Owners Manual - CML Distribution
Contents
1. stationary objects waves wakes and other rapidly moving water wildlife floating debris or overhanging trees You should also be careful to avoid boating in areas where there are many people such as swimming areas park waterways or fishing areas Consult local laws and ordinances before choosing a location to pilot your boat Maximum speeds are only achieved when the water conditions are smooth and there is little wind A sharp turn wind or waves can turn over a boat when it is moving quickly Always pilot your boat for the wind and water conditions so that the boat does not turn over When running your boat for the first time we recommend calm wind and water conditions so that you can learn how the boat responds to your control When making turns decrease the throttle position in order to decrease speed and probability of flipping the boat over Never operate your boat in less than 3 inches 8 cm of water NOTICE When running at full speed in choppy waters the prop may exit and re enter the water repeatedly and very quickly subjecting the propeller to some stress Frequent stress may damage the propeller CAUTION Do not operate this product in vinyl covered or inflatable pools Sharp components may cause damage to these materials CAUTION Never retrieve your boat from the water in extreme temperatures turbulence or without supervision 6 11 TUMBLER Auto roll pool racer Motor Care Prolong motor life by preve2. TUMBLER Auto roll pool racer 4 Apply thread lock to the coupling setscrew Thread lock will help prevent the shaft from loosening during use 5 Carefully reinstall the drive shaft ensuring that there is a 1 2mm gap between the prop strut and the drive dog to allow for shaft shrinkage under load NOTICE Running the boat in salt water could cause some parts to corrode If you run the boat in salt water rinse it thoroughly in fresh water after each use and lubricate the drive system NOTICE Because of its corrosive effects running RC boats in saltwater is at the discretion of the modeler Check Lists Before Boating Install fully charged batteries in your boat and transmitter Connect the boat s battery to the ESC Make sure the boat is bound to the transmitter otherwise bind the boat to the transmitter using the included binding instructions Make sure all linkages move freely on the boat Ensure the motor mount is secured to the hull so that the motor does not move Perform a Control Direction Test with the transmitter Adjust the steering rate on your transmitter as desired Find a safe and open boating area Plan a safe boating route for the water and wind conditions After Boating Always power off the receiver before powering off the transmitter to maintain control of the boat and to retain transmitter binding Disconnect the battery from the receiver and remove the batteries from the boat Fully dry the inside and out
3. last use Boat Battery pack Installation Rotate the hatch on the hull cover in clockwise to unlock the hatch Open the hull cover Adhere loop tape included to the battery Secure the boat battery on the hook strip in the boat Secure the battery in the hull with the hook and loop strap as shown aS 0 N 4 11 TUMBLER Auto roll pool racer Getting Started 1 Power on the transmitter Before open the transmitter pls make sure the Throttle Stick is on the bottom position 2 Connect the battery Use the VELCRO insert the boat to stick the Battery and make sure it will not move by itself 3 Test the transmitter s control of the boat with the boat on the display stand Make sure the propeller running counterclockwise while you face the stern 4 After launching the boat in the water start driving slowly If the boat does not go straight adjust the trimer on the transmitter to run it straight Checking the Radio System 1 Turn the transmitter throttle and rudder trim to the middle position 2 Power on the transmitter 3 Connect a fully charged battery to the ESC CAUTION Always keep all body parts hair and dangling or loose items away from a spinning propeller as these could become entangled NOTICE Always power on the transmitter before powering on the ESC Always power off the ESC before powering off the transmitter Never t
4. VOLANTEX Rc T LIL E Owners Manual _ er NIGH SPEED 5 RACER 796 1 SSS eo Tumbler Auto roll from upside down Specifications Length 260mm Width 100mm Motor 370A brushed motor ESC Advanced micro Receiver amp ESC 2 in 1 Radio 2 4GHz advanced radio control system Read the ENTIRE instruction manual to become familiar with the features of the product before operating Failure to operate the product correctly can result in damage to the product personal property and cause serious injury This is a sophisticated hobby product and NOT a toy It must be operated with caution and common sense and requires some basic mechanical ability Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property This product is not intended for use by children without direct adult supervision Do not attempt to disassemble use with incompatible components or augment product in any way without the approval of VolantexRC Co Ltd This manual contains instructions for safety operation and maintenance It is essential to read and follow all the instructions and warnings in the manual prior to assembly setup or use in order to operate correctly and avoid damage or serious injury Safety Precautions As the user of this product you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the produ
5. ct or the property of others Never attempt to swim after a stalled RC boat Never operate your RC boat while standing in the water Never operate your RC boat in the presence of swimmers NOTE Because of the sharp running hardware included with this RC boat We do not recommend a rubber blow up raft RC boat running hardware is very sharp Be very careful when working on and around the metal parts While the motor is running pay close attention to the propeller Do not come in contact with the propeller at any time the engine is running or serious injury will result Always keep a safe distance in all directions around your model to avoid collisions or injury This model is controlled by a radio signal subject to interference from many sources outside your control Interference can cause momentary loss of control Always avoid water exposure to all equipment not specifically designed and protected for this purpose Moisture causes damage to unprotected electronics Always keep all chemicals small parts and anything electrical out of the reach of children Never place any portion of the model in your mouth as it could cause serious injury or even death Age Recommendation Not for children under 14 years This is not a toy 2 11 TUMBLER Auto roll pool racer Battery Safety Precautions IMPORTANT NOTE Lithium Polymer LiPo batteries are significantly more volatile than the alkaline NiCd and NiMH batteries also used i
6. ell 2S 7 4V LiPo battery used to power the plane you will not want to allow the battery to fall below 6 0V during flight The included ESC features a soft low voltage cutoff LVC that smoothly reduces power to the motor regardless of the power level you have set with the throttle stick to let you know the voltage of the battery is close to the 6 0V minimum 3 11 TUMBLER Auto roll pool racer However even before this reduction in power if you find that more than the typical amount of throttle power is required to power up you should return the model and disconnect the battery immediately to prevent over discharge And while it is possible to continue running the model after the soft LVC occurs this is NOT recommended Continued discharging can result in reaching the 5 0V hard LVC which may cause permanent damage to the LiPo battery resulting in reduced power and running duration during subsequent running or failure of the battery entirely which is not covered under warranty Also it is not recommended that you run to the soft LVC every time you run Instead you should be aware of the power level of the battery through out and if at any time the model begins to require more throttle power than typical to maintain speed you should let the model return back and disconnect the LiPo battery immediately Constantly discharging the battery to the soft LVC can still cause permanent damage to the battery so it s best to use a t
7. imer or stop watch to time the duration of your running and to stop at a reasonable time before the soft LVC is reached IMPORTANT NOTE DO NOT LEAVE THE LIPO BATTERY CONNECTED TO THE ESC UNLESS YOU ARE READY TO RUN IF THE BATTERY IS LEFT CONNECTED TO THE ESC WHEN IT IS NOT IN USE THE LIPO BATTERY WILL BE OVER DISCHARGED BY THE SMALL AMOUNT OF CURRENT THE ESC CONSUMES It can sometimes take a few hours or even up to a few days to over discharge the battery this way but doing so will likely cause permanent damage to or failure of the battery entirely which is not covered under warranty IMPORTANT NOTE DO NOT STORE THE LIPO FLIGHT BATTERY FULLY CHARGED For improved safety and longevity of the LiPo battery it s best to store it only partially charged for any length of time Storing the LiPo battery at approximately 50 charged which is approximately 3 85V per cell is typically best however it will take some careful management of the charge time and the use of a voltmeter to achieve this voltage If you have the equipment and skills to achieve the 50 charge level for storage it is recommended If not simply be sure to not store the battery fully charged whenever possible In fact as long as the battery will be stored at approximately room temperature and for no more than a few weeks before the next use it may be best to store the battery in the discharged state after the last use as long as the battery was not over discharged on the
8. l Repair rudder or adjust rudder and _ rudder trim for straight running when control is at neutral Rudder or rudder trim is not centered Replace or repair damaged parts and Rudder linkage or servo damage adjust controls Replace or repair damaged parts and Rudder linkage or servo damage adjust controls Wire is damaged or connections Do a check of wires and connections are loose connect or replace as needed BEC Battery Elimination Circuit of the ESC is damaged Replace ESC ESC switch is off Power on ESC switch Do the Control Direction Test and Transmitter settings are reversed adjust controls on transmitter appropriately Blocked water cooler tubes Clean or replace water tubes ESC uses default soft Low Recharge boat battery or replace Voltage Cut off LVC battery that is no longer performing Weather conditions might be too Postpone until weather is warmer Battery is old worn out or Battery C rating might be too small Use recommended battery TUMBLER Auto roll pool racer VOLANTE RC 2013 VolantexRC Co Ltd 11 11 TUMBLER Auto roll pool racer
9. n RC applications All instructions and warnings must be followed exactly to prevent property damage and or personal injury as mishandling of LiPo batteries can result in fire By handling charging or using the included LiPo battery you assume all risks associated with LiPo batteries If you do not agree with these conditions please return your complete product in new unused condition to the place of purchase immediately You must read the following safety instructions and warnings before handling charging or using the LiPo battery You must charge the LiPo battery in a safe area away from flammable materials Never charge the LiPo battery unattended at any time When charging the battery you should always remain in constant observation to monitor the charging process and react immediately to any potential problems that may occur After discharging the battery you must allow it to cool to ambient room temperature before recharging Also it is NOT necessary or recommended to discharge the battery completely before charging LiPo batteries have no memory and it s safe to charge partially discharged batteries when using an appropriate charger and settings To charge the battery you must use only the stock included Charger or a suitably compatible LiPo battery charger Failure to do so may result in a fire causing property damage and or personal injury DO NOT use a NiCd or NiMH charger to charge Li Po battery If at any time du
10. near boat during connecting process 3 Reverse throttle channel on transmitter Replace boat battery and follow battery instructions Disassemble lubricate and correctly align parts Make sure battery is warm before Replace battery or use a larger capacity battery Loosen coupling at driveshaft and move out driveshaft a small amount Remove boat from the water and obstacles Move powered transmitter a few feet from boat disconnect and reconnect battery to boat Power on ESC switch Move powered transmitter a few feet from boat disconnect and reconnect battery to boat TUMBLER Auto roll pool racer Problem Boat will not connect after binding to transmitter Boat tends to dive in the water or takes on water Boat tends to turn one direction Boat tends to turn one direction Rudder does not move Controls reversed Motor overheats Motor power pulses then motor loses power 10 11 Boat or transmitter is too close to Move boat and transmitter to another large metal object wireless location and attempt connecting source or another transmitter again Boat battery transmitter battery charge is too low ESC switch is off Power on ESC switch Dry out the boat and ensure the hatch is fully closed on the hull before returning the boat to the water The boat hull is not completely Center of gravity is too far forward Move battery back in the hul
11. nting overheating conditions Undue motor wear results from frequent turns stops and starts pushing objects boating in rough water or vegetation and boating continuously at high speed Over temperature protection is installed on the ESC to prevent circuit damage but cannot protect the motor from pushing against heavy resistance When you Finish Power off the ESC Disconnect the battery Power off the transmitter Remove the battery from the boat oN gt Tip Always store the boat open without the hatch and inner liner sealed or moisture may allow mold and mildew to grow in the boat Maintenance Always replace the shaft when it is damaged or shows visible wear or injury and property damage may result Lubricating the shaft is vital to the life of the drivetrain The lubricant also acts as a water seal keeping water from entering the hull through the stuffing box Lubricate the shaft propeller shaft and all moving parts after every 2 3 hours of operation Always replace any parts that show visible wear or damage 1 Loosen the coupling between the motor and the shaft 2 Loosen the setscrew from the shaft and remove the shaft from the back of the boat Tip Use paper or cloth to touch the shaft 3 Remove the drive shaft by sliding it out of the stuffing box Wipe lubricant and material from the shaft Lubricate the full length of the shaft assembly up to the drive dog using marine grease 7 11
12. ransport the boat with the battery connected to the ESC 4 Ensure the rudder moves in the proper direction when the controller is moved left or right 5 Pull the throttle to full then return the throttle to neutral ensuring the propeller turns counterclockwise The ESC auto sensing voltage cutoff will engage when the ESC detects a low battery charge Release the throttle and recharge the battery when necessary Testing Your Boat in the Water 1 Carefully place the boat in the water 2 Operate the boat at slow speeds near the shoreline Avoid objects in the water at all times 3 Once you are comfortable operating the boat at slow speeds it is safe to operate the boat farther from the shore Tip If you are using too much steering trim on your transmitter to make the boat drive straight return the trim to neutral and mechanically center the rudder To do this loosen the ball link 5 11 TUMBLER Auto roll pool racer from the rudder horn then turn the ball link on the linkage threads until the rudder is properly centered 4 Bring the boat back to shore when you notice the boat starting to lose speed 5 Power off the ESC and disconnect the battery packs 6 Allow the motor ESC and battery packs to cool before charging the batteries or operating the boat again NOTICE DO NOT TURN OFF THE TRANSMITTER FIRST OR THE RECEIVER MAY PICK UP STRAY SIGNALS AND RUN OUT OF CONTROL Boating Tips Avoid boating near other watercraft
13. ring the charge or discharge process the battery begins to balloon or swell discontinue charging or discharging immediately Quickly and safely disconnect the battery then place it in a safe open area away from flammable materials to observe it for at least 15 minutes Continuing to charge or discharge a battery that has begun to balloon or swell can result in a fire A battery that has ballooned or swollen even a small amount must be removed from service completely Never discharge a Li Po battery below 3V per cell Always disconnect a battery from the ESC when not in use Avoid continually operating to LVC Low Volt Cutoff as this could result in damage to the battery Store the battery partially charged approximately 50 charged 3 85V per cell at room temperature approximately 68 77 Fahrenheit F and in a dry area for best results When transporting or temporarily storing the battery the temperature range should be from approximately 40 100 F Do not store the battery or model in a hot storage car or direct sunlight whenever possible If stored in a hot garage or car the battery can be damaged or even catch fire Do not over discharge the LiPo flight battery Discharging the LiPo flight battery to a voltage that is too low can cause damage to the battery resulting in reduced power flight duration or failure of the battery entirely LiPo cells should not be discharged to below 3 0V each under load In the case of the 2 C
14. side of the boat including the water cooling lines and jackets around the motor and ESC Remove the hatch and radio box cover before storing your boat Repair any damage or wear to the boat Lubricate the flex shaft Make note of lessons learned from the trimming of your boat including water and wind conditions Tip The hook and loop strips in the boat retain water To dry them press on them with a dry cloth 8 11 TUMBLER Auto roll pool racer Troubleshooting Guide Problem Boat does not respond to throttle but responds to other controls Extra noise or extra vibration Reduced run time or boat underpowered Problem Boat will not Bind during binding to transmitter 9 11 Possible Cause Make sure throttle dual rate is turned Throttle servo travel is lower than Blocking or friction on shaft or propeller Battery capacity may be too low for conditions Drive dog is too close to the stuffing tube Vegetation or other obstacles block the rudder or propeller Transmitter is too near boat during binding process DO e eee Move boat and transmitter to another location and attempt binding again large metal object wireless source or another transmitter Boat battery Transmitter battery charge is too low ANOMEr combate ran SMNERIS Turn off all compatible transmitters except the one you are trying to bind powered on within range of the ESC switch is off Transmitter is too
Download Pdf Manuals
Related Search