THE USER'S GUIDE TO CELCURE® AC
Contents
1. retreated with a cut end preservative Failure to do this will reduce the effectiveness of the preservative It is recommended that the re preserved ends are not put in the ground or in direct contact with water Rip sawing thicknessing and planing are not permitted unless the timber is subsequently re preserved to the original specification Metal Fastenings and Hardware Certain metal products including fasteners hardware and flashing may corrode when in direct contact with wood treated with copper based preservatives To prevent premature corrosion and failure it is important to follow the recommendations of the manufacturer for all metal products Do not use preserved wood in direct contact with aluminium IS96 0813 OSMOSE inser rechnotocies www osmose europe com FM 01724 FM 36409 Colour Celcure AC 10 preserved wood will initially have an even green appearance this will weather to a natural honey brown colour before finally fading to a driftwood grey after long term exposure to the sun Timber treated with Celbronze dyes will have a brown appearance Installation In decking and as a general rule nail boards bark side up annual rings are upward to reduce splitting however the best face should be placed up when a defect of the wood is apparent Fasten thin boards to thicker boards to maintain structural integrity It is a good idea to drill pilot holes for your fixings when screwing near the edge or end of a board2. SEE d Osmose Information THE USER S GUIDE TO CELCURE AC 10 PRESERVED WOOD What is Celcure AC 10 Preserved Wood Celcure AC 10 preserved wood has been preserved by the correct application of Celcure AC 10 wood preservative and then allowed to dry Properly treated Celcure AC 10 preserved wood is protected against attack by wood decaying fungi and wood destroying insects Celcure AC 10 preserved wood treated to an appropriate specification can be used for structural timber sole plates garden furniture playground equipment patios decks fencing garden edging and landscaping structures such as pergolas IMPORTANT INFORMATION Wear gloves when working with wood Only preserved wood that is visibly clean and free of surface residue should be used Wear a dust mask and goggles when cuiting or sanding wood Some preservative may migrate from the treated wood into soil water or may dislodge from the treated wood surface upon contact with skin Wash exposed skin areas thoroughly All sawdust and construction debris should be cleaned up and disposed of after construction Wash work clothes separately from other household clothing before re use If you desire to apply a paint stain clear water repellent or other finish to your preservative treated wood we recommend following the manufacturer s instructions and label of the finishing product Before you start we recommend that you apply the finishing product to a small test area befo
3. This will minimise splitting If the wood has become wet by exposure to rain butt decking boards together during construction As drying occurs some shrinkage can be expected If the wood is dry space the boards to allow for expansion in wet weather Gluing Celcure AC 10 preserved wood can be glued with most commonly used adhesives once dry Always follow the adhesive manufacturer s recommendations Disposal Celcure AC 10 preserved wood that is no longer usable such as off cuts broken boards sawdust or preserved wood material taken out of service may be disposed of in landfills or burned in commercial or industrial incinerators or boilers in accordance with national and local regulations For up to date information please contact the Technical Services Department Biocidal Product Regulation EU 528 2012 Article 58 Information Celcure AC 10 preserved wood is a treated article which incorporates biocidal products Wood correctly preserved with Celcure AC 10 is protected against wood destroying insects and wood rotting fungi Contains Basic copper carbonate Copper Il carbonate Copper II hydroxide 1 1 Benzalkonium chloride Propiconazole Tebuconazole ADDITIONAL INFORMATION Celcure AC 10 preserved wood products are produced by independently owned and operated wood preserving facilities Osmose provides a range of products and technologies for the treatment protection and enhancement of timber Information and advic
4. e is available on all aspects of our products from the Technical Services Department For more information visit www osmose europe com Telephone 44 0 1628 486644 Emergency 44 0 1628 890907 Osmose Protim Celcure and Celbronze are registered trademarks of Protim Solignum Ltd Protim Solignum Ltd trades as Osmose An Osmose company IS96 August 2013 Protim Solignum Ltd Fieldhouse Lane Marlow Bucks SL7 1LS UK Tel 00 44 0 1628 486644 Fax 00 44 0 1628 476757 www osmose europe com email info osmose co uk Registered in England 3037845 Registered Office Fieldhouse Lane Marlow Bucks SL7 1LS UK POO S Protim Solignum Limited s products are sold subject to its standard Terms and Conditions of Sale copies of which may be obtained on request Whilst Protim Solignum endeavours to ensure that any advice recommendation specification or information it may w give is accurate and correct it cannot because it has no direct or continuous control over where or how its products are applied accept any liability either directly or indirectly arising from the use of its products whether or not in accordance with any advice specification recommendation or information given by it save as specifically provided by its Terms and Conditions of Sale
5. re finishing the entire project to ensure that it provides the intended result If the wood is to be used in an interior application and becomes wet during construction it should be allowed to dry before being covered or enclosed Mould growth can and does occur on the surface of many products including treated or untreated wood during prolonged surface exposure to excessive moisture conditions To remove mould from treated wood surfaces wood should be allowed to dry Typically mild soap and water can be used to remove remaining surface mould Preserved wood should not be used where it may come into direct or indirect contact with drinking water except for uses involving incidental contact such as fresh water docks and bridges Do not use preserved wood under circumstances where the preservative may become a component of food animal feed or beehives Do not use preserved wood as mulch Do not burn preserved wood see Disposal All sawdust and construction debris should be cleaned up and disposed of after construction Effective Use of Preserved Wood Cutting Preserved wood should not be cut or otherwise reworked as this will expose unpreserved wood If cutting cannot be avoided then precautions should be taken to keep airborne dust levels below the Workplace Exposure Limits for wood dust In particular avoid inhalation of dust when using high speed cross cut saws or mechanical sanders Any surface exposed by drilling or cutting must be
Download Pdf Manuals
Related Search