO1 10 GP24 GP20 see p 8 No 15 NO ODD GP25 GP21 Eet GP26 6 GP22 7 GP27 LS GP23 9 9 PWR 10 GND IL 20 Panel Brightness and 1 Volume UP Speaker Volume Control 2 Volume DOWN 7 pin BUT VOL1 3 PANEL PWR Down see p 8 No 26 4 Panel BackLight UP 5 Panel BackLight Down 6 GND 7 GND Panel BackLight Inverter 1 2 GND connector 3 Panel Backlight Control l E 4 Panel Backlight Enable see p 8 No 27 5 6 Panel Backlight Power 6 pin BLT PWR2 2 Serial ATA SATA Serial ATA2 SATA2 Hard Disks Installation This motherboard adopts Intel NM10 chipset that supports Serial ATA SATA Serial ATA2 SATA2 hard disks You may install SATA SATA2 hard disks on this motherboard for internal storage devices This section will guide you to install the SATA SATA2 hard disks STEP 1 Install the SATA SATA2 hard disks into the drive bays of your chassis STEP 2 Connect the SATA power cable to the SATA SATA2 hard disk STEP 3 Connect one end of the SATA data cable to the motherboard s SATA2 con nector STEP 4 Connect the other end of the SATA data cable to the SATA SATA2 hard disk 2 8 Hot Plug Function for SATA SATA2 HDDs This motherboard supports Hot Plug function for SATA SATA2 in AHCI mode Intel NM10 chipset provides hardware support for Advanced Host controller Interface AHCI
22. oard parallel port WDT Timeout Reset This allows users to enable disable the Watch Dog Timer timeout to reset system The default value is Disabled 29 3 3 5 ACPI Configuration Aptio Setup Utility Copyright C Suspend to RAM Auto Suspend to RAM Use this item to select whether to auto detect or disable the Suspend to RAM feature Select Auto will enable this feature if the OS supports it S3 Video Repost Use this to enable disable S3 Video Repost The default value is Enabled PS 2 Keyboard Power On Use this item to enable or disable PS 2 keyboard to turn on the system from the power soft off mode PCI Devices Power On Use this item to enable or disable PCI devices to turn on the system from the power soft off mode Ring In Power On Use this item to enable or disable Ring In signals to turn on the system from the power soft off mode RTC Alarm Power On Use this item to enable or disable RTC Real Time Clock to power on the system USB Keyboard Remote Power On Use this item to enable or disable USB Keyboard Remote to power on the system USB Mouse Power On Use this item to enable or disable USB Mouse to power on the system 30 3 3 6 USB Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc USB 2 0 Controller Enabled USB 2 0 Controller Use this item to enable or disable the use of USB 2 0 controller Legacy USB Support Use this option to select legacy support
23. on of the expansion card and make necessary hardware settings for the card before you start the installation Step 2 Remove the system unit cover if your motherboard is already installed in a chassis Step 3 Remove the bracket facing the slot that you intend to use Keep the screws for later use Step 4 Align the card connector with the slot and press firmly until the card is completely seated on the slot Step 5 Fasten the card to the chassis with screws Step 6 Replace the system cover 13 2 5 Jumpers Setup The illustration shows how jumpers are setup When the jumper cap is placed on pins the jumper is Short If no jumper cap y i is placed on pins the jumper is Open The illustration shows a 3 pin jumper whose ee MT t pint and pin2 are Short when jumper cap Short Open is placed on these 2 pins Clear CMOS Jumper CLRCMOS1 12 2 3 see p 8 No 17 e of Be o Default Clear CMOS Note CLRCMOS 1 allows you to clear the data in CMOS To clear and reset the system parameters to default setup please turn off the computer and unplug the power cord from the power supply After waiting for 15 seconds use a jumper cap to short pin2 and pin3 on CLRCMOS 1 for 5 seconds However please do not clear the CMOS right after you update the BIOS If you need to clear the CMOS when you just finish updating the BIOS you must boot up the system first and then shut it down before you do the clear CMOS action
24. ou select this option it will pop out the following message Discard changes Select OK to discard all changes Load UEFI Defaults Load UEFI default values for all the setup questions F9 key can be used for this operation Launch EFI Shell from filesystem device Attempts to Launch EFI Shell application Shell64 efi from one of the available filesystem devices 36 Chapter 4 Software Support 4 1 Install Operating System This motherboard supports Microsoft Windows operating systems 7 32 bit Be cause motherboard settings and hardware options vary use the setup procedures in this chapter for general reference only Refer to your OS documentation for more information 4 2 Support CD Information The Support CD that came with the motherboard contains necessary drivers and useful utilities that enhance the motherboard s features 4 2 1 Running The Support CD To begin using the support CD insert the CD into your CD ROM drive The CD automatically displays the Main Menu if AUTORUN is enabled in your computer If the Main Menu did not appear automatically locate and double click on the file ASSETUP EXE from the BIN folder in the Support CD to dis play the menus 4 2 2 Drivers Menu The Drivers Menu shows the available device s drivers if the system detects installed devices Please install the necessary drivers to activate the devices 4 2 3 Utilities Menu The Utilities Menu shows the application software that
25. ur the updated version will be available on ASRock website without further notice You may find the latest VGA cards and CPU support lists on ASRock website as well ASRock website http www asrock com If you require technical support related to this motherboard please visit our website for specific information about the model you are using www asrock com support index asp 1 1 Package Contents ASRock IMB 130 Motherboard Mini ITX Form Factor 6 7 in x 6 7 in 17 0 cm x 17 0 cm ASRock IMB 130 Driver CD ASRock IMB 130 Jumper setting instruction 1 x I O Panel Shield 2 X SATA HDD Cables 1 x SATA Power Cable 2 x COM Port Cables 1 x DC IN Cable 1 2 Specifications UD Dimensions Mini ITX 6 7 in x 6 7 in Factor ij Intel Dual Core Atom CedarView Processor e Core 2 Number nid Max Speed D2550 N2800 1 86 GHz N2600 1 6GHz Expansion msaTa Jo Slot AAA AAA CFast Card Saan RI Memory l N2600 2GB N2600 1 x SO DIMM Controller Intel PowerVR SGX545 Support Directx9 Controller compliant Pixel Shader v3 0 and OGL 3 0 eT Etel LVDS Dual Channel 24bits max resolution 1920x1200 HDMI Supports HDMI 1 3a max resolution 1920x1200 D2550 N2600 N2800 DVI Ethernet Max Data Transfer SATA2 3 0Gb s Rate HDM G Ethernet USB 4 USB 2 0 compliant Audio 2 Mic in Line out D S L S 1 x D Sub GA VI i rt USB Serial 1 RS 232 422 485 1 RS232 PS 2 2 1 x keyboard and 1 x mouse USB 3 U
Download Pdf Manuals
Related Search