Aquamaster User Guide Cover
Contents
1. Fig 10 Fig 11 Pin should sit on top of the moulding 12 Adjusting the height of the gantry Position the gantry in its required location prior to adjusting the height and checking level Take care when moving the gantry to the desired location Move one leg at a time in small increments The gantry should be level in all directions Check this using the spirit levels on the feet and end beams Centre the bubble in the spirit level window as Fig 12 Use the large handwheels on the feet to adjust level as required as Fig 12 13 If the height of the gantry needs to be raised release the middle handwheel Hold onto the top handwheel with one hand pressing the release levers in on the leg with the other hand and push the leg up to the required height one hole at a time raising one leg and then repeating by the same increment on the other side Ensure it clicks into position and the pin is flush with the block as Fig B Secure with the middle handwheel and check for level using the spirit levels on the end beam Repeat for other side If the leg height is raised always ensure adequate clearance overhead User Guide Fig 12 i Lever NOT correctly engaged Lever correctly engaged Y Chiltern Invadex LiteTrack Portable Gantry Final positioning 14 Attaching the2. Keep this user guide readily available for other users Always ensure there is sufficient clearance width and height to erect dismantle the gantry If the gantry is to be dismantled always remove the Wispa Lite portable hoist from the gantry before attempting to dismantle the gantry The hoist should be lowered onto a bed chair or a Chiltern Invadex transportation trolley before it is disconnected from the gantry track Always follow the assembly dissassembly instructions contained in this guide Chiltern Invadex Lite Track Portable Gantry LiteTrack Gantry Assembly Instructions Check all components are available prior to assembly Notes If the gantry is to be assembled over a bed The gantry can be assembled over a bed unless it is occupied If the bed is occupied assemble the gantry away from the bed and then position afterwards as a guide this would be approximately 900mm from the head board but always ensure the gantry track is directly above the clients centre of gravity 1 Preparation 1 Unpack all components and lay on the floor ready for assembly 2 Check all parts are available see Fig 1 and for damaged components 3 Safety note The corner quadrant located on the end beam see Fig 1 should always have tension Check to ensure it does not swing freely and there is tension Corner Leg section x 2 Foot section x 2 quadrant x 2 O W pS End beam x 2 pa Cassette x 1 Gas strut x 2 2 Le
3. 7 B 8 General safety note When placing the top beam on the legs always position hand behind the corner quadrant as Fig 8 1 Do not lift the whole cassette section With one end of the cassette resting on the floor hold the assembled leg with one hand raise the beam section and place on top of the leg as Fig 8 2 A User Guide Fig 8 1 ES Corner quadrant Note hand grasp point for safety when assembling beam Fig 8 2 Chiltern Invadex Lite Track Portable Gantry 9 Securing the cross beam to the cassette Adjust the position of the leg as Fig 8 2 B to allow the corner quadrant to be connected this should be at 90 degrees to the leg and cross beam Pull the corner quadrant back against the leg and hold with one hand against the leg as Fig 9 A Check the cross beam has been locked in position on the legs Be aware of finger trapping hazard when pulling corner quadrant back against the leg Secure in position using the handwheel as Fig 9 B 10 Place the second leg within easy reach and raise the end of the beam Place on top of the second leg as Fig 10 Note Check the pin on the cross beam sits on top of the moulding on the legs as Fig 10 Pull the corner quadrant back against the leg at 90 degrees to the leg and cross beam and hold with one hand against the leg as Fig 11 A Secure in position using the handwheel as Fig 9 B Fig 9
4. C Repeat for other side 20 Leg disassembly Where there is limited head room it is recommended that the leg section is laid on its side for disassembly as Fig 20 Loosen the lower black handwheel as Fig 20 A The gas strut and leg section will then slide apart Safety note The gas strut is compressed and will spring out Pull the leg section apart from the gas strut as Fig 20 B and remove the gas strut from the foot section C Repeat for other side 21 Ensure top handwheel is loose and depress the release levers as Fig 21 A and push the leg section down to the lowest position as Fig 21 B Fasten both handwheels C for safe transportation Repeat for other side User Guide Fig 20 Fig 21 Chiltern Invadex Lite Track Portable Gantry Width calculation guide The table below can be used as a quick reference guide to help determine the internal width of the gantry depending on the hole position which has been selected For example when the first hole position is selected on the end beam and the same on the right end beam the internal width is 1890mm which will typically allow the transfer of a client from a single bed to a shower chair LEFT Hole position 1 1890 Typical single bed to shower chair 2020 Typical single bed to riser recliner chair 2150 Typical domestic double bed to shower chair RIGHT 2020 T
5. Wispa Lite Portable hoist Rest the Portable hoist on the bed or trolley ready for attaching to the eye on the gantry Release sufficient tape to connect the carabena on the hoist to the eye on the gantry as Fig 14 Do not lift the hoist to attach it to the gantry 15 Final safety check Fig 14 Prior to hoisting a client check All handwheels are in place 3 per upright and they have been securely tightened The gantry is level in all directions The height and width of the gantry are appropriate for the dy F task eg there is sufficient space to position a wheelchair or shower chair at the side of the bed for transfer The gantry is now ready for use The weight of the hoist will release the cassette and allow it to travel freely along the beam as Fig 15 Slide the hoist across the gantry to the desired position ready to lift transfer the client Take care when moving around the gantry to avoid trip hazards such as the legs handwheels and potential injury from the corner quadrant or cassette 10 User Guide 16 Disassembly of the gantry if Do not lift the hoist Lower the hoist by releasing sufficient tape to disconnect the carabena on the hoist from the eye on the gantry as Fig 16 B Remove the hoist from the gantry Always ensure the cassette is locked in the central position before disassembling the gantry To achie
6. COMME cee isos Telephone NO oa Engineers training cert no Signature Date aaa Ioe Tesla Kgs A MO noone secre cepe sree tree arene A Ne soe Serviced By Company oia Telephone Noore a A E E IES Engineers training cert no Signature Dates Loadimested TOn mne Kgs Comment onne e ea e E E A R ONS Chiltern Invadex Lite Track Portable Gantry Gantry Service Record Serviced By esiis T E ereccrerrerd rerca tereerpereeeer ree spr eerreee Telephone NO oras Engineers training cert no Signature Dates conoscan Loadmestod o Kgs Comments a e E Serviced By COMM aa Telephone NO er isinai iaa Engineers training cert no Signature Dates Load Testedi To me Kgs ETT E E R Serviced By company m Ono Sey eer creer Telephone No sico rd Engineers training cert no Signature Data erna ane Loadosted Mo a Kgs Comments o e e a a E RREA 20 Models covered Please fill in the information below for future reference OHWLTRK 1 OHWLTRK 2 Dealers Name Telephone Your Serial Number is Gantry System 23 Chiltern Invadex Solutions for Living Chiltern Invadex Ltd 6 Wedgwood Road Bicester Oxfordshire OX26 4UL Tel 01869 246470 Fax 01869 247214 Overseas Enquiries Tel 44 0 1869 365545 Fax 44 0 1869 365567 Web www chilterninvadex co uk E mail sales chilterninvadex co uk Chiltern Invadex NI Ltd 5 Balloo Way Balloo Industrial Estate Ban
7. Portable Gantry user guide Wispa Lite Track Chiltern Invadex utions for Living Portable Gantry System Chittern Invadex Solutions for Living User Guide Contents Intended use of the Product sese 2 Things to consider before using the GAMNUIY caca ripio 2 Assembly Guide sees eee eee eee eee eee 4 Disassembly guide sss esse 11 Servicing amp maintenance see eee eee eee 15 A AO 15 Troubleshooting ooconoconocanocanicnnanananccinacanacnnno 16 Gantry Specification neeesser eee eee neee eee 17 WY Ty sz 11T 18 Gantry Service Record sees ee eee 19 This product has been designed to the highest standards with safety strength and quality in mind Follow the recommendations in this guide to ensure maximum benefit from your Wispa LiteTrack Gantry system Should you experience any difficulties please consult the trouble shooting guide prior to contacting your LiteTrack Gantry supplier Read the safety section of this guide prior to use this is contained on page 2 Chiltern Invadex Lite Track Portable Gantry Intended Use of the Product The Wispa LiteTrack gantry sytem has been designed to lift and transfer a less able person with the help of a carer The gantry is portable and can easily be relocated and reassembled wherever required It should be used with the WispaLite Portable Hoist and a Wispa sling or other lifting accessories from the Chiltern Invad
8. aterials within the first 2 year period please contact your point of purchase Repairs made during the warranty period will be carried out free of charge provided the product has been used strictly in accordance with the guidelines set out in this user guide Our warranty does not cover replacements adjustments or repairs which may be required as a result of normal wear and tear wilful or accidental damage misuse neglect or any other cause which is beyond the control of Chiltern Invadex Modifications and repairs made to this product by unauthorised persons will render the warranty void Only parts manufactured or approved by Chiltern Invadex shall be used to repair this product Use of unauthorised parts will invalidate all warranties and remove all liability from Chiltern Invadex for the safety of this product Chiltern Invadex shall in no event be liable for any damages costs or expenses arising from any claim made under this warranty save for any legal liability of Chiltern Invadex for death or personal injury resulting from the company s negligence in respect of its products This warranty does not affect your statutory consumer rights User Guide Gantry Service Record Serviced By COMPANY o cer tooo aria Telephone NO as Engineers training cert no Signature Dap rete ECES COO e a Kgs Comments e m cece se eroce er eerecraceerer er er eee rar bedereer ecrercerorcereere rarer Serviced By
9. chargeable If the maintenance of the equipment is the responsibility of a third party for example the Social Services please contact them in the first instance Gantry Specification 2040 2560 j A S 1 T 4 H RL l Es 1 2165 2465 C 1 50mm intervals Gantry at highest position 1825 e a Gantry at lowest position 1525 gi H 440 1010 1530 H LA at Ca 1 1100 1890 2410 Internal Lifting capacity 210 Kg 33 stone 460 Ib including hoist Construction Legs steel Track Aluminium Cassette Aluminium with ABS cover Lifting Range Approximately 1525mm 1825mm Maximum loading per foot 100kg 16 stones 220Ib provided that the gantry is used in accordance with the instructions in this user guide Assembled component weights Lower Leg section x2 7kg each 15 5Ib Upper Leg section 8kg each 18lb Cassette x1 11kg 241b End section corner quadrant x2 5kg each 111b Gas strut x2 1kg each 2 2lb Total weight of gantry 53kg 116lb CE MARK The Chiltern Invadex Wispa LiteTrack Gantry carries the CE mark and complies with EC Directives Medical Device Directive 93 42 EEC 17 Chiltern Invadex Lite Track Portable Gantry Warranty Your Chiltern Invadex Wispa LiteTrack Gantry carries a 2 year warranty from the date of purchase subject to the following Should you experience any problems with our workmanship or m
10. ere is no tension in the corner quadrant Leg does not raise easily falls under gravity Gas strut will not compress 16 suggested cause Cable tension is incorrect Leg section is incorrectly positioned End beam section is incorrectly positioned Push pin in manually Spring mechanism is damaged Thread on feet is damaged or twisted Spirit levels are damaged or broken Spring mechanism is defective damaged Gantry leg not positioned correctly to accept the corner quadrant Corner quadrant is defective damaged Washers in the corner quadrant are damaged defective Adjust grub screws Gas strut is damaged Gas strut is damaged solution Contact Chiltern Invadex for assistance Adjust leg position Adjust end beam position If problem persists contact Chiltern Invadex for assistance Contact Chiltern Invadex for assistance See replacement parts list in this booklet Contact Chiltern Invadex for parts Contact Chiltern Invadex for replacement parts Contact Chiltern Invadex for assistance Reposition gantry leg at 90 degrees Contact Chiltern Invadex for assistance Contact Chiltern Invadex for assistance Check tension Contact Chiltern Invadex for assistance Contact Chiltern Invadex for assistance User Guide Further assistance Please telephone any Chiltern Invadex Office for further assistance Remember that service calls made after the guarantee period will be
11. ex range as assessed by a trained person Note Not all slings and accessories are compatible with the Wispa Lite hoist If you are unsure please contact your nearest Chiltern Invadex Office The correct and appropriate use of this product will reduce the risks associated with manual patient handling The lifting transferring task should be assessed and planned by a trained person Safety Considerations Safety e Only a single hoist should be attached to the gantry at any one time e Do not operate the WispaLite Portable Hoist and gantry without training in the safe operation of the hoist gantry and slings The gantry should only be assembled by a competent person e Only use slings which have been assessed as suitable by a competent person e Read the Wispa Lite Portable hoist User Guide in conjunction with this guide e Read the relevant Sling User Guide which is provided with each sling It explains in detail how to use slings correctly e Do not use the Gantry if there is any doubt about the integrity of the gantry wear to the hoist carry bar or there is fraying or stitch damage to the lifting tape or slings or if the gantry or hoist itself is damaged in any way e Do not exceed the Maximum load of the gantry or hoist Wispa LiteTrack Gantry 210kgs 33 Stone 460 Ib WispaLite Portable Hoist 200kgs 31 Stone 440 Ib e Ensure when the gantry and hoist are in use that the surrounding area is clear and the person being
12. g assembly Loosen both black handwheels on the leg as Fig 2 C amp D Push both release levers in with one hand as Fig 2 A pull out the inner leg section to the first position as Fig 2 B having let go of the release levers This should then click into place the pin will be flush with the top of the block when in the correct position Secure the leg with the locking knob Fig 2 C Note The height of the unit can be adjusted later when the gantry is fully assembled VEN DE Fig 2 7 3 Locating the leg and foot sections and inserting the gas strut Where there is limited head room it is recommended that the foot section is laid on its side for assembly as Fig 3 Insert the gas strut in the orientation shown in Fig 3 Place the leg section over the gas strut as Fig 3 B Note Orientate the leg to ensure the top catch bracket is pointing towards the floor while raising the leg at the same time taking care not to damage the gas strut compressing the gas strut and pushing down as far as the moulding on the foot section as Fig 3 C Note The bottom handwheel needs to be almost all the way out 4 The top catch bracket should be located on the inside as Fig 4 Tighten the lower handwheel to secure in place Safety note The leg is not yet free standing Do not leave the leg unattended Lay it on the floor against a bed or wall Repeat f
13. gor County Down BT19 7QZ Tel 028 9145 0497 Fax 028 9127 0046 Chiltern Invadex Ltd Unit 16 Evans Business Centre 68 74 Queen Elizabeth Avenue Hillington Industrial Estate Glasgow G52 4NQ Tel 0141 880 9986 Fax 0141 880 9990 Copyright Chiltern Invadex Ltd The design of the product shown in this User Guide is vested in Chiltern Invadex Ltd and should not be copied or reproduced in anyway whatsoever without the express permission in writing of Chiltern Invadex Ltd Published by Chiltern Invadex Ltd 6 Wedgwood Road Bicester Oxon OX26 4UL Registered in England No 1182024 In Ireland Chiltern Invadex NI Ltd 5 Balloo Way Balloo Industrial Estate Bangor County Down BT19 7QZ Registered No 19958 CINV435 01 08 05
14. lifted is clear of all objects e Always ensure the gantry is assembled and adjusted for level using the spirit levels on the end beams e There are only 3 width adjustment holes per end beam The pin must always be located in one of these After use User Guide Always ensure the gantry track is directly above the clients centre of gravity Hoists should only be used to lift vertically Lifting at an angle will wear the lifting tape prematurely and affect the stability of the gantry Always ensure the top beam is horizontal and the leg adjustment pin is located in the same position on each side All fixings should be checked on a regular basis The cassette case and mechanical parts should only be removed by a qualified service engineer trained by Chiltern Invadex Do not touch any of the moving parts in the hoist unit or in the track Call Chiltern Invadex for assistance Always ensure the legs are positioned as shown in Fig 13 of this user guide Take care when moving around the gantry to avoid trip hazards such as the legs handwheels and potential injury from the corner quadrant Take care when attaching or removing a sling as a swinging carry bar or hoist could cause injury For maximum comfort always move the user in one movement and avoid stop starting the hoist Some occupants are reassured if the carer holds them whilst the hoist is traversing across the track Never leave a client unattended on the gantry
15. m cleanliness Wipe with a dry cloth Gantry and hoist For stubborn marks use a damp cloth and a mild cleanser Always read the manufacturers instructions prior to applying the cleanser Avoid using cleaning agents which contain chlorine carbolic acid or other strong chemicals as these may damage the metalwork and plastic components Parts item description aty part no 1 Upright mouldings kit all mouldings for legs 1 360 80001 1 1 1 1 1 Beam mouldings kit all mouldings for horizontal beam 360 80002 Hand Wheel Black COM0081 Levelling Foot Kit 360 80011 Spirit Level spares kit x4 spirit levels 360 80003 Gas strut assembly spares kit x1 360 80004 Gl Gl A N 1 5 2388 S Sn a 2 88 SS m e N Note Replacement parts should only be installed by trained personnel The gantry then needs testing once parts have been replaced il 1 Chiltern Invadex Lite Track Portable Gantry Troubleshooting symptom Cassette travels further in one direction along the beam than the other Pins do not click into position on the leg Pins do not click into position on the end beam cassette Spring mechanism is stuck on the leg end beam section Spring mechanism has failed on the leg end beam section and will not push in manually Height of feet cannot be adjusted Cannot check gantry is level Lifting eye on cassette will not come down Corner quadrant will not fold back against the leg Th
16. or other leg User Guide Fig 3 Fig 4 Top catch bracket on leg section facing inward Chiltern Invadex Lite Track Portable Gantry 5 Assembling the cassette and end beams Notes 1 The end beams which attach to the cassette are identical 2 The cassette can be positioned either way round 3 Assemble the cross beam as close to the legs as possible Rotate the corner quadrant to the position shown in Fig 5 Push the release lever down with one hand as Fig 5 A and slide the end beam into the cassette as Fig 5 B having let go of the release lever as the end beam begins to slide and select the appropriate hole depending on lifting task see p14 for Width calculation guide The end beam will then click into place the pin will be flush with the top of the block when in the correct position Repeat for other side 6 Attaching beam to leg section Please note prior to assembly Top catch bracket on the leg section should be on the inside to accept the beam as Fig 6 Fig 5 Fig 6 m Top catch bracket on leg section facing inward py 7 Fold over the corner quadrant on both end beams in preparation for connecting to the leg as Fig 7 A Ensure the cassette is centralised in the correct position latched To achieve this slide along until it clicks into position in the centre of the rail as Fig
17. ve this slide the cassette along until it clicks into position in the centre of the rail as Fig16 A If the height of the gantry needs to be lowered release the middle handwheel Hold onto the top handwheel with one hand pressing the release levers in on the leg with the other hand and push the leg down to the required height one hole at a time lowering one leg and then repeating by the same increment on the other side If the bed is occupied relocate the gantry to a suitable place ready for disassembly Fig 16 Disassembly of the gantry E Sd Chiltern Invadex LiteTrack Portable Gantry 17 Important safety note 1 Completely remove one leg BEFORE releasing the second leg 2 Ensure there is sufficient space to lower the gantry Remove the upper handwheel which locks the corner quadrant in place as Fig 17 A Fold back the corner quadrant against the cassette as Fig 17 B one leg ata time Push the beam upwards as Fig 17 C Safety note The leg is not free standing Do not leave the leg unattended Lay it on the floor against a bed or wall 18 Lower the beam to the floor as Fig 18 whilst retaining the leg with the other hand Repeat for other side 12 Fig 17 19 Fold back the corner quadrant as Fig 19 A depress the release lever as Fig 19 B and slide out the end beam section as Fig 19
18. ypical single bed to riser recliner chair 2150 Typical domestic double bed to shower chair 2280 Typical nursing double bed to shower chair Dimensions are in mm and for guidance only 14 2150 Typical domestic double bed to shower chair 2280 Typical nursing double bed to shower chair 2410 Typical double bed to riser recliner chair User Guide Servicing and Maintenance Based upon EN10535 1998 and Health and Safety Executive guidance Chiltern Invadex recommend that hoists and gantry systems are fully serviced including a load test at least every 12 months with an interim six monthly inspection to LOLER requirements Prices are available from Chiltern Invadex Service Offices The frequency of servicing should be increased in areas where the environment or heavy usage may cause deterioration of the equipment Further details can be obtained from any Chiltern Invadex Office shown on the back of this booklet Chiltern Invadex and its Authorised Dealers are able to carry out all aspects of servicing and maintenance work Maintenance of this equipment should only be conducted by engineers trained and certified by Chiltern Invadex Keep the service record at the back of this booklet up to date DO NOT USE IF 1 There is any damage to the hoist or gantry 2 There is fraying or stitch damage to the lifting tape or slings 3 Any of the gantry parts are missing or damaged To ensure maximu
Download Pdf Manuals
Related Search