Sol 3000 User Guide
Contents
1. ary ff 7 E ia Solar Panel Battery Visual Beacon Oil Interceptor EMC Emissions Immunity LVD Test Reset Button Fuse 2A 20mm Enclosure Dimensions Overall Assembled Height Assembled Weight SOL3000 Int Specification eptor Alarm gt ae a a Ei r y A a e D I j a l AN om E S y j n a F q w j 5 A D E N a y 4 bos D mes T80 530 Che level people Issue 7 13 07 2006 Output 16V maximum 12V nominal 500mA maximum connected to battery via solar shunt regulator 16AH lead acid re chargeable maximum voltage from solar panel 13 8V via over voltage protection provided by solar shunt regulator Flash rate 1Hz Alarm Unit intrinsically safe certified 12V DC unit VTT 02 ATEX 012X EN 61000 3 EN 61000 2 EN 61010 1 IP67 mounted on side of enclosure In Test Mode the button simulates an alarm condition and energises the visual beacon In Reset mode the Green LED on alarm unit and flashing beacon come on for 20 seconds and then go off providing fault condition has been cleared During transportation the fuse should be removed to de energise the system and conserve battery power Polycarbonate PC ABS with transparent and lockable door IP65 Electronic Enclosure 400mm x 300mm x 200mm deep 1 6 metres 27 OK0 AFRISO EUROGAUGE LTD Imberhorne Lane East Grinstead West Sussex RH19 1RF Uni2. l stop flashing If the probe is not immersed in water then after fitting the fuse the green power LED the red alarm LED and the flashing beacon will come on After 20 seconds the green LED and the red alarm LED will go out but the beacon will continue to flash until the separator is filled to normal level with water Press the Test Reset button and check that the green power LED on the alarm unit comes on that the red alarm LED is lit and that the beacon is flashing Fuse Holder Position The system is now fully operational Maintenance and Test lt is recommended that the transparent cover of the electronics housing is periodically cleaned with a suitable cleaner antistatic to ensure that the solar panel always receives enough light to keep the bat tery fully charged The Test Reset button should be operated at least once a month to ensure that the system is in full working order When a separator oil alarm condition is being cleared the probe should be removed from the separator turret cleaned and replaced When the oil has been drained from the separator and refilled with water the Test Reset button should be operated The Green LED and the flashing beacon will come on for 20 seconds and then go off The unit is now fully operational Base Flange Fixing Hole Details 145 PCD 13 0 E 34 0 Section through A A 185 0 PCD 3 4
3. rbon in oil separators interceptors in locations where mains power is unavailable The system comprises an IP65 electronics housing containing the solar powered circuitry with an integral 10 metre cable extendable to 300 metres and a fail safe sensor with no moving parts for mounting in the separator chamber A high intensity flashing beacon warns that the separator requires emptying 1 4 User Guide EUROGAUGE SOL3000 Interceptor Alarm ane the level people Operation An integral solar panel trickle charges a heavy duty lead acid 16AH battery which powers an intrinsically safe certified separator alarm unit A Test Reset button is provided that checks the correct functioning of the system by simulating an alarm condition When the separator has been cleaned the system can be reset by pressing the Test Reset button The system will self check for 20 seconds beacon flashing before returning to the normal condition To conserve battery power and prolong operating life the alarm unit is activated for 20 seconds every 60 minutes If an alarm condition is present the high intensity beacon will flash and continue to do so until the alarm condition is cleared The battery has capacity for the unit to operate the beacon continuously for 7 days in poor light conditions Installation Prior to installation the site contractor should provide a suitable concrete base with correctly spaced mounting studs set into the concrete ba
4. se Insert the sensor into the separator using the access point provided by the separator manufacturer Under normal working conditions the sensor needs to be completely covered with water Run wires through a suitable duct to the junction box in the separator turret Orientate the pole until the solar panel is facing south Mount the complete assembly onto the concrete base and secure the fixing nuts Connect the wires from the unit to the junction box in the separator turret as per diagram below The green earth wire should be connected to the separator earth where provided on the separator Wiring Diagram Cable to SOL 3000 Terminal Box Cable Connections 7 f mG 2x0 5mm ZA Black 1 r jj 10mlong tify Black 2 2 Mey Safe Area Yi tty UMD Mees Mey Hazardous Area Hy yy Ground UM Mek Meh ML My My Mey Terminal Box IP67 Y 000 in Separator Turret NaN IN AN A Ground Terminal BoxCable Connections Wire 1 amp 3 1 Wi ire 2 S INNS SNNN SINSA NSAN AAAA NN N TARL QQ QQ QQ QQ QA QO 2D OQ QO OOQOOROQMCOQOQOQAOQAL Cable to probe in Separator 4 N tt QQ QQ N N 2 4 User Guide SOL3000 Interceptor Alarm EVROGAUGE A ail the level p cople Issue nate Commissioning lf the probe is immersed in water then after fitting the fuse the green power LED and the flashing beacon will come on After 20 seconds the green LED will go out and the beacon wil
5. ted Kingdom Tel 44 0 1342 323641 Fax 44 0 1342 315513 www eurogauge co uk sales eurogauge co uk RADAR and MICROPULSE ULTRASONICS PRESSURE TRANSMITTERS VIBRATION SWITCHES CAPACITANCE Float Level Switches Conductivity Rotary Paddle and Plumb bob Magnetostrictive Self powered gauges Oil water Alarms Leak Detectors Pressure and Temperature Declaration of Conformity SOL 3000 Oil Interceptor Alarm This is to certify that the above named product fully complies with the Electromagnetic Compatability Directive 89 336 EEC and the Low Voltage Directive 73 23 EEC of the European Union and with the requirements of the normative sections of the following harmonised European Standards EN61000 3 Electromagnetic Compatibility Generic Emission Standard Residential Commercial and Light Industry EN61000 2 Electromagnetic Compatibility Generic Immunity Standard Heavy Industry EN61010 1 Safety requirements for electrical equipment for measurement control and laboratory use Signed Ce ma D C Ward Position Technical Services Manager Date 13 07 2006 This declaration applies to the following part number s 2830 00 0000 4 4 the level people T80 530 Issue 7 13 07 2006 en Fo Ef g b P P N aa_w a g I i E Ba i k a E E J ji ae bY y A N y l T wey i SOL3000 Interceptor Alarm OSET 1000 The SOL 3000 is designed to monitor the level of liquid hydroca
Download Pdf Manuals
Related Search