User Guide
Contents
1. Color temperature Luminous intensity HMI 1200W 1 12 1 12 Distance m In case of replacement of the lamp or maintenance do not open the fixture within 15 minutes until the unit cools down after switching off Because of its high internal pressure there might be a risk that the Discharge lamp would explode during operation The lamp emits intense UV radiation which is harmful to the eyes and skin The high luminance of the arc can cause severe damage to the retina if looks directly at the lamp MSI 1200W S HMI 1200 S K SFc10 4 IF 575 HMI 575W amp HTI 575W Osram or HMQ 575 amp HMQ 575 2 Xenpow 1 Always switch off the main supply and never handle the lamp or luminant when it is hot 2 Do not touch the bulb with bare hands If this happens clean the lamp with denatured alcohol and wipe it with a lint free cloth before installation 3 The lamp generates UV radiation Never operate the lamp without appropriate shielding 4 When burning the lamp operates at high pressure and there is a slight risk of arc tube rupture The risk increases with age temperature and improper handling of the lamp Do not use the lamp any longer than its specified life 5 Make sure the lamp is located in the center of the reflector for the best spot Unscrew the thumb screw e nr ee 5F 6 If changing the lamp remove old lamp from lamp socket Hold the new lamp only by its ceramic base Never touch the glass bulb I2. UP button to change the mode Once the required mode has been selected press the ENTER button to setup or it will automatically return to the main functions without any change after idling 8 seconds To go back to the functions without any change press the MENU button The main functions are showing below Addr DMX512 Address Setting a IC Ltt Self Test MENU Fhrch Fixture Hours am Lamp on aff Lamp off rSPE Reset I i DMX 512 Address Setting Press the MENU button until the 2 is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Loo Self Test Press the MENU button until the JSk is blinking on the display Pressing ENTER button and the unit will run self test by built in program To go back to the functions press the MENU button again III L Fixture Hours Press the MENU button until the Fine 5 is blinking on the display Pressing ENTER button and the display will show the number of working hours of the unit To go back to the functions press the MENU button again 8F Reset Press the MENU button un
3. P i Z Solution Your integrated Solution TABLE OF CONTENTS 1 Safety Instruction Professional Intelligent Follow Spot LINKARLE 2 Technical Specification DMX512 a 2 1 Inserting Exchanging Rotating Gobos 2 2 Beam Angle 3 Lamp 4 How To Set The Unit 4 1 Control Panel 4 2 Main Function 4 3 Home Position Adjust 5 How To Control The Unit 5 1 Universal DMX Controller 5 2 Dedicated Controller 5 3 DMX 512 Configuration 5 4 DMX 512 Connection 6 Troubleshooting 7 Fixture Cleaning User Guide Professional Entertainment Technology 1 Safety Instruction A WARNING Please read the instruction carefully which includes important information about installation operation and maintenance Please keep this User Guide for future consultation If you sell the unit to another user be sure that they also receive this user guide Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit It s important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only and only in a dry location The unit must be installed in a location with adequate ventilation at least 50 cm from adjacent surfaces Be sure that no ventilation slots are blocked Disconnect main power before fuse lamp replacement or servicing Replace fuse
4. URS position enable the fixed colors function and disable the rainbow function They will save last setting automatically in each step 4 COLOUR buttons There are 9 color buttons of white red yellow magenta green orange blue pink and purple Select the light beam colors by pressing the relative color buttons 5 COLOUR TEMPERATURE switch Adjusting this switch to obtain 3 kinds of color temperature Standard 6000K 5600K and 3200K 11F 6 DIMMER slider Adjusting the slider from 0 to 100 position the light beam will become more stronger and stronger till the dimmer reach 100 7 SHUTTER slider Adjusting the slider from slow to fast position the strobe speed will become from slow to fast 8 IRIS slider Adjusting the slider from min to max position the light beam size will become more bigger and bigger till the iris opened fully 9 FOCUS slider Adjusting the suitable focus by pushing this slider from left to right 5 3 DMX512 Configuration DMX 512 Configuration 246 255 Open 255 Fast 171 255 3200K 255 100 554 1 r 247 Fast shutter 492 Slow 181 Slow MAN 128 Fast 113 127 Pink 099 112 UW purple r 065 098 Blue 071 084 Orange 086 170 5600K 016 Slow shutter 057 070 Green 043 056 Magenta 008 015 Open 029 042 Yellow 015 028 Red 000 014 White 000 085 6000K Wa us 12F 5 4 DMX512 Connection The DMX512 is widely used in intelligent lighting control with a maximum of 512 channels F h
5. damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics e Clean with soft cloth using normal glass cleaning fluid e Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55014 2 1997 A1 2001 EN61000 4 2 1995 EN61000 4 3 2002 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 amp Harmonized Standard EN 60598 1 2004 IEC 60598 1 2003 corrigendum 2004 Part 1 General requirements and test Following the provisions of the low voltage directive 73 23 EEC and 93 68 EEC 15F Technical Specifications n AC 230V 50 60Hz ower AC 100V 50 60Hz or 120V 60Hz only for HMI 575W version 6 x 30 mm Glass T15A HMI 1200W version use 6 x 30 mm Glass T10A HMI 575W version MSI 1200W S HMI 1200 S K SFc10 4 HMI 575W 1170 x 330 x 225 mm Dimension 405 x 360 x 35 mm Controller 42 4 kg HMI 1200W version Weight 38 kg HMI 575W version Innovation Quality Performance 16F 17F
6. e offset functions without any change press the MENU button again To go back to the main functions without any change after 8 seconds 9F Old fit LUN W Dimmer offset Press the MENU button for at least 5 seconds into offset mode use DOWN and UP button up to when the is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to adjust the dimmer home position Once the effect has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the MENU button again To go back to the main functions without any change after 8 seconds 5 How To Control The Unit Two ways to operate 1 By universal DMX controller 2 By dedicated controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show 1200 on the display and move all the motors to their home position and you may hear some noises for about 20 seconds After that the unit will be ready to receive DMX signal 5 1 DMX Controller If you use a universal DMX controller to control the units you have to set DMX address from 1 to 512 channels so that the units can receive DMX signal Press the MENU button up to when the Micicir ig shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 addres
7. lamp only with the same type Do not use any other type of lamp Make sure there are no flammable materials close to the unit while operating as it is fire hazard Use safety cable when fixes this unit Don t handle the unit by taking its head only but always by taking its base Maximum ambient temperature is TA 40 C Don t operate it where the temperature is higher than this Unit surface temperature may reach up to 85 C Don t touch the housing bare hand during its operation Turn off the power and allow about 15 minutes for the unit to cool down before replacing bulb or serving as the unit could be very hot In the event of serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Don t connect the device to any dimmer pack or power pack Do not touch any wire during operation as high voltage might be causing electric shock 2F Warning To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture Never touch bulb with bare fingers as it is very hot after using Hot lamp explosion hazard Do not open the unit within five minutes after switching off Do not start on the unit without bulb enclosure or housing are damaged The housing the lenses or
8. nsert the new lamp in the lamp socket 7 Please turn the head in horizontal position Hinge must be on the upper side of the head Turn screws left and remove plastic cover Loosen head screw and open the lamp cover 8 With the nipple of the lamp facing the back insert one end of the lamp into the socket Pull up the spring of the other side of the socket and snap the other end of the lamp into place Make sure it fits correctly into the socket Please refer to the diagram to know how to put the lamp in correct position 6F 4 How To Set The Unit 4 1 Control Panel DMX CONFIGURATION CH 1 SHUTTER i CH 2 IRIS CH 3 COLOR CH 4 COLOR TEMPERATURE CH 3 DIMMER ihe seins C DMX 512 LINK MAIN FUNG TION Rdde DMX512 Address Setting 1 5 ces ean o O agi Fitu MENU ENTER DMX IN DMX OUT AnP tame ONOFF coma PIN2 DMX PID DH UP DOWN Pind ONEXDMXIK PIMS 5W DMK IM Pind and pins is blank In DMX OUT Display To show the various menu and to select functions Button ENTER To confirm the selected functions On Off Turns On Off the power Fuse To replace the fuse Power To connect the power plug DMX input output For DMX 512 link use 5 pin XLR plug cable to link the unit together 7F 4 2 Main Function To select any of the given functions press the MENU button up to when the required one is showing on the display Select the function by ENTER button and the display will blink Use DOWN and
9. s Once the address has been selected press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later To go back to the functions without any change press the MENU button again Please refer to the following diagram to address your DMX512 channel for the first 4 units 10F 5 2 Dedicated Controller IF series has 6 channels for international protocol DMX512 It can finish all operations via dedicated controller without using other controllers When the power is switched on the projector automatically starts to run the self test After finishing these the fixture is ready for operation w DIMMER q DIMMER OPEN buttons Holding the buttons the light beam will become more stronger and stronger then shutter will obtain max value After un holding it the light beam and shutter resumes its initial condition There are 2 buttons on the both sides of the controller for your convenient operation 2 IRIS OPEN buttons Holding the buttons the light iris will become more bigger and bigger After un holding it the light beam resumes its initial condition There are 2 buttons on the both sides of the controller for your convenient operation 3 FIXED COLOURS amp RAINBOW switch Turning the switch on the RAINBOW position enable the rainbow function you can set different rainbow speed by pressing COLOUR buttons from slow to fast Turning the switch on the FIXED COLO
10. the ultraviolet filter must be replaced if they are visibly damaged Do not look directly at the light while the bulb is on e Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs by yourself If you need any service please contact your nearest dealer e Installation The unit should be mounted via its mounting system as show below Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 80 kgs for each unit SF 2 Technical Specification Power supply AC 230V 50 60Hz AC 100V 50 60Hz 120V 60Hz Only for IF 575 version Lamp MSI 1200W S HMI 1200 S K SFc10 4 HMI 575W amp HTI 575W Osram or HMQ 575 amp HMQ 575 2 Xenpow Optical system High efficiency optical system High quality optical lens and dichroic colors Beam angle 13 Shutter Dimmer Blackout 0 100 smooth dimming and strobe speed variable 1 12 flashes per second Movement Pan 360 Tilt 90 Color Wheel 8 dichroic colors plus white color Rainbow effect at variable soeeds Color Temperature Standard 6000K adjustable 5600K and 3200K DMX Channels Standard DMX512 signal addressing and controlled by any universal DMX controller Channel 1 Shutter Channel 2 Iris Channel2 tris OOOO Channel 3 Color Channel 4
11. til the aie is blinking on the display Pressing ENTER button and all channels of the unit will return to their standard position To go back to the functions press the MENU button again 4 3 Home Position Adjust Press MENU button for at least 5 seconds into offset mode to adjust the home position when you want to adjust gobo and color home position you should be run C mode first the functions are shown below idi ole EE Color offset 127 127 id MENU otFt a Effect offset 127 127 i 2 oid H Dimmer offset 127 127 Lt We ILL Color offset Press the MENU button for at least 5 seconds into offset mode use DOWN and UP button up to when the is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to adjust the color home position Once the color has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the MENU button again To go back to the main functions without any change after 8 seconds LLL JEI L Effect offset Press the MENU button for at least 5 seconds into offset mode use DOWN and UP button up to when the amp jis shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to adjust the effect home position Once the effect has been selected press the ENTER button to setup or automatically return to th
12. ve signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 13F 6 Troubleshootino Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The unit does not work no light and the fan does not work 1 Check the connect power and main fuse 2 Measure the mains voltage on the main connector 3 Check the power on LED B Not responding to DMX controller 1 Check the address settings and DMX polarity 2 If you have intermittent DMX signal problems check the pins on connectors or on PCB of the unit or the previous one 3 Try to use another DMX controller 4 Check in the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit C One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition D The lamp is cutting out intermittently 1 The lamp is not working well Check the main voltage either too high or too low 2 Internal temperature may be too high Check and if necessary replace the fan 14F 7 Fixture Cleanino The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates
13. y wr a Ti a i F ne e ae p a a Ee F e th 120 ohm 1 4W OUTPUT Termination reduces signal errors and to avoid signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture 1 If you using a controller with 5 pins DMX output you need to use a 5 to 3 pin adapter cable 2 At last unit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last unit 3 Connect the unit together in a daisy chain by XLR plug from the output of the unit to the input of the next unit The cable can not branched or split to a Y cable DMX512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 4 The DMX signal is able to pass through each fixture continuously so if one fixture in the chain is out of order all the fixtures after this point will not be affected 5 Each lighting unit needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually 0 amp 1 are equal to 1 6 The end of the DMX512 system should be terminated to reduce signal errors 7 3 pin XLR connectors are more popular than 5 pin XLR 3 pin XLR Pin 1 GND Pin 2 Negati
Download Pdf Manuals
Related Search