Mira Platinum Wireless Controller User Guide
Contents
1. 35 MICE VIGE FC DOS e E E E 35 To Contact US cece ee eeeeeeeeeeeeeeeeeeeeeeeeeeeeees back page Introduction Thank you for purchasing a quality Mira product To enjoy the full potential of your new product please take the time to read this guide thoroughly and keep it handy for future reference The Mira Platinum Wireless Controller is a remote user interface and controls the following functions e Showering Water Temperature e Showering Water Flow e Maximum Showering Water Temperature Eco Mode e Warm Up Mode Clock Flow Range This guide covers the setting and use of these functions and includes a trouble shooting guide should the appliance not function as expected For issues relating to the installation of the appliance or other associated products please refer to the relevant Installation Guide s or contact our Customer Services Team Details in the back of this guide NOTE ALL FUNCTIONS ARE ONLY AVAILABLE AFTER THE CONTROLLER HAS BEEN ASSIGNED TO A MIRA PLATINUM DIGITAL MIXER VALVE See Mira Platinum Installation Guide 4 Safety Information 1 Make sure that you fully understand how to operate this shower and make sure that it is properly maintained in accordance with the instructions given in this manual 2 Sunburn or skin conditions can increase your sensitivity to hot water Make sure that you set the shower to a cooler temperature Control Layout Turn Ou2. Batteries Spent batteries should not be disposed of with your normal household waste Contact your local authority for information on waste disposal and recycling 32 33 Guarantee of Quality For domestic installations Mira Showers guarantee the Mira Platinum against any defect in materials or workmanship for a period of 5 years from the date of purchase shower fittings for one year provided that it is installed and maintained in accordance with the instructions given in this guide To validate the guarantee please return your completed registration card within 30 days of product installation Within the guarantee period we will resolve defects free of charge by repairing or replacing parts or modules as we may choose To be free of charge service work must only be undertaken by Mira Showers or our approved agents Service under this guarantee does not affect the expiry date of the guarantee The guarantee on any exchanged parts or product ends when the normal product guarantee period expires Not covered by this guarantee Planned maintenance or replacement parts required to comply with the servicing requirements of the TMV 2 and TMV 3 healthcare schemes where applicable Damage or defects arising from incorrect installation improper use or lack of maintenance including build up of limescale Damage or defects if the product is taken apart repaired or modified by any persons not authorised by Mira Showers or o
3. 28 Flow Range For use with High Pressure Combi Valve version only Factory default 1 99 gt Cycle menu to F 7 and press on is displayed press b to start shower gt Lower limit is displayed e g L 1 Adjust flow to desired lower limit 1 99 gt Press A to set lower limit gt Higher limit is displayed e g H 23 Adjust flow to desired higher limit 1 99 Most plumbing systems may achieve maximum flow before 99 gt Press W to set higher limit 24 Press amp to set and exit back to Function Menu See section Exit the Function Menu 25 Control Frequency Factory default 1 gt Cycle menu to F 8 and press O b gt Press or to change channel 1 6 gt Press to set Press A to exit back to Function Menu See section Exit the Function Menu 26 Replacing the Batteries To access the batteries the control unit must be removed from the wall Make sure control unit is dry before removing Bo Press button to release and remove control from wall Turn unit over to access batteries Remove and replace all batteries Only use new batteries of same make and type Do not use rechargeable batteries Note When batteries are replaced control unit activates Clock Setting mode Reset the time and press O Hook control on top of bracket and pu
4. by setting a low point and a high point During adjustment the shower will need to be started F8 Control Frequency An unreliable functioning of the appliance not always able to change settings of shower may indicate radio interference by another device transmitting locally on same channel Changing channel may resolve this problem 13 Function Menu Enter the Function Menu P gt Press and O buttons simultaneously until End is displayed on the unit gt Use or buttons to cycle through functions and press to enter setting See following sections in this guide for details on each function and how to alter their settings Note If signal loss occurs during a function change Err will appear on display Press b to clear and retry function change 14 Exit the Function Menu gt When finished use or buttons to cycle back through functions until End appears Press to exit gt Control is ready to use gt If necessary test shower to see if functions are working as expected 15 Changing Functions Settings Maximum Showering Water Temperature Factory default 45 C gt Cycle menu to F 1 and press O Press or to adjust temperature Maximum 48 C Minimum 35 C gt Press to set Press to exit back to Function Menu See section Exit the Function Me
5. d by a banker s card 35 To Contact Us England Scotland Wales and Northern Ireland Mira Showers Customer Services Telephone 0844 571 5000 E mail technical mirashowers com Fax 01242 282595 By Post Cromwell Road Cheltenham Gloucestershire GL52 5EP Eire Modern Plant Ltd Dublin Telephone 01 459 1344 E mail sales modernplant ie Fax Dublin 01 459 2329 Post Otter House Naas Road Clondalkin Dublin 22 Mira is a registered trade mark of Kohler Mira mira Limited mm SHOWERS The company reserves the right to alter product specifications without notice www mirashowers co uk 1105041 W2 B N86A 1666 Kohler Mira Ltd September 2009 plumbworia Big brands small prices Pdf Supplied By http www plumbworld co uk
6. mira Platinum Mira Platinum Wireless Controller User Guide Contents MTR OU CU OW PR e RE ERR ARARIPE e E ut 4 Safety IMOMANO Nasa ii das di 5 CONTO layout rerien nE 6 Display symbols s s sssssnsssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nn nn nn ann 7 Using the Shower s ssssssssssssssssrnrnnnnnnnnnnnnnnnnnnn renen enn nn enn nn ann 8 NU OM RR PRADA ROD RS E SD RS 8 Adjust Temperature cccecececeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 10 AUSE OWN sect oes ete RE E 11 FUNCIONS ccc s nsssp skansssskpkpsonskrkAkensskssnsss sk srKskSnAKARSSEERSRANSK RES 12 FUNCUON Menu sessirnir 14 Enter the Function Menu ss sse eee eee eee eee 14 Exit the Function Menu sese eee eee eee eee 15 Changing Functions Settings sssssssssooo 16 Maximum showering water temperature 16 EG 17 WAM e 18 Glock Se UNG esea ken Nesse EERE 19 CHOCK HISTOR Sa 21 R lt o p 11 o NO sssrinin inaa 23 2 FOW NS qse sr 24 Control FIOQUENCV unas siiniaan ias nina und sida iu pi rr nn rann 26 Replacing the Batteries sn 27 Fault STs La sena sanisr s A ER AE 28 Enor CODES sas ne er eter ne Eno Sosa Da ae er ene 28 Error During Function Change sees eee ee 29 General FAM Sic ta seene 30 cg D 32 Disposal and Recycling vscssysscsngatassssssdsssssvgssstssgreayssssssss 32 Guarantee of Quality jie 34 What to do if something goes wrong
7. nu 16 Eco Factory default off gt Cycle menu to F 2 and press ly Press or to change setting on or off gt Press tb to exit back to Function T k Menu See section Exit the Function Menu 17 Warm Up Factory default off Note Function will not work with combination boilers gt Cycle menu to F 3 and press NUN E Press or to change setting on or off gt Press W to set P gt Press to exit back to Function Menu See section Exit the Function Menu 18 Clock Setting Factory default 10 43 Note Can also be activated by disconnecting and reconnecting battery gt Cycle menu to F 4 and press a Press to change hour setting Press to change minute setting 19 Press 4 to set time and exit back to Function Menu See section Exit the Function Menu 20 Clock Display Factory default on gt Cycle menu to F 5 and press D Press or to change setting on or off gt Press 0 to set 21 E Press to exit back to Function Menu See section Exit the Function Menu 22 Calibration No e This setting is protected and for use by Service Engineer only Any alteration may result in a loss of showering performance
8. r malfunction Showerhead blocked Hose blocked or twisted Check water supply Check electrical supply Reset and recommission Replace batteries Isolate electrical supply and reset after 30 seconds If problem persists contact our Customer Services Team Check and clean Check and clean or release twist cont Malfunction Drip from showerhead Shower not hot enough Digital Mixer malfunction A small amount of water may be retained in showerhead after showering This may drain over a few minutes Maximum showering temperature set too low Digital Mixer fitted incorrectly 31 Contact our Customer Services Team This is normal Changing position of showerhead may vary draining time Increase maximum showering temperature Function F1 Make sure hot and cold water supplies are connected correctly If problem persists contact our Customer Services Team Cleaning Many household cleaners contain abrasives and chemical substances and should not be used for cleaning chrome plated or plastic fittings These finishes should be cleaned with a mild washing up detergent or soap solution and then wiped dry using a soft cloth Disposal and Recycling End of Product Life When the appliance has reached the end of its serviceable life it should be disposed ofin a safe manner and in accordance with current local authority recycling or waste disposal policy
9. sh firmly until control clicks back into place If necessary test shower to see if functions are working as expected 21 Fault Diagnosis Error Codes Aspecific problem relating to the electronic function of the shower will result in an error code being displayed on the control Over Temperature at Control Sensor 1 Turn Digital Mixer off for 10 seconds Turn back on and allow 10 seconds to reset 2 Make sure hot and cold inlets are not reversed 3 Make sure inlet filters and check valve cartridges are clean 4 If problem still occurs make a note of the error code and contact our Customer Services Team Error Code Number Not Previously Described Digital Mixer Error 1 Turn Digital Mixer off for 10 seconds Turn back on and allow 10 seconds to reset 2 If problem still occurs make a note of the error code and contact our Customer Services Team 28 Replace batteries Control out of range Error During Function Change Displayed if there is a signal loss between the Wireless Control Unit and the Digital Mixer whilst a function setting is being altered Press A to clear the display and retry the function change 29 General Faults Malfunction Shower will not operate No flow or low flow from Shower Fittings Water supply isolated Electrical supply isolated or fuse blown No connection to Digital Mixer Control out of range Flat batteries Digital Mixe
10. ter Ring Showering Water Flow Adjustment Decrease Increase Flow Flow Decrease Increase Temperature Temperature Start Stop Display Display Symbols Low Battery Display Economy Flow Display cal Temperature Display peared ow Display Control Out Of Range Clock Display Using the Shower Switch on off i Press amp to start or stop shower Temperature and flow settings will be same as when last used After a short period display will dim to help extend battery life Approximately 10 minutes after shower has stopped display will turn off automatically Shower will not run continuously for more than 30 minutes before stopping automatically 5 minutes when ECO function is set to on When Warm Up function is on there will be a short delay 5 seconds before water flows from shower Adjust Temperature gt While shower is running press or to adjust temperature Showering temperature appears on display in degrees Celsius C Adjust Flow gt Turn outer ring clockwise or anticlockwise to adjust flow Showering flow level appears on display in white bars 11 Functions The following functions can be altered individually to adjust how the shower operates F1 Maximum Showering Water Temperature This is the temperature the shower cannot go beyond when in use F2 Eco The shower will stop automatically after 5 minutes When
11. this setting is on maximum available showering flow is limited to half the flow normally produced ECO symbol is displayed When setting is off maximum showering flow will be at full flow ECO symbol goes out when more than half flow is selected F3 Warm Up When this setting is on and the shower is started there is a short delay 5 seconds before water flows and temperature display will flash to indicate shower is waiting for selected display temperature to be achieved When shower stops temperature has been reached and shower is ready for use press O as normal If temperature cannot be found shower will stop automatically after 5 minutes 12 When Warm Up setting is off temperature display will not flash and shower operates as normal Note When used with some combination boilers the warm up function may be impaired This is due to the functional nature of combination boilers F4 Clock Setting To set the time F5 Clock Display When Clock Display is on time is displayed Ter when shower has stopped or after 10 LA E E seconds of inactivity whilstthe shower Tiong is running When Clock Display is off the time is replaced by the showering temperature on off 1 11 F6 Calibration Number F7 Flow Range For use with High Pressure Combi Valve version only The water flow rate Showering force can be adjusted to within a desired range
12. ur approved agents This guarantee is in addition to your statutory and other legal rights 34 What to do if something goes wrong If when you first use your shower it doesn t function correctly first contact your installer to check that installation and commissioning are satisfactory and in accordance with the instructions in this manual We are on hand to offer you or your installer any advice you may need Should this not resolve the difficulty simply contact our Customer Services Team who will give every assistance and if necessary arrange for our service engineer to visit If the performance of your shower declines consult this manual to see whether simple home maintenance is required Please call our Customer Services Team to talk the difficulty through request a service under guarantee if applicable or take advantage of our comprehensive After Sales service As part of our quality and training programme calls may be recorded or monitored Our Customer Services Team is comprehensively trained to provide every assistance you may need help and advice spare parts or a service visit Service Repairs Our Service Force is available to provide a quality service at a reasonable cost You will have the assurance of a Mira trained engineer agent genuine Mira spare parts and a 12 month guarantee on the repair Payment should be made directly to the engineer agent who willaccept most major Credit or Debit cards or a cheque supporte
Download Pdf Manuals
Related Search