USER GUIDE - Henley Designs Ltd.
Contents
1. 10 CID CIA BY PRO JECT AUDIO SYSTEMS INSTRUCTIONS FOR USE Pro Ject Stereo Box S Phono Dear music lover thank you for purchasing a Pro Ject Audio Systems amplifier In order to achieve maximum performance and reliability you should study these instructions for use carefully V Warning of a hazard for the user the unit or possible misuse 15 Important notice Connectors Pro Ject Audio Systems Vienna Austria sb Power 34 O NI ORO SMK N4 O N3 N PHONO O oto da O O O CE rons a E i A e O Make all connections whilst the amplifier is disconnected from the power supply Take care to connect the left and right channels correctly The right channel is usually marked red the left channel black or white V The red speaker terminals carry the positive signal the black speaker terminals the negative signal Make sure the polarity of the connection is correct at each end of the cables Only connect one loudspeaker with an impedance not less than 4 ohms per channel Never use any other power supply than the one supplied with the unit Connecting line level sources Line level sources such as CD player radio or TV can be connected to the input sockets marked IN2 IN3 or IN4 Connecting the record player MM or high output MC cartridges only Connect the tone arm signal lead to the IN1 The earthing wire may be connected to the screw terminal if you encounter hum problems when usi2. ce the battery Make sure the battery is the right way round e Close the battery case cover Battery type 1 x CR2032 3V or 1 x CR2025 3V Do not dispose the batteries as ordinary domestic refuse Please dispose your exhausted batteries at the appropriate collection sites usually located at supermarkets and drugstores Technical specifications Pro Ject Stereo Box S Phono Power output 2 x 25W 37W at 8 ohms 4 ohms both channels driven Frequency response 20Hz 20kHz 0 2dB Channel separation gt 40dB at 20kHz Noise floor gt 100dB A weighted THD lt 0 05 at 10W Gain 22dB Line level inputs 2 pairs RCA phono sockets IN3 IN4 3 5mm co axial jack IN2 Phono amplifier Moving magnet MM RIAA egualisation curve accuracy 20Hz 20kHz max 0 5dB Phono input 1 pair RCA phono sockets IN1 Input impedance 20kohms Speaker connectors 4mm banana plugs spades connectors or naked wire Outboard power supply 20V 3A DC suitable for your country s mains supply Power consumption 3A DC lt 1W in standby Replacement battery remote control 1 x CR2032 3V or 1 x CR2025 3V Dimensions W x H x D D with sockets 206 x 40 x 150 165 mm Weight 1250g without power supply Service Should you encounter a problem which you are not able to alleviate or identify please contact your dealer for further advice Only when the problem cannot be resolved there the unit should be sent to the responsible distributor in you
3. ng the record player Connection to the speakers The output terminals accept loudspeaker cables terminated with 4mm Banana plugs spades connectors or naked wire Mains power connection The unit is supplied with a power supply suitable for your country s mains supply Check the label before connecting to ensure compliance with the mains rating in your house Connect the low voltage plug from the power supply to the Power 20V DC socket before connecting the power supply to the mains 2 Pro Ject Audio Systems gt Pro Ject Stereo Box S Phono 25 37W Revision 2014 3 4 Remote control ON OFF S turns the unit on or into standby voi and adjust the sound volume D CH and select the inputs Front panel controls 0 o 0 4 AA Stereo Box S Phono To switch on or off The toggle switch on the left hand side of the front panel turns the unit on or off Input selector After the unit is powered on pressing the push button on the right selects the IN1 to IN4 inputs one after the other The optional input expander Pro Ject Switch Box S provides three more inputs For further details please see the user guide of Pro Ject Switch Box S Volume Adjust the volume to the desired level using the large knob on the front panel Pro Ject Audio Systems Pro Ject Stereo Box S Phono 25 37W Revision 2014 3 4 3 Replacing batteries Proceed as follows e Unlock and slide open the battery case cover e Repla
4. r country Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions 5 for use Modification or change to any part of the product by unauthorized persons release the manufacturer from any liability over and above the lawful rights of the customer PRO JECT is a Registered Trademark of H Lichtenegger The information was correct at the time of going to press The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development This guide was produced by Pro Ject Audio Systems Copyright 2014 All rights reserved 4 Pro Ject Audio Systems gt Pro Ject Stereo Box S Phono 25 37W Revision 2014 3 4
Download Pdf Manuals
Related Search