user guide - Smart-e
Contents
1. 10 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX100 1 Connecting SLX RX100 to the display device 1 1 Making sure that the Cat 5 cable is connected to the SLX TX16 output connect the cable to the RJ45 socket on the receiver unit 1 2 If the cable connection is correct the power LED on the front of the receiver should illuminate power is sent up the Cat 5 cable Connect the display to relevant connector on the receiver see diagram below using the appropriate cable Cat5 from ks Transmitter Matrix PSU connection is not required unit is powered from the Cat5 cable Speakers Monitor 11 Smart e UK Ltd e Hale House Barns e OQakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX100 2 Setting the cable length dials The Receiver unit is preset for approximately 50m which is sufficiently accurate for most applications However if the image does not look sharp enough then follow the instructions below 2 1 Whilst looking at an image on the display preferably a long horizontal bar adjust the CABLE COMPENSATION dial 2 2 Looking at the right hand edge of the bar you will see the image change A highlighting bright edge means over compensation whils2. Installation and Operation SLX RX1 1 1 SLX RX111 The SLXY RX111 allows for the Short Range reception of UXGA RGsB RGBS YPrPb YUV and Long Range reception of Y C CVBS Stereo Audio and Infra Red or RS232 control signals when broadcasted along a single Cat UTP cable from a Smart e transmitter or matrix The signals are received along the Cat5 from the transmitter and then distributed to the display and control equipment via the appropriate connection and to speakers via a 3 5 mm mini jack 14 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX1 11 1 Connecting SLX RX111 to the display device 1 1 Making sure that the Cat 5 cable is connected to the SLX TX16 output connect the cable to the RJ45 socket on the receiver unit 1 2 If the cable connection is correct the power LED on the front of the receiver should illuminate power is sent up the Cat 5 cable 1 3 Connect the display to relevant connector on the receiver see diagram below using the appropriate cable 1 4 If R5232 control is required then connect to the display via the 3 5mm minijack on the receiver using a CAB J19 1M Cat5 from Transmitter Matrix PSU connection is not required unit is powered from the EC Cat5 cable Component YPbPr S Video Y C UXGA RGBHV Scart RGBS or Composite
3. Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX212 D 3 Adjusting Equalisation and Contrast 3 1 To adjust equalization the pot labelled as EQ may be rotated clockwise start by turning the pot completely ANTI clockwise and then slowly turn clockwise until equalization is correct As cable length increases the pot will need to be turned further clockwise To adjust contrast Gain as with equalization begin by turning the pot completely ANTI clockwise and slowly turn the pot clockwise until the desired image contrast Gain is displayed 4 Skew error compensation The SLX RX212 has built in delay lines to compensate for skew error in longer cable lengths Each video colour can be delayed up to Gens which can be adjusted and set using the 3 buttons on the base of the unit 4 1 4 2 4 3 4 4 4 5 Note Press buttons INC and DEC together to enter the setting mode Press button SET to select the colour to be delayed i e red green blue Press the INC button to increase and DEC button to decrease the delay Press buttons INC and DEC together to save the settings Pressing buttons DEC and SET together will reset all delays to zero Although all 3 colours can be delayed it is usually only nec
4. Cat5 cable SM EYE IR Receiver Audio 1 Audio 2 Audio 3 20 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX2 1 1 3 Adjusting Cable Compensation Equalization and Contrast Control 3 1 To adjust equalization the pot labelled as Cable Compensation may be rotated clockwise start by turning the pot completely ANTI clockwise and then slowly turn clockwise until equalization is correct As cable length increases the pot will need to be turned further clockwise The Contrast Control adjustment Gain is factory set at OdB Leave at preset unless you require to compensate for another piece of equipment in the chain i e old display which has lost brightness 4 Skew error compensation The SLX RX211 has built in delay lines to compensate for skew errors in longer cable lengths of Cat6 cable Each video colour can be delayed up to 62ns which can be adjusted and set using the 3 buttons on the base of the unit 4 1 Press buttons INC and DEC together to enter the setting made 42 Press button SET to select the colour to be delayed i e red green blue indicated by the respective LED 43 Choose the most delayed colour the one which is to the right of the other colours and delay the other 2 colours to that position 44 Press the INC button to
5. as Broadcast Video TV video signal Computer Video VGA SVGA SXGA and etc signals and various formats of Audio signals Why is SmartLynx necessary Sometimes AV signals need to be transmitted over distances greater than commonly specified product limitations of 5m In this case several choices are available but most are expensive and bulky which is in some cases simply not practical due to space limitations in the conduits The SmartLynx allows the transmission of AV signals over a standard Cat5 UTP cable over distances of up to 300m The actual distance is a function of the signal resolution and cable quality The following is a rough guide to distance and resolution Cat5 Cable Length Maximum Recommended Resolution 150m UXGA 1600x1200 200m HDTV 720p 1080i 1080p 300m SDTV SVGA 800x600 How does SmartLynx work The Smart e SmartLynx systems are transmitter and receiver pairs designed to extend video stereo audio and IR RS232 signals over UTP unshielded twisted pair category 5 Cat5 cabling They are supplied with a UK power supply and consist of a transmitter with a video input connectors vary by model an audio input and a Cat output and a receiver with a cat input and corresponding outputs Certain models are also supplied with local outputs and or IR or RS232 connections The extended signals depends on the model but supported signals are UXGA CVBS VUM YPbPr Y C RGsB and RGBS analogue format and Stereo Au
6. audio input of the transmitter using the appropriate cable If using RS232 or Infra Red see Blaster installation on the following pages Stereo Audio Stereo Audio a DVD Player Computer A Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk 3 1 The diagram below details how to correctly set the jumpers for the required video type VGA or RGBS for VGA the jumper should be in the top position for RGBS it should be at the bottom Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA 44 0 1306 628264 44 0 1306 628074 info smart e co uk www smart e co uk Installation and Operation 4 Connecting the IR Blaster unit optional 4 1 Using the IR Blaster control cable attach one end into the IR control port on the rear of the SLX TX16 and the other end to the rear of the 1U Blaster unit Then plug the IR emitter LED into the relevant 3 5mm jack socket on the front of the Blaster unit and position the LED at the device to be controlled Making sure that the Blaster port number corresponds to the video input number on the SLX TX16 See IR output 12 on the Blaster corresponding to video input 12 on the Transmitter in the diagram below DVD Player SM LED IR Emitter Output 12 6 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0
7. e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Technical Information SLX RX212 D Video input Signal Type Connector UXGA YUV YPbPr YC CVBS RJ45 Bandwidth 400MHz Impedance 75 Ohm Audio Input o Signal Type Stereo Audio Bandwidth 2OkHz OdB Impedance 10k Ohm Connector RJ45 Video Output Signal Type Connector UXGA YUV YPbPr YC CVBS 2 x HD15 RU45 on SLX RX212D Bandwidth 400MHz Impedance 75 Ohm Audio Output Signal Type Stereo Audio Bandwidth u 2OkHz OdB Impedance 100 Ohm Connector 3 x 3 5mm mini jacks Female RJ45 on SLX RX212D Signal Type 30 500kHz modulated IR 3 5mm minijack Female 30 500kHz modulated 3 5mm minijack Fema RS232 up to 115kbaud full duplex tx rx R5422 9600baud 3 5mm minijack Female RS232 up to 115kbaud full duplex tx rx R5422 9600baud 3 5mm minijack Female 24VDC 500mA 5mm x 2 1mm 36 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Troubleshooting No video 1 Are the green LEDs on both the transmitter and receiver units If not check that the 24V power supply PSU is connected and the LED on the PSU is lit Check the cable compensation dials on the underside of the unit Over compensation of
8. larger than the holes ee MOUNTING HOLES LLEXY XIS ER lt gt 4 NOS UEUUIS MAAN En CONTRAST i CONTROL 6db TO 6db o Ser CABLE COMPENSATION 02 tc a A Pas N J zZ BANTS H e i DF 3g 7A v rol S a ZS o 2G zb ES ER lt Z BE for 52 a lt 9 IOl MOUNTING HOLES a 23 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 i 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX212 D SLX RX212 D The SLX RX212 allows for the Long Range reception of UXGA RGsB YPrPb YUV Y C CVBS Stereo Audio and Infra Red or RS232 control signals when broadcasted along a single Cat5 UTP cable from a Smart e transmitter or matrix The signals are received along the Cat5 from the transmitter and then distributed as a Dual Screen output to the displays and control equipment via the appropriate connections and to speakers via a 3 5 mm mini jack 24 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX212 D 1 Connecting SLX RX212 to the display device 1 1 1 2 1 3 1 4 Cat5 from Transmitter Matrix Making sure that the Cat 5 cable is connected to the transmitter output connect the cable to the RJ45 socket on the receiver
9. mounting hole points for fixing to the wall or screen See diagram below Simply hold receiver in place mark position of holes and set screws in these locations NB Always use screws with heads larger than the holes a MOUNTING HOLES LeXa X1S he ns 4 MDOOe UEUIS MMM H CABLE COMPENSATION ci DEC Le INC ATAR DEN 9 WEWS ei 6db Format 2 HD15 RGB SET CONTRAST CONTROL z VGA z YPbPr c Format R Both HD15s g le G2 2s Vela MOUNTING HOLES Se 31 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Wun JOAIB09y JOMOd AUI UI ZETSY yl olpny 08184S 0 P A FEWJOJ HININ Technical Information SLX TX16 Video Input Signal Type Connector UXGA RGBS YUV YPbPr YC CVBS HD15 Bandwidth 400MHz Impedance 75 0hm Audio Input Signal Type Stereo Audio Bandwidth 2OkHz OdB Impedance 10k Ohm Connector 3 5mm minijack Female Local Audio Output ifapp Signal Type Stereo Audio 2OkHz OdB 100 Ohm Connector 3 5mm minijack Female Video Output Signal Type Connector UXGA RGBS YUV YPbPr YC CVBS RJ45 Bandwidth 400MHz Impedance 100 Ohm Audio Output Signal Type Stereo Audio Bandwidth 2OkHz OdB Impedance 100 Ohm Connector RJ45 30 500kHz modulated IR RJ45 30 500kHz modulated IR D15 to IR Blaster Signa
10. unit If the cable connection is correct the power LED on the front of the receiver should illuminate power is sent up the Cat 5 cable Connect the displays to the relevant connectors on the receiver see diagram below using the appropriate cable If R5232 control is required then connect to the display via the 3 5mm minijack on the receiver using a CAB J19 1M PSU connection is not required unit is powered from the Cat5 cable UXGA 2 RGBHV UXGA 1 RGBHV 25 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e DD SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX212 D 2 Connecting SLX RX212 to audio and Infra Red control 2 1 Connect the speakers or audio inputs on the displays to the audio outputs on the receiver using 3 5mm jack plugs 2 2 If using the receiver to transmit Infra Red signals back down the cable to the transmitter unit then connect an eye to the jack position as shown in the diagram below If using the receiver to transmit Infra Red signals up to the display from the transmitter unit then connect a LED to the jack position as shown in the diagram below Please note connecting the IR eye will prevent the return RS232 path from the display Cat5 from Transmitter Matrix pots e RS232 powered from the SM LED IR Emitter Caro cable SM EYE IR Receiver i Audio 1 Audio 2 26
11. 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation 5 System Power up 5 1 Turn the system on by plugging in the power adapter to the SmartLynx if they are not yet connected See diagram opposite Power up your computer Observe both transmitter and receiver power LED are ON and source device is switched on 6 Preparing and connecting System CAT 5 cable The SmartLynx utilizes category D CAT DL unshielded twisted pair UTP cable to transport signal between transmitter and receiver CAT 5 cable is more desirable than coaxial cable due to its low cost and ease of installation This cable is used for LAN applications and is found in abundance already installed in many buildings The category 5 is a standard which establishes minimum requirements for telecommunications cabling within a commercial building The standard covers various aspects of wiring including telecommunications outlets Following is the wiring standard for terminating CAT 5 cable using RJ 45 connector nloln 12345678 Pins 1 amp 2 Pins 3 amp 6 Pins A 6 amp 5 Pins 7 amp 8 Connectors RJ 45 Capacitance 14 pf ft 46 2 pf m Conductor Gauge 24 AWG Impedance 100 15 ohms 4 Pair Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Receiver Options 7 Smartlynx Re
12. 15 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX1 11 2 Connecting SLX RX1 11 to audio and Infra Red control 2 1 Connect the speakers or audio input on the display to the audio output on the receiver using a 3 5mm jack plug 2 2 If using the receiver to transmit Infra Red signals back down the cable to the transmitter unit then connect an eye to the jack position as shown in the diagram below If using the receiver to transmit Infra Red signals up to the display from the transmitter unit then connect a LED to the jack position as shown in the diagram below Please note connecting the IR eye will prevent the return RS232 path from the display Cat5 from Transmitter Matrix PSU connection is not RS232 required unit is powered from the SM LED IR Emitter Cat5 cable SM EYE IR Receiver Audio 1 Audio 2 Audio 3 16 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX1 11 3 Mounting the Receiver The receiver unit can compensate for cable losses over a length of 20 100m and for mounting purposes the unit is provided with two mounting hole points for fixing to the wall or screen See diagram below
13. 5 Video on Both HD15s Red Green Blue O Q RAO O BueO O O L l For YPrPb O O O 29 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX2 12D D How to Cascade the SLX RX212D 6 1 As well as having all the functions of the regular SLX RX212 the SXL RX212D also has the ability to be cascaded for up to 5 units 6 2 In order to cascade the SLX RX212Ds Cat5 cable should be used to join together the supplementary units with the Cat5 output on the first unit to be joined to the Cat input on the second unit etc See diagram below All additional SLX RX212Ds connected after the initial unit MUST have their own power supply units attached DC24V 20W PSU SLX RX212D Cascading Cat 5 cable e E from Smart e Cat 5 cable Cat 5 cable transmitter To next SLX RX212D To next SLX RX212D 6 4 All SLX RX2 12Ds then connect to display and audio equipment as shown for the standard unit on the previous pages 30 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX212 D 7 Mounting the Receiver The receiver unit can compensate for cable losses over a length of 20 100m and for mounting purposes the unit is provided with two
14. ON CONTRACT TORT OR ANY OTHER LEGAL THEORY AND WHETHER ADVISED OF THE POSSIBILITY OF SUCH DAMAGES D Local law To the extent that this warranty statement is inconsistent with local law this warranty statement shall be considered modified to be consistent with such law 38 Partial Product List Product Range Product Code Description SmartLynx X SLX 100 Transmitter and Receiver Pair SLX 400 Transmitter and Receiver Pair SmartLynx X Transmitter and Receiver Pair with RS232 1R Transmitter and Receiver Pair with RS232 I1R Dual Transmitter and Receiver Pair with RS232 1R SCX TX600 One to Six Transmitter Unit SCX TX550 One to Five Transmitter Unit with RS232 I1IR SmartCast System TUSC 1042 SmartCast Eurocard Rack Up to 16 cards SCX TX120E Dual Screen Transmitter Eurocard SCX TX550E One to Five Transmitter Eurocard with RS232 1R SLX RX100ES_ Eurocard Receiver for UGXA YUV Y C and Audio SmartNet X SNX 8x8 8 x 8 Distribution Matrix Matrix Switches SNX 16x16 16 x 16 Distribution Matrix Up to 256 x 256 SmartNet X SNX 8X8IRP Complete Infrared Controlled 8X8 Matrix Package Matrix Bundles SNX 8X8RSP Complete RS232 Controlled 8X8 Matrix Package Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk
15. S Bandwidth 400MHz Impedance Audio Output Signal Type Stereo Audio Bandwidt 20kHz OdB Impedance 100 Ohm Connector 3 x 3 5mm mini jacks Female Signal Type 30 500kHz modulated IR Connector 3 5mm minijack Female Signal Type Connector Signal Type RS232 up to 115kbaud full duplex tx rx RS422 9600baud Connector Signal Type RS232 up to 115kbaud full duplex tx rx RS422 9600baud Connector a 3 5mm minijack Female 24VDC 500mA 5mm x 2 1mm 34 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Technical Information SLX RX2 1 1 Wee o i Signal Type Connector UXGA RGBS YUV YPbPr YC CVBS RJ45 Bandwidth 400M Hz Impedance Audio Input o Signal Type Stereo Audio Bandwidth 2OkHz OdB Impedance 10k Ohm Connector Signal Type Connector UXGA HD15 RGBS YUV 3xRCA YC 4pin minidin CVBS Bandwidth 400MHz Impedance Signal Type Stereo Audio Bandwidth 20k z OdB Impedance 100 Ohm Connector 3 x 3 5mm mini jacks Female Signal T 30 500kHz modulated IR 3 5mm minijack Female 30 500kHz modulated IR RS232 up to 115kbaud full duplex tx rx R5422 9600baud RS232 up to 115kbaud full duplex tx rx R5422 9600baud 3 5mm minijack Female 24VDC 500mA 5mm x 2 4mm 35 Smart e UK Ltd e Hale House Barns e Oakwoodhill
16. SLX long range transmitter system for more information visit our website or talk to one of our technical team tel 44 0 1306 628264 www smart e co uk Smart amp Notice The information contained in this document is subject to change without notice Smart e makes no warranty of any kind with regard to this material including but not limited to implied warranties of merchantability and fitness for particular purpose Smart e will not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material No part of this document may be photocopied reproduced or translated into another language without prior written consent from Smart e UK Ltd Edition 3 July 2008 Copyright 2008 Smart e UK Ltd Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Table of Contents Introducing SmartLynx What s in the box What is SmartLynx Why is SmartLynx necessary How does SmartLynx work Installation and Operation Rack Mounted Transmitter Receiver Options Appendix Specifications Troubleshooting Limited warranty statement Partial Product List Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Introd
17. Simply hold receiver in place mark position of holes and set screws in these locations NB Always use screws with heads larger than the holes a MOUNTING HOLES lolol H Gad y Moroneus mnm Smart SLX RX111 Multi format Video Stereo Audio IR RS232 Inline Power Receiver Unit o o LU GN lt eg ICH made in uk MOUNTING HOLES eg 17 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX2 1 1 SLX RX211 The SLX RX211 allows for the Long Range reception of UXGA RGsB RGBS YPrPb YUV Y C CVBS Stereo Audio and Infra Red or R8232 control signals when broadcasted along a single Cat5 UTP cable from a Smart e transmitter or matrix The signals are received along the Cat5 from the transmitter and then distributed to the display and control equipment via the appropriate connection and to speakers via a 3 5 mm mini jack 18 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX2 1 1 1 Connecting SLX RX21 1 to the display device 1 1 Making sure that the Cat 5 cable is connected to the SLX TX16 output connect the cable to the RJ45 socket on the receiver unit 1 2 If the cable connection is correct the po
18. ceiver Options There are a number of different receiver options available to accompany the SLX TX16 please check the model number and relevant page number reference below SLX RX100 UXGA RGsB YPrPb Y C CVBS and Stereo Audio For Instructions on Installation of the SLX RX100 see page SLX RX1 11 UXGA RGBS RGsB YPrPb Y C CVBS Stereo Audio and RS2382 or Infra Red control option For Instructions on Installation of the SLX RX111 see page SLX RX2 1 1 Same as SLX RX111 but with greater range and skew compensation For Instructions on Installation of the SLX RX211 see page 8 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Receiver Options SLXRX212 D Dual Screen Output UXGA RGsB YPrPb Y C CVBS and Stereo Audio with RS232 or Infra Red control option SLX RX212D can be cascaded 9 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX100 SLX RX100 The SLX RX100 allows for the reception of UXGA RGsB YPrPb YUV Y C CVBS and stereo audio when broadcasted along a single Cat5 UTP cable from a Smart e transmitter or matrix The unit then distributes the received signal to a display via a HD15 connection and to speakers via a 3 5mm mini jack
19. dio The basic concept behind this product is the ability to encode and decode analogue signal combined with precise line equalization and compensation p Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation 1 Preparing for installation Start installation process by ensuring that all video displays and audio devices are compatible with the computers being used This is accomplished by connecting the devices directly to the computer and checking that the devices operate as desired without the SmartLynx system Infra Red Receiver Eye Speakers K Cat5 to q e Receivers Speakers Monitor 2 SLX RX111 Kg lt d Monitor 1 Monitor Fig 1 Install CAT 5 wiring between desired locations In order to minimize system operation difficulties avoid routing the system cables near fluorescent lights air conditioners or machines that may create electrical noise Bech Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation 2 Connect Transmitter to the signal sources 2 1 Connect the video output of the source device to the input of the transmitter using the relevant interface cable if relevant 2 2 Connect the audio output of the source device to the
20. ditions If Smart e receives during applicable warranty period notice of defect Smart e will at its discretion replace or repair defective product If Smart e is unable to replace or repair defective product covered by the Smart e warranty within reasonable period of time Smart e shall refund the cost of the product Smart e shall have no obligation to repair replace or refund unit until customer returns defective product to Smart e Any replacement product could be new or like new provided that it has functionality at least equal to that of the product being replaced Smart e warranty is valid in any country where the covered product is distributed by Smart e B Limitations of warranty TO THE EXTENT ALLOWED BY LOCAL LAW NEITHER SMART E NOT ITS THIRD PARTY SUPPLIERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND WHETHER EXPRESSED OR IMPLIED WITH RESPECT TO THE SMART E PRODUCT AND SPECIFICALLY DISCLAIM IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE C Limitations of liability To the extent allowed by local law the remedies provided in this warranty statement are the customers sole and exclusive remedies TO THE EXTENT ALLOWED BY LOCAL LAW EXCEPT FOR THE OBLIGATIONS SPECIFICALLY SET FORTH IN THIS WARRANTY STATEMENT IN NO EVENT WILL SMART E OR ITS THIRD PARTY SUPPLIERS BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES WHETHER BASED
21. essary to delay 2 of the colours to achieve skew error compensation ZLeXY X1S lt gt 4 YNO 3 HLEWS MMM INC CABLE COMPENSATION DEC YN 6db ZLEXY XIS 9 EWS SET CONTRAST CONTROL YUN 19A1899Y Jeu BUI UI ZEZTSY Hun 0819 S 08P1A JEUOJ HINN VGA YPbPr Gef ll d made in uk Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk In this example the Green is under equalized and the Red is slightly over equalized Skew error test signal In this example colours are in alignment and hence correctly equalized Skew error test signal Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA 44 0 1306 628264 44 0 1306 628074 info smart e co uk www smart e co uk Installation and Operation SLX RX212 D 5 Setting the jumpers on the Receiver 5 1 On the SLX RX212 you are able to select the format of video outputted by the HD15s by altering the jumpers on the base of the unit shown in the diagram below ZLZXY XIS fe lt gt A MO S UEUUS MMM 2 INC CABLE COMPENSATION EY D N io HNN DEC d cLeXY X1S ei 6db SET CONTRAST CONTROL up Jeng BENO SI ul olpny oa1a s oapi ewu VGA YPbPr SE Format R oth HD15s g B A el made in uk Viewed from underside of board where the pots reside Video on Second HD1
22. increase and DEC button to decrease the delay 45 Press buttons INC and DEC together to save the settings 46 Pressing buttons DEC and SET together will reset all delays to zero Note Although all 3 colours can be delayed it is usually only necessary to delay 2 of the colours to achieve skew error compensation LENS ie H CONTRAST CONTROL LLZXY XIS EIER SEET 0 D CABLE COMPENSATION made in uk 2 21 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk EQ LEDs Wun Joie Jemog Su Hong 0333 S 03P In this example the Red signal is most delayed and the Green signal the least delayed Skew error test signal In this example colours are in alignment and hence correctly equalized Skew error test signal Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA 44 0 1306 628264 44 0 1306 628074 info smart e co uk www smart e co uk Installation and Operation SLX RX2 1 1 5 Mounting the Receiver The receiver unit can compensate for cable losses over a length of 20 100m and for mounting purposes the unit is provided with two mounting hole points for fixing to the wall or screen See diagram below Simply hold receiver in place mark position of holes and set screws in these locations NB Always use screws with heads
23. l Type RS232 up to 115kbaud full duplex tx rx R5422 9600baud Connector D9 Signal Type RS232 up to 115kbaud full duplex tx rx R5422 9600baud Connector RJ45 Voltage Frequency 90 230V 50 60Hz Connector IEC Mains Lead 2U 88mm 19 205mm 32 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Technical Information SLX RX100 Wee o Signal Type Connector UXGA YUV YPbPr YC CVBS RJ45 Bandwidth 400MHz Impedance Signal Type Bandwidth 2OkHz OdB Impedance 10k Ohm Connector Signal Type Connector UXGA YUV YPbPr YC CVBS HD15 Bandwidth 400MHz Impedance 75 Ohm Auge Signal Type Stereo Audio Bandwidth 20k z OdB mpedance 100 Ohm Connector 3 x 3 5mm mini jacks Female Requirement Connector 24VDC 500mA 5mm x 2 1mm Beef Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Technical Information SLX RX1 1 1 Video Input Signal Type Connector UXGA RGBS YUV YPbPr YC CVBS RJ45 Bandwidth 400MHz Impedance a 75 Ohm Augen Signal Type Stereo Audio Bandwidt 20kHz OdB Impedance 10k Ohm Connector Signal Type Connector UXGA HD15 RGBS YUV 3xRCA YC 4pin minidin CVB
24. t a blurred dark edge means under compensation 2 3 Adjust the dial until both effect are neutralized The Contrast control dial is factory pre set and usually needs no adjustment UXGA Stereo Audio Line Power Receiver Unit VIDEO TYPE SELECTION CONTRAST CONTROL x x kel o g WS E e z CABLE COMPENSATION made in uk Contrast control adjusts signal gain Cable compensation adjusts all three Colours together from 0 to 300m Model SLX RX100 12 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX100 3 Sync Processing For VGA applications the Transmitter adds the Horizontal and Vertical Sync Pulses to the Blue and Red channels However since the unit has been designed for use with other types of video the Receiver provides the ability to pass both the Red and Blue channels transparently or process them to remove the Sync Pulses lt Q gt O Green B Red O O O Blue 3 1 For composite y c and Y P P component the jumpers must be set in the Video position 3 2 For VGA the jumpers must be set in the VGA position The example below shows the jumpers set for composite s video or component Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e DD SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk
25. the Red and Blue channels can cause the display to misinterpret the sync pulses and not display an image 2 Is the video source a laptop or floating a floating source is one which has no earth reference i e uses a double insulated PSU or a figure 8 mains cable If so make sure the PSU is an earthed unit when not using the PSU supplied 3 Is the audio input level too high The audio level should be set to line level OdB or 700mV peak to peak to prevent interference Display has problems syncing 1 Is the audio input level too high The audio level should be set to line level OdB or 700mV peak to peak to prevent interference 37 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Appendix Limited Warranty Statement A Extent of limited warranty 1 Smart e UK Ltd warrants to the end user customers that Smart e product specified above will be free from defects in materials and workmanship for the duration of 3 years which duration begins on the date of purchase by the customer Customer is responsible for maintaining proof of date of purchase Smart e warranty covers only those defects which arise as a result of normal use of the product and do not apply to any a Improper or inadequate maintenance or modifications b Operations outside product specifications c Mechanical abuse and exposure to severe con
26. ucing SmartLynx Cat5 AV Extender What s in the box Thank you for buying the Smart e SmartLynx Rack Mountable Cats AV Extender Depending on the configuration of your system various quantities of the parts below may be included in your shipment If any of the accessories listed below are missing please contact the Smart e dealer you purchased products from or contact Smart e customer support at 44 0 1306 628264 If you ordered a SmartLynx SLX TX16 Item Description SLX TX16 Transmitter Unit 16 Inputs and 16 Cat5 Outputs Yes Mains Cable IEC Mains Lead Yes If you ordered SmartLynx Single Screen Receivers Description SLX RX100 SLX RX111 SLX TX211 Short Range Receiver Unit 1 Cat5 Input and 1 Output Long Range Receiver Unit 1 Cat5 Input and 1 Output If you ordered SmartLynx Dual Screen Receivers Item Description SLX RX212 SLX RX212D Receiver Unit 1 Cat5 Input and 2 Outputs Yes No Cascadable 1 Cat5 Input 1 Cat5 Output Receiver Unit 2 Standard Outputs Ne 1 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e DD SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Introducing SmartLynx Cat5 AV Extender What is SmartLynx The SmartLynx systems are a combination of transmitter and receiver devices designed to transmit high resolution computer video and or audio signals over Cat5 wire AV stands for Audio Visual and includes such signal formats
27. wer LED on the front of the receiver should illuminate power is sent up the Cat 5 cable 1 3 Connect the display to relevant connector on the receiver see diagram below using the appropriate cable 1 4 If RS232 control is required then connect to the display via the 3 5mm minijack on the receiver using a CAB J19 1M Cat5 from Transmitter Matrix PSU connection is not required unit is powered from the CEC Cat5 cable Component YPbPr S Video Y C UXGA RGBHV Scart RGBS or Composite 19 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e DD SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX2 1 1 2 Connecting SLX RX211 to audio and Infra Red control 2 1 Connect the speakers or audio input on the display to the audio output on the receiver using a 3 5mm jack plug 2 2 If using the receiver to transmit Infra Red signals back down the cable to the transmitter unit then connect an eye to the jack position as shown in the diagram below If using the receiver to transmit Infra Red signals up to the display from the transmitter unit then connect a LED to the jack position as shown in the diagram below Please note connecting the IR eye will prevent the return RS232 path from the display Cat5 from Transmitter Matrix PSU connection is not RS232 required unit is powered from the SM LED IR Emitter
Download Pdf Manuals
Related Search