Admiral Craft SG-811E/F Owner's Manual
Contents
1. SG 811 SG 811 F SG 811E SG 811E F SG 813 Panini Sandwich Grills This manual contains important information regarding your Admiral Craft unit Please read this manual thoroughly prior to equipment set up operation and maintenance Failure to comply with regular maintenance guidelines outlined in this manual may void the warranty MUST READ Instructions For First Time Use of Grills In order to protect the plates of your new grill during transportation a layer of food safe bee s wax was coated on the surface prior to shipment This wax is harmless but must be removed before initial use To remove preheat the grill until the wax liquifies Next carefully wipe away the melted wax with a clean soft cloth Once all of the wax is removed you can begin to use your grill PLEASE NOTE For your convenience the handle on this sandwich panini grill is fully adjustable for your desired tension To adjust the tension open the rear cover see Figure A with a screwdriver to expose the hex screws Using an allen wrench to adjust the screws see Figure B either loosen the handle by adjusting counter clockwise or tighten by adjusting clockwise as this will insure easy and comfortable use of your grill If you hear any sound when you lift or lower the handle lubricate the center hole of copper base see Figure C with lubricating oil Figure A Figure B Figure C WARNINGS Do not touch any hot surfaces2. Warm up time is approximately 7 8 minutes The Heating indicator will cycle at set temperature 4 For normal use it is recommended that the temperature range be 392 F 482 F 5 When the surface reaches the designated temperature lift top grill using black handle and lightly grease grill plates with vegetable oil Place food on grill and lightly press handle down Excess oil will collect in the oil collection tray Remove food when cooked The heaters will automatically cycle as needed CLEANING NOTE To maintain cleanliness and increase service life the grills should be cleaned daily Do not immerse the grill in water or any other liquid 1 Before cleaning or attempting to move grill unplug and let the unit cool completely 2 Wipe the entire unit with a clean soft cloth until it is completely dry 3 To avoid damage do not use abrasive cleaners or scouring pads 4 If soap or chemical cleaners are used be sure they are completely rinsed away with clear water immediately after cleaning Chemical residue could damage or corrode the surfaces of the unit 5 Store in a dry clean area when not in use TROUBLESHOOTING Possible Causes Action 1 Grill plates do not heat 1 Defective even though power controller indicators are lit 2 Defective heater s 1 Replace controller 2 Replace heater s 1 Defective 2 Temperature cannot be 1 Replace temperature temperature controller controller controlled 3 H
3. Do not immerse unit cord or plug in liquid at any time Unplug cord from outlet when not in use and before cleaning Plug only into a 3 hole grounded electrical outlet Do not operate unattended Do not use this unit for anything other than intended use Do not use outdoors Keep children and animals away from unit Always cook on a firm dry and level surface at least 12 from walls or any other obstruction Do not use unit with a damaged cord or plug in the event the appliance malfunctions or has been damaged in any manner Any incorrect installation alterations adjustments and or improper maintenance can lead to property loss and injury All repairs should be done by authorized professionals only Ensure that the power supply you are using is adequate for continual grill usage and the voltage is correct Do not jam materials or place heavy objects on grill as this may cause damage In order to protect the plates of your new grill during transportation a layer of food safe wax was coated on the surface prior to shipment This wax is harmless but must be removed before you begin to use To remove preheat the grill until the wax liquefies Next carefully wipe away the melted wax with a clean soft cloth Once all of the wax is removed you can begin to use your grill TO USE 1 Plug the power cord into the appropriately rated outlet 2 The power light will illuminate 3 Once desired temperature is set the Heating Indicator will come on
4. mim e e prm U io i T 5 2 p nghe Heating yA ji rt Heating element E element AWG 16 AJE dh AWG 164f3 K Or a O gt E I EIL AWG 18 2 4 AWG 18 AC L N 120 1 75kW als AWG 18 Le el L AC L N 120 1 75kW G I 5 L AWG 18 T C n m Ai dl db og V Ye n m bj ki YO di lu mm Ye b hi mad WRH dc dt ETEY Power ser Heating Power ssi Heating light Thermostat light light Thermostat light SG 811 i sal SG8ME be E 25 WLLL VER811 fC SG 813 i m PETT nm A em MM MM 25 i MM EEE VERGI Sandwich Grills SG 811 SG 811 F SG 811E SG 811E F SG 813 Reference SG 811 and SG 811 F SG 811E and SG 811E F Number Part Number Part Number SG 813 Part Number Description 3 m m THi201 thermostat Regulator 3 Deen Dreses DF6S63 Power Indicator Green d TT s ses T es G5 frorsionar Spring w Screws 6 se6 ms es ans 8 sera Im TT S638 wisCwer 9 ses a G9 jWisHodigPn TTT jBettemPlte Casin TT Co TT TT Fo Plate Cover w Screws _ 3 T_T upper Mounting Plate aS T Tep Plate Cast r n TT TT omn Tower Mounting Plate TT Ca o SoSo i oOo o o me 28 TT BettemCoverw Serews OO VER811 ACE Electrical Equipment One Year Warranty ACE warrants its equipment against defects in materials and workmanship subject to the following conditions This warranty applies to the original owner only and is no
5. eating indicator appears normal but power indicators are not lit 1 Defective power 1 Replace power indicator s indicator s Grill SG 811EB Circuit diagram AWG 16k Je Bret OE mE E AWG14 494 Power cord BEH O Ox AC L N 120 1 75kW AWG 164 JE Terminal Heating e ad 4 mi OF gt rd e EI e dil di e Heating 3 2 FERL OAW 3 element z AWG 169kpE 9 CL gt bh gf AWG 18 2 GT 1 AWG 18 i II Il N H Ti H Gr OO Bin IB ad Jh etj inti JE ae Power Heatin light TUE kai P Thermostat AC 120V 1 75kW rp ST Thermostat Heating light Ene Heating element Heating element Grill SG 811B Circuit diagram L AC 120V 1 75kW HL1 Pawer light EH Heating Heating element element N ER AWG 1 66 MI RE di 514 AL AWG 4 Hdi Power cord li i 0 A LU mi mm OF AC L N 120 1 75kW AWG 1 CE Terminal Heating element 81 OAV Heating 2 uu element 3 AWG 168kii3 Of ib e ii u AT Power s Heating light EZ light Thermostat Grill SG 813B Circuit diagram AWG 1 DRK JEU S fa AWG 14 99 SW Powercord Heating L Heating a element E element AWG 1685 IEIRA AWG IA iplo e Power cord E C Li WI AWG 16 8k y AWG TERRE Terminal e 2 ha 4 B ili dka Heating e DE 3 w denen Che x O El z E m E m
6. quipment that has not been used in an appropriate manner or has been subject to misuse neglect abuse accident alteration negligence damage during transit delivery or installation fire flood riot or act of God e Equipment that has the model number or serial number removed or altered e Equipment on which the security seal has been broken If the equipment has been changed altered modified or repaired without express written permission from ACE then the manufacturer shall not be liable for any damages to any person or to any property which may result from the use of this equipment thereafter This equipment is intended for commercial use only Warranty is void if equipment is used in other than a commercial application In the event your repair is not covered under the stated warranty provisions parts are available by calling 1 800 223 7750 Equipment not covered by repair should be picked up from our warehouse facility within 10 business days from notification date Any and all arrangements and expenses for the return of this merchandise is your responsibility THE FOREGOING WARRANTY IS IN LIEU OF ANY AND ALL WARRANTIES EXPRESSED OR IMPLIED INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILTY OR FITNESS FOR PARTICULAR PURPOSES AND CONSTITUES THE ENTIRE LIABILITY OF ACE IN NO EVENT DOES THE LIMITED WARRANTY EXTEND BEYOND THE TERMS STATED HEREIN VER401 11
7. t assignable ACE Electrical Equipment is warranted for one year effective from the date of purchase by the original owner A copy of the original receipt or other proof of purchase is required to obtain warranty coverage Should any product fail to function in its intended manner under normal use within the limits defined in this warranty at ACE s discretion such product will be repaired replaced with a refurbished unit or replaced with a new unit by ACE after defective unit has been inspected and defect has been confirmed ACE does not assume any liability for extended delays in replacing any item beyond its control This warranty does not apply to rubber and non metallic synthetic parts where usage wear or lack of preventative maintenance may create abnormal replacement rates and these parts are excluded from this limited warranty This warranty covers products shipped into the 48 contiguous United States Hawaii and metropolitan areas of Alaska and Canada Warranty coverage on products used outside the 48 contiguous United States Hawaii and metropolitan areas of Alaska and Canada may vary Contact ACE for details at 1 800 223 7750 The following conditions are not covered by watranty e Equipment failure relating to improper installation improper utility connection or supply and problems due to improper ventilation e Equipment that has not properly been maintained damage for improper cleaning and water damage to controls e E
Download Pdf Manuals
Related Search