User's Guide Carbon Monoxide Meter Model CO10
Contents
1. freight insurance and proper packaging to prevent damage in transit This warranty does not apply to defects resulting from action of the user such as misuse improper wiring operation outside of specification improper maintenance or repair or unauthorized modification Extech specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and will not be liable for any direct indirect incidental or consequential damages Extech s total liability is limited to repair or replacement of the product The warranty set forth above is inclusive and no other warranty whether written or oral is expressed or implied Calibration and Repair Services Extech offers repair and calibration services for the products we sell Extech also provides NIST certification for most products Call the Customer Service Department for information on calibration services available for this product Extech recommends that annual calibrations be performed to verify meter performance and accuracy qircoencern Extech CO10 Phone 01235 838 555 E mail cs airconcern co uk web www airconcern co uk2. User s Guide EXTECH INSTRUMENTS Carbon Monoxide Meter Model CO10 EXTECH INSTRUMENTS Introduction Congratulations on your purchase of the Extech C010 Carbon Monoxide Meter The COQ10 measures and displays CO concentrations between 0 and 1000 parts per million ppm Safety Information Carbon monoxide is life threatening even at relatively low concentrations learn and recognize the effects of CO poisoning see Table below Do not use this meter as a personal safety monitoring device Effects of CO poisoning 1600 PPM Nausea within 20 minutes DEATH WITHIN 1 HOUR 12800 PPM DEATH WITHIN 2 TO 3 MINUTES Ensure that the meter is turned on in an area free of CO If not the meter will read incorrectly when subsequently measuring CO Meter Description 1 LCD display 2 Power ON OFF key 3 MODE key 4 Power on Alarm light 5 SEL key 1 6 Sensor vg Battery compartment N Fo wo 2 C010 V2 0 10 05 Operation MEASUREMENTS IMPORTANT Ensure that the meter is turned on in an area free of CO If not the meter will read incorrectly when subsequently measuring CO 1 Press the ON OFF button to turn the meter on Allow time for the meter to perform the self test and for the display to settle co To use the meter trace the CO10 around the area of the l suspected leak h The meter will indicate the presence of CO in ppm on the LCD display An audible beep
3. fter 15 minutes of inactivity Audible Alarm Enable Disable The audible alarm can be turned on off by pressing the SEL button on or off will be on displayed on the LCD The alarm light will remain enabled in either setting Backlight In the measure mode press and hold the SEL button for 4 seconds to turn the backlight on off Press the MODE button to enter maximum data mode 3 C010 V2 0 10 05 Specifications Measurement range 0 1000 ppm Resolution 1 ppm Accuracy 5 or 10 ppm whichever is greater Sensor Type Stabilized electrochemical Gas specific CO Sensor Life Typical 3 years Warm up Period lt 2 seconds Power supply 9V Battery NEDA 1604 or IEC6F22 Battery life Approx 50 hours with alkaline battery Operating Temperature 32 to 122 F 0 to 50 C Storage Temperature 22 to 140 F 30 to 60 C Operating Humidity 0 to 99 RH non condensing Dimensions 6 3 x 2 2 x 1 57 160 x 56 x 40mm Weight 6 350z 180g Warranty EXTECH INSTRUMENTS CORPORATION warrants the basic instrument to be free of defects in parts and workmanship for one year from date of shipment a six month limited warranty applies on sensors and cables If it should become necessary to return the instrument for service during or beyond the warranty period contact the Customer Service Department at 781 890 7440 EXTENSION 210 for authorization or visit www extech com for more information The sender is responsible for shipping charges
4. will sound at 35 ppm alerting the user that the threshold of dangerous CO levels has been detected The higher the concentration of CO the faster the beeper will sound Above 200PPM the beeper will sound continuously To turn the meter off press the ON OFF key If the meter is left on the meter will automatically power off after 15 minutes MODE Button Functions Press the MODE button to step through the following functions 1 Maximum Data Mode Displays the highest reading taken This reading is cleared when the meter is powered off Recall Data Mode Press the SEL button to step through and recall the data from the 10 memory locations The current memory location 0 9 is displayed in the top right Store Data Mode In this mode you can store the reading to the next available memory location by pressing the SEL button REC is displayed in the top right Recall Alarm Mode The meter will display the alarm level data setting 30ppm Zero Mode Press the SEL button for over 8 seconds to enter the manual zero adjusting mode The zero value will blink and F then the display will 0 and the meter will return to the jci Measure Mode Measuring Time Mode Auto Power Off disable This mode will display how long the meter has been on taking measurements The time is cleared when the meter is powered off The auto power off function is disabled in this mode In all other modes auto power off is enabled and will power off a
Download Pdf Manuals
Related Search