i.Tech Arrow Lite User Guide i.Tech Arrow Lite
Contents
1. damage to your hearing please do not set the listening volume too high Never use the headset while taking a bath Do not use the headset in a sauna or steam room Do not keep your headset near a wash basin or other wet places Do not use the headset outdoors in the rain Do not clean the headset while it is being charged Always unplug the charger first before cleaning the headset Do not attempt to modify the headset for other purpose Do not attempt to force open or mutilate the built in battery Replace the earphone when it shows signs of breaking from the wire Disposal of the packaging and the headset should be done in accordance with the local regulations Troubleshooting If you are unable to connect your headset and mobile phone please try the following Ensure your the battery is fully charged Turn off your headset and then turn it on again Ensure the headset is paired with your mobile phone Ensure your mobile phone s Bluetooth function is activated For some phone models a headset icon will appear on the phone s screen Please refer to your mobile phone user guide for specific instructions Ensure the headset is within 10 metres of your mobile phone and there are no obstructions such as walls or other electronic devices in between If the above suggestions do not solve your problem please recharge the headset and remove your mobile phone battery for a while Then start pairing again The i Tech Arrow Lite Bluetooth Heads2. refer to Figure 1 for two seconds to turn on the headset Please refer to Turning Your Headset On and Off for further details Talk and Standby Time A fully charged battery can offer up to 12 hours of talk time and up to 180 hours of standby time When there are no calls the headset should remain turned on in standby mode Battery Low Indication When the battery has become low when the headset is on the status indicator will flash red and the headset will emit a beep every minute Please follow the instructions described above to recharge the battery If you are pairing your headset and your mobile phone in a noisy environment we advise you to put on the earphone first so that the beep will be more audible Turning Your Headset On and Off Turning On the Headset Press and hold the MFB see Figure 1 for two seconds until you hear a short beep The status indicator will then flash blue IMPORTANT Press the MFB again when you want to turn on the headset to re activate pairing and ensure the connection between the headset and the mobile phone is resumed For pairing please refer to Pairing Your Headset on page 8 of this user guide Turning Off the Headset Press and hold the MFB for two seconds until you hear a long beep The status indicator will turn red and the headset will turn off IMPORTANT To disconnect the Bluetooth connection press the headset s MFB firmly to turn it off If you will not be using the headset for a while
3. Y TecH i Tech Arrow Lite Ss N 5S User Guide N AA Bluetooth Y TeoH i Tech Arrow Lite teercuiae i Tech Arrow Lite Overview Status Indicator This small light will flash red Built in Microphone blue or purple dependant on pairing mode and Built in Rechargeable Battery operation Ear Hook Multi function Button MFB Volume Button Charging Socket Earpiece Getting Started To use your i Tech Arrow Lite Bluetooth Headset the headset please follow the steps below 1 Ensure your headset is fully charged 2 Pair your charged headset with a Bluetooth enabled mobile phone Charging Your Headset Charging Charger Charger Pl Fig 3 mcr The headset comes with a built in rechargeable battery Prior to using the headset for the first time it is recommended to fully charge the battery first Insert the charger plug into the headset s charging socket refer to Figure 3 and plug the mains charger to an AC wall outlet The light on the Arrow Lite status indicator will stay red during charging IMPORTANT Charging indication will be delayed for a few seconds if the headset has not been used for a long time or the battery is drained Normal Charging Time It takes about three hours to fully charge the battery when the battery is fully charged the status indicator will turn blue and remain on Unplug the mains charger from the AC wall outlet and the charger plug from the headset Press and hold the MFB
4. et is compliant with and adopts the Bluetooth Specification Version 2 0 Class 2 However interoperability between the headset and other Bluetooth enabled products is not guaranteed because it depends on compatibility For more information on the compatibility between the headset with other Bluetooth enabled products please check with the respective manufacturer or visit http www itechdynamic com Product Specifications Bluetooth Specification Version 2 0 Class 2 Bluetooth Profile Supported Headset and Handsfree Range of Frequency 2 4GHz Spectrum Reception distance 10 metres Normal Charging Time Within 3 hours Talk Time Up to 12 hours Standby Time Up to 180 hours Dimensions 56 L X 20 W x 26 H mm Weight 12 5 grams may vary due to users operation mode and mobile phone settings Declaration of Conformity We i Tech Dynamic Ltd declare that the following product Product Name i Tech Arrow Lite Model No C51 A06001 XX Is in conformity with the following essential requirements of Council Directive 1999 5 EC referred to as R amp TTE Directive Article 3 1a 3 1 b and 3 2 and the product is manufactured in accordance with Annex II of above directive A copy of the Declaration of Conformity can be found at http www itechdynamic com Q ay X 10 2006 O eTOCH ae C Fe Pinted in China This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 thi
5. obile phone s main menu For certain mobile phone models once the headset is activated a headset icon will be shown on the screen You should now be able to make and receive calls using your headset IMPORTANT If the pairing cannot be completed within two minutes after the pairing mode has been activated the headset s status indicator will flash purple red accompanied by three beeps and will then turn off automatically Please repeat steps 2 to 7 above to pair the headset and the mobile phone again Using Your i Tech Arrow Lite Headset Answering a Call When there is an incoming call you will hear the ring through the earphone Press the MFB once to accept the call or answer the call via your mobile phone in the normal way Ending a Call Press the MFB once to end your call or end the call via your mobile phone in the normal way Adjusting the Volume Press the volume UP or DOWN key repeatedly until you reach the desired volume level The volume may be affected by the volume setting of the caller s phone as well Re adjust the listening volume again when necessary Call Muting During Conversation During conversation press and hold the Volume Key for 2 seconds to mute the built in microphone when the mute function is activated you will hear a short beep every 5 seconds accompanied by the headset s status indicator flashing every 5 seconds To cancel press the Volume Key for 2 seconds to deactivate the muting function whilst in conversa
6. olume key Press and hold the volume key again until the status indicator is purple The headset is reset and will resume the charging mode Note After resetting all previous pairing settings are cleared Care and Maintenance Headset Turn off your headset before placing it in your pocket or bag If the MFB is accidentally depressed your mobile phone may place an unintended call Do not expose the headset to liquid moisture or humidity as it is not waterproof Do not use abrasive cleaners to clean the headset Do not expose the headset to extremely high or low temperatures Do not leave your headset under the hot sun for a long time Do not leave your headset near open flames such as cooking burners Do not dispose of the headset in a fire as it will result in explosion Do not bring your headset into contact with any sharp objects as this will cause scratches and damage Do not stick anything inside the headset as this may damage internal components Do not attempt to disassemble the headset as it does not contain serviceable components Do not pull or drag the earphone wire with force If you will not use the headset for a long period please store it in a dry place that is free from extreme temperatures and dust Built in Battery e Do not attempt to replace the headset s battery as it is in built and is not changeable e Charge the battery in accordance with the instructions supplied with this user guide e Use only the charger supplied by
7. s device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment i Tech declares under our sole responsibility that the headset is in conformity with the provisions of the following Council Directives 1999 5 EC Dispose of the packaging and this product in accordance with the latest provisions
8. the headset s original manufacturer to charge the battery Charger e Use only the charger supplied by the headset s original manufacturer to charge the headset Other chargers may look the same but they could be dangerous Do not attempt to disassemble the charger as it may expose you to dangerous voltages or other risks Incorrect reassembly can cause electric shock when the headset is subsequently used Do not use the charger outdoors or in damp areas Only charge the headset s built in battery in accordance with the instructions described in this user guide Avoid charging the headset in extremely high or low temperatures Safety Information e Check and observe local laws regarding the use of a mobile phone and headset while driving If you use the headset while driving ensure your full attention and focus It is your responsibility to drive safely Consider to pull off the road before making or answering a call Never leave your headset above any air bag deployment area inside your car as serious injury May result when an air bag deploys Never allow children to play with the headset small parts may be of choking hazard Observe all signs and displays that require an electrical device or RF radio product to be switched off in designated areas These could include hospitals blasting areas and potentially explosive atmospheres 8 Turn off your headset prior to boarding an aircraft Do not use your headset inside an aircraft To prevent
9. tion Dialing from Your Mobile Phone Simply make calls on your mobile phone in the normal way Voice Dialing from Your Headset If your mobile phone is equipped with the voice dialing function simply press the MFB on your headset and when you hear a beep say the voice tag IMPORTANT For voice dialing you must record the voice tag the person s name into your mobile phone before using the voice dialing function on the Arrow Lite headset Please refer to your mobile phone s user guide on how to record the voice tag Last Number Redialing from Your Headset Press the MFB on your headset twice IMPORTANT The above functions are only applicable to mobile phones with Bluetooth Handsfree Profile Functionality varies depending on the mobile phone model you have Please refer to your Mobile phone user guide for additional information Rejecting a Call Handsfree Profile ONLY Press and hold the Volume Key then press the MFB key to reject the incoming call Transferring a Call Handsfree Profile ONLY Press and hold the Volume Key then press the MFB key to transfer the call from headset to your mobile handset Resetting or Removing Pairing You may reset the headset to its original settings anytime To do this you also clear all current Pairing settings Insert the charger plug into the headset s charging socket Press and hold either of the volume keys for 20 seconds until the status indicator flashes purple rapidly Release the v
10. we advise you turn off the Bluetooth function on your mobile phone as well Pairing Your Headset The headset works with Bluetooth enabled mobile phones only Prior to using and pairing your headset for the first time please check if your mobile phone is Bluetooth enabled This information will normally feature on the packaging or user guide that is provided with your mobile phone The pairing instructions for a typical Bluetooth enabled mobile phone are explained on the next page The headset pairing procedure may vary depending on the model of your mobile phone Please contact the manufacturer of your mobile phone or its agent for further information 1 Place the headset and the mobile phone where they are no more than one metre apart 2 Ensure the headset is off The status indicator is unlit and does not flash 3 Press and hold the MFB until the headset s status indicator flashes blue and red alternately 4 Activate your mobile phone s Bluetooth function Please refer to your mobile phone user guide for details Set the mobile phone to search for Bluetooth devices within the one metre range as instructed in the mobile phone user guide and select i Tech Arrow Lite from the list Enter the pre programmed passkey 0000 and press OK to pair your headset and mobile phone when the pairing is completed the headset s status indicator will flash blue rapidly for five times followed by a long beep GO back to your m
Download Pdf Manuals
Related Search