ICM-ETHi/User Guide
Contents
1. ICM ETHI RAPFEILT el 1 Introduction The ICM ETHi provides a convenient solution for connecting the ICM to an eth ernet network It plugs in directly to the ICM using a pre wired connector It can be used with Lantronix software for network configuration The following functions are provided Ethernet to RS485 adaptor using Lantronix drivers DC input socket for ICM power Pre wired ICM connector on 3m flying lead ICM signals brought out to user accessible terminal block This allows external alarms PLCs or a start button to be easily connected LED Indicators indicating Transmit Tx and Receive Rx data RR ICM ET HI Figure 1 Introduction 2 Installation An overview is given here for when the customer will be using our LPA View soft ware This involves the following steps 1 Connection e Connect ICM ETHi to the ICM e Plug the ICM ETHi cable into the ICM e Connect DC power supply either using the DC connector provided or via the internal terminal block e Connect network cable between ICM ETHi and customer network switch e Install the Device Installer software from the Software CD or from the following web address http Itxfaq custhelp com app answers detail a id 644 e Navigate to the Device Installer via Program menu Follow menu instructions e Identify and record the LAN address used by the device e g 81 187 19 55 e Access the Internet explorer enter the LAN address in t2. Click on the desired Com port number any can be used that do not conflict with existing allocations Press OK to close the dialogue The new Com port will be shown in the left hand pane with the settings in red in the right hand pane As a shortcut the settings can be filled in automatically Click on the New Com port shown on the left hand pane in Figure 3 Then double click the found device shown in the Device List at the bottom of the dialogue Press the Save button to save the configuration Configuration Test Network communications can be tested using the Tests tab as in Figure 4 Press the Open button If successful the dialogue will show Com Status Open Press Close afterwards otherwise the Com port will not be available to LPA View After this configuration the new COM port will be available to the LPA View Test Analysis Software Proceed to connect to the ICM as detailed in the main ICM manual 8 Configuration File ComPort Device Tools Help Xy Add Remove Save B Refresh J Search For Devices Exclude Settings Com 1 New Window s Port Name Window s Device Name Window s Service Name Listen Mode Normal port closed after disconnect TCP KeepAlive 7200000 KeepAlive Time msec RFC 2217 DTR In Tie DTRto DCD DSR always active TruPort WARNING the Host is on t 217 169 15 184 10001 4 NRI C a File ComPort Devic
3. 100m x BLUE BLUE krass MELLOW Era YELLOW YELLOW DATA o GREEN X X L BKG xX X GREEN GREEN I n START fo Vit ne COMMON o i op 1 i op2 o i pc of USER WIRING avll OPTIONAL DATA e i I o i j i Figure 5 Control Cable Extension The standard cable is 3m in length Wiring over longer distances should be done using twisted pair cabling assuming the serial communications signals are being used Figure 5 shows an example 12 Wiring Options Produced by MP Filtri UK Revision 0 4 As a policy of continual improvement MP Filtri UK reserve the right to alter specifications without prior notice Except as permitted by such licence no part of this publication may be reproduced stored in retrieval system or transmitted in any form or any means electronic mechanical recording or otherwise without prior written permission of MP Filtri UK MP FILTRI UK Limited Bourton Industrial Park Bourton on the Water GL54 2HQ UK Tel 44 1451 822522 Fax 44 1451 822282 Email sales mpfiltri co uk Website www mpfiltri co uk ITALY HEADQUARTERS MP FILTRI S p A Tel 39 02 95703 1 Fax 39 02 95741497 95740188 Email sales mpfiltri com Website www mpfiltri com CANADA MP FILTRI CANADA INC Tel 1 905 303 1369 Fax 1 905 303 7256 Email mail mpfiltricanada com Website www mpfiltricanada com CHINA MP FILTRI Shanghai Co Ltd Tel 86 21 58919916 Fax 86 21 58919
4. 667 Email sales mpfiltrishanghai com Website www mpfiltrichina com GERMANY MP FILTRI D GmbH Tel 49 6894 95652 0 Fax 49 6894 95652 20 Email service mpfiltri de Website www mpfiltri de FRANCE MP FILTRI FRANCE Tel 33 1 40 86 47 00 Fax 33 1 40 86 47 09 Email contact mpfiltrifrance com Website www mpfiltri com INDIA MP FILTRI INDIA Tel 91 9945599899 Email s mishra mpfiltri com Website www mpfiltri com RUSSIAN FEDERATION MP FILTRI RUSSIA INC Phone mobile 7 095 502 5411 Fax 7 095 205 9410 Email mpfiltrirussiag yahoo com Website www mpfiltri ru USA MP FILTRI USA Inc Tel 1 215 529 1300 Fax 1 215 529 1902 Email sales mpfiltriusa com Website www mpfiltriusa com UAE MP FILTRI UEA Tel 4 91 9945599899 Email s mishra mpfiltri com Website www mpfiltri com
5. USER WIRING 0P OPTIONAL DC av DATA DATA 9 9 9 9 9 9 P 9 o o 0 0 0 O O o Figure 1 Pre wired ICM Cable Figure 1 shows the standard cable wiring This is how the standard ICM ETHi unit is delivered 10 Wiring Options START c COMMON Je OP 1o OP2 o DC je Qv e DATA o DATA o Figure 2 External Start Figure 2 shows how to connect an external start button or PLC output relay START COMMON OP1 OP2 DC QV DATA4 lo FAIL PASS DATA LAMPS Figure 3 External Indicators Figure 3 shows how to connect external indicator lamps in case the built in LED is not sufficient These could also be PLC inputs START o COMMON o OP 1 o OP2 o DC Je i AC av le AC SUPPLY DATA o ES DATA o Figure 4 External Power Supply Wiring Options 11 Figure 4 shows how to connect an external power supply This arrangement may be preferred for permanent installations over the removable plug top power supply that comes with the unit CONTAMINATION MONITOR ETHi Dr Re PA NET UNE DO ON re COS Om 1 OE EURO MIU De ua b uL FUE ONES t Lu i JUNCTION BOX 2 I 1 I lt PINK i PINK pj PINK gt START i GREY x i GREY GREY COMMON e i e op e HITE WHITE WHITE I ji OP2 e _ XX BR i BRUN 3m DC e i e gy o BLUE xX X
6. ation 4 Configuration IP Address In order to communicate on the network the ICM ETHi requires an IP address If you have a DHCP server on the network this will happen automatically Otherwise it is possible to assign one manually using the Lantronix Device Installer program a separate free program available from the Lantronix web site Creating the Virtual Com Port Connect up the ICM ETHi as described above and apply power When the unit is connected correctly you should see a continuous green LED to the left of the RJ45 socket after it has obtained an IP address Run the CPR program Once started press the Search button to search the network for ICM ETHi devices Any such are displayed on the bottom line as in the example below with an appropriate IP address for your network v CPR Manager 4 3 0 0 Co S RE File ComPort Device Tools Help W Add Remove Save Refresh J Search For Devices Exclude Com Ports Hide Com Port List General Tests gt All Com Ports Com Port IP Address TCP Pot Com Status Network Status r 4 G Device List Collapse 9 IP Address Ports TCP Pot Product ID HW Address Network Interface 810 022 1 10001 XPort 03 04 X5 00204A BF 38 88 10 02 15 4 TT r Figure 1 Searching the Network Once the device is found a COM port can be created to enable it to be accessed from LPA View Click the Add Remove button to display the Com Ports dialogue Figure 2 Configurat
7. e Tools Help W Add Remove el Save B Refresh J Search For Devices Exclude Com Ports Hide e Com Sas Ope Network Status Connected to 217 169 15 184 10001 RS232 OUT gt RTS DTR Ports TCP Por Product Status of Com Port 1 is Open and Connected to 217 169 15 184 10001 Open Close Testis Running mm Figure 4 Testing Configuration 5 Wiring Options The unit can be used as is for simple PC control of an ICM However all the ICM signals are made available at a terminal strip within the in terface so that these can be connected to a customers equipment These include a start signal and the two alarm outputs Also included are the DC power input customers may prefer to permanently connect an existing supply here rather than plugging in the provided DC adaptor The RS485 signals Data Data are also present these may be connected to an existing Modbus network To access the terminal strip remove the four screws holding on the right hand end plate the one with the ICM cable The end plate can then be detached and the top plate slid off An additional cable gland supplied can be fitted in the spare po sition on the end plate and used for customer wires Some example arrangements are shown here there is more information in the main ICM manual START DC INPUT COMMON O0P1 OP2 DC AV ETHERNET DATA DATA START COMMON opt
8. he navigation bar Press enter e Access the Serial Settings tab and configure with the following changes from the default can reset to default settings first Protocol RS485 2wire Flow Control None Baud Rate 115200 Installation 3 Data Bits Parity Even Stop Bits 1 Scroll Down to the bottom of the window and click Ok From the left hand options click Apply Settings Install the Com Port redirector software from the Software CD or from the following web address http Itxfaq custhelp com app answers detail a id 928 Navigate to the CPR Manager via Program menu and Open Add a new Com Port Add and Remove Select tick an unused Com Port e g Com 3 and click Ok Configure the Com Port being used double click on COM port Host use value recorded earlier e g 81 187 19 55 TCP Port 10001 Press the Save button menu bar save settings Please Note the following message may appear Hardware Installation A A The software you are installing for this hardware Lantronix CPR Port has not passed Windows Logo testing to verify its compatibility with Windows XP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo
9. ion 7 Com Ports W Comt F Com21 Com41 F Com61 Com81 F Com10 F Com121 E Com F Com22 Com42 F Com62 Com82 Comi02 F Com122 E Com3 Com23 Com43 F Com63 Com83 F Com103 F Com123 7 Com4 7 Com24 F Com44 F Com64 7 Com84 Comi04 F Com124 7 Com5 7 Com25 Com45 Com65 Com85 Com105 F Com125 7 Com6 7 Com26 Com46 Com66 Com86 Comi06 F Com126 7 Com7 7 Com27 Com47 Com67 Com87 Comi07 F Com127 7 Com8 Com28 Com48 F Com68 Com88 Com108 T Com128 E Com F Com29 F Com49 Com69 Com89 F Com109 F Com129 7 Com10 Com30 F Com50 Com70 Com90 Com110 F Com130 7 Comit Com31 F Com51 Com71 F Com91 F Com111 F Com131 7 Com12 F Com32 Com52 F Com72 Com92 Com112 Com132 7 Com13 F Com33 Com53 Com73 Com93 Com113 Com133 7 Comi4 F Com34 Com54 Com74 Com94 Comii4 F Com134 Comi5 Com35 Com55 Com75 Com95 F Com115 F Com135 7 Comi6 7 Com36 F Com56 Com76 Com96 Com116 Com136 7 Comi7 7 Com37 7 Com57 7 Com77 F Com97 7 Comi17 E Com137 7 Com18 F Com38 Com58 F Com78 Com98 F Com118 F Com138 7 Com19 F Com39 Com59 F Com79 Com99 Com119 F Com139 E Com20 Com40 Com60 Com80 Comi00 F Com120 F Com140 4 m r 0K Cancel Check Range to 256 j Select All SelectNone Uncheck Range 1 t to 256 Figure 2 Com Ports dialogue
10. testing Continue Anyway STOP Installation Figure 1 Installation e Click Continue Anyway on all warnings e Access e g Com 3 test tab click Open to prove connection to the Ethernet adapter e Click Close and shut down CPR manager and Device installer e The new COM port e g COM 3 will now be available in LPA View e Install LPA View as per the user guide e Open LPA View open remote control 7th button from left on toolbar e Choose relevant Com port and click Ok Installation 5 3 Lantronix Software Installation We supply a version of the software on CD or the latest version from the Lantronix web site can be used Run the CPR installer This is a file with a name like setup_cpr_x86x64cd_4 3 0 0 Accept the security warning and license I CPR Installer os s In order to install CPR you must first install these components M Microsoft NET Framework 4 0 x86 x64 CPR 4 3 0 0 x86 Install Close Windows 7 x86 Figure 1 The CPR Installer The software requires the Microsoft NET Framework If you do not have this already the installer will first install it for you You will then need to restart the computer and run the installer again to install the actual CPR program Follow the installation wizard accepting the defaults You will need to accept another security warning in order to install the Com Port driver software 6 Lantronix Software Install
Download Pdf Manuals
Related Search