USER GUIDE - BestStuff.co.uk
Contents
1. be used in another zone with a higher number but not in a lower number zone You MUST ensure that your mains electricity supply is isolated before commencing installation gt gt gt ceiling unzoned Please Note Installation in bathrooms en suites or similar rooms must be installed by a qualified electrician in accordance with IEE wiring regulations and conform to BS7671 and Part P of the Building Regulations The information above is intended as a guide only For detailed information refer to the IEE wiring regulations Installation Infrared heaters are ideal for heating specific areas or zones They operate by radiating infrared light that heats the objects and walls in a room and not the surrounding air Therefore it is important that your panel is positioned so that the rays of infrared light are unobstructed and reach as much of the room as possible For optimum heating the panel should be mounted at least 1 2m above ground level Make sure the surface on which you are mounting the heater panel is strong enough to support the weight of the panel All walls differ in strength and thickness use fixings suitable for your type of mounting surface to mount the wall brackets Fixings are not supplied consult a suitable professional for guidance if you are unsure which fixings to use a M6x30 Screw pra Wall Bracket Step 1 Measure up the mounting surface as shown opposite Attach the two mounting brack2. Y Ge aN NT ECO POWER Infrared Heater USER GUIDE WARNING BEFORE INSTALLATION PLEASE READ THESE INSTRUCTIONS CAREFULLY KEEP FOR FUTURE REFERENCE ANY WIRING INSTALLATION MUST BE CARRIED OUT BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH IEE WIRING REGULATION AND CONFORMING TO PART P OF THE BUILDING REGULATIONS Philex Support Line 08457 573 479 Monday to Friday 9 00am to 5 00pm Local rate UK only C Technical Support www philex com support EEE Introduction Congratulations on the purchase of this Philex Heating product Your Infrared Heating Panel is manufactured from high quality materials and should give you many years of service To guarantee that your product functions correctly there are some key points described in these installation instructions which must be followed The electrical installation must be carried out by a qualified electrician in accordance with IEE Wiring Regulations and conform to BS7671 and Part P of the Building Regulations If you have any questions or require more information then contact the Philex Support Line 08457 573 479 Monday to Friday 9 00am to 5 00pm Contents Product SpecificatiOhsssnssniienendnusnineni miann ena a a 2 Pack Contents Important DoS amp DOMES isvicccscccecrssssesscciesssccesviewseossiceceazsecsssdtesnssdevstatveussvicentudeosecdistnbedenvieweansvteerszceassedie 4 Preparati sasssssscesssosssissnssussassssesnssiseciecss cssdesens es vaszeaeeassso
3. ets securely using appropriate fixings 1 2 1 8m Step 2 Assemble the 4 hanging M6 x 30 screw buttons washers and M6 x 30 ee screws as shown below Hanging Buttons Step 3 Align the panel screws 5 with the corresponding slots in the two brackets fixed to the wall and slide the panel down into place ensuring a secure and strong hold Step 4 Wiring in your infrared heater this should be done by a qualified electrician in accordance with IEE wiring regulations and installations must conform to BS7671 and Part P of the Building Regulations Operating your Infrared Heater e Switch on the isolating switch if present turn on the power switch on the side of the panel e The temperature will be displayed in the LED window on the front of the heating panel e The Product can also be switched on and off using the remote control e When the product is first turned on it will be on the factory default setting factory default setting is 85 C users can set their preferred temperature later on e The highest temperature it can be set at is 85 C and the lowest setting is 45 C A Every time you press the up arrow button on either the side of the panel or the remote control the temperature will increase by 1 C Vv Every time you press the down arrow button on the side of the panel or the remote control the temperature will decrease by 1 C A Holding either button down continuously will increase or decrease the tempera
4. ing of the product unless you are a part P registered electrician DO NOT use petrol benzene thinner solvents or any similar chemicals to clean the panels e DO NOT let water drop directly onto the body or any electrical components e DO NOT brush any part of the panel with a wire brush or other hard object A fused spur and circuit breaker must be installed if in a bathroom or other damp location DO NOT remove any of the outer casing of the unit e DO NOT install in a sauna or steam room Installation location must not be too close to curtains or other flammable materials e The product body and the panel must be firmly installed to avoid falling e DO NOT install near a smoke generator e DO NOT install in an industrial environment e DO NOT touch the panel surface when in use let it cool down first Preparation General Safety The risk of accidents can be greatly reduced by careful planning before starting a project Always follow manufacturer s operating and safety instructions before using tools and or equipment Before starting installation check structure is sound and check for hidden electrical wiring or plumbing Before making any connections switch electricity off at the mains amp fuse box We have not supplied wall fixings with this product All walls differ in strength and thickness and you will need to purchase suitable screws and wall plugs designed specifically for your type of mounting surface If in doub
5. seacianeadsoasedesnsensionssdssastoachostongaevasstvsdsasnanesvtasssoieaed 4 EEEO AEE ES EE EEE E EET SEET 5 6 Bathroom Zoning Positioning Your Heating Panel ssssscsssessecsssseceseessessseecsseesssseeeessneesssees 5 Wall Mounting Your Heating Panel ssesscsssssccssssscsnsssessescsnssscesssscesnssessnssscesaseessnseecesueessnseessnaneeed 6 Operating Your Heating Panel un sssssscssssscesseccsnssecsnssccessseecsnseeeesusscssnseessnssecesusessnseecesneessnseessnaeeees 7 Product Specifications Operating Voltage 220V 240V User Temperature setting range 45 C 85 C Max Rated Power heating continuously less than 260W On Off switch e Degree of housing protection from liquids and dust IP44 Panel Dimensions 800 x 600 x 50mm e Gross Weight 15 5kg Pack Contents ogggugog af S 1 2 1 8m PE PAIPP GP Oa ue PAPPP AAR d 1 Infrared Heating Panel with mirrored front and LED 2 Wall brackets 2 Pcs 3 Hanging buttons 4 Pcs 4 Washers 4 Pcs 5 M6 x 30 screws 4 Pcs 6 Remote Control 7 User Guide Fixed Installation Accessories T Wall Bracket Hanging Button M6 x 30 Screw Important Do s amp Don ts e Confirm that the contents of the box are correct e Read this User Guide IN FULL before starting work e DO NOT cut corners with preparation or installation Do use a qualified Electrician if any electrical work is carried out DO NOT attempt any electrical wir
6. t we advise you to consult a professional builder for guidance Installation in bathrooms en suites or similar rooms must be installed by a qualified electrician in accordance with IEE wiring regulations and installations must conform to BS7671 and Part P of the Building Regulations When the product is not in use please turn off the power switch to save electricity and to extend your product s life When switched off the temperature display and backlight lamp settings will be automatically stored to memory These settings will be automatically restored when the panel is switched on again The Front panel will become hot when in use to avoid burns and scalds DO NOT TOUCH and keep children away This equipment has been designed to be used by adults So please make sure that children do not go near the equipment or play with it while the appliance is running Before carrying out any maintenance or cleaning of the panel switch power supply off and let it cool down Installation Bathroom Zones The IP Rating indicates the amount of Ingress Protection and refers to water particle ingress The IP rating will determine where you can safely position your infrared heating panel Your infrared heating panel has been specially protected against the ingress of moisture and is manufactured to meet IP44 standards thereby making it suitable for installation in Zone 2 and 3 of your Bathroom Any electrical item approved for use in a zone may
7. ture Y by 1 C every 0 5 seconds The LED back lights come on automatically when the power is switched on Use the Light on off switch on the side of the panel or the remote to switch them on off Powerswitch a ight on ott Using your Remote Control l Your infrared heating panel comes with a remote control for your added convenience The remote has four buttons which correspond with the controls on the side of the heating panel To control your heater using your remote aim the remote at the temperature display window on the front of the heating panel e The POWER button turns the panel on off Press the remote TEMPERATURE button to increase the temperature by 1 C Press the W button to decrease the temperature by 1 C Holding either button down continuously will increase or decrease the temperature by 1 C every 0 5 seconds e The LIGHT button will turn the LED back lights on off heater Ga HEATING For further information please contact Philex Customer Careline on 08457 573 479 Monday to Friday 9 00am to 5 00pm Local rate UK only Technical Support www philex com support Waste electrical and electronic products must not be disposed of with household waste Please recycle where facilities exist Check with your Local Authority for recycling advice Philex Electronic Ltd 2010 v1 www philex com Dp EE oo7 EEOO
Download Pdf Manuals
Related Search