Home

Hyperfor User Guide

image

Contents

1. 77 Fix all the rack elements to the gate making sure that they stand 1 the motor must be on a levelled surface and perfectly parallel at the same height than the motor pinion to the gate 2 the distance between pinion and rack must be 1 or 2 mm The rack MUST BE positioned 2 mm over the pinion of the motor If needed adjust the 4 grains all the gate length 3 the rack must be trued up with the pinion of the motor 4 the minimum distance between the maximum overall of the gate and the case of the pinion of the motor must be of at 1 BAS mm Check the above indicated conditions and proceed fixing the 4 bolts D anchoring the motor to the plate va UO TT ci A m m eee PS aA 7 gt 5 mm a an om ei mn LLLI D INSTALLING THE MECHANICAL LIMIT SWITCHES Install limit switches on the rack and fix them using the screws provided in the tool kit AN ATTENTION check that the limit switch bracket will work effectively on the limit switch spring of the motor If necessary add thickness between the lower part of the rack and the limit switch bracket in order to keep to the measurement as stated in the figure ooo AND IORQUE LIMITING DEVICE In the absence of power the gate can be released by operating on the motor 1 Open the rear hatch 2 Loosen the allen screw L by using the equipped 4 mm al
2. OBSERVE EUROPEAN REGULATIONS 12445 AND EN12453 WHICH REPLACE UNI 8612 Always check the following e Your gate should have a strong and suitable build no wickets should be present on the sliding gate e The sliding gate should not tilt excessively during its entire run e The gate should be able to slide freely on its guiding surface without an excessive friction e Install both closing and opening limit switches in order to prevent the gate going off the guiding surface e Remove any manual locks e Bring power cable ducts near the bottom of the gate diameter 20 30 mm and of the external devices photocells flasher key selector POSITIONING OF THE MOTOR To fix HYPERFOR follow the instructions below 1 use the measurements indicated in the drawing for the foundations 50 mm 323 mm 565 mm 20 mm 2 Arrange for one or two pipes for the passage of electric cables 3 Assemble the 4 clamps on the anchoring plate and fix them with the 4 bolts issued with the motor levelled surface and parallel to the gate Wait for the complete setting of the concrete Unscrew the bolts fixing the base to the clamps and put the motor on the plate Adjust the 4 grains F to make the motor be perfectly levelled Control that the motor is perfectly parallel to the gate then insert the 4 washers R and lightly screw the 4 bolts D zIBPIE TOY ee See did Mp Aaa
3. V2 S p A Corso Principi di Piemonte 65 67 12035 RACCONIGI CN ITALY tel 39 01 72 81 24 11 fax 39 01 72 84 050 info v2home com www v2home com IL n 311 1 EDIZ 01 10 2008 HYPERFOR ATTUATORE ELETTROMECCANICO TRIFASE PER CANCELLI SCORREVOLI FINO A 4000 KG DI PESO ELECTROMECHANICAL THREE PHASE ACTUATOR FOR SLIDING GATES OF UP TO 4000 KG OF WEIGHT ACTIONNEUR LECTROM CANIQUE TRIPHAS POUR PORTAILS COULISSANTS JUSQU A 4000 KG ACTUADOR ELECTROMEC NICO TRIF SICO PARA CANCELAS DESLIZABLES HASTA DE 4000 KG DE PESO 629 mm 323 mm 290 mm 565 mm any installation problems please contact V2 S p A TEL 439 01 72 81 24 11 V2 S p A has the right to modify the product without previous notice it also declines any responsibility to damage or injury to people or things caused by improper use or wrong installation AN Please read this instruction manual very carefull before installing and programming your control unit e This instruction manual is only for qualified technicians who specialize in installations and automations e The contents of this instruction manual do not concern the end user e Every programming and or every maintenance service should be done only by qualified technicians AUTOMATION MUST BE IMPLEMENTED IN COMPLIANCE WITH THE EUROPEAN REGULATIONS IN FORCE EN 60204 1 Machinery safety electrical equipment of machines part 1 general rules EN 12445 Safe use of
4. automated locking devices test methods EN 12453 Safe use of automated locking devices requirements e The installer must provide for a device es magnetotermical switch ensuring the omnipolar sectioning of the equipment from the power supply The standards require a separation of the contacts of at least 3 mm in each pole EN 60335 1 e The plastic case has an 55 insulation to connect flexible or rigid pipes use pipefittings having the same insulation level e Installation requires mechanical and electrical skills therefore it shall be carried out by qualified personnel only who can issue the Compliance Certificate concerning the whole installation Machine Directive 98 37 EEC Annex IIA e he automated vehicular gates shall comply with the following rules EN 12453 EN 12445 EN 12978 as well as any local rule in force e Also the automation upstream electric system shall comply with the laws and rules in force and be carried out workmanlike e The door thrust force adjustment shall be measured by means of a proper tool and adjusted according to the max limits which EN 12453 allows e We recommend to make use of an emergency button to be installed by the automation connected to the control unit STOP input so that the gate may be immediately stopped in case of danger e The appliance is not to be used by children or persons with reduced physical sensory or mental capabilities or lack of experience and k
5. len spanner 3 Screw anticlockwise left thread the metal ring K using the equipped 19 mm spanner NOTE operating on the metal ring it is possible to set the built in torque limiting device Totally closed metal ring torque 0 Nm motor released Totally open metal ring torque 220 Nm To restart the automation proceed as follows 1 Screw clockwise the bolt K 2 Tighten the allen screw L 3 Close the rear hatch INSTALLATION LAYOUT Q Power supply cable 4 x 1 5 mm Q Internal Photocellules Blinker cable 2 x 1 5 Q External Photocellules cable 4 x 0 5 mm RX cable 2 x 0 5 mm TX Q External Aerial cable RG 58 Digital or key selector cable 3 x 0 5 mm Safety edge EN 12978 aSIPLE HSITDN4A
6. nowledge unless they have been given supervision or instruction e Children being supervised do not play with the appliance which can be consulted at the following web site www v2home com CONFORMITY TO REGULATIONS V2 S p A declares that the series of HYPERFOR actuators are in conformity with the provisions of the following EC directives 2006 95 CEE low voltage 89 336 CEE electromagnetic compatibility 99 05 CEE radio directive 98 37 CEE machine directive and with the standards referenced here below EN 60335 1 EN 60335 2 103 61000 2 3 EN 61000 3 3 50336 55014 1 EN 55014 2 EN 301 489 3 300 220 3 Note Declares that the above mentioned devices may not be operated until the machine automated gate is identified CE labeled and declared to be compliant to the specifications of Directive 89 392 EEC and following modifications The person in charge for the machine start up must provide the following records e Technical specification paper Declaration of conformity CE labeling Testing record Maintenance record Operation manual and directions Racconigi 20 06 2007 representative agna A Livio aSIPLE Gate maximum weight 4000 Kg 400 VAC 50Hz collegamento a stella Power supply 230 VAC 50Hz collegamento a triangolo ww Duty cicle ambient temperature 55 C ENGLISH 5 5 CAREFULLY

Download Pdf Manuals

image

Related Search

Related Contents

ダウンロード 取扱説明書 ハイパワー電動バリカン DKP-0336  7200    Beyond the Belt - Oaklandish Design  Blues 2003 User Manual  User Manual - Comkit Online  APRA manual - PerfectFlite  ダウンロードはこちらから - 一般財団法人日本自転車普及協会  ダウンロード - iceGUARD  Autour de la Petite enfance - Médiathèque - Saint-Quentin-en  

Copyright © All rights reserved.
DMCA: DMCA_mwitty#outlook.com.