ASRock H77TM-ITX Owner's Manual
Contents
1. 9 MediaEspresso 6 5 Trial Google Chrome Browser Toolbar ro er Monitor CPU Chassis Fan Multi Speed Control Voltage Monitoring 12V 5V 3 3V CPU Vcore Microsoft Windows 8 8 64 bit 7 7 64 bit Vista Vista 64 bit XP XP 64 bit compliant FCC CE WHQL ErP EuP Ready ErP EuP ready power supply is required 05 Certifications For detailed product information please visit our website http www asrock com WARNING Please realize that there is a certain risk involved with over clocking including adjusting the setting in the BIOS applying Untied Overclocking Technology or using third party overclock ing tools Overclocking may affect your system s stability or even cause damage to the components and devices of your system It should be done at your own risk and expense We are not responsible for possible damage caused by overclocking CAUTION fl Due to limitation the actual memory size may be less than 4GB for the reservation for system usage under Windows 32 bit operating systems Windows 64 bit operating systems do not have such limitations You can use ASRock XFast RAM to uti lize the memory that Windows cannot use PCIE 3 0 is only supported with Intel Ivy Bridge CPU With In tel Sandy Bridge CPU it only supports PCIE 2 0 Intel HD Graphics Built in Visuals and the VGA outputs can be supported only with processors which are GPU integrated Intel Qu2. Ne 1 33 This COM1 header supports a serial port module HDMI_SPDIF Header This header provides SPDIF 2 pin HDMI_SPDIF1 ul audio output to HDMI VGA see p 13 15 17 No 25 SEO cards allowing the system to connect HDMI Digital TV projector LCD devices Please connect the HDMI SPDIF connector of a HDMI VGA card to this header Backlight amp Amp 1 BKLT EN Volume Control o 2 BKLT_PWM Header S 3 8 BLT_VOL1 S 4 BKLT_PWR see p 13 15 17 No 17 5 GND 6 GND 7 Brightness Up 8 Brightness Down Digital MIC Header 1 1 5V 5 pin DMIC1 2 No pin see p 13 15 17 No 24 2 SPDIF OUT DMIC CLK 3 GND 4 DMIC DATA 5 3 3V Home Theater PC Header 7 pin HTPC1 see p 13 15 17 No 29 Signal Name Signal Name HDMI 7 Power Button SMB DATA 5 3 3V Standby 34 LPC Debug Header 13 pin LPC1 see p 13 15 17 No 30 35 PIN Signal Name 3V PIN Signal Name 3V GND LAD3 LAD1 LFRAME GND 11 3V 9 7 5 2 9 Jumpers Setup When the jumper cap is placed on the pins the jumper is Short If no jumper J cap is placed on the pins the jumper is Open The illustration shows a 3 pin Neg Neg jumper whose 1 and pin2 are Short Short Open when a jumper cap is placed on these 2 pins Clear CMOS Jumper 12 2 3 CLRCMOS1 00 2 on see p 13 15 17 No 31 Default C
3. 1 Consumer Infrared Module Header CIR1 SATA2 Connector SATA 0 USB 2 0 Header USB6 7 Mini PCI Express Slot MINI PCIE1 USB 3 0 Header USB3 0 1 SATA Power Connector SATA POW1 Power LED Header PLED1 System Panel Header PANEL 1 Backlight Power Jumper BKT PWR1 Panel Power Jumper PNL PWR1 LVDS Connector LVDS1 2 x 204 pin DDR3 SO DIMM Slots DDR3 A1 DDR3 B1 Backlight amp Amp Volume Control Header BLT VOL1 COM Port Header COM1 1155 Pin CPU Socket USB 2 0 Header 05 4 5 SPI Flash Memory 32Mb CPU Fan Connector CPU 1 PCI Express 3 0 x4 Slot PCIE1 Digital MIC Header DMIC1 HDMI SPDIF Header HDMI SPDIF1 Front Panel Audio Header HD AUDIO1 Analog Surround Audio Header HD AUDIO2 3W Audio AMP Output Wafer Header SPEAKER1 Home Theater PC Header HTPC1 LPC Debug Header LPC1 Clear CMOS Jumper CLRCMOS1 18 1 7 Panel H77TM ITX DC Jack USB 2 0 Ports USB01 DVI I DVI1 eSATA Connector eSATA1 LAN RJ 45 Port USB 3 0 Ports USB23 Front Speaker Lime Microphone Pink HDMI Port HDMI1 Please use a 19V power adaptor for the DC jack This jack accepts dual barrel plugs with an inner diameter of 2 5 mm and an outer diameter of 5 5 mm where the inner contact is 8 10 through 19 10 VDC and the shell is GND The maximum current rating depends on the power adaptor The following are examples of power adaptors that may be used DELTA DELTA ADP 1
4. Adjust Recording Volume Analog Surround Signal Name PIN Signal Name Audio Header SENSE KEY 17 pin HD AUDIO2 LFE see p 13 15 17 No 27 14 AGND 13 Center 12 5 Rear R 11 A GND 10 AGND 9 5 Rear 8 6 32 3W Audio AMP Output Wafer Header 4 pin SPEAKER1 see p 13 15 17 No 28 Front R Front R Front Front L 1 Please connect the chassis speaker to this header Power LED Header 8 pin PLED1 see p 13 15 17 No 11 Oy PLED Oy PLED PLED Please connect the chassis power LED to this header to indicate system power status The LED is on when the system is operating The LED keeps blinking in 51 53 state The LED is off in S4 state or S5 state power off Chassis Fan Connector 4 pin CHA_FAN1 see p 13 15 17 No 4 FAN_SPEED_CONTROL SPEED 12V GND 1234 Please connect a fan cable to the fan connector and match the black wire to the ground pin CPU Fan Connectors 4 pin CPU_FAN1 see p 13 15 17 No 22 FAN SPEED coNTROL TO 4 FAN SPEED Og 3 12V 2 GND Oo j Though this motherboard provides a 4 Pin CPU fan Quiet Fan connector 3 Pin CPU fans can still work even without fan speed control If you plan to connect a 3 Pin CPU fan please connect it to Pin 1 3 Serial Port Header 10 pin COM1 see p 13 15 17 No 18 coMPwn pcp O O dsr RXD O OFRTS TXD1O O CTS DTR O O COM PWR RI evo
5. 0 Header 05 4 5 SPI Flash Memory 32Mb CPU Fan Connector CPU 1 PCI Express 3 0 x4 Slot PCIE1 Digital MIC Header DMIC1 HDMI SPDIF Header HDMI SPDIF1 Front Panel Audio Header HD AUDIO1 Analog Surround Audio Header HD AUDIO2 3W Audio AMP Output Wafer Header SPEAKER1 Home Theater PC Header HTPC1 LPC Debug Header LPC1 Clear CMOS Jumper CLRCMOS1 16 1 6 31 30 29 28 27 26 Motherboard Layout H61TM ITX 12 DC Jack USB 3 0 T USBO B USB1 CMOS Battery DVI1 L CLRCMOS1 LPC1 HDMI eSATA1 34 5678 9 10 11 42 CHA FANT ci uses 1 55 3 0 DDR3 CUE T SATA 1 SATA 0 MINI PCIE1 1 vs 7 POWI USB3 0 1 2 DDR3 B1 DI Intel RJ 45 USB 2 0 USB2 B USB3 L MESI d AUDIO Mic In HLE CPU FANT AUDIO2 Front ussas wom seo puel PCIE1 z 111 I Designed in Taipei ah H61 DDR3 A1 4 61 A EE 1 44 25 24 23 2 221 17 19 1 20 1 2 3 4 5 6 7 8 Intel H61 Chipset SATA2 Connector SATA 1 USB 2 0 Header USB8 Chassis Fan Connector CHA
6. Clock to power on the system USB Keyboard Remote Power On Use this to enable or disable the USB Keyboard Remote to power on the system USB Mouse Power On Use this to enable or disable the USB Mouse to power on the 57 System CSM Please disable CSM when Fast Boot is enabled The default value is Enabled 58 3 4 9 USB Configuration USB 2 0 Controller Use this to enable or disable the USB 2 0 controller USB 3 0 Controller Use this to enable or disable the USB 3 0 controller Legacy USB Support Use this to select legacy support for USB devices There are four configuration options Enabled Auto Disabled and UEFI Setup Only The default value is Enabled Please refer to the descrip tions below for details of these four options Enabled Enables support for legacy USB Auto Enables legacy support if USB devices are connected Disabled USB devices are not allowed to be used under legacy OS and UEFI setup when Disabled is selected If you have USB compatibility issues it is recommended to select Disabled to enter the OS UEFI Setup Only USB devices are allowed to be used only under UEFI setup and Windows Linux OS Legacy USB 3 0 Support Use this to enable or disable legacy support for USB 3 0 devices The default value is Enabled USB Compatibility Patch Please enable this if your USB devices encounter compatibility problems 59 3 4 10 Trusted Computing Security Device Sup
7. DVI1 eSATA Connector eSATA1 LAN RJ 45 Port USB 2 0 Ports USB23 Front Speaker Lime Microphone Pink HDMI Port HDMI1 Please use a 19V power adaptor for the DC jack This jack accepts dual barrel plugs with an inner diameter of 2 5 mm and an outer diameter of 5 5 mm where the inner contact is 8 10 through 19 10 VDC and the shell is GND The maximum current rating depends on the power adaptor The following are examples of power adaptors that may be used DELTA DELTA ADP 150TB 150W 19V HP HP TBC BA52 150W 19V FSP FSP FSP150 ABAN1 150W 19V There are two LEDs on the LAN port Please refer to the table below for the LAN port LED indications z ACT LINK SPEED LAN Port LED Indications LED LED Activity Link LED SPEED LED L Off No Link Off 10Mbps connection Blinking Data Activity Orange 100Mbps connection 100Mbps connection 1Gbps connection LAN Port 21 Chapter 2 Installation This is a Thin Mini ITX form factor motherboard Before you install the motherboard study the configuration of your chassis to ensure that the motherboard fits into it Pre installation Precautions Take note of the following precautions before you install motherboard com ponents or change any motherboard settings 1 sure to unplug the power cord before installing or removing the motherboard Failure to do so may cause physical injuries to you and damages to motherboard com ponents 2 n order to
8. IGReck H77TM ITX B75TM ITX H61TM ITX User Manual Version 1 0 Published January 2013 Copyright 2013 ASRock INC All rights reserved Copyright Notice No part of this manual may be reproduced transcribed transmitted or translated in any language in any form or by any means except duplication of documentation by the purchaser for backup purpose without written consent of ASRock Inc Products and corporate names appearing in this manual may or may not be regis tered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe Disclaimer Specifications and information contained in this manual are furnished for informa tional use only and subject to change without notice and should not be constructed as a commitment by ASRock ASRock assumes no responsibility for any errors or omissions that may appear in this manual With respect to the contents of this manual ASRock does not provide warranty of any kind either expressed or implied including but not limited to the implied warran ties or conditions of merchantability or fitness for a particular purpose In no event shall ASRock its directors officers employees or agents be liable for any indirect special incidental or consequential damages including damages for loss of profits loss of business loss of data interruption of business and the like even if ASRock ha
9. The default value is Auto 47 CPU Thermal Throttling Use this to enable CPU internal thermal control mechanism to keep the CPU from overheated The default value is Enabled No Execute Memory Protection No Execution NX Memory Protection Technology is an enhance ment to the IA 32 Intel Architecture An IA 32 processor with No Execute NX Memory Protection can prevent data pages from being used by malicious software to execute codes This option will be hidden if the current CPU does not support No Excute Memory Protection Intel Virtualization Technology When this option is set to Enabled a VMM Virtual Machine Archi tecture can utilize the additional hardware capabilities provided by Vanderpool Technology This option will be hidden if the installed CPU does not support Intel Virtualization Technology Hardware Prefetcher Use this turn on off the MLC streamer prefetcher Adjacent Cache Line Prefetch Use this to turn on off prefetching of adjacent cache lines 48 3 4 2 North Bridge Configuration ASRock 5 Primary Graphics Adapter This allows you to select Onboard or PCI Express as the primary graphics adapter The default value is PCI Express PCIE1 Link Speed This allows you to select PCIE1 Link Speed Share Memory This allows you to configure share memory The default value is Auto IGPU Multi Moniter This allows you to enable or disable IGPU Multi Moniter The de fault value is Disa
10. avoid damage from static electricity to the moth erboard s components NEVER place your motherboard directly on a carpet Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components 3 Hold components by the edges and do not touch the ICs 4 Whenever you uninstall any components place them on a grounded anti static pad or in the bag that comes with the components 5 When placing screws to secure the motherboard to the chassis please do not over tighten the screws Doing so may damage the motherboard 22 2 1 Installing the CPU In order to provide the LGA 1155 CPU Sockets more protection and make the installation process easier ASRock has added a new protection cover on top of the load plate to replace the former PnP caps that were under the load plate For the installation of Intel 1155 Pin CPUs with the new protection cover please follow the steps below Contact Array 8 Socket Body ya cru 1155 Pin Socket Overview Before you insert the 1155 Pin CPU into the socket please check if the CPU surface is unclean or if there are any bent pins in the socket Do not force to insert the CPU into the Socket if above situation is found Otherwise the CPU will be seriously damaged Step 1 Open the socket Step 1 1 Disengage the lever by pressing it down and sliding it out of the hook You do not have to remove the protection cover Ste
11. bit operating sys tems ASRock XFast RAM shortens the loading time of previously visited websites making web surfing faster than ever And it also boosts the speed of Adobe Photo shop 5 times faster Another advantage of ASRock XFast RAM is that it reduces the frequency of accessing your SSDs or HDDs in order to extend their lifespan ASRock Crashless BIOS ASRock Crashless BIOS allows users to update their BIOS without fear of failing If power loss occurs during the BIOS updating process ASRock Crashless BIOS will automatically finish the BIOS update procedure after regaining power Please note that BIOS files need to be placed in the root directory of your USB disk Only USB 11 2 0 ports support this feature ASRock OMG Online Management Guard Administrators are able to establish an internet curfew or restrict internet access at specified times via OMG You may schedule the starting and ending hours of internet access granted to other users In order to prevent users from bypassing OMG guest accounts without permission to modify the system time are required ASRock Internet Flash ASRock Internet Flash searches for available UEFI firm ware updates from our servers In other words the sys tem can auto detect the latest UEFI from our servers and flash them without entering Windows OS ASRock Fast Boot With ASRock s exclusive Fast Boot technology it takes less than 1 5 seconds to logon to Windows 8 from a cold boot No mor
12. ig ports on the I O panel there see p 13 15 17 No 9 is one USB 3 0 header on 15 51919191919191916 1 15492249255 this motherboard The USB 8552058 pr 3 0 header can support two Pi 85 ost 22 USB 2 0 ports Consumer Infrared SAT This header can be used to connect the remote controller receiver Module Header 7 pin CIR1 see p 13 15 17 No 5 31 Front Panel Audio Header ONPRESENCE This is an interface for the MIC_RET pi HD RUBIO 9 front panel audio cable that 5 allows convenient connec Qu t tion and control of audio OUT2 R MIC2 R devices 1 High Definition Audio supports Jack Sensing but the panel wire L the chassis must support HDA to function correctly Please follow the instructions in our manual and chassis manual to install your system 2 If you use an AC 97 audio panel please install it to the front panel audio header by the steps below A Connect Mic IN MIC to MIC2 L B Connect Audio R RIN to OUT2 R and Audio L LIN to OUT2 L C Connect Ground GND to Ground GND D MIC RET and OUT RET are for HD audio panel only You don t need to connect them for AC 97 audio panel E To activate the front mic For Windows XP XP 64 bit OS Select Mixer Select Recorder Then click FrontMic For Windows 8 8 64 bit 7 7 64 bit Vista Vista 64 bit OS Go to the Tab in the Realtek Control panel
13. or disable Active Page Threshold Sup port The default is Disabled 54 3 4 6 Intel R Smart Connect Technology ASRock 5 Intel R Smart Connect Technology Use this to enable or disable Intel R Smart Connect Technology Intel R Smart Connect Technology keeps your e mail and social networks such as Twitter Facebook etc updated automatically while the computer is in sleep mode The default is Enabled 55 3 4 7 Super IO Configuration MSReck UEFI Serial Port Use this to enable or disable the onboard serial port Serial Port Address Use this to set the address for the onboard serial port Configura tion options 3F8h IRQ4 and 3E8h IRQ4 56 3 4 8 ACPI Configuration MSRock UEFI setup utility Suspend to RAM Use this to select whether to auto detect or disable Suspend to RAM Select Auto to enable if the OS supports it Check Ready Bit Use this to enable or disable Check Ready Bit ACPI HPET Table Use this to enable or disable the ACPI HPET Table The default value is Enabled Please set this option to Enabled if you plan to use this motherboard to submit Windows certification PCI Devices Power On Use this to enable or disable the PCI devices to turn on the system from power soft off mode Ring In Power On Use this to enable or disable the Ring In signals to turn on the sys tem from power soft off mode RTC Alarm Power On Use this to enable or disable the RTC Real Time
14. 50TB 150W 19V HP HP TBC BA52 150W 19V FSP FSP FSP150 ABAN1 150W 19V There are two LEDs on the LAN port Please refer to the table below for the LAN port LED indications z ACT LINK SPEED LAN Port LED Indications LED LED Activity Link LED SPEED LED L Off No Link Off 10Mbps connection Blinking Data Activity Orange 100Mbps connection 100Mbps connection 1Gbps connection LAN Port 19 1 8 I O Panel B75TM ITX DC Jack USB 2 0 Ports USB01 DVI I DVI1 eSATA Connector eSATA1 LAN RJ 45 Port USB 3 0 Ports USB23 Front Speaker Lime Microphone Pink HDMI Port HDMI1 Please use a 19V power adaptor for the DC jack This jack accepts dual barrel plugs with an inner diameter of 2 5 mm and an outer diameter of 5 5 mm where the inner contact is 8 10 through 19 10 VDC and the shell is GND The maximum current rating depends on the power adaptor The following are examples of power adaptors that may be used DELTA DELTA ADP 150TB 150W 19V HP HP TBC BA52 150W 19V FSP FSP FSP150 ABAN1 150W 19V There are two LEDs on the LAN port Please refer to the table below for the LAN port LED indications ACT LINK SPEED LAN Port LED Indications LED LED Activity Link LED SPEED LED Off No Link Off 10Mbps connection Blinking Data Activity Orange 100Mbps connection 100Mbps connection 1Gbps connection LAN Port 20 1 9 I O Panel H61TM ITX DC Jack USB 3 0 Ports USB01 DVI I
15. E CPU FANT AUDIO2 Front ussas PCIE1 EL CELE I Designed in Taipei ah H77 DDR3 A1 4 H77TM ITX EER 14 BET PWRI PNLEPWRI LVDS1 BLT VOLI ips 25 24 23 2 221 13 19 20 1 2 3 4 5 6 7 8 Intel H77 Chipset SATA3 Connector SATA 1 USB 2 0 Header USB8 Chassis Fan Connector CHA 1 Consumer Infrared Module Header CIR1 SATA3 Connector SATA 0 USB 2 0 Header USB6 7 Mini PCI Express Slot MINI PCIE1 USB 3 0 Header USB3 0 1 SATA Power Connector SATA POW1 Power LED Header PLED1 System Panel Header PANEL 1 Backlight Power Jumper BKT PWR1 Panel Power Jumper PNL PWR1 LVDS Connector LVDS1 2 x 204 pin DDR3 SO DIMM Slots DDR3 A1 DDR3 B1 Backlight amp Amp Volume Control Header BLT VOL1 COM Port Header COM1 1155 Pin CPU Socket USB 2 0 Header 05 4 5 SPI Flash Memory 32Mb CPU Fan Connector CPU 1 PCI Express 3 0 x4 Slot PCIE1 Digital MIC Header DMIC1 HDMI SPDIF Header HDMI SPDIF1 Front Panel Audio Header HD AUDIO1 Analog Surround Audio Header HD AUDIO2 3W Audio AMP Output Wafer Header SPEAKER1 Home Theater PC Header HTPC1 LPC Debug Header LPC1 Clear CMOS Jumper CLRCMOS1 14 1 5 31 30 29 28 27 26 Motherboard Layout B75TM ITX 12 DC Jack USB 2 0 T USBO B USB1 CMOS Battery D
16. Installing the CPU Fan and Heatsink 25 2 3 Installing Memory Modules DIMM 26 2 4 Expansion Slots PCI Express Slots 27 2 5 Installing Serial SATA2 SATA3 Hard Disks 28 26 Power Connectors e rte ree 29 2 7 Installing the System 30 2 8 Onboard Headers and Connectors 31 2 9 J mpers Set p eric 36 2 10 Operating System 37 2 11 Installing Drivers one 38 3 UEFI SETUP UTILITY iiie nnns 39 3 1 3 2 3 3 3 4 3 5 3 6 3 7 3 8 3 9 nisse E 39 3 1 1 UEFI Men Bar cerent 39 3 1 2 Navigation 40 Main vie 41 OG Tweaker Screen etre ttes 42 Advanced SC ied cree rede 46 3 4 1 CPU Configuration 47 3 4 2 North Bridge 49 3 4 3 South Bridge Configuration 51 3 4 4 Storage Configuration 53 3 4 5 Intel R Rapid Start Technology 54 3 4 6 Intel R Smart Connect Technology 55 3 4 7 Supe
17. VI1 L CLRCMOS1 LPC1 HDMI eSATA1 34 5678 9 10 11 CHA FANT ci uses 1 55 3 0 DDR3 CUE T SATA 1 SATA 0 MINI PCIE1 1 vs 7 POWI USB3 0 1 DDR3 B1 12 PLEDI Intel RJ 45 USB 3 0 T USB2 B USB3 L MER d AUDIO Mic In HLE CPU FANT AUDIO2 Front ussas PCIE1 EL CELE I Designed in Taipei ah B75 DDR3 A1 4 75 EER 14 BET PWRI PNLEPWRI LVDS1 BLT VOLI ips 25 24 23 2 221 15 19 20 1 2 3 4 5 6 7 8 Intel B75 Chipset SATA2 Connector SATA 1 USB 2 0 Header USB8 Chassis Fan Connector CHA 1 Consumer Infrared Module Header CIR1 SATA3 Connector SATA 0 USB 2 0 Header USB6 7 Mini PCI Express Slot MINI PCIE1 USB 3 0 Header USB3 0 1 SATA Power Connector SATA POW1 Power LED Header PLED1 System Panel Header PANEL 1 Backlight Power Jumper BKT PWR1 Panel Power Jumper PNL PWR1 LVDS Connector LVDS1 2 x 204 pin DDR3 SO DIMM Slots DDR3 A1 DDR3 B1 Backlight amp Amp Volume Control Header BLT VOL1 COM Port Header COM1 1155 Pin CPU Socket USB 2
18. ation Storage Configuration Intel R Rapid Start Technology Intel R Smart Connect Technology Super IO Configuration ACPI Configuration USB Configuration and Trusted Computing MSRock UEFI setup Utility IN Setting wrong values in this section may cause the system to malfunction 46 3 4 1 CPU Configuration Intel Hyper Threading Technology To enable this feature a computer system with an Intel processor that supports Hyper Threading technology and an operating system that includes optimization for this technology such as Microsoft Windows XP Vista 7 8 is required Set to Enabled if using Microsoft Windows XP Vista 7 8 or Linux kernel version 2 4 18 or higher This option will be hidden if the installed CPU does not support Hyper Threading technology Active Processor Cores Use this to select the number of cores to enable in each processor package The default value is All Enhanced Halt State C1E All processors support the Halt State C1 C1 state is supported through the native processor instructions HLT and MWAIT and re quires no hardware support from the chipset In C1 power state the processor maintains the context of the system caches CPU C3 State Support Use this to enable or disable CPU C3 report to OS CPU C6 State Support Use this to enable or disable CPU C6 report to OS Package C State Support Configure options that will be programmed into C State package limit register
19. being updated the following they may not exactly match what you see on your screen 3 1 1 UEFI Menu Bar The top of the screen has a menu bar with the following selections Main For setting system time date information OC Tweaker For overclocking configurations Advanced For advanced system configurations Tool Useful tools H W Monitor Displays current hardware status Boot For configuring boot settings and boot priority Security For security settings Exit Exit the current screen or the UEFI Setup Utility 39 3 1 2 Navigation Keys Use lt lt gt key or lt gt key to choose among the selections on the menu bar and use lt gt key or lt gt key to move the cursor up or down to select items then press Enter to get into the sub screen You can also use the mouse to click your required item Please check the following table for the descriptions of each navigation key Description To change option for the selected items Switch to next function PGUP Goto the previous page Go to the next page Go to the top of the screen Go to the bottom of the screen Fi To display the General Help Screen Discard changes and exit the SETUP UTILITY Load default values for all the settings lt F10 gt Save changes and exit the SETUP UTILITY Print screen ESC the Exit Screen or exit the current screen 40 3 2 Main Screen When you enter the UEFI SETUP UTILITY the Main scree
20. bled If you wish to install a PCI Express card under Windows Vista OS please disable this option Render Standby Use this to enable or disable Render Standby by the Internal Graphics Device The default value is Enabled LVDS Configuration This allows you to enable or disable the Onboard LVDS Panel Type Selection Use this to select a panel type Primary IGFX Boot Display Use this to select the video device which will be activated during POST 49 Volume Control Use this to fine tune the desired volume 50 3 4 3 South Bridge Configuration ASRock UEFI 5 Onboard HD Audio Select Auto Enabled or Disabled for the onboard HD Audio If you select Auto the onboard HD Audio will be disabled when a Sound Card is plugged Front Panel Select Auto or Disabled for the onboard HD Audio Front Panel External Panel Select Auto or Disabled for the External Audio Panel Onboard HDMI HD Audio This allows you to enable or disable the Onboard HDMI HD Audio Onboard LAN This allows you to enable or disable the Onboard LAN Wireless This allows you to enable or disable the Wireless function Radio Controller This allows you to enable or disable the Radio Controller Deep Sleep Mobile platforms support Deep S4 S5 in DC only and desktop plat forms support Deep S4 S5 in AC only Configuration options Dis abled Enabled in S5 and Enabled in S4 and S5 Restore on AC Power Loss This allows you to set the power
21. dex asp 1 1 Package Contents ASRock H77TM ITX B75TM ITX H61TM ITX Motherboard Thin Mini ITX Form Factor 6 7 in x 6 7 in 17 0 cm x 17 0 cm ASRock H77TM ITX B75TM ITX H61TM ITX Quick Installation Guide ASRock H77TM ITX B75TM ITX H61TM ITX Support CD 1 x I O Panel Shield 1 2 Specifications Thin Mini ITX Form Factor 6 7 in x 6 7 in 17 0 cm x 17 0 Elie dit Compatible with Mini ITX Solid Capacitors for CPU power Supports 3rd and 2nd Generation Intel Core i7 15 i3 in LGA1155 Package Supports Intel Turbo Boost 2 0 Technology Supports Hyper Threading Technology Intel H77 B75 H61 Supports Intel Small Business Advantage B75TM ITX Supports Intel Rapid Start Technology and Smart Connect Technology Dual Channel DDR3 Memory Technology 2 x DDR3 SO DIMM slots Supports DDR3 1600 1333 1066 non ECC un buffered memory Max capacity of system memory 16GB see CAUTION 1 1 x PCI Express 3 0 x4 slot PCIE1 x4 mode see CAU TION 2 1 x mini PCI Express slot Chipset Expansion Slots Supports Intel HD Graphics Built in Visuals see CAUTION 3 Pixel Shader 5 0 DirectX 11 with Intel Ivy Bridge CPU Pixel Shader 4 1 DirectX 10 1 with Intel Sandy Bridge CPU Max shared memory 1760MB with Intel Ivy Bridge CPU Max shared memory 1759MB with Intel Sandy Bridge CPU Three VGA Output options HDMI DVI I and LVDS Supports HDMI 1 4a Technolog
22. e maximum instantaneous current allowed for the primary plane The default value is Auto Secondary Plane Current Limit Use this to configure the maximum instantaneous current allowed for the secondary plane The default value is Auto GT OverClocking Support Use this to enable or disable GT OverClocking Support The default value is Disabled DRAM Timing Configuration Load XMP Setting Use this to load XMP settings Configuration options Auto De fault Profile 1 and Profile 2 The default value is Auto DRAM Frequency If Auto is selected the motherboard will detect the memory module s inserted and assign the appropriate frequency automati cally DRAM Configuration ASRock UEFI Setup Utiity x EN p M c M p DE M p MM M po c mE p MN DRAM tCL Use this to change CAS Latency tCL Auto Manual settings The default is Auto 43 DRAM tRCD Use this to change RAS to CAS Delay tRCD Auto Manual set tings The default is Auto DRAM tRP Use this to change Row Precharge Time tRP Auto Manual set tings The default is Auto DRAM tRAS Use this to change RAS Active Time tRAS Auto Manual settings The default is Auto Command Rate CR Use this to change Command Rate CR Auto Manual settings The default is Auto DRAM tWR Use this to change Write Recovery Time tWR Auto Manual set tings The default is Auto DRAM tRFC Use this to change Refres
23. e system ASRock APP Charger If you desire a faster less restricted way of charging your Apple devices such as iPhone iPad iPod Touch ASRock has prepared a wonderful solution for you ASRock APP Charger Simply install the APP Charger driver it makes your iPhone charge much quickly from your computer and up to 4096 faster than before ASRock APP Charger allows you to quickly charge many Apple devices simul taneously and even supports continuous charging when your PC enters into Standby mode S1 Suspend to RAM 53 hibernation mode S4 or power off 55 With 10 APP Charger driver installed you can easily enjoy the marvelous charging experience ASRock XFast USB ASRock XFast USB can boost the performance of your USB storage devices The performance may depend on the properties of the device ASRock XFast LAN ASRock XFast LAN provides faster internet access which includes the benefits listed below LAN Application Prioritization You can configure your application s prior ity ideally and or add new programs Lower Latency in Game After setting online game s priority higher it can lower the latency in games Traffic Shaping You can watch Youtube HD videos and download simultaneously Real Time Analysis of Your Data With the status window you can easily recognize which data streams you are transferring currently ASRock XFast RAM ASRock XFast RAM fully utilizes the memory space that cannot be used under Windows 32
24. e waiting The speedy boot will completely change your user experience and behavior ASRock Restart to UEFI Windows 8 brings the ultimate boot up experience The lightning boot up speed makes it hard to access the UEFI setup ASRock Restart to UEFI allows users to enter the UEFI automatically when turning on the PC By enabling this function the PC will enter the UEFI directly after you restart ASRock Good Night LED ASRock Good Night LED technology offers you a better sleeping environment by extinguishing the unessential LEDs By enabling Good Night LED in the BIOS the Power HDD LAN LEDs will be switched off when the sys tem is powered on Good night LED will also automati cally switch off the Power and Keyboard LEDs when the System enters into Standby Hibernation mode as well 12 1 4 31 30 29 28 27 26 Motherboard Layout H77TM ITX 12 DC Jack USB 2 0 T USBO B USB1 CMOS Battery DVI1 L CLRCMOS1 LPC1 HDMI eSATA1 34 5678 9 10 11 CHA FANT ci uses 1 55 3 0 DDR3 CUE T SATA 1 SATA 0 MINI PCIE1 1 vs 7 POWI USB3 0 1 DDR3 B1 12 PLEDI Intel RJ 45 USB 3 0 T USB2 B USB3 L MER d AUDIO Mic In HL
25. h Cyle Time tRFC Auto Manual settings The default is Auto DRAM tRRD Use this to change RAS to RAS Delay tRRD Auto Manual set tings The default is Auto DRAM tWTR Use this to change Write to Read Delay tWTR Auto Manual set tings The default is Auto DRAM tRTP Use this to change Read to Precharge tRTP Auto Manual settings The default is Auto DRAM tFAW Use this to change Four Activate Window tFAW Auto Manual set tings The default is Auto DRAM tCWL Use this to change CAS Write Latency tCWL Auto Manual set tings The default is Auto ODT WR CHA Use this to change ODT CHA Auto Manual settings The default is 44 Auto ODT WR CHB Use this to change ODT CHB Auto Manual settings The default is Auto ODT NOM CHA Use this to change ODT CHA Auto Manual settings The default is Auto ODT NOM CHB Use this to change ODT CHB Auto Manual settings The default is Auto MRC Fast Boot Use this to enable or disable MRC Fast Boot The default is En abled Voltage Configuration DRAM Voltage Use this to configure DRAM Voltage The default value is Auto VTT Voltage Use this to configure VTT Voltage The default value is Auto VCCSA Voltage Use this to configure VCCSA Voltage The default value is Auto 45 3 4 Advanced Screen In this section you may set the configurations for the following items CPU Configuration Nouth Bridge Configuration South Bridge Configur
26. ick Sync Video 2 0 Intel InTru 3D Intel Clear Video HD Technology Intel Insider Intel HD Graphics 2500 4000 supported by Intel Ivy Bridge CPU Intel Quick Sync Video Intel InTru 3D Intel Clear Video HD Technology Intel HD Graphics 2000 3000 Intel Advanced Vector Extensions AVX are supported by Intel Sandy Bridge CPU 1 3 Unique Features ASRock Instant Boot ASRock Instant Boot provides an efficient way to save energy time money and improve the system s running speed It leverages the S3 and S4 ACPI features which normally enable Sleep Standby and Hibernation modes in Windows to shorten the boot time By calling S3 and S4 at a specific timing during the shutdown and startup process Instant Boot allows you to enter your Windows desktop in a few seconds ASRock Instant Flash ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM This convenient BIOS update tool allows you to update the system BIOS without entering operat ing systems first like MS DOS or Windows With this utility you can press F6 or F2 during POST to enter the BIOS setup menu to access ASRock Instant Flash Just launch this tool and save the new BIOS file to your USB flash drive floppy disk or hard drive then you can update your BIOS in a few clicks without preparing an additional floppy diskette or other complicated flash utili ty Please be noted that the USB flash drive or hard drive must use FAT32 16 12 fil
27. k to improve heat dissipation Ensure that the CPU and the heatsink are securely fastened and in good contact with each other Then connect the CPU fan to the CPU FAN connector CPU 1 see p 13 15 17 No 22 For proper installation please kindly refer to the instruction manuals of your CPU fan and heatsink Below is an example to illustrate the installation of a heatsink and fan for 1155 Pin CPUs Step 1 Apply thermal interface material onto the center of the IHS on the socket s surface Step 2 Place the heatsink onto the socket Ensure that the fan cables are faced on the side closest to the CPU fan connec tor on the motherboard CPU 1 see p 13 15 17 No 22 Step 3 Align the fasteners with the holes on the motherboard Step 4 Rotate the fastener clockwise then press the fastener caps down with your thumb to install and lock Repeat with the remaining fasteners If you press down the fasteners without rotating them clock wise the heatsink cannot be secured on the motherboard Step 5 Connect the CPU fan connector with the fan header on the motherboard Step 6 Secure redundant cable with tie wrap to ensure that the cable does not interfere with the fan s operation or contact other components Press Down 2 25 2 3 Installing Memory Modules DIMM This motherboard provides two 204 pin DDR3 Double Data Rate 3 SO DIMM slots Step 1 Align a DIMM on the slot such that
28. lear CMOS CLRCMOS allows you to clear the data in CMOS To clear and reset the system parameters to default setup please turn off the computer and unplug the power cord from the power supply After waiting for 15 seconds use a jumper cap to short pin2 and pin3 on CLRCMOS 1 for 5 seconds However please do not clear the CMOS right after you update the BIOS If you need to clear the CMOS when you just finish updating the BIOS you must boot up the system first and then shut it down before you do the clear CMOS action Please be noted that the password date time user default profile 1394 GUID and MAC address will be cleared only if the CMOS battery is removed Backlight Power Jumper Boo 1 2 12V 3 pin BKT PWR1 123 2 3 19V see p 13 15 17 No 13 Panel Power Jumper Boo 1 2 3V 3 pin PNL PWR1 2 8 5V see p 13 15 17 No 14 36 2 10 Operating System Setup This motherboard supports various Microsoft Windows operating sys tems 8 8 64 bit 7 7 64 bit Vista Vista 64 bit XP XP 64 bit Because motherboard settings and hardware options vary use the setup procedures in this chapter for general reference only Refer your OS docu mentation for more information 37 2 11 Installing Drivers The Support CD that comes with the motherboard contains necessary driv ers and useful utilities that enhance the motherboard s features 2 11 1 Running The Support CD To begin using the support CD insert
29. n will appear and display the system overview MSRock UEFI setup utility Active Page on Entry This allows you to select the default page when entering the UEFI setup utility 41 3 3 OC Tweaker Screen In the OC Tweaker screen you can set up overclocking features ASRock UEFI setup Utity CPU Configuration CPU Ratio Use this to change the ratio value of this motherboard Intel SpeedStep Technology Intel SpeedStep technology is Intel s power saving technology Processors can switch between multiple frequencies and voltage points to enable power saving The default value is Enabled Con figuration options Enabled and Disabled If you install Windows and want to enable this function please set to Enabled This item will be hidden if the current CPU does not support Intel SpeedStep technology j Please note that enabling this function may reduce CPU voltage and lead 4 to system stability or compatibility issues with some power supplies 77 Please set this item to Disabled if above issues occur Long Duration Power Limit Use this to configure long duration power limit in watts The default value is Auto Long Duration Maintained Use this to configure time window which the long duration power is maintained The default value is Auto Short Duration Power Limit 42 Use this to configure short duration power limit in watts The default value is Auto Primary Plane Current Limit Use this to configure th
30. onfigure internet connection settings for Internet Flash User Defaults You are allowed to load and save three user defaults according to your own requirements 62 3 6 Hardware Health Event Monitoring Screen This section allows you to monitor the status of the hardware on your sys tem including the parameters of the CPU temperature motherboard tem perature fan speed and voltage ASRock UEFI setup Utility CPU Fan 1 Setting This allows you to set CPU fan 1 s speed Configuration options Full On and Automatic Mode The default value is Full On Chassis Fan 1 Setting This allows you to set chassis fan 1 s speed Configuration options Full On and Automatic Mode The default value is Full On 63 3 7 Boot Screen This section displays the available devices on your system for you to con figure the boot settings and the boot priority ASRock UEFI setup Utility Fast Boot Fast Boot minimizes your computer s boot time Configuration op tions Disabled Disable Fast Boot Fast When selecting Fast it is not allowed to boot from a USB storage device Ultra Fast There are a few restrictions 1 Only supports Windows 8 UEFI operating system 2 You will not be able to enter BIOS Setup by using the keyboard The only way to enter UEFI Setup is to clear CMOS or run the Re start to utility in windows 3 If you are using an external graphics card the VBIOS must sup port UEFI GOP in orde
31. p state or powered off S5 HDLED Hard Drive Activity LED Connect to the hard drive activity LED on the chassis front panel The LED is on when the hard drive is reading or writing data The front panel design may differ by chassis A front panel module mainly consists of power switch reset switch power LED hard drive activity LED speaker and etc When connecting your chassis front panel module to this header make sure the wire assignments and the pin assignments are matched correctly re The white wires are negative Connect to or GND pins while the colored ones positive System Panel Header 1 BLED 9 PANEL4 see p 13 15 17 No 12 30 2 8 Onboard Headers and Connectors place jumper caps over these headers and connectors Plac ing jumper caps over the headers and connectors will cause permanent damage to the motherboard Onboard headers and connectors are NOT jumpers Do NOT 4 USB 2 0 Headers DUMMY Besides two default USB 2 0 9 pin USB4_5 s i ports on the I O panel there see p 13 15 17 No 20 2 are three USB 2 0 headers USB PWR USB PWR 1 and one USB port on this motherboard Each USB 2 0 header can support two USB 2 0 ports 9 pin 05 6 7 13 15 17 7 USB PWR 4 pin USB8 GND 5VDC 1 see p 13 15 17 No 3 D D USB 3 0 Header kk BB Besides two default USB 3 0 19 pin USB3 0 1
32. p 1 2 Keep the lever positioned at about 135 degrees in order to flip up the load plate Step 2 Insert the 1155 Pin CPU Step 2 1 Hold the CPU by the edge which is marked with a black line Step 2 2 Orient the CPU with the Integrat ed Heat Sink up Locate Pin1 and the two orientation key notches 23 black line orientation key notch alignment key alignment key orientation key notch 1155 Pin Socket 1155 Pin CPU For proper installation please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket Step 2 3 Carefully place the CPU into the socket Step 2 4 Verify that the CPU is within the socket and properly mated to the orient keys Step 3 Close the socket Step 3 1 Flip the load plate onto the IHS Step 3 2 Press down the load lever and secure it with the load plate tab under the retention tab The pro tection cover will automatically come off by itself Please save and replace the cover if the processor is re moved The cover must be placed if you wish to return the motherboard for after service 24 2 2 Installing the CPU Fan and Heatsink This motherboard is equipped with 1155 Pin socket that supports Intel 1155 Pin CPUs Please adopt the type of heatsink and cooling fan com pliant with Intel 1155 Pin CPU to dissipate heat Before you install the heatsink you need to spray thermal interface material between the CPU and the heatsin
33. port Use this to enable or disable BIOS support for security devices 60 3 5 Tool OMG Online Management Guard Administrators are able to establish an internet curfew or restrict internet access at specified times via OMG You may schedule the starting and ending hours of internet access granted to other us ers In order to prevent users from bypassing OMG guest accounts without permission to modify the system time are required Instant Flash Instant Flash is a UEFI flash utility embedded in Flash ROM This convenient UEFI update tool allows you to update the system UEFI without entering operating systems like MS DOS or Windows first Just save the new UEFI file to your USB flash drive floppy disk or hard drive and launch this tool then you can update your UEFI only in a few clicks without preparing an additional floppy diskette or other complicated flash utility Please be noted that the USB flash drive or hard drive must use FAT32 16 12 file system If you execute Instant Flash utility the utility will show the files and their respective information Select the proper UEFI file to update your UEFI and reboot your system after the UEFI update process is completed Internet Flash Internet Flash searches for available UEFI firmware updates from our servers In other words the system can auto detect the latest UEFI from our servers and flash them without entering Windows 61 OS Network Configuration Use this to c
34. r IO Configuration 56 3 4 8 ACPI Configuration eee 57 3 4 9 USB Configuration iicn 59 3 4 10 Trusted 60 TOOL m 61 Hardware Health Event Monitoring Screen 63 Boot Screen iei ie c ee Re ERE FARE E 64 Security Screen men e rec 66 SCHEOM e P 67 1 Introduction Thank you for purchasing ASRock H77TM ITX B75TM ITX H61TM ITX motherboard a reliable motherboard produced under ASRock s consis tently stringent quality control It delivers excellent performance with robust design conforming to ASRock s commitment to quality and endurance In this manual chapter 1 contains the introduction of the motherboard Chapter 2 provides step by step installation instructions Chapter 3 in cludes information about the UEFI Because the motherboard specifications and the BIOS software might be updated the content of this manual will be subject to change without notice In case any modifications of this manual occur the updated version will be available on ASRock s web site You may find the latest VGA cards and CPU support list on ASRock s website as well http www asrock com If you require technical support related to this motherboard please visit our website for specific information about the model you are using www asrock com support in
35. r to boot Boot From Onboard LAN Use this to enable or disable Boot From Onboard LAN Setup Prompt Timeout This shows the number of seconds to wait for the setup activation key Bootup Num Lock If this is set to On it will automatically activate the Numeric Lock 64 after boot up Full Screen Logo Use this item to enable or disable OEM Logo The default value is Enabled AddOn ROM Display Use this option to adjust AddOn ROM Display If you enable the option Full Screen Logo but you want to see the AddOn ROM information when the system boots please select Enabled Con figuration options Enabled and Disabled The default value is Enabled Boot Failure Guard Enable or disable Boot Failure Guard Boot Failure Guard Count Enable or disable Boot Failure Guard Count 65 3 8 Security Screen In this section you may set or change the supervisor user password for the system You may also clear the user password ASRock UEFI setup Secure Boot Use this to enable or disable Secure Boot Control The default value is Disabled 66 3 9 Exit Screen ASRock 5 Save Changes and Exit When you select this option the following message Save configu ration changes and exit setup will pop out Select OK to save changes and exit the UEFI SETUP UTILITY Discard Changes and Exit When you select this option the following message Discard changes and exit setup will pop out Select OK
36. rial SATA2 SATA3 Hard Disks STEP 1 Connect the SATA power cable to the hard disk STEP 2 Connect one end of the SATA data cable to the hard disk TH U STEP 3 Connect the other end of the SATA data cable to the mother board s SATA2 connectors SATA2 SATA3 Connectors SATA 0 see p 13 15 17 No 6 SATA 1 SATA 0 SATA 1 I see p 13 15 17 No 2 28 These two SATA2 SATA3 connectors support SATA data cables for internal stor age devices 2 6 Power Connectors SATA Power Connector Please connect a SATA SATA POW 1 power cable see p 13 15 17 No 10 29 2 7 Installing the System Panel Connect the power switch reset switch and system status indicator on the chassis to this header according to the pin assignments below Note the positive and negative pins before connecting the cables PWRBTN Power Switch Connect to the power switch on the chassis front panel You may configure the way to turn off your system using the power switch RESET Reset Switch Connect to the reset switch on the chassis front panel Press the reset Switch to restart the computer if the computer freezes and fails to perform a normal restart PLED System Power LED Connect to the power status indicator on the chassis front panel The LED is on when the system is operating The LED keeps blinking when the sys tem is in S1 S3 sleep state The LED is off when the system is in S4 slee
37. s been advised of the possibility of such damages arising from any defect or error in the manual or product Fe This device complies with Part 15 of the FCC Rules Operation is subject to the fol lowing two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CALIFORNIA USA ONLY The Lithium battery adopted on this motherboard contains Perchlorate a toxic substance controlled in Perchlorate Best Management Practices BMP regulations passed by the California Legislature When you discard the Lithium battery in Cali fornia USA please follow the related regulations in advance Perchlorate Material special handling may apply see www dtsc ca gov hazardouswaste perchlorate ASRock Website http www asrock com Contents 1 Introduction emere ee hem 5 1 1 Package Contents nones 5 1 2 SpecifiCatlons 5 xmas ce RU etu 6 1 3 Unique Fealtures iret 10 1 4 Motherboard Layout H77M ITX 13 1 5 Motherboard Layout B75M ITX 15 1 6 Motherboard Layout H61M ITX 17 1 7 W O Panel H77M TX iiiter tette 19 1 8 I O Panel B75M ITX sse 20 1 9 I O Panel H61M ITX 21 2 Installation hein 22 2 1 Installing the GP orte 23 2 2
38. state after an unexpected AC power loss If Power Off is selected the AC power remains off 51 when the power recovers If Power On is selected the AC power resumes and the system starts to boot up when the power recov ers Good Night LED Use this to enable or disable the Power LED and LAN LED 52 3 4 4 Storage Configuration SATA Controller s Use this to enable or disable the SATA Controllers SATA Mode Selection Use this to select the SATA mode Configuration options IDE Mode AHCI Mode and RAID Mode The default value is AHCI Mode RAID Mode is for H77M ITX only AHCI Advanced Host Controller Interface supports and other new X features that will improve SATA disk performance but IDE mode does not have these advantages SATA Aggressive Link Power Management Use this to configure Aggressive Link Power Management Hard Disk S M A R T Use this to enable or disable S M A R T Self Monitoring Analysis and Reporting Technology 53 3 4 5 Intel R Rapid Start Technology ASRock 5 T Intel R Rapid Start Technology Use this to enable or disable Intel R Rapid Start Technology Intel R Rapid Start Technology is a new zero power hibernation mode which allows users to resume in just 5 6 seconds The default is Enabled Entry After Select a time to enable RTC wake timer at S3 entry The default is 10 minutes Active Page Threshold Support This allows you to enable
39. the CD into your CD ROM drive The CD automatically displays the Main Menu if AUTORUN is enabled in your computer If the Main Menu does not appear auto matically locate and double click on the file ASRSETUP EXE in the Support CD to display the menu 2 11 2 Drivers Menu The drivers compatible to your system will be auto detected and list ed on the support CD driver page Please follow the order from top to bottom to install those required drivers Therefore the drivers you install can work properly 2 11 3 Utilities Menu The Utilities Menu shows the application softwares that the mother board supports Click on a specific item then follow the installation wizard to install it 2 11 4 Contact Information If you need to contact ASRock or want to know more about ASRock you re welcome to visit ASRock s website at http www asrock com or you may contact your dealer for further information 38 Chapter 3 UEFI SETUP UTILITY 3 1 Introduction This section explains how to use the UEFI SETUP UTILITY to configure your system The UEFI chip on the motherboard stores the UEFI SETUP UTILITY You may run the UEFI SETUP UTILITY when you start up the computer Please press F2 or Del during the Power On Self Test POST to enter the UEFI SETUP UTILITY otherwise POST will continue with its test routines UEFI setup screens and descriptions are for reference purpose only and Because the UEFI software is constantly
40. the notch on the DIMM matches the break on the slot The DIMM only fits in one correct orientation It will cause per j manent damage to the motherboard and the DIMM if you force f the DIMM into the slot at incorrect orientation Step 2 Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated 26 2 4 Expansion Slots PCI Express Slots There is 1 PCI Express slot and 1 mini PCI Express slot on this mother board Mini PCIE Slot MINI PCIE1 is used for mini PCIE cards PCIE slots The x4 lane width PCIE1 PCIE 3 0 x4 slot is used for PCI Express expansion cards Installing an Expansion Card Step 1 Step 2 Step 3 Step 4 Before installing an expansion card please make sure that the power supply is switched off or the power cord is unplugged Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation Remove the bracket facing the slot that you intend to use Keep the screws for later use Align the card connector with the slot and press firmly until the card is completely seated on the slot Fasten the card to the chassis with screws PCIE1 slot supports Gen 3 speed To run PCI Express in Gen 3 speed please install an Ivy Bridge CPU If you install a Sandy Bridge CPU the PCI Express will run only at PCI Express Gen 2 speed 27 2 5 Installing Se
41. to exit the UEFI SETUP UTILITY without saving any changes Discard Changes When you select this option the following message Discard chang es will pop out Select OK to discard all changes Load UEFI Defaults Load UEFI default values for all options The F9 key can be used for this operation Launch EFI Shell from filesystem device Attempt to Launch EFI Shell application Shell64 efi from one of the available filesystem devices 67
42. y with max resolution up to 1920x1200 60Hz Supports DVI I with max resolution up to 1920x1200 75Hz Supports LVDS with max resolution up to 1920x1200 60Hz Supports Auto Lip Sync Deep Color 12bpc xvYCC and HBR High Bit Rate Audio with HDMI Supports HDCP with HDMI Supports Full HD 1080p Blu ray BD HD DVD playback with HDMI Graphics 7 1 CH HD Audio with Content Protection Realtek ALC892 Audio Codec Premium Blu ray audio support PCIE x1 Gigabit LAN 10 100 1000 Mb s 2 x USB 3 0 Ports H61TM ITX by Etron EJ188 2 x USB 2 0 Ports 1 x RJ 45 LAN Port with LED ACT LINK LED and SPEED LED 2 x SATA3 6 0 Gb s connectors support RAID RAID 0 RAID 1 RAID 5 RAID 10 Intel Rapid Storage and Intel Smart Response Technology NCQ AHCI and Hot Plug functions H77TM ITX 1 x SATA3 6 0 Gb s connector and 1 x SATA2 3 0 Gb s con nector support NCQ AHCI and Hot Plug functions B75TM ITX 2 x SATA2 3 0 Gb s connectors support NCQ AHCI and Hot Plug H61TM ITX Connectors 1 x Analog Surround Audio header 1 x Digital MIC header 1 x 3W Audio AMP Output Wafer header 1 x SATA Power connector RTL8111E VL Rear Panel 1 0 3 x USB 2 0 headers support 5 USB 2 0 ports 1 x USB 3 0 header supports 2 USB 3 0 ports H61TM ITX by Etron EJ188 CPU Core IGPU DRAM 1 8V PLL VTT VCCSA Voltage Multi adjustment Drivers Utilities AntiVirus Software Trial Version Cyber
Download Pdf Manuals
Related Search