CHARGER AMPLIFIER USER'S GUIDE
Contents
1. the charging LED turns green When the charging time or the charging voltage is exceeded the charging LED will turn red and flash to indicate the abnormal operations Please remove the pager from the charger to stop charging The charging green LED will remain flashing if ambient temperature is below 0 C or higher than 50 C Please remove the pager from the charger to stop charging 5 1 2 CHARGING SPARE BATTERIES Up to two NiMH batteries can be charged For best performance use the ones supplied by Unication Step 1 Put the rechargeable batteries into battery pocket as following illustration 13 OPERATION Step 2 Once the Ni MH rechargeable batteries are inserted correctly the charger amplifier will detect the batteries and start charging When the rechargeable batteries are being charged the charging LED turns orange Step 3 When the rechargeable batteries are fully charged the LED will turn green Step 4 When exceeding normal charging time or charging voltage the charging LED will turn red and flash to indicate the abnormal operations Please remove the spare batteries from the charger amplifier to stop charging 14 OPERATION 5 1 3 CHARGING EXTERNAL BLUETOOTH HEADSET Make sure the charging specification of your Bluetooth headset meets the charging limitation 4 5 V 6 5 V of the G1 Charger Amplifier Step 1 Insert the Bluetooth charging cable to the Charger Bluetooth headset charg2. 5 are 17 OPERATION inputs that are used to control the duration pins 2 and 3 remain shorted If pins 4 and 5 are shorted then pins 2 and 3 will remain shorted until the Reset keybutton is depressed If they are not shorted together the duration that pins 2 and 3 remain shorted is 10 seconds Step 3 Upon receiving a page the relay and audio output are activated ACCESSORY PIN 6 Ground Audio ENN PIN 3 PIN 4 Relay Dry Contact Relay Closure Timing PIN 5 PIN 2 Relay Closure Timng Relay Dry Contact 6 PRODUCT SPECIFICATIONS Main Charging Slot Spare Charging Slot BT Charging Socket Adaptor Input Output PRODUCT SPECIFICATIONS EE EE gt 6 1 GENERAL SPECIFICATION For Spare Ni MH Battery AAA For BT Headset USB A Type Input 100 240VAC 50 60 Hz Output 12Vdc 15A Normal Charge Current 800mA 2 4V 800mA 1 2V Spare Battery AAA 1 80mA 5 0V BT Headset Full Recharge Time 2 5 Hours PRODUCT SPECIFICATIONS Alert output 2106 dBSPL Audio Out 3 50 Earphone Jack 1 Ext Antenna Connector Bluetooth Charging Port Data Transfer RS485 DB 9 Female 1 DC Jack 12Vdc 15A 4 Pin Socket Horn Speaker DIN Jack 6 Pin DIN Jack 162 L x 115 W x 53 H mm BNC Jack 1 USB A Type 1 Terminal Block Dimensions Operation Handing Temperature PRODUCT SPECIFICATIONS 0 40 C Temperature Sto
3. U Unication CHARGER AMPLIFIER USER S GUIDE PREFACE 1 1 IMPORTANT SAFETY INFORMATION OVERVIEW 2 1 STANDARD PACKAGE DESCRIPTION 3 1 FRONT VIEW 3 2 REAR VIEW 3 3 LED INDICATOR INSTALLATION 4 1 POWER 4 2 ANTENNA OPERATION 54 CHARGING T 5 1 1 CHARGING G1 5 1 2 CHARGING SPARE BATTERIES 5 1 3 CHARGING EXTERNAL BLUETOOTH HEADSET 5 2 Voice Message Amplification 5 3 External Equipment Control 5 3 1 Horn Speaker 5 3 2 Fire Alert Indicator PRODUCT SPECIFICATIONS 6 1 GENERAL SPECIFICATIONS 6 2 POWER ADAPTOR SPECIFICATION 6 3 EXTERNAL ANTENNA SPECIFICATION 23 PREFACE 1 PREFACE E B Please read the following sections before using the G1 Charger Amplifier gt 11 IMPORTANT SAFETY INFORMATION To ensure the safe use of this product Use your charger only with the supplied power adapter Do not put a pager with a non rechargeable batteries inside into the charger Use the rechargeable batteries provided by Unication X Keep your charger away from high temperature high humidity dust chemicals and corrosive materials Do not disassemble your charger or power adapter This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interferen
4. ce received including interference that may cause undesired operation PX PREFACE A IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS AN DANGER TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK CAREFULLY FOLLOW THESE INSTRUCTIONS ZX For connection to a supply not in U S A use an attachment plug adapter of the proper configuration for the power outlet if needed OVERVIEW 2 OVERVIEW 2 1 STANDARD PACKAGE The standard Charger Amplifier contains Illustration Illustration DESCRIPTION 3 DESCRIPTION B g 3 1 FRONT VIEW Unication DESCRIPTION DESCRIPTION Speaker Volume Control Knob Pager Socket Spare Battery 2 Charging LED Spare Battery 1 Charging LED Reset Button Horn Speaker Status LED G1 Charging LED amp Power on LED Alert Light Spare Battery Socket DESCRIPTION gt 3 2 REAR VIEW DESCRIPTION Antenna Jack 4 Pin Socket Controller Jack 6 Pin DIN Jack Earphone Jack Bluetooth Headset Jack Power Socket LED INDICATOR gt 3 3 LED INDICATOR The following describes the different LED indicators Charger AMP Power LED amp G1 Charging LED On for 1 sec Power On Battery is charging Fully Charged Flashing Charging Error Spare Battery 1 Charging LED amp Spare Battery 2 Charging LED Spare Battery Steady Charging S
5. ing jack as following illustration Step 2 Connect Bluetooth headset with its charging cable gt 5 2 Voice Message Amplification Step 1 Turn the G1 on and place it in the Amplifier 15 OPERATION Step 2 Any received message will be amplified depending on the Amplifier s volume switch setting Step 3 Adjust the Amplifier s volume switch to a desired setting 5 3 External Equipment Control The Charger Amplifier provides a variety UO for external device control 5 3 1 Horn Speaker Step 1 With the G1 turned on place it in the Amplifier Step 2 Select RCA connector and make the external connections Step 3 When a message is received the relay closure is asserted and audio is active Step 4 Audio can be terminated by shutting the G1 off or depressing the Reset button on the G1 16 gt lt Horn Speaker Connector Pin OPERATION PIN1 wd III PIN 4 Horn Relay Contact Audio PIN 2 PIN 3 Horn Relay Contact Ground Audio 5 3 2 Fire Alert Indicator Step 1 Insert the G1 turned on in the Charger Amplifier Step 2 Using the DIN Connector connect the external equipment to the appropriate signaling pins Pins 1 and 6 are outputs and are used to control a remote speaker Pins 2 and 3 are outputs and are shorted upon a message being received and depending on the status of pins 4 and 5 remain in this condition until the Reset key button is depressed Pins 4 and
6. pare Battery Steady Charging Flashing Charging Error Alert Message Flashing Received Horn Speaker LED Horn Speaker Flashing 1 0 Enabled INSTALLATION 4 INSTALLATION a gt 4 1 Power G1 Charger Amplifier Power Sources Using the supplied 12VDC Adapter connect the AC end to a 110 60Hz receptacle and the 12VDC plug to the rear of the Amplifier labeled DC In Using the optional vehicle charger cable insert the cigarette lighter end in the vehicle s socket and the 12VDC plug to the rear of the Amplifier labeled DC In 4 2 Antenna Depending on the Transmitting frequency one of two types of antennas is used One antenna will accommodate both VHF and UHF applications and another is used for Low Band applications The appropriate antenna is affixed to the Amplifier s BNC connector located on the rear of the unit 11 OPERATION 5 OPERATION gt 5 1 CHARGING 5 1 1 CHARGING G1UNIT Ensure the rechargeable batteries are installed in the G1 For best performance use the rechargeable batteries supplied by Unication Step 1 Please insert the pager into the charger s pager pocket as in the following illustration Step 2 Step 3 NOTE OPERATION Once the pager is inserted correctly the charger amplifier will detect the batteries and start charging When the pager is being charged the charging LED is orange When the pager is fully charged
7. rage Temperature 10 60 C Certification CE FCC IC RoHs UL PRODUCT SPECIFICATIONS 6 2 POWER ADAPTOR SPECIFICATIONS Input Voltage AC 90 265V 47 63Hz Output Voltage DC 12V Output Current 15 Adaptor Power 18W DC Power Cord Length 18m Plug Type North America Adaptor 0 Efficiency 529 Charger Charging CC mode Constant Current Specification CV mode Constant Voltage PRODUCT SPECIFICATIONS gt 6 3 EXTERNAL ANTENNA SPECIFICATION 380 512MHz 138 174MHz Freguency Range 2 Input Return Loss lt 2 VSWR Antenna Length Weight Terminal Impedance U Unication For more information North America area please contact us at sales unication com Other areas please contact us at salesenquiry uni com tw Corporate Headquarter Unication Co Ltd Tel 886 2 22999678 Address 5F No 6 Wu Kung 5Rd Hsinchuang Dist New Taipei City 24890 Taiwan E mail salesenquiry uni com tw URL www uni com tw North America Branch Office Unication USA Inc Tel 817 303 9320 Address 1901 E Lamar Blvd Arlington TX 76006 U S A E mail salesQunication com G1 CAM ENG 20131105 V1 URL www unication com
Download Pdf Manuals
Related Search