Installer and user guide for domestic reverse
Contents
1. The manufacturer reserves the right to modify product design or specific components if such modification does not entail deterioration of consumer properties of the product This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 3 CONNECTION DIAGRAMS 3 5 CONNECTION DIAGRAM FOR UNIT WITH BOOSTER PUMP AND MINERALIZING POST FILTER Black tube Models RO 6 36MP RO 6 50MP RO 6 75MP RO 6 100MP Blue tube eqni D all 27 Red tube 2S v3 The manufacturer reserves the right to modify product design or specific components if such modification does not entail deterioration of consumer properties of the product This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 14 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 3 CONNECTION DIAGRAMS 3 6A CONNECTION DIAGRAM FOR UNIT WITH ULTRAVIOLET LAMP AND MINERALIZING POST FILTER WITH SINGLE LEVER FAUCET Black tube m EN Cr eqni Models RO 7 36MUV RO 7 50MUV RO 7 75MUV RO 7 100MUV The manufacturer reserves the right to modify product design or specific components if such modification does not entail deterioration of consumer pr2. Hi Fig A1 Fig A2 Fig A3 feed water adapter m Le feed water adapter AN 4 Unscrew the compression nut from the feed valve 5 and put it on feed water adapter the red tube Push the red tube on the end of feed valve s fitting and screw on the compression nut Connect the free end of the red tube with the quick connect fitting of the first rightmost housing in the rack feed valve 8227 l PTFE tape feed valve compression nut red tube 5 Connect the drain saddle 8 with drain pipe from the kitchen sink The drain saddle is compatible with most standard drain pipes Drill a hole of 5 0 mm diameter in the kitchen sink drain pipe apply rubber gas ket with sticky base included in the package Install the drain saddle 8 on the drain pipe over the hole Tighten nuts on drain saddle with a wrench Insert black tube into the connection on the clamp figure 4 Connect the other end of the black tube with concentrate outlet of membrane housing CAUTION Check if the flow regulator 12 is installed in the black tube in the end connected to membrane housing 6 Put a few turns of PTFE tape on the thread on tank outlet Screw the tank valve tank valve onto the tank outlet Close the tank valve PREIS IMPORTANT Check air pressure in empty tank Tank should be pres P surized to 0 4 0 6 bar If n
3. PURE WATER FILTERS Installer and user guide for domestic reverse osmosis system Einbau und Bedienungsanleitung f r Umkehrsosmose Haushaltssysteme Manual privind conectarea si exploatarea sistemului de osmoza inversa Z ecosoft water professionals REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE CONTENTS 1 Purpose of the product 4 2 Specifications and components 6 2 1 Model designations 6 2 2 Specifications and requirements 7 2 3 Supply water quality requirements 7 2 4 Reverse osmosis system components 8 3 Connection Diagrams 10 3 1 Connection diagram for base model 10 3 2 Connection diagram for unit with mineralizing post filter 11 3 3 Connection diagram for unit with ultraviolet lamp 12 3 4 Connection diagram for unit with booster pump 13 3 5 Connection diagram for unit with booster pump and mineralizing post filter 14 3 6A Connection diagram for unit with ultraviolet lamp and mineralizing post filter with single lever 15 faucet 3 65 Connection diagram for unit with ultraviolet lamp and mineralizing post filter with double 19 lever faucet 3 7 Connection diagram for unit with booster pump and ultravi
4. Using chlorine disinfectant tablets is recommended for reverse osmosis filter sanitization 1 Shut off feed valve 5 and tank valve 6 2 Remove and discard the pre filter cartridges and carbon post filter 3 Unscrew cap of membrane housing and remove membrane using needlenose pliers if necessary Put the membrane into a tight bag and store in refrigerator at 2 5 4 Screw back on 2nd and 3rd pre filter sumps screw on membrane fy housing cap and connect the tube from the faucet directly to the union tee without carbon post filter al JUL This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 30 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 7 SANITIZATION OF REVERSE OSMOSIS FILTER 31 4 T E HI E Fo L f DM LP m 5 Put a chlorine tablet in the 1st sump Fill the sump with water and screw on Put a chlorine tablet 6 After 15 minutes open the drinking water faucet 3 and feed valve 5 7 When water running from the faucet 3 starts to smell like chlorine close both the faucet 3 and feed valve 5 8 Leave the system for 2 3 hours 9 Open faucet 3 and fee
5. DIAGRAMS 3 2 CONNECTION DIAGRAM FOR UNIT WITH MINERALIZING POST FILTER eqni Models RO 6 36M Red tube RO 6 50M NI ox RO 6 75M RO 6 100M The manufacturer reserves the right to modify product design or specific components if such modification does not entail deterioration of consumer properties of the product This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 3 CONNECTION DIAGRAMS 3 3 CONNECTION DIAGRAM FOR UNIT WITH ULTRAVIOLET LAMP QS y sr 220V x H 4 5 o D Models RO 6 36UV AUGE RO 6 50UV eat all RO 6 75UV RO 6 100UV The manufacturer reserves the right to modify product design or specific components if such modification does not entail deterioration of consumer properties of the product This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 12 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 13 3 CONNECTION DIAGRAMS 3 4 CONNECTION DIAGRAM FOR UNIT WITH BOOSTER PUMP eqn anig 220V H S Black tube LX 2 e E y m D i np 3 Models RO 5 36P RO 5 50P ILLA RO 5 75P Red tube RO 5 100P
6. SPECIFICATIONS AND COMPONENTS 2 1 MODEL DESIGNATIONS Models Model of your system RO 5 36 50 75 100 RO 5 36 50 75 100 P RO 6 36 50 75 100 M RO 6 36 50 75 100 MP RO 6 36 50 75 100 UV RO 6 36 50 75 100 UVP RO 7 36 50 75 100 MUV RO SEE 7 36 50 75 100 MUVP 1 23 4 1 The type of filter RO stands for reverse osmosis 2 Number of stages 3 Capacity of reverse osmosis membrane in GPD gallons per day 36GPD 136 liters per day 5 6 liters per hour 50GPD 190 liters per day 7 9 liters per hour 75GPD 280 liters per day 11 6 liters per hour 100GPD 380 liters per day 15 8 liters per hour Capacity of the reverse osmosis filter is variable and depends on a number of factors These include supply water quality wear of pre filter cartridges and of membrane itself supply water pressure and temperature 4 Legend of additional equipment no letters specify base model with no extra equipment M The filter is equipped with mineralizing post filter P The filter is equipped with pressure booster pump UV The filter is equipped with ultraviolet disinfection unit For example Ecosoft RO775MUVP means reverse osmosis unit with 7 stages equipped with membrane of 75 gallon per day capacity 11 6 h mineralizing post filter UV lamp and booster pump CAUTION Filter installation should be carried out by a specialist with appropriate qual
7. of the product may take place by any means of transport except unheated during cold seasons in colder climates in accordance with the rules of transportation of goods applicable to each type of transport Observe handling labels when handling and shipping the product Prod uct should be stored indoors with protection from mechanical damage impact of moisture and aggressive chemicals Store this product in the manufacturer s original packaging at ambient tem peratures ranging from 5 C to 40 C and relative humidity up to 80 at least 1 m away from heating equipment 13 WARRANTY We thank you for purchasing a reverse osmosis product by Ecosoft Company We hope that this product will serve you long and let you and your family enjoy high quality pure drinking water The manufacturer guarantees that the water purification system does not contain workmanship defects and no such defects will arise within warranty period from the date of pur chase from store provided that the technical requirements and operating conditions specified in this manual are strictly adhered to To avoid misunderstanding we urge you to carefully read the instructions on installation and op eration of the reverse osmosis system warranty conditions liabilities check correctness of the warranty card presence of proof of purchase receipt invoice or bill Warranty card is valid only if model date of purchase and stamp of selling establishment are correctly specifie
8. prohibited O 2014 40 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 41 This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE NOTES 42 This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014
9. sure pressure in your tank is in line with the above figures Open tank valve This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 36 37 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE ainjeusis 5 3 8 6 J9uMQ peJequnooue adUeWJOJJad s Je e3sui 3onpoad Se swej ON si pue pas sem 3onpoJd SJJOM 15 9 z g gt 8 E SE g 5 v d 88 mc o z ct o g Ss UE P vE 5 5 1 fo gt 5 5 lt 5 55 5 S st ag gt 2 2 E 5 5595 gt gt o o E 6c a Z ES c Sogan 5 2 22 2 95050 5 as Lessa x A 5 sos a a EE Ez 2 2 x gt E 2 8 8 eREGE E 2 lt T 2 gt a E TEDHA a DNINOISSIIAINOO Aue aseo y Aq paysanbas ue SIU ospy papaau 40 e ueusqureuj 3no 515 212905 djay 80 5141 ur uoneJedo 5 5 5 Jno daa A Suou1s J9Jn32ejnuelA 34 JDIAYAS 6
10. 5 to 3 hours After the tank has been filled the auto shut off valve shuts off the water supply from the pre filters and the unit stops After opening purified water faucet 3 the pressure of water in the tank lowers and the auto shut off valve automatically resumes the flow of water through the pre filter cartridges to the membrane to re fill pressure tank Water with retained impurities con centrate is discharged into drain through the concentrate outlet connected with black tube to drain saddle 8 which is installed on drain pipe In order to create backpressure which is required to maintain the operating pressure inside the membrane housing flow restrictor 14 is installed in the black tube Flow restrictor is a plastic insert with precision bore capillary The flow restrictor is inserted inside the end of black tube that is fitted in the membrane concentrate outlet When drawn from the faucet purified water runs from the pressure tank through the union tee through to the fifth stage of purification carbon post filter intended for the final purification of water It contains high quality activated carbon made from coconut shell This filter improves and refines flavor of purified water Carbon post filter is connected with blue tube to the drinking water faucet 3 mounted on sink or counter This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 2
11. 6 14 Openthe feed valve 5 This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 26 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 6 3 THE PROCEDURE FOR REPLACING MEMBRANE 27 membrane replacement should be performed by a qualified specialist 1 Turn off water supply to the system feed valve 5 shut off the tank valve 6 2 BOpen the purified water faucet 3 to relieve permeate pressure 3 Disconnect the white tube from the inlet in membrane housing cap 4 Unscrew the membrane housing cap 5 Remove the used reverse osmosis membrane 11 remember which end of the membrane goes where Membrane Cap of the membrane housin White tube 6 Lubricate rubber seals of the fresh replacement membrane and membrane housing cap sealing CAUTION To avoid damage to the membrane only use food grade glycerol as lubricant 7 Install the fresh membrane into the housing observing its direction and position of the tube CAUTION Cut the plastic bag to install the reverse osmosis membrane Install the membrane without first unpack ing it by pushing it into the housing directly from the bag Avoid touching the membrane and only hold it covered with the bag 8 Screw on the housing cap 9 Connect the white tube to the membrane housing inlet 10 Close drinking water faucet 3 11 Open the tank valve 6 12 Open the feed valv
12. Clean or replace flow restrictor Drain saddle fitting is not centered on drain pipe hole Correctly position the drain saddle This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 8 TROUBLESHOOTING Drinking water has a milky or cloudy appearance that goes away after a few minutes Air in the system Some air in the system is normal for a few days after the system was installed In some cases air bubbles may appear due to supply water being significantly lower temperature than your home s ambient temperature Water has a taste and or odor Carbon post filter has expired Replace the post filter Preservative solution in the membrane has not been flushed out Drain all the water from the tank and let the system re fill it Contamination in reverse osmosis system Sanitize the system per instructions in section 7 Contamination in pressure tank Replace the tank or sanitize per instructions in paragraph 7 1 Pressure tank holds too little water Tank bladder is overpressurized Pressure in empty tank should be 0 4 0 6 bar 6 9 psi Make sure pressure in your tank is in line with the above figures No water is dispensed from faucet albeit tank is full Tank bladder is underpressurized Tank valve is closed Pressure in empty tank should be 0 4 0 6 bar 6 9 psi Make
13. QUALITY REQUIREMENTS Index VALUE 1 6 5 8 5 2 TDS 1500 ppm 3 Hardness 500 ppm CaCOs 28 dH 4 Free chlorine 0 5 ppm 5 lron 0 3 ppm 6 Manganese 0 1 ppm 7 Chemical oxygen demand 5 ppm O2 8 Total bacterial count TBC 50 CFU mL 9 E coli titer lt 3 f water supply does not meet the requirements service life of membrane and or pre filter cartridges may be shortened If your home is supplied with raw wellwater perform laboratory test of your water before installing a reverse osmo sis filter If any of your water indices exceed the limit consider using a water treatment system to correct supply water quality Refer to water treatment specialists or companies for advice and proper equipment selection This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 2 SPECIFICATIONS AND COMPONENTS 2 4 REVERSE OSMOSIS SYSTEM COMPONENTS The manufacturer reserves the right to modify product design or specific components if such modification does not entail deterioration of consumer properties of the product 1 Filter rack carbon post filter auto shut off valve membrane housing filter head Options mineralizing post filter and or other type of post filter booster pump This manual is the intellectual property of Ecosoft Copying and
14. This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE Type of job Consumables used for the job product date of manufacture serial number example cartridges membrane Sanitization performed YES NO Tank fill duration HH MM Recovery 6 MAINTENANCE LOG Recommendations Date of maintenance DD MM YY Servicing company name cc e gt a N o Installer s name Servicing company contact information Signature This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 10 ENVIRONMENTAL AND HEALTH SAFETY The product does not have any chemical radiological electrochemical impact on the environment The product is not regarded as hazardous by their impact on the human body meets requirements of relevant sanitary legislation for its intended scope of use 11 PURCHASING Desirably the product should be purchased from authorized sales establishments When buying check integrity of packaging absence of mechanical damage and other defects contents of the system without opening the plastic bags availability of user documentation particularly this manual and warranty card 12 TRANSPORTATION AND STORAGE Shipping
15. d For proper installation details please read instructions on how to install and use or seek help from a qualified professional The manufacturer is not liable for any damage to property or some other damage including lost profits which arose by chance or due to use or inability to use this product Manufacturer s liabil ity in accordance with this warranty is limited to the cost of the filter This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE The warranty does not cover replaceable elements cartridges reverse osmosis membrane carbon post filter mineralizing post filter or other consumables included in the package electrical equipment in ungrounded electrical systems or lack of voltage regulator where it is required components that require replacement because of normal wear and tear faults and problems that have arisen due to untimely replacement of consumable elements where there intervals are provided in this manual and also due to use of other manufacturers consumables All claims related to taste smell and other quality indicators of water purified by this system should only be filed with a water test report issued by an accredited laboratory Cases not covered under this warranty shall be resolved in accordance with local legislation This manual is the intellectual property of Ecosoft Copying and reprinting is
16. d that the yellow tube s length is sufficient to connect it to the rest of the system 4 Install the system per the guidelines of this manual 4 2 INSTALLATION PROCEDURE CAUTION This system has been tested by the manufacturer for leaks so within the system the presence of residual water is allowed Wash your hands thoroughly with anti bacterial soap before handling tubes cartridges and membrane This system should desirably be installed in places protected from direct sunlight and away from heating appliances 1 Remove the reverse osmosis system from its packaging and check the equipment Do not open the bag with compo nents Note that you will not be able to claim missing parts if the bag is opened 2 Shut off water supply in your kitchen or whole home and open water tap where you are about to install the system on your kitchen sink for 1 minute to relieve pressure in the system and then close it This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 21 4 STEPS FOR INSTALLING REVERSE OSMOSIS SYSTEM 3 Screw the feed water adapter 4 into the cold water plumbing Screw the feed valve 5 into the feed water adapter 4 To help prevent water leaks use PTFE sealing tape Connections size is selected to fit most common size 7 inch pipe If your pipe is of another size prepare an appropriate adapter
17. d valve 5 and let water run until bleach odor is gone 10 Install all consumable parts back into the system Open tank valve G and feed valve 5 11 Drain the tank and re fill for at least two times until chlorine odor cannot be smelt This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 7 SANITIZATION OF REVERSE OSMOSIS FILTER 7 1 SANITIZATION OF PRESSURE TANK 1 Turn off feed valve 5 2 Open the faucet 3 and empty the pressure tank in the drain 3 Shut tank valve 6 4 Extract pre filter cartridges 5 Install 2nd and 3rd sumps by water flow direction back on filter This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 33 7 SANITIZATION OF REVERSE OSMOSIS FILTER 6 Disconnect the tube going to the storage tank from the union tee before the carbon post filter and into 3rd pre filter s outle pe 7 Put a disinfection tablet in the 1st sump Fill the sump with water and screw on 8 After 15 minutes open tank valve 6 9 Open the feed valve 5 for 5 minutes 10 Close the tank valve 6 and leave the tan
18. e 5 13 Once the tank is full you will hear the water stop flowing drain all water from the tank into the sink by opening faucet 3 When the water stops running close the purified water faucet 3 so that the tank starts to re fill Depending on the pressure in your water mains filling may take 1 5 to 3 hours After the second tank re fill you can safely use the purified water This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 6 4 THE PROCEDURE FOR REPLACING CARBON POST FILTER AND OR MINERALIZING POST FILTER 1 Turn off water supply to the system feed valve 5 shut off the tank valve 6 2 Open the purified water faucet 3 to relieve permeate pressure 3 Disconnect the tubes that connect the carbon post filter mineralizing post filter to the rest of the system remember which goes where 4 Remove the used carbon post filter mineralizing post filter from clip brackets 5 Install new carbon post filter mineralizing post filter guided by arrows that indicate the direction of water flow 6 Connect the tubes to the new carbon post filter mineralizing post fil ter to connect it to the system 7 Open feed valve 5 Open tank valve 6 9 Once the tank is full you will hear the water stop flowing drain all water from the tank into the sink by opening faucet When the water stops running close
19. e tube back to the auto shut off valve 14 Install the membrane 11 into the membrane housing CAUTION Cut the plastic bag to install the reverse osmosis membrane Install the membrane without first unpacking it by pushing it into the housing directly from the bag Avoid touching the membrane and only hold it covered with the bag 15 Leave the feed valve 5 and purified water faucet open for 30 minutes Then open the tank valve 6 Close the faucet 3 and carefully check all connections for leaks CAUTION The first week after installation check the system daily for leaks do it periodically in the future If you are leaving for a long time such as for a business trip or vacation shut off the water supply 16 After the water tank is filled you will hear the water stop flowing drain all water from the tank by opening the faucet 3 After the tank has been emptied close the faucet 3 so that the tank starts re filling Depending on the pressure in your water mains it may take 1 5 to 3 hours After the tank is filled for the second time you can use purified water This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 5 STEPS AFTER INSTALLATION VERIFICATION OF THE UNIT S OPERATING PARAMETERS 24 1 Measure time needed to fill the tank Tank is filled when the dumping of the concentrate into the drain ha
20. ecessary use a pump with a pressure gauge E i PTFE tape to increase the pressure or push the core of the valve stem to relieve pressure This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 4 STEPS FOR INSTALLING REVERSE OSMOSIS SYSTEM 7 Installation of the faucet 7 1 To install drinking water faucet drill 12 5 mm diameter hole in conve nient location at the sink or countertop Caution metal shavings can damage your unit remove them carefully as soon as you have drilled the hole If the mounting surface is ceramic or stone you may need a special carbide drill 7 2 Mount the faucet on the sink or countertop as shown on the figure Nut lock washer and plastic washer on the faucet small rubber gasket shank must fix the faucet firmly on the surface chrome plated cover 7 3 Take the blue tube put on compression nut ferrule and put large rubber gasket plastic insert inside in that order large plastic gasket 7 4 Push the blue tube as deeply as possible into the bottom of the faucet s shank ensuring the compression ring is in the ock washer joint Screw on the compression nut in order to join the tube to the faucet nut 7 5 Installation of the double lever faucet for a system with counter mineralizing post filter is done similarly pla
21. h care and only held by the ceramic ends because contaminat ing the quartz surface will reduce germicidal efficiency and shorten service life Use cotton gloves while handling UV lamps 1 Disconnect the UV lamp from the power supply 2 Shut off the feed valve 5 and tank valve 6 3 Remove the black PVC end cap with wire hole 4 Remove the lamp from the quartz sleeve by pulling on its base Do NOT touch the bulb 5 Disconnect the power connector holding the lamp by its base 6 Insert the new lamp half way into the quartz sleeve Properly connect the power connector 8 Push the new lamp all the way into the housing and put the PVC cap on its end 9 Restore the water supply to the unit and check if tightness of quartz sleeve sealing has not been disrupted during lamp replacement 10 Plug UV lamp adapter in a socket and verify that the new UV lamp is functioning properly This will be confirmed by continuous green LED light on the adapter This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 7 SANITIZATION OF REVERSE OSMOSIS FILTER Sanitization of the reverse osmosis filter is recommended after it has been in use for an extended period 6 months and when the filter is not going to be used for 3 or more weeks at a time It is also desirable to sanitize the system when replacing cartridges
22. ibited 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 20 4 STEPS FOR INSTALLING REVERSE OSMOSIS SYSTEM Before installing a domestic reverse osmosis filter please carefully read this instruction 4 1 VERIFY YOUR SETUP 1 Check that all parts are in the package Do not open the plastic bags with filter parts before you make sure everything is in place to be able to return faulty incomplete package 2 Check conformity of your local variables to requirements specifications Main pressure Tank pressure Supply water temperature Check water pressure at mains Check pressure in the tank bladder Check temperature of supply water before installing the product Com Compare to the requirements Compare to the requirements in pare to the requirements in paragraph 2 2 paragraph 2 2 in paragraph 2 2 Refer to paragraph 2 2 for recommended measures in case any of the above variables does not meet the requirements verify that your product is as specified in paragraph 2 2 verify that your supply water quality meets the requirements in paragraph 2 3 f supply water quality does not meet the requirements it is necessary to consult with a water treatment specialist 3 Before installing the system make sure there is enough space for both the filter rack and the pres sure tank under the sink In case there is not enough available space pressure tank can be placed in a separate location provide
23. ifications and experience The product should only be used with cold water supply This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 2 SPECIFICATIONS AND COMPONENTS 2 2 SPECIFICATIONS AND REQUIREMENTS Parameter Value 1 Main pressure no booster pump barg 3 6 2 Main pressure booster pump installed barg 2 4 5 3 Tank bladder pressure barg 0 4 0 6 4 Feed water temperature C 4 30 5 Weight of the system base model kg 6 6 Ambient temperature C 5 40 7 Water supply connection 4 thread 8 Filter dimensions HxWxD basic assembly mm 350x450x150 9 Tank dimensions HxWxD mm 350x260x260 fsupply water pressure is below required value purchase pumped model or fit your existing filter with booster pump If the pressure in the water system is above the limit it is necessary to install a pressure regulator on the main pipe f pressure in tank bladder is outside this range it is necessary to pump up or release the pressure until it conforms to the requirement f supply water temperature is up in the range of 20 30 C rejection of impurities will be decreased and system capac ity increased bringing about an increase in TDS Using the product with supply water temperature in excess of 30 C is not recommended 2 3 SUPPLY WATER
24. k filled with chlorine solution for 1 2 hours 11 Open tank valve 6 and drain all water from the tank to the sink Disconnect it from the third pre filter and restore the original tubing of the system 12 Put cartridges in sumps and install the sumps on their heads Then open tank valve 6 and feed valve 6 13 Drain the tank and re fill for at least three times until chlorine odor cannot be smelt This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 8 TROUBLESHOOTING PROBLEM CAUSE SOLUTION Fitting leak Tube is not joined tightly Remove and rejoin the tube Drain saddle leak Drain saddle is not installed properly Reinstall drain saddle as described in paragraph 4 2 in this manual Pre filter sump leak O ring seal is lacking or misaligned Check that the O ring seal is properly aligned in the groove inside sump Sump is not joined tightly Tighten the sump till snug Water runs too slowly from the faucet or slows down sub stantially a few seconds after the faucet is opened Water supply pressure too low This RO system requires at least 3 bar to function properly If necessary install a pressure booster pump or consult a plumber Pre filter cartridges are clogged Replace pre filter cartridges Membrane is clogged Measure permeate flowrate by closing
25. lter cartridges are worn out and should be urgently replaced Delay in the replacement of cartridges can lead to deterioration or destruction of the membrane To aviod such critical situations it is strongly recommended that you change pre filter cartridges at least once every 3 months If the rate of filtration drops significantly and is not helped by replacing pre filters you need to replace reverse osmosis membrane To enjoy purified water of consistent quality it is recommended to replace the membrane at least once in 1 1 5 years In case of prolonged downtime 2 weeks or more it is necessary to sanitize the system as described in paragraph 7 If you plan on leaving for an extended while it is recommended to shut off the water supply This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 25 6 1 PARTS OF THE FILTER AND THEIR RECOMMENDED CHANGE OUT RATES Stage of filtration Name of cartridge Term for replacement first Pre filter cartridges for reverse osmosis feed water pre treatment Life of cartridges depends on quality second of supply water and daily consumption of purified water third Once a year fourth Reverse osmosis membrane fifth Carbon post filter sixth Mineralizing post filter UV lamp 6 2 THE PROCEDURE FOR REPLACING PRE FILTER CARTRIDGES 1 Shut off feed valve 5 and tank
26. olet lamp 17 3 8A Connection diagram for unit with booster pump ultraviolet lamp and mineralizing post filter 18 with single lever faucet 3 85 Connection diagram for unit with booster pump ultraviolet lamp and mineralizing post filter 19 with double lever faucet 4 Steps for installing reverse osmosis system 20 4 1 Verify your setup 20 4 2 Installation procedure 20 5 Steps after installation 24 6 Usage 24 6 1 Parts of the filter and their recommended change out rates 25 6 2 The procedure for replacing pre filter cartridges 25 6 3 The procedure for replacing membrane 27 6 4 The procedure for replacing carbon post filter and or mineralizing post filter 28 6 5 The procedure for replacing UV lamp 28 7 Sanitization of reverse osmosis filter 30 7 1 Sanitization of pressure tank 32 8 Troubleshooting 34 9 Service record 37 10 Environmental and health safety 39 11 Purchasing 39 12 Transportation and storage 39 13 Warranty 39 This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 1 PURPOSE OF THE PRODUCT Reverse osmosis is by far the most advanced technology of water purification in use today Special semipermeable membrane structure similar in its properties to the membrane of a living cell is capable of purifying drinking water from virtually all harmful im
27. operties of the product This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 16 3 CONNECTION DIAGRAMS 3 6B CONNECTION DIAGRAM FOR UNIT WITH ULTRAVIOLET LAMP AND MINERALIZING POST FILTER WITH DOUBLE LEVER FAUCET 2 tube _ 8 5 NN lc ur 7 HH HAH H LL RO 7 36MUV IEEE NER RO 7 50MUV SI LA RO 7 75MUV RO 7 100MUV The manufacturer reserves the right to modify product design or specific components if such modification does not entail deterioration of consumer properties of the product This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 17 3 CONNECTION DIAGRAMS 3 7 CONNECTION DIAGRAM FOR UNIT WITH BOOSTER PUMP AND ULTRAVIOLET LAMP Blue tube 220 220V H l l 2 l l c Models RO 6 36UVP RO 6 50UVP x D RO 6 75UVP UE lt gt 6 100UVP The manufacturer reserves the right to modify product design or specific components if such modification does not entail deterioration of consumer properties of the product This manual is the intellectual property of Eco
28. purities including nitrates and viruses see Figure 1 The membrane can be conceived of as having tiny pores 200 times smaller than viruses and 4000 times smaller than bacteria Domestic water filters with reverse os mosis membranes harness the principle of body s metabolism on a cellular level Only molecules of certain size can penetrate cellular membrane Reverse osmosis system is a five stage filtration unit functioning as follows see section 2 4 for reference numbers Filter rack is connected to cold water supply with feed water adapter 4 and feed valve 5 Red tube carries water from feed valve to the rightmost bulb filter rack Incoming water then passes through pre filter cartridges 9 Pre filter cartridges are designed to remove sol ids such as rust sand silt etc residual chlorine and organochlorines from water After undergo ing pre treatment steps in the pre filters water enters into the fourth and the most important stage reverse osmosis membrane 11 contained in a special housing Inlet of membrane housing is connected with the third leftmost bulb filter rack through the feed side of auto shut off valve four way valve fastened to the top of filter rack One of the two outlets supplies purified wa ter permeate and the other carries away water with rejected impurities concentrate The membrane purifies water at the molecular level by passing through its pores only the water molecules and the molecules of dissolved ox
29. r cartridges are clogged Replace pre filter cartridges Membrane is clogged Measure flow of product water by closing the tank valve and opening the faucet Measured flow rate should correspond to nominal membrane flow rate Missing or misplaced flow restrictor Failure of auto shut off valve Flow restrictor must be installed in the tube running from membrane housing to drain Flow restrictor must face membrane housing If it faces drain saddle fitting clean it and swap ends of the tube so that it is placed at the outlet of membrane housing If flow restrictor was not installed install one The RO system operating ceaselessly while the tank is full may be due to automatic shutoff valve failure Contact the store where you bought this product if no other possible cause can be established Failure of check valve in the transi tion fitting installed at membrane housing permeate outlet Pressure in the empty tank should be 0 4 0 6 bar 6 9 psi Charge the tank to the above pressure if necessary Pressure tank is deflated Open drinking water faucet and let some water out It is normal for the system to stand idle when the pressure tank is full of water water runs to sink drain The system will not turn on no Pressure tank is full Open drinking water faucet and let some water out It is normal for the system to stand idle when the pressure tank is full of water Flow restrictor is clogged
30. reprinting is prohibited 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 2 SPECIFICATIONS AND COMPONENTS 2 4 REVERSE OSMOSIS SYSTEM COMPONENTS 2 Pressure tank 3 Drinking water faucet 4 Feed water adapter 5 Feed valve 4 7 Set of colored tubes 4 pieces S gt 9 1 11 Reverse osmosis 12 Flow restrictor membrane inserted in black tube 13 Locking clip accessory securing push fit connections from inadvertent disconnection in easily accessible locations Presence of the clip has no effect on tightness of the connection Quantity of clips in your reverse osmosis filter may vary depending on design of the product and has no bearing on its performance This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 10 3 CONNECTION DIAGRAMS 3 1 CONNECTION DIAGRAM FOR BASE MODEL eqni Models RO 5 36 RO 5 50 RO 5 75 RO 5 100 Red tube The manufacturer reserves the right to modify product design or specific components if such modification does not entail deterioration of consumer properties of the product This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 3 CONNECTION
31. s stopped The value obtained is dependent on the supply water pressure pressure in water mains 2 Measure recovery proportion of supply water that becomes purified You will need 1 L measuring cup and a stopwatch Shut off tank valve 6 open faucet 3 and measure time that the unit takes to produce 1 L of permeate purified water then close faucet 3 Write down the result tPermeate in the equation below Disconnect the black tube connected to sink drain from drain saddle Open faucet 3 and measure time that the unit takes to produce 1 L of concentrate waste water then close faucet 3 and open tank valve 6 Write down the result tconcentrate in the equation below Calculate recovery using formula t R Concentrate x100 t t Where t is the number of seconds to obtain 1 L of water R is recovery Permeate Concentrate 3 Measure TDS of supply water and TDS of purified water using a calibrated TDS meter 4 Check if the auto shut off valve functions properly Close tank valve 6 and faucet 3 The unit must stop operating water should stop being discharged to drain within 10 minutes 5 Check the unit for leaks 6 Advise unit owner on filter maintenance and encourage to read this manual 7 Make record of commissioning in the maintenance log in paragraph 9 of this book Domestic reverse osmosis system is designed for purification of cold water only If the filling time of the tank increased this means that the pre fi
32. soft Copying and reprinting is prohibited 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 3 CONNECTION DIAGRAMS 3 8A CONNECTION DIAGRAM FOR UNIT WITH BOOSTER PUMP ULTRAVIOLET LAMP AND MINERALIZING POST FILTER WITH SINGLE LEVER FAUCET 220V H Black tube Models RO 7 36MUVP RO 7 50MUVP RO 7 75MUVP E Red tube RO 7 100MUVP MOJA js 220V The manufacturer reserves the right to modify product design or specific components if such modification does not entail deterioration of consumer properties of the product This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 18 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 19 3 CONNECTION DIAGRAMS 3 8B CONNECTION DIAGRAM FOR UNIT WITH BOOSTER PUMP ULTRAVIOLET LAMP AND MINERALIZING POST FILTER WITH DOUBLE LEVER FAUCET To Um Fm 8 B i 3 ay E el 220B 220B Black tube fal m a eqni Qi EL Models RO 7 36MUVP RO 7 50MUVP E RO 7 75MUVP San 2 2 RO 7 100MUVP The manufacturer reserves the right to modify product design or specific components if such modification does not entail deterioration of consumer properties of the product This manual is the intellectual property of Ecosoft Copying and reprinting is proh
33. sticinssrt S 1 4 ferrule LS 1 4 compression nut blue tube 8 Select spot where you are going to install the filter and make two holes The distance between the holes in the wall must precisely correspond to that between the holes in the bracket Allow for at least 100 mm gap between the bottom of the filter and floor Install screw anchors if necessary and screw in two screws not included The distance between the holes is 272 mm 9 Insert cartridges into the first and the second housings in the direction of water flow leftwards 10 Tighten all the three sumps by hand 11 Unplug the tube that connects the third housing in the direction of water flow with the auto shut off valve from the valve This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 22 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 23 4 STEPS FOR INSTALLING REVERSE OSMOSIS SYSTEM 12 Open the water tap 5 and let through the first two pre filters with cartridges 5 7 liters of water to wash off the coal dust that may appear in cartridges during shipping CAUTION This water will pour through the tube disconnected from auto shut off valve prepare a vessel to collect it 13 Insert the cartridge into the third sump along water flow direction and attach the sump back again Let through at least 4 liters of water to wash off the coal dust Close the feed valve 5 and connect the free end of th
34. tank valve 6 and opening faucet 3 Use a measuring cup to check if the time it takes to produce 1 L drinking water is as follows 8 minutes with 50 god membrane 5 6 minutes with 75 gpd membrane 4 minutes with 100 gpd membrane If it took twice as long or more to produce 1 liter of water the membrane may need to be replaced refer to the store where you bought this product A tube is kinked Straighten the tube Pressure tank is deflated Pressure in the empty tank should be 0 4 0 6 bar 6 9 psi Charge the tank to the above pressure High noise Air in the auto shut off valve The air will go away by itself with continued Operation of the system Water supply pressure too high Check your water supply pressure If necessary install a pressure regulator or refer to a plumber This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited 2014 34 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 8 TROUBLESHOOTING 35 Auto shut off valve knocks Pressure surges in water mains Install a check valve on the main pipe in your kitch en or at the point of entry of your home s water supply Refer to a plumber The system is always on water is drained continuously Water supply pressure too low This RO system requires at least 3 bar to function properly If necessary install a pressure booster pump or consult a plumber Pre filte
35. the purified water faucet so that the tank starts to re fill Depending on the pressure in your water mains filling may take 1 5 to 3 hours After the second tank re fill you can safely use the purified water 6 5 THE PROCEDURE FOR REPLACING UV LAMP UV lamp replacement should be performed by a qualified specialist Recommended life of the UV lamp is 9000 hours approximately 1 year of continuous operation CAUTION Using UV lamp beyond the recommended service life is disapproved since the intensity of UV radiation and its germicidal efficiency will be reduced It is strongly forbidden to turn on the UV lamp power when the lamp is not in metal housing and to look at a glowing lamp This can lead to eye damage and result in deterioration or loss of vision When replacing the UV lamp it is advisable to clean the quartz sleeve Do not use abrasive mate rials to clean the sleeve as this may decrease transparency of the sleeve to UV radiation thereby reducing the efficiency of disinfection Be careful when removing the quartz sleeve from the housing to avoid damaging or scratching the sleeve This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 28 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 29 Use care when removing sealing rings from the ends of the sleeve The rings serve to protect the lamp and electrical connections from water leaks UV lamps should be handled wit
36. valve 6 2 Wash your hands with antibacterial soap 3 Unscrew with the sump wrench 10 first and second sumps in water flow direction right to left Be careful as the sumps are filled with water 4 Remove the used filter cartridges 5 Wash sumps with unflavored soap and a clean sponge then rinse thoroughly with water 6 Insert the new cartridges in the first and second sumps by water flow direction 7 Disconnect the tube stemming from the third sump from the auto shut off valve 8 Open the feed valve 5 and let through the first two installed cartridges 5 7 liters of water to rinse the coal dust that may be produced in cartridges during shipping CAUTION This water will pour through the tube disconnected from auto shut off valve prepare a vessel to collect it This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 9 Remove the third pre filter s sump from filter head Be careful as it is filled with water 10 Remove the used filter cartridge and wash the sump with unflavored soap and a clean sponge then rinse thoroughly with water 11 Insert new cartridge into the third sump Screw the sump back on and let through at least 4 more liters of water to flush the coal dust Close the feed valve 5 and connect the previously separated tube with the auto shut off valve 13 Openthe tank valve
37. ygen Concentrate TER o o0 o x for disposal gt 2 06 odd p RO rate P90 y 0950 cu oe 009 06 P o Go SG wA Tap water under Membrane pressure c Water o Molecules of smaller Larger molecules molecules size pure water Figure 1 This manual is the intellectual property of Ecosoft Copying and reprinting is prohibited O 2014 REVERSE OSMOSIS SYSTEM INSTALLER AND USER GUIDE 1 PURPOSE OF THE PRODUCT Inside the membrane water is separated into two streams concentrate which is discharged into drain and permeate which enters pressure tank 2 for storage The tank is connected to the output through the membrane auto shut off valve and check valve built into the transition fitting that is installed in permeate outlet of membrane housing After the auto shut off valve is installed the union tee through which the tank is connected to the filter rack with yellow tube On the top of the tank tank valve 6 is installed Pressure tank of the system accumulates purified water Without it reverse osmosis membrane wouldn t be able to produce sufficient flow for direct water consumption For example if the filter had an installed membrane with a performance of 50 GPD 7 9 h a glass of 200 ml would take over 1 5 min to fill Thus the system stores purified water in the tank and delivers it to the user as needed and then generates a supply of water Time required to fill empty tank can range from 1
Download Pdf Manuals
Related Search