Home
Agio Sling Swivel-Rocker Assembly Instruction
Contents
1. IMPORTANT PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY TO EXPEDITE ANY FUTURE WARRANTY CLAIMS PLEASE KEEP INSTRUCTION SHEET WARRANTY CARD AND RECEIPT Step 1 Identify all parts packed in carton against the parts list Remove all protective materials Place parts on a non abrasive surface to avoid scratching If you are missing any parts or are unsure as how to proceed with the assembly call our Customer Service Center at 1 800 416 3511 Do not attempt assembly if any parts are missing or damaged Step 2 Place the swivel base with rocker assembly on a flat solid surface Make sure the rocker assembly is positioned all the way into the base It may have shifted or vibrated out during shipment Step 3 Important We recommend 2 people work together to assemble the chair Note the arrow labels on the U bar and the rocker assembly Also note the horseshoe shape of the rocker plate Point the open end of the horseshoe away from you The arrows on the rocker assembly should be pointing towards you Set the chair frame on the rocker assembly with front of the seat facing you and the arrows on the U bar pointing towards you as shown in Figure 1 This is very important for a safe balanced rocking motion If chair frame has been properly positioned on the rocker assembly all arrows on the U bar and rocker assembly will be pointing in the same direction Step 4 Critical Step The U metal plates must be installed in the proper locati
2. cks too far forward to or is difficult to rock backwards you have probably installed the seat frame backwards on the rocker assembly If you need further assistance please call our Customer Service Center at 1 800 416 3511 IMPORTANTNOTE Damage to welds or frames resulting from over tightened bolts or improper assembly is not covered under our warranty Please read all instructions carefully before assembly If you have any questions regarding your assembly call our Customer Service Center at 1 800 416 3511 50 49661 1 NOTE MAKE SURE ARROWS SEAT DESIGNS MAY FROM BOTH THE U BAR VARY BUT THE ASSEMBLY AND ROCKER ASSEMBLY IS THE SAME ARE POINTING IN THE SAME DIRECTION U METAL PLATE y BAR FRP ROCKER Figure 1 ASSEMBLY PVC BOLT COVER y BAR SPRING WASHER Figure amp NUT PARTS LIST DESCRIPTION ORDER PART QTY PARTS LIST DESCRIPTION ORDER PART QTY dd CHAIR FRAME AR1094 1 QD PVCBOLTCOVER HW0028 8 SWIVEL BASE amp PAS ROCKER AR1095 1 HEX WRENCH 1 HW0008 1 ASSEMBLY 5 16 X 40 MM i KOLT HW0295 4 c0 HEX WRENCH 2 HWwo0007 1 08 0 X 2 3 MM gt FRP SPRING WASHER HW0003 4 KZ ractory asseMpty 0009 CS U METAL FOOT CAP na ae PEATE HWw0296 2 at ices FC0004 5 16 NUT HW0015 4 SLING IUBE CAE E0046
3. on Read this step and carefully examine Insert the U metal plate so that the U bar and rocker plate are between both sides of the U metal plate Make sure that the holes in the U metal plate are completely aligned with the holes in the U bar as shown in Figure 1 Guide the bolts through the holes on the top side of the U metal plate through the holes in the U bar portion of the chair through the holes in the rocker plate and then most importantly through the holes in the bottom side of the U metal plate It is very important that the holes in the bottom portion of the U metal plate be placed directly beneath the holes in the rocker plate Add a spring washer and a nut to each bolt as shown in Figure 2 Hand tighten nuts 3 4 revolutions only Repeat the same procedure on the other side CAUTION Failure to place U metal plates under the rocker plates and above the U bar exactly as shown in diagram will cause the bolt heads and nuts to damage the structure of the rocker plates and the U bar Damage due to over tightening of bolts or improper assembly could cause injury and may void your warranty Step 5 Tighten all nuts and bolts with the hex wrenches provided Do not over tighten Remove arrow labels from U bar and rocker assembly Cover bolts with PVC bolt covers Step 6 Your chair should be ready for use If your chair is not rocking properly double check your assembly procedure especially Step 3 If the chair ro
Download Pdf Manuals
Related Search
Related Contents
TM-T20II User`s Manual Manual de funcionamiento telechargez la fiche technique König CMP-COOLER110 notebook cooling pad DES ETUDES A L`EMPLOI - Université Paris 1 Panthéon Zalman GS1000 National Instruments NI PXI-5422 User's Manual TDK NC360 MARINE RADAR BR-3200 Handpräger Bedienungsanleitung Copyright © All rights reserved.
Failed to retrieve file