Belle - Maxitile 260 - Electric Tile Cutter
Contents
1. Adjust the blade to the 45 position with the inclination adjustment knobs See picture 6b Lock the motor carriage at the max cutting depth with the locking lever Picture 6c shows cl the proper way the machine should be used In order to carry out special working it is possible to set out any cutting inclination ranging from 0 to 45 as marked on the machine side See picture 6d Before any cutting make sure that the Tile to be cut is proper AN CAUTION ee APCE up against The tile stop a With the MAXITILE machine it is also possible to set out a the cutting length with the cutting adjustment knobs b the cutting depth with the locking lever c the straight cut measurement with the tile bearing square as well as the ruler placed on the working table d the cutting adjustment with the specially provided indicator and ruler placed on the slide rail Maintenance Before performing any maintenance operation ensure the machine is disconnected from the power AN CAUTION P g any P P supply MINITILE amp MAGIKTILE ONLY DIAMOND BLADE DISASSEMBLY Remove the blade guard Use the 4mm Allen Key to hold the motor shaft Unscrew the blade flange block nut with the 19mm spanner After removing the blade clean the blade flange thoroughly and check for wear Lubricate surfaces with fine oil then fit new blade MAXITILE ONLY After dismantling the blade clean the blade flanges carefully and c2. Belle Group and or their recognised agents directors employees or insurers will not be held liable for consequential or other damages losses or expenses in connection with or by reason of or the inability to use the machine for any purpose Warranty Claims All warranty claims should firstly be directed to Belle Group either by telephone by Fax by Email or in writing For warranty claims Belle Group Warranty Department Unit 5 Bode Business Park Ball Haye Green Leek Staffordshire ST13 6BW England Tel 44 0 1538 380000 Fax 44 0 1538 380038 Email warranty belle group co uk 11 Belle Group Head Office Sheen nr Buxton Derbyshire SK17 OEU GB Tel 44 0 1298 84000 Fax 44 0 1298 84722 email sales belle group co uk Belle Group France 70 av du G n ral de Gaulle 94022 Creteil Cedex FRANCE Tel 33 0 1 49 81 68 32 Fax 33 0 1 43 39 94 40 Ventes 0800 902 461 SAV 0800 905 336 SAV Fax 0800 909 895 Belle Equipos SL Calle Doctor Calero Cial 19 Local 22 28220 Majadahonda Madrid Spain Tel 34 0 91 636 2043 Fax 34 0 91 634 1535 email belleequipos belleequipos com Belle Group Deutschland Husumer Stra e 45 a Belle Poland sp z 0 0 96 200 Rawa Mazowiecka Ul Mszczonowska 36 Polska Tel 48 0 46 8144091 Fax 48 0 46 8144700 Belle Group Portugal Rua Laura Alves 225 2 F 2 75 116 Parede Portugal Tel 35 1 21 453 59 91 Fax 35 1 2
3. 1 453 59 91 Belle Group Netherlands Tel 0800 249861 Belle Group Belguim Tel 0800 80295 Belle Group Austria Tel 0800 291544 Belle Group Russia 64 Nevsky pr St Petersburg Russia No 1 for Light Construction Equipment wl www BelleGroup com Belle Group GB Shanghai Office Room 213 Zhonghuang Building 1007 Zhongshan Nan Er Road Xuhui Shanghai 200030 China Tel 00 86 21 5461 5228 Mobile 00 86 133 8172 2653 Fax 00 86 21 5461 5369 email morgan liu bellegroup com cn Belle Group Inc 3959 Electric Rd Roanoake Suite 360 VA 24018 USA Tel 1 540 345 5090 Fax 1 540 345 5091 Toll free 866 540 5090 e mail sales bellegroup net a Parts Belle Group World Parts Centre D 33729 Tel 7 812 314 81 34 Unit 5 Bode Business Park Bielefield Moscow 7 495 589 64 32 Ball Haye Green Deutschland Leek Tel 49 0 5217 707505 Belle Group South East Asia Staffordshire Fax 49 0 5217 707506 21 Jalan Ara AD 7 3B ST13 8BW Sales 0800 1808069 Spares 0800 1816673 www BelleGroup com Pandar Sri Damansara S2200 Kuala Lumpar Malaysia Tel 60 0 3 62721678 60 0 3 6272 9308 Fax 60 0 3 6272 9528 Tel 44 1538 380000 Fax 44 1538 380038 OPK NN ZR ERA AP LED MIXING CONCRETING CUTTING BREAKING MOVING COMPACTING
4. 5 Position the tilting table as shown in figure 5b then lock it in place with the knobs Position the cutting guide approx 2 mm from the diamond blade then lock it in place by tightening the knobs fully Position the tile with the enamel surface downwards make sure that the diamond blade does not come into contact with the tile enamel Adjust the position of the cutting guide as necessary Figure 5b illustrates the correct position of the hands in the case of 45 angle cuts Note that the right hand holds the piece in contact with the diamond blade while the left hand moves the piece forward The forward movement of the piece must be proportional to the blade cutting capacity to prevent hazardous fragments which would involve accidentsor injuries from breaking off MAXITILE ONLY Cutting at 90 Thanks to the great versatility of the MAXITILE machine it is possible to carry out different types of cutting Adjust the blade to the 0 position with the inclination adjustment knobs See picture 6a Position the piece which needs cutting on the working table and make sure that it is properly up against the tile stop If necessary a square can be of help In order to carry out any diagonal cutting lean the tile against the square the way it is shown in picture 6b and go on with the cutting operation The millimetre ruler placed on the Working table helps only for JD CAUTION near Cuting Cutting at 45
5. IS DESIGNED FOR WORKING WITH WATER Before and during cutting operations make sure that the water level is sufficient to cover the diamond part of the blade Fill or top up the basin directly as shown in the picture 1a In particular cases it may be necessary to use a tray to recover the cooling water If so use a tray with the following dimensions MINITILE 180 L50 cm P 60 cm H 10 cm MINITILE 200 L 50 cm P 60 cm H 10 cm MINITILE 230 L 60 cm P 60 cm H 10 cm MAGIKTILE 180 L 50 cm P 60 cm H 10 cm THE MAXITILE MACHINE IS DESIGNED FOR WORKING WITH WATER Before any cutting operation make sure that the water level inside the basin is the same as the one shown in picture 1b Through an on off valve it is possible to adjust the water flow according to the type of material to be cut An innovative cooling system makes it possible and allows the disk to be always wet Adjusting The Blade Guard for operator safety if unintentionally touched pay particular attention to avoid contact between your fingers The machine is equipped with a continuous diamond rim blade Even though this blade has been designed AN CAUTION and the blade during operation of the machine MINITILE amp MAGIKTILE ON d Position the blade guard approximately half a centimetre above the tile surface Lock the blade guard in position by fully tightening the screw illustrated in the figure Installation MAXITILE ONLY Remove th
6. Operators Manual Us Operators Manual F Manuel De L Op rateur CE Manual del Operador Spare Parts Book Pieces detachees Libro Despiece 870 30006 0 Health and Safety PPE Personal Protective Equipment Suitable PPE must be worn when using this equipment i e Safety Goggles Gloves Ear Defenders Dust Mask and Steel Toe capped footwear Wear clothing suitable for the work you are doing Tie back long hair and remove any jewellery which may catch in the equipment s moving parts Dust The sawing process will occasionally produce dust which may be hazardous to your health Always wear a mask that is suited to the type of dust being produced Connecting To The Power Supply The machine is to be connected to the mains by a residual current circuit breaker RCCB or class Il isolation transformer with the following characteristics MINITILE 180 RCCB 230V In 3A Id 20 mA 115V In 6 Id 20 mA TRANSFORMER 230V 50 Hz 650 W 115V 50 Hz 650 W MINITILE 200 RCCB 230V 5 Id 20 mA 115V 6 Id 20 mA TRANSFORMER 230V 50 Hz 650 W 115V 50 Hz 650 W MINITILE 230 RCCB 230V 10 Ald 20 mA 115V 16 Ald 20 mA TRANSFORMER 230V 50 Hz 1500 W 115V 50 Hz 1500 W MAGIKTILE 180 RCCB 230V In 6 A Id 20 mA 115V In 3 A Id 20 mA TRANSFORMER 230V 50 Hz 650 W 115V 50 Hz 650 W MAXITILE 260 RCCB 230V In 5A Id 20 mA 115V In 10 A Id 20 mA TRANSFORMER 230V 50 Hz 1000 W 115V 50 Hz 1000 W Pre Start Checks THE MINITILE MAGIKTILE MACHINE
7. e machine from the packaging with the aid of the side carrying handles To set up the machine for work proceed as follows 1 Remove the leg lock pin and raise the rear side pump side of the machine with the handle until the leg is fully extended See picture 3a 2 Raise the leg by sliding it inside the slot 3 Repeat the operation for the front side of the machine See picture 3b 4 Insert the tube holder rod in its seat See picture 3c Transportation MAXITILE ONLY The MAXITILE machine is easy to carry by using the specially provided side handles See picture 4 Before carrying the machine make sure that e the motor slide is locked in place with the two cutting adjustment knobs on the slide rail e the motor slide is completely lowered and locked with the locking lever e the machine is in the 45 jolly position and that the inclination adjustment knobs are properly tightened the tube holder rod is out of its housing the feet are closed and the leg lock pin inserted Operating Instructions MINITILE amp MAGIKTILE ONLY Cutting at 90 Position the cutting guide and lock it by tightening the knobs fully See Figure 5a The picture on the right shows how to position hands correctlyduring cutting at 90 The forward movement of the piece must be proportional to the blade cutting capacity to prevent hazardous fragments that would involve accidents or injuries from breaking off Cutting a surface at 4
8. heck them for wear Grease any surface with fine oil and go on with the assembly of a new blade Check for correct direction of rotation as clearly indicated on the blade MOTOR CARRIAGE ADJUSTMENT The motor carriage is provided with a register for the vertical play adjustment If any excessive play of the motor carriage should take place act as follows 1 Loosen the register fixing nut with a 10mm spanner 2 Screw down the dowel with a 4 mm Allen Key until the play is eliminated 3 Lock the register again with the fixing nut CLEANING It is extremely easy to clean the MAXITILE machine by loosening the side knobs and dismantling the working table Through the side drain remove any residue See picture 7d When necessary clean the sprayer as shown in pictures 7e and 7f 10 Troubleshooting Guide HAVE YOUR MACHINE REPAIRED BY A QUALIFIED PERSON ONLY This electric machine complies with the relevant safety rules Repairs should only be carried out by qualified persons using original spare parts otherwise this may result in considerable danger to the user Fault Cause Remedy The machine does not function The power supply cable is damaged or not properly connected Press the plug firmly into the power socket No voltage in the socket Have the socket checked Switch is damaged Consult local dealer Diamond blade is bent due to incorrect use Replace diamond blade If
9. lubrication does not arrive at the blade with the The sprayer unit is clogged pump running Dismantle the sprayer assembled inside the blade cover and remove any possible residuals Motor gives off unpleasant Water may have seeped through inside odour the motor Unplug the power supply cable and consult local dealer Capacitor is damaged Unplug the power supply cable and consult local dealer Machine is difficult to start Motor bearings are damaged Warranty Consult local dealer Your new Belle Group Tile Saw is warranted to the original purchaser for a period of one year 12 months from the original date of purchase The Belle Group warranty is against defects in design materials an workmanship The following are not covered under the Belle Group warranty 1 Damage caused by abuse misuse dropping or other similar damage caused by or as a result of failure to follow assembly operation or user maintenance instructions 2 Alterations additions or repairs carried out by persons other than Belle Group or their recognised agents 3 Transportation or shipment costs to and from Belle Group or their recognised agents for repair or assessment against a warranty claim on any machine 4 Materials and or labour costs to renew repair or replace components due to fair wear and tear The following components are not covered by warranty e Drive belt s e Engine air filter e Engine spark plug
Download Pdf Manuals
Related Search