V-044LW User Guide
Contents
1. kerosene etc or use in the presence of explosive liquids or vapours 13 Do not vacuum up harmful or toxic material chlorine bleach ammonia drain cleaner etc 14 Do not vacuum up hard or sharp objects such as glass nails screws coins etc 15 Do not use without the filters in place 16 Use extra care when vacuuming on stairs 17 Keep vacuuming area well lit Safety Information 18 Store the vacuum cleaner indoors in a cool dry area 19 Turn off the switch before unplugging 20 Use only CE approved 13 amp extension cords Non approved extension cords may overheat Care should be taken to arrange the cord so that the cord cannot be pulled or tripped over 21 Do not use the vacuum to pick up builders rubble sand plaster dust etc 22 This vacuum is designed for domestic use only Industrial or commercial use invalidates the warranty WARNING Always switch off and unplug the vacuum cleaner from the electrical outlet before assembling opening or emptying the dirt container or before connecting disconnecting the attachments AN CAUTION The vacuum cleaner is a very powerful unit Before plugging the cord into the outlet make sure the switch is in the off position Hold the vacuum cleaner firmly when starting and in use IMPORTANT If the vacuum inlet or hose is blocked switch off the vacuum cleaner and remove the blockage s before re starting the vacuum cleaner IMPORTANT Cleaning filters imp2. lukewarm water max 40 C e Do not use strong detergents e Ensure that the dirt container is fully dry before putting back on the vacuum cleaner Do not wash in dishwasher Maintenance 8 Maintenance Cleaning and Changing the Belt Tools required Phillips screwdriver WARNING To reduce the risk of electric shock the power cord must be disconnected before removing the dirt container HEPA filter changing the filters or performing maintenance troubleshooting checks Occasionally the power nozzle drive belt will require changing the frequency will depend upon the amount of vacuum use 1 Turn vacuum off and unplug from power supply Press handle release button and lay vacuum cleaner on a flat level surface 2 Using a Philips screwdriver remove the five 5 screws on the underside of the cleaner and remove the carpet height adjuster on the top side to release the top cover of the vacuum head Fig 8 1 3 Lift the right side of the brushbar and lift the left hand side and remove the brushbar from the power head Fig 8 2 4 Remove the worn or broken belt from the motor drive shaft 5 Carefully remove any belt residue that may exist in the belt area before replacing with a new belt 6 Loop the new belt first over the motor drive shaft and then over the agitator pulley 7 Insert the right side of the brushbar in first by placing the end cap down in the slot and then so the same with the left side
3. release button and lift away from the vacuum cleaner Fig 7 1 Cleaning the HEPA Filter Remove the dirt container lid by grasping the dirt container and turning anti clockwise Fig 7 2 Empty all the dirt from the container Remove the filter by twisting anti clockwise and pulling out Firmly tap clean the HEPA filter until no more dust is observed falling out Fig 7 3 Dirt Container amp Filter The HEPA filter may be washed by running it under the tap We recommend washing it once a month or when suction appears reduced Always allow to air dry for 24 hours before replacing into the vacuum PLEASE NOTE The white material in the HEPA filter will discolour over time This is NORMAL and will NOT affect the performance of the filter WARNING Always empty the dirt container and clean the HEPA filter before each use and during prolonged usage Never over fill the dirt container remove dirt and clean the HEPA filter each time the dirt container is emptied during prolonged usage or risk motor damage Cleaning the Pre Motor Filter Underneath the dirt container is a pre motor filter If found to be defective please replace Fig 7 4 Cleaning the Dirt Container WARNING To reduce the risk of electric shock the power cord must be disconnected before removing the dirt container HEPA filter changing the filters or performing maintenance or troubleshooting checks e The dirt container can be washed in
4. Carpet Height Adjuster The front of the vacuum cleaner has a carpet height adjuster that raises and lowers the brushbar to suit the type of carpet With the cleaner NOT connected to the electrical outlet set the adjustment to the lowest setting for maximum cleaning If the cleaner is difficult to move push the knob to the next highest setting until the vacuum is comfortable to push The brushbar must reach the carpet for effective cleaning Fig 6 3 IMPORTANT When the vacuum cleaner is stood in the upright position or when using the hose and tools the carpet height adjuster must be set to the highest position WARNING To avoid injury keep loose clothing hair fingers and all other parts of the body away from any moving part such as the brushbar Turn off the switch and unplug the cleaner before adjusting the cleaner for the carpet height Attaching the Accessories The accessories can be used with or without the exnsion tube To attach remove the hose from the machine and push the desired accessory onto the end Fig 6 4 Crevice Tool Use the crevice tool for radiators crevices corners skirting boards and between cushions 7 Dirt Container amp Filter Removal and Replacement IMPORTANT Always unplug the unit from the electrical outlet before opening the dirt container IMPORTANT Do NOT use the vacuum without the HEPA filter in place To remove the dirt container press the dirt container
5. LJA TM UPRIGHT VACUUM CLEANER Model JMU4010 User Instruction Guide Guarantee Technical Specification 1 Guarantee This product is guaranteed for 1 year from the date of original purchase If any defect arises due to faulty materials or workmanship the unit will either be repaired replaced or refunded at our discretion The following conditions apply The product must be returned to the retailer with original proof of purchase The product must be installed and used in accordance with the instructions contained in this user instruction guide It must be used only for domestic purposes It does not cover wear and tear damage misuse or consumable parts The supplier has no responsibility for incidental or consequential loss or damage Valid in the UK amp Eire only Valid only if purchased from the LWSD Group LWSD Group Box MPRC8 L70 1AB JMB Vacuum Helpline Please Call 01733 404703 JMB Vacuum Spare Pars Please Call 01733 404709 Calling from outside the UK Please Call 00 44 1733 404703 2 Technical Specification Power supply 220V 240V AC 50Hz Power Consumption 1500W Max Model number JMU4010 Protection Class Il CE 3 Safety Information FOR HOUSEHOLD USE ONLY When using the vacuum cleaner basic safety precautions should always be observed including the following 1 Only use the vacuum cleaner indoors on dry surfaces 2 Turn of
6. Press firmly to make sure that each end is completely inserted 8 Check to make sure that the belt is centred on the agitator pulley and that the brushbar turns 9 Replace the vacuum head cover by screwing in the four 4 screws on the underside of the vacuum cleaner Troubleshooting 9 Troubleshooting A WARNING To reduce risk of personal injury unplug vacuum cleaner before servicing PROBLEM Cleaner won t run Cause Not properly plugged into electrical outlet Solution Plug cord in firmly Cause No electricity in wall outlet Solution Check fuse or breaker Cause On off switch not turned on Solution Push on off switch to on Cause Motor thermostat tripped Solution Reset motor thermostat see page 3 Cause Blown fuse tripped breaker Solution Reset circuit breaker or replace fuse PROBLEM Cleaner won t pick up Cause Full or clogged dirt container Solution Clean dirt container Cause Wrong pile height setting Solution Adjust setting on carpet height adjuster Cause Clogged nozzle Solution Remove obstruction Cause Clogged dirt inlet Solution Remove power head cover and remove obstruction Cause Clogged hose Solution Remove obstruction Cause Broken belt Solution Replace belt Cause Hose not inserted fully Solution Push hose in securely Cause Dirty filters Solution Clean change filters PROBLEM Accessories won t pick up Cause Accessories
7. f the vacuum cleaner controls before connecting to or disconnecting from the mains supply 3 Always unplug the vacuum cleaner before connecting or disconnecting the vacuum hose 4 Use only as described in this manual Use only the manufacturer s recommended attachments 5 Close attention is necessary when used by or near children Do not allow children to use as a toy 6 Do not use the vacuum cleaner with a damaged cord or plug Do not use the vacuum cleaner if it has been dropped damaged left outdoors or dropped into water Return the vacuum cleaner to a Vax Authorised Service Agent or suitably qualified person for examination repair or adjustment 7 Do not pull or carry by the cord Do not use the cord as a handle close a door on the cord or pull the cord around sharp edges or corners Do not run the vacuum cleaner over the cord Keep the cord away from heated surfaces 8 Do not handle the plug or vacuum cleaner with wet hands Do not use outdoors or on wet surfaces 9 Do not put any objects into openings Do not use with any openings blocked and do not restrict air flow Keep all openings free of dust lint hair or anything that may reduce airflow 10 Keep hair loose clothing fingers and all parts of the body away from openings and moving parts 11 Do not pick up hot coals cigarette butts matches or any hot smoking or burning objects 12 Do not pick up flammable or combustible materials lighter fluid petrol
8. hold waste The Waste Electrical and Electrical Equipment WEEE Directive has been introduced across the European Union e to recycle waste electrical products using the best available recovery and recycling techniques in order to minimise the impact on the environment e to treat any hazardous substances and e to avoid increasing landfill WEEE product should be disposed of by handing it over at a designated collection point For more information about where you can drop off your waste product for recycling please contact your local authority Recycling 11
9. not attached correctly Solution Refer to section 5 for fitting information PROBLEM Cleaner picks up moveable rugs or pushes too hard Cause Wrong pile height setting Solution Adjust setting on carpet height adjuster PROBLEM Brushbar does not turn Cause Broken belt Solution Replace belt Cause Belt installed incorrectly Solution Check belt PROBLEM Air flow restricted with attachment use Cause Attachment use restricts air flow Solution Check attachment Cause New carpet debris clogging air path Solution Remove obstruction Service 10 Service e Ifthe power cord has been damaged in any way do not use the vacuum cleaner The vacuum cleaner must be repaired by a qualified service agent e f you have any technical problems with your vacuum cleaner please call the JMB helpline 01733 404703 JMB Vacuum Helpline Please Call 01733 404703 JMB Vacuum Spare Parts Please Call 01733 404709 Calling from outside the UK Please Call 00 44 1733 404703 10 11 Spare Parts List JMU4010 01 JMU4010 02 JMU4010 03 JMU4010 04 JMU4010 05 JMU4010 06 JMU4010 07 JMU4010 51 Hose Drive Belt Beater Bar Dust bin and lid Crevice Tool Extension Tube Handle Filter Kit 12 Waste Electrical Recycling XX This symbol indicates that this product is classed as Electrical or Electronic Equipment and should not be disposed of with other house
10. roves vacuum performance Make sure all filters are replaced back into the vacuum cleaner before using IMPORTANT The motor is equipped with a thermal cut out If for any reason the vacuum cleaner should over heat the thermostat will automatically turn the unit off Should this occur unplug the vacuum cleaner from the electrical outlet and turn off the switch Remove the dirt container and empty Clean the filters Allow the cleaner to cool for approximately one 1 hour To re start plug into the electrical outlet and switch back on This vacuum cleaner is intended for household use only and not for commercial or industrial use PLEASE KEEP THESE INSTRUCTIONS FOR FURTHER USE electrical Safety 4 Electrical Safety Before switching on make sure that the voltage of your electricity supply is the same as that indicated on the rating plate This product is designed to operate on 220 240V AC 50Hz Connection to any other power source may damage the unit This product may be fitted with a non rewireable plug If it is necessary to change the fuse in the plug the fuse cover must be refitted f the fuse cover becomes lost or damaged the plug must not be used until a suitable replacement obtained f the plug has to be changed because it is not suitable for your socket or becomes damaged in any way it should be cut off and an appropriate plug fitted following the wiring instructions below This should be carried ou
11. serting the two long screws Fig 5 2 Assembling the Dirt Container 3 Insert the bottom of the dirt container to align with the tab on the upper cover of the motor To secure the dirt container push the top in place there will be an audible click when it is secure Fig 5 3 Assembly Assembly of the Hose 4 Align the tabs on the lower hose inspection tube with the slots on the hose Push and turn the hose clockwise until secure Fig 5 4 K AA ANN 5 Wrap the hose round and through the hose clip and then down and insert into hose connector Fig 5 5 Cord Storage This vacuum cleaner is equipped with a convenient cord storage feature The power cord winds around the two cord holders at the side of the unit The bottom cord holder has a quick release feature Turn the cord hook to the left or the right to remove the power cord Fig 5 6 Operation 6 Operation 1 Turn the vacuum cleaner on by pressing the on off switch located on the lower right side of the cleaner Fig 6 1 The cleaner can be turned off by pressing the on off switch again On off switch Fig 6 1 i AN Y Adjusting the Angle of the Main Body 2 To adjust the angle of the vacuum cleaner body push the release pedal on the lower left side of the cleaner Fig 6 2 3 Move the handle to the desired position A for upright position B for normal operation and C to clean under furniture Fig 6 2
12. t by a qualified electrician The plug removed must be disposed of safely as insertion into a 13 Amp socket is likely to cause an electrical hazard IMPORTANT THIS IS A CLASS II APPLIANCE AND DOES NOT REQUIRE AN EARTH CONNECTION Wiring Instructions The wires in this mains lead are colored in accordance with the following code Blue Neutral Brown Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows refer to the plug wiring diagram BLUE e The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured Black e The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured Red If a 13Amp BS1363 plug is used a 13Amp BS1362 fuse must be fitted or if any other type of plug is used a 13Amp fuse must be fitted either in the plug or adaptor or on the Distribution Board 5 Assembly IMPORTANT Always remove the power plug from the electrical outlet before assembling or removing accessories Handle Assembly 1 Firmly push the back panel onto the base assembly Ensure it is fully located before inserting the two short screws Fig 5 1 Fig 5 1 f I UN AT 2 Slide the handle into place onto the top of the back panel Secure the top handle to the back panel by in
Download Pdf Manuals
Related Search