Operating instructions
Contents
1. dH hardness measured in German degrees f hardness measured in French degrees mmol l millimoles per litre Measuring out the refined salt In order to achieve the best possible results using a wash cycle make sure that the dispenser is never empty Refined saltremoves limescale from the water thus avoiding the formation of deposits on crockery The salt dispenser is located in the lower part of the dishwasher see Description and should be filled e When the green float cannot be seen by simply looking at the cap of the salt dispenser e When the LOW SALT indicator light on the control panel is illuminated 1 Remove the lower rack and unscrew the container cap anticlockwise 2 The first time you do this fill the water tank right up to its edge 3 Position the funnel see figure and fill the salt container right up to its edge this should hold approximately 1 kg it is not unusual for a little water to leak out 4 Remove the funnel and wipe any salt residue away from the opening rinse the cap under running water and then screw it on the head facing downwards so as to let the water flow out of the four cracks which are arranged in a star shape on the lower part of the cap Salt cap with green float It is advisable to perform this procedure every time you add salt to the container Make sure the cap is screwed on tightly so that no detergent can get into the container during t2. To remove the upper sprayer arm rotate the locking ring in an anti clockwise direction The upper sprayer arm should be replaced with the holes facing upwards HA IN gii al AE ULA Yo L V The lower sprayer arm can be removed by pressing on the side tabs and pulling it upwards Cleaning the water inlet filter If the water hoses are new or have not been used for an extended period of time let the water run to make sure it is clear and free of impurities before performing the necessary connections If this precaution is not taken the water inlet could become blocked and damage the dishwasher MAZZI UN I TD Scholtes Clean the water inlet filter at the tap outlet regularly Unscrew the end of the water inlet hose remove the filter EN Turn off the water tap clean it carefully under running water Replace the filter and screw the water hose back into position Cleaning the filters The filter assembly consists of three filters which remove food residues from the washing water and then recirculate the water They should be cleaned if you wish to achieve the best results in every wash Clean the filters regularly The dishwasher should not be used without filters or if the filter is loose e After several washes check the filter assembly and if necessary clean it thoroughly under running water using a non metallic brush and following the instructions
3. 16
4. Switch off the appliance by pressing the ON OFF button and switch it back on after one minute If the alarm continues shut off the water tap to eliminate the risk of flooding remove the plug from the electrical socket and contact Assistance Switch off the appliance by pressing the ON OFF button Shut off the water tap to eliminate the risk of flooding and remove the plug from the electrical socket Make sure the water inlet filter has not become blocked by various impurities see Care and maintenance chapter 13 Scholt s UK Morley Way Peterborough PE2 9JB t 0800 158 55 00 e info scholtes co uk w Scholtes co uk COMMITMENT TO AFTER SALES SUPPORT THANK YOU FOR INVESTING IN SCHOLTES Scholt s products are designed to perform consistently and reliably throughout their life To give you further reassurance Scholt s ensures your appliance benefits from a five year guarantee This promise means that if within five years from the date of purchase of your appliance it is proven to be defective Scholt s will at its discretion repair or replace the appliance at no additional cost CONTACT There is a dedicated team of advisors to provide free advice and assistance with any problem you experience with a Scholt s appliance Where necessary Scholt s will arrange for an engineer from its specialist field support team to resolve the issue with the least disruption TELEPHONE FREE ON 0800 158 55 00 To help manage potential p
5. play with the appliance e The appliance was designed for domestic use inside the home and is not intended for commercial or industrial use e The appliance must be used by adults only to wash domestic crockery in accordance with the instructions in thismanual e The appliance must not be installed outdoors even in covered areas It is extremely dangerous to leave the machine exposed to rain and storms e Donottouch the appliance when barefoot e Vhen unplugging the appliance always pull the plug from the mains socket do not pull on the cable e The water supply tap must be shut off and the plug should be removed from the electrical socket before cleaning the appliance or carrying out any maintenance work e fthe appliance breaks down do not under any circumstances touch the internal parts in an attempt to perform the repair work yourself e Nevertouch the heating element e Donotlean or sit on the open door of the appliance this may cause the appliance to overturn e The door should not be left open as it may create a dangerous obstacle e Keep detergent and rinse aid out of reach of children e The packaging material should not be used as a toy Disposal e Disposal of packaging materials observe local legislation so that the packaging may be reused e The European Directive 2002 96 EC relating to Waste Electrical and Electronic Equipment WEEE states that household appliances should not be disposed of using the norma
6. 3 Daily A 60 lt D mn 6 Rapid 7 Crystal 8 Auto Duo Wash Options table 9 Ultra Intensive 10 Special Guest l Only available in selected models O jo o o o JO Z O z z x 212 1212 215 ds o jo P lo o jo jo o B P ZI Wash cycles ME Scholtes For available OPTIONS please refer to the Table of options on the Start up and use page The number and type of wash cycles and options may vary depending on the dishwasher model Detergent Wash Wash cycle A compartment A Cycles duration Wash cycle B compartment B which tolerance dui include 10 Heavily soiled dishes and pans not to be used for delicate items A 35 ml A Normally soiled pans and dishes Standard daily wash cycle Wash cycle selection instructions 2 25 O al Q N e Q O Q Limited quantity of daily soiling 4 place settings 1 saucepan 1 frying pan Pre wash for dishes while awaiting completion of the load with the dishes from the next meal Environmentally friendly wash cycle with low energy consumption levels suitable for pans and dishes Economic and fast wash to be used for lightly soiled dishes Run cycle immediately after use 2 plates 2 glasses 4 pieces of cutlery 1 saucepan 1 small frying pan Economic and fast wash for delicate items which are sensitive to high temperatures Run cycle immediately after use glasses upper r
7. YO IA ba LASA PV The modular basket may be separated into two parts a solution which is a recommended when gt y CHE m performing a half load wash only in models offering this option is available in a sliding version positioned at any point on the lower rack by sliding it between the fixed or tip up inserts Both versions are fitted with a collapsible sliding system which means the cutlery can be arranged in the best possible way oopbmnoo 0000000 OOOO00DO D Knives and other utensils with sharp edges must be placed in the cutlery basket with the points facing downwards or they must be positioned horizontally in the tip up compartments on the upper rack Cutlery basket positioning examples Gain A IE SAAB de AAAA Ni alla gi V ANNAN NN EN EEEN N Gin m w a oo ey e SS oo HE Li L e E Q V Upper rack Load this rack with delicate and lightweight crockery glasses tea and coffee cups saucers small salad bowls saucepans and small saucepans which are not too soiled using the Loading examples as a guide e Mugs and cups long sharp knives and serving utensils place these on the tip up compartments Tip up compartments with adjustable tilt The tilt feature can be used to increase
8. below 1 Turn the cylindrical filter C in an anti clockwise direction and pull it out fig 1 2 Remove the cup filter B by exerting a slight pressure on the side flaps fig 2 3 Slide out the stainless steel plate filter A fig 3 4 Inspect the trap and remove any food residue NEVER REMOVE the wash cycle pump black detail fig 4 After cleaning the filters replace the filter assembly and fix it in position correctly this is essential for maintaining the efficient operation of the dishwasher Leaving the machine unused for extended periods e Disconnect the appliance from the electricity supply and shut off the water tap e Leave the door of the appliance ajar e When you return run a wash cycle when the dishwasher is empty Only available in selected models 11 Precautions advice and Assistance This appliance was designed and manufactured in compliance with current international safety standards The following information has been provided for safety reasons and should therefore be read carefully General safety e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety e Children should be supervised to ensure that they do not
9. device to a lower number 1 3 e f drops of water remain on the crockery or if there are limescale marks present after the cycle has finished set the adjuster to a higher number 4 6 Setting the water hardness Every dishwasher is equipped with a water softener which by using refined salt designed especially for this type of appliance supplies water without limescale which is then used to wash the crockery This dishwasher offers a setting which helps to reduce pollution and optimises washing performance in accordance with the water hardness level in your area This information can be obtained from the organisation which supplies your household with water Open the door and switch on the machine by pressing the ON OFF button Press the P button and hold for approximately 5 seconds two short beeps will sound and the set hardness number will flash slowly on the display the water softening system is set to number 3 10 Press the P button repeatedly until the desired hardness level has been reached 422 3 4 5 see Water hardness table To exit the function wait a few seconds or press one of the option buttons or switch off the machine using the ON OFF button Even if using multi functional tablets the salt dispenser should still be filled Water Hardness Table For values between O f and 10 f we do not recommend the use of salt this setting may cause a slight increase in the duration of the cycle
10. the space in the upper rack to position wine glasses with different stem lengths safely and to improve drying performance Lift the tip up compartment slide it gently and position it in the desired tilt angle Adjusting the height of the upper rack In order to make it easier to arrange the crockery the upper rack may be moved to a higher or lower level The height of the upper rack should ideally be adjusted WHEN THE RACK IS EMPTY Never lift or lower the rack on one side only Open the left and right guide rail stops and pull out the rack position it higher or lower as required slide it along the guide rails until the front wheels are in place and close the stops see figure If the rack is fitted with Dual Space handles see figure pull out the upper rack until itreaches its stop point grip the handles at the sides of the rack and move it upwards or downwards then slowly let it fall back into place Loading examples for the upper lower rack Items which should not be washed in the dishwasher e Wooden items objects with wooden or horn handles or glued on parts e ltemsmade from aluminium copper brass pewter or tin e tems made from plastic material which is not heat resistant e Antique or hand painted porcelain e Antique silver Silver which is not antique may however be washed in the dishwasher using a delicate wash cycle provided that it does not come into contact with othe
11. water hoses or the electricity supply cable The appliance must be connected to the water supply network using new hoses Do not use old hoses The water inlet A and outlet B hoses and the electricity supply cable may be positioned towards the right or the left in order to achieve the best possible installation see figure 115 130 127 115 Connecting the water inlet hose e Toa suitable cold water connection point before attaching the hose run the water until it is perfectly clear so that any impurities that may be present in the water do not clog the appliance after performing this operation screw the inlet hose tightly onto a tap with a gas threaded connection e oa suitable hot water connection point your dishwasher may be supplied with hot water from the mains supply if you have a central heating system with radiators provided that it does not exceed a temperature of 60 C Screw the hose to the tap as described for connection to a cold water supply If the inlet hose is not long enough contact a specialist store or an authorised technician see Assistance The water pressure must be within the values indicated in the Technical data table see adjacent information The hose should not be bent or compressed Anti flooding protection To ensure floods do not occur the dishwasher is provided with a special system which blocks the water supply in the event of anomalies or leaks from inside the app
12. Night ANNI E option button PI 3h 6h9h gt ua PY Option button Short Time ON OFF Reset Low salt button indicator light Multi functional tablets button Wash cycle number light up indicator Half load button a Delayed start Delayed start button indicator lights Only in completely built in models Only available in selected models The number and type of wash cycles and options may vary depending on the dishwasher model Loading the racks Before loading the racks remove all food residues from the crockery and empty liquids from glasses and cups After loading the appliance check that the sprayer arms can rotate freely Lower rack The lower rack can hold pans lids plates salad bowls cutlery etc as seen in the Loading examples Plates and large covers should be placed at the sides of the rack ensuring that they do not block the rotation of the upper sprayer arm some dishwasher models are fitted with tip up sections which can be used in a vertical position when arranging plates or in a horizontal position when arranging pans and salad bowls Cutlery basket The type of cutlery basket may vary according to the dishwasher model it may be modular non modular or a sliding version The non modular basket must only be positioned at the front of the lower rack 4 LA A A a YE O YO lt Y A A RY AN AS K INN DA
13. Operating instructions English 1 SW14DPPAI MUY S S 2 gt AaS Scholt s DISHWASHER Contents Installation 2 3 4 Positioning and levelling Connecting the water and electricity supplies Advice regarding the first wash cycle Technical data Electrical connection Description of the appliance 5 Overall view Control panel Loading the racks 6 Lower rack Cutlery basket Upper rack Start up and use 7 8 Starting the dishwasher Measuring out the detergent Wash options Wash cycles 9 Table of wash cycles Rinse aid and refined salt 10 Measuring out the rinse aid Measuring out the refined salt Care and maintenance 11 Shutting off the water and electricity supplies Cleaning the dishwasher Preventing unpleasant odours Cleaning the sprayer arms Cleaning the water inlet filter Cleaning the filters Leaving the machine unused for extended periods Precautions advice and Assistance 12 General safety Disposal Saving energy and respecting the environment Before contacting Assistance Troubleshooting 13 Commitment to after sales support 14 Installation Keep this instruction manual in a safe place for future reference If the appliance is sold given away or moved please ensure the manual is kept with the machine so that the new owner may benefit from the advice contained within it Please read this instruction manual carefully it contains important information regarding the saf
14. Possible causes Solutions The dishwasher does not start e The plug has not been inserted into the electrical socket properly or there is no power in the house e The dishwasher door has not been shut properly e A delayed start has been programmed see Start up and use No water drains out from the dishwasher The dishwasher makes excessive noise The dishes and glasses are covered in a white film or limescale deposits The dishes and glasses are streaked or have a bluish tinge The crockery has not been dried properly The dishes are not clean The dishwasher does not take any water in Tap shut off alarm several short beeps are emitted the ON OFF indicator light flashes and the number 6 appears on the display Water intake solenoid valve malfunction alarm the ON OFF indicator light flashes and the number 2 appears on the display Water inlet hose alarm Water inlet filter blocked the ON OFF indicator light flashes and the number 7 appears on the display The dishwasher cycle has not yet finished The water outlet hose is bent see nstallation The drain duct is blocked The filter is clogged up with food residues The dishes are rattling against each other or against the sprayer arms An excessive amount of foam has been produced the detergent has not been measured out correctly or it is not suitable for use in dishwashers see Start up and use The level of the refine
15. ack delicate plates lower rack Wash spread over the two racks delicate for crystal and glasses on the upper rack and heavy duty for 35 g A the pans on the lower rack Heavily soiled saucepans or pans 35 q A 1 bottom with residual dried on food 5 E B of the appliance N O N O de A W N PS oO On al al Q al al 00 Q Q Rinse and drying cycle for dishes that are seldom used and are only dusty Yes A B 0 32 Notes Optimum performance levels when using the Daily A 60 and Rapid wash cycles can be achieved by observing the maximum amounts of crockery specified To make it easier to measure out the detergent it is worth remembering that 1 tablespoon 15 grams of powder approximately 15 ml of liquid 1 teaspoon 5 grams of powder approximately 5 ml of liquid The Bio wash cycle adheres to the regulation EN 50242 Although it has a longer duration than other wash cycles it uses less energy and is les harmful to the environment Note for Test Laboratories for information relating to comparative EN testing conditions please send an email to the following address ASSISTENZA_EN_LVS indesitcompany com Z O O Disinfecting cycle for cleaning the inside of the dishwasher to be carried out only when the dishwasher is EMPTY using EN specific detergents designed for dishwasher maintenance 11 Self Care KAD O O KA O ES O a N Q Rinse aid and refined s
16. alt Only use products which have been specifically designed for dishwashers Do not use table salt or industrial salt or washing up liquid Follow the instructions given on the packaging If using a multi functional product it is not necessary to add rinse aid however we recommend that you add salt especially if you live in an area where the water is hard or very hard Follow the instructions given on the packaging If you do not add salt or rinse aid the LOW SALT and LOW RINSE AID indicator lights remain lit Measuring out the rinse aid Rinse aid makes it easier for the crockery to dry as water runs off surfaces more readily and therefore does not leave streaks or marks The rinse aid dispenser should be filled e When the LOW RINSE AID indicator light on the control panel is illuminated 1 Open the dispenser by turning the lid G in an anticlockwise direction 2 Pour in the rinse aid making sure it does not overflow from the dispenser If this happens clean the spill immediately with a dry cloth 3 Screw the lid back on NEVER pour the rinse aid directly into the appliance tub Adjusting the amount of rinse aid If you are not completely satisfied with the drying results you may adjust the quantity of rinse aid used Use a screwdriver to turn the dosage adjuster F to one of the 6 ore set positions the default position is set to 4 e f there are streaks on the crockery set the adjustment
17. ccordingly The duration of the auto wash cycles may vary due to the operation of the sensor If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher reduce the amount of detergent used accordingly Modifying a wash cycle in progress If a mistake was made during the wash cycle selection process it is possible to change the cycle provided that it has only just begun open the door avoiding the escaping steam and press and hold the ON OFF button the machine will switch off with a long beep Switch the machine back on using the ON OFF button and select the new wash cycle and any options desired start the cycle by closing the door Adding extra crockery Without switching off the machine open the door taking care to avoid the escaping steam and place the crockery inside the dishwasher Close the door the cycle starts from the point at which it was interrupted Accidental interruptions If the door is opened during the wash cycle or if there is a power cut the cycle stops It starts again from the point at which it was interrupted once the door has been shut or once the electricity supply is restored I ZI MY si I TD Scholtes Measuring out the detergent A good wash result also depends on the correct amount of detergent being used exceeding the stated amount does not result in a more effective wash and increases environmental pollution Only use deter
18. d N or coloured Black If a 13 amp plug BS 1363 is used it must be fitted with a 13 amp fuse A15 amp plug must be protected by a 15 amp fuse either in the plug or adaptor or at the distribution board If you are in any doubt about the electrical supply to your machine consult a qualified electrician before use How to connect an alternative plug The wires in this mains lead are coloured in accordance with the following code BLUE NEUTRAL N BROWN LIVE L GREEN AND YELLOW EARTH E or GREEN amp 13 amp fuse CROSS BAR CORD GRIP Disposing of the appliance When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described above ZI Wi si Description ofthe MM appl lance Scholt s Overall view Upper rack Upper sprayer arm Tip up compartments Rack height adjuster Lower rack Lower sprayer arm Cutlery basket Washing filter salt dispenser 10 Detergent and rinse aid dispensers 11 Data plate 12 Control Panel oe G DA ee SE K K Control panel Multi functional tablets Low rinse aid indicator light indicator light Half load upper rack indicator light Short Time option Select wash indicator light cycle button sitio 7 nalt load lower rac Good Night option ae ice light indicator light indicator light Good
19. d salt is low or the dosage setting is not suited to the hardness of the water see Rinse aid and salt The lid on the salt dispenser is not closed properly The rinse aid has been used up or the dosage is too low The crockery is made from non stick material The rinse aid dosage is too high A wash cycle without a drying programme has been selected The rinse aid has been used up or the dosage is too low see Rinse aid and salt The rinse aid dispenser setting is not high enough The racks are overloaded see Loading the racks The crockery has not been arranged well The sprayer arms cannot move freely The wash cycle is too gentle see Wash cycles An excessive amount of foam has been produced the detergent has not been measured out correctly or it is not suitable for use in dishwashers see Start up and use The lid on the rinse aid compartment has not been shut correctly The filter is dirty or blocked see Care and maintenance The refined salt level is low see Rinse aid and salt There is no water in the mains supply The water inlet hose is bent see nstallation Turn on the tap and the appliance will start after a few minutes The appliance lock has been activated because no action was taken when the beeps sounded Switch off the machine using the ON OFF button turn on the tap and switch the machine back on after 20 seconds by pressing the same button Re programme the machine and restart the wash cycle
20. e installation use and maintenance of the appliance If the appliance must be moved at any time keep it in an upright position if absolutely necessary it may be tilted onto its back Positioning and levelling 1 Remove the appliance from all packaging and checkthat it has not been damaged during transportation If it has been damaged contact the retailer and do not proceed any further with the installation process 2 Check the dishwasher by placing it so that its sides or back panel are in contact with the adjacent cabinets or even with the wall This appliance can also be recessed under a single worktop see the Assembly instruction sheet 3 Position the dishwasher on a level and sturdy floor If the floor is uneven the front feet of the appliance may be adjusted until it reaches a horizontal position If the appliance is levelled correctly it will be more stable and much less likely to move or cause vibrations and noise while it is operating 4 Adjust the height of the rear foot from the front of the i appliance on the central lower part of the dishwasher turning a hexagonal spanner red color with an opening of 8mmina clockwise direction to increase the height or in an anticlockwise direction to decrease the height Connecting the water and electricity supplies Connection to the water and electricity supplies should only be performed by a qualified technician The dishwasher should not stand on top of the
21. gent which has been specifically designed for dishwashers DO NOT USE washing up liquid Using excessive detergent may result in foam residue remaining in the machine after the cycle has ended The use of tablets is only recommended for models which offer the MULTI FUNCTIONAL TABLETS option To achieve the best results from each washing and drying cycle powder detergent rinse aid liquid and salt should be used Compartment A Washing detergent Compartment B Pre wash detergent 1 Open cover C by pressing button D 2 Pour in the detergent after consulting the Table of wash cycles e For powder detergent use compartments and B e For detergent in tablet form when the cycle requires 1 tablet place it in compartment A and close the cover when it requires 2 place the second tablet at the bottom of the appliance 3 Remove detergent residues from the edges of the compartment and close the cover until it clicks li Only available in selected Models Wash options If an option is not compatible with the selected was cycle see Table of wash cycles the corresponding LED flashes rapidly 3 times and 2 short beeps will sound Delayed start It is possible to delay the start time of the cycle by 3 6 or 9 hours 1 Press the DELAYED START button every time it is pressed a buzzer sounds and the selected period of time is displayed 2 Select the wash cycle and shut the door after the beep sounds the time
22. he wash cycle this could damage the water softener beyond repair When necessary measure out the salt before a wash cycle so that any saline solution which has leaked out of the salt dispenser is removed l Only available in selected models Care and maintenance gt Shutting off the water and electricity supplies e Turn off the water tap after every wash cycle to avoid leaks e Always unplug the appliance when cleaning it and when performing maintenance work Cleaning the dishwasher e The external surfaces of the machine and the control panel may be cleaned using a non abrasive cloth which has been dampened with water Do not use solvents or abrasive products e Any marks on the inside of the appliance may be removed using a cloth dampened with water and a little vinegar Preventing unpleasant odours e Always keep the door of the appliance ajar in order to avoid moisture from forming and being trapped inside the machine e Clean the seals around the door and detergent dispensers regularly using a damp sponge This will avoid food becoming trapped in the seals which is the main cause behind the formation of unpleasant odours Cleaning the sprayer arms Food residue may become encrusted onto the sprayer arms and block the holes used to spray the water It is therefore recommended that the arms are checked from time to time and cleaned with a small non metallic brush The two sprayer arms may both be removed
23. in the lengthening of the wash cycle The MULTI FUNCTIONAL TABLETS option remains set for subsequent wash cycles if it is not deselected The use of tablets is only recommended for models which offer the MULTI FUNCTIONAL TABLETS option This option is not recommended for use with wash cycles which do not specify the use of multi functional tablets see Table of options Short Time option This option can be used to reduce the duration of the main wash cycles while maintaining the same washing and drying performance levels After selecting the wash cycle press the Short Time option button the illumination of the corresponding indicator light followed by a short beep indicates its selection To deselect the option press the same button again Good Night option This option reduces the amount of noise made by the machine and lengthens the wash cycles It is a useful option because it enables users to benefit from the night time energy rate After selecting the wash cycle press the Good Night option button the illumination of the corresponding indicator light followed by a short beep indicates its selection To deselect the option press the same button again The Short Time and Good Night options are not compatible with each other The Short Time and Good Night options are not compatible with the HALF LOAD option Vv gt O ZO O O o daddi o jo Q lo zi 3 O O gt 1 Auto Super Wash 2 Auto Normal
24. l solid urban waste cycle Exhausted appliances should be collected separately in order to optimise the cost of re using and recycling the materials inside the machine while preventing potential damage to the atmosphere and to public health The crossed out dustbin is marked on all products to remind the owner of their obligations regarding separated waste collection For further information relating to the correct disposal of household appliances owners may contact the relevant public authority or the local appliance dealer 12 Saving energy and respecting the environment Saving water and energy e Only begin a wash cycle when the dishwasher is full While waiting for the dishwasher to be filled prevent unpleasant odours using the Soak cycle see Wash cycles e Selectawash cycle which is suited to the type of crockery and to the soil level of the crockery using the 7ab e of wash cycles For dishes with a normal soil level use the Eco wash cycle which guarantees low energy and water consumption levels If the load is smaller than usual activate the Half load option see Start up and use e fyour electricity supply contract gives details of electricity saving time bands run wash cycles during the periods when a lower tariff is applied The Delayed start button see Start up and use helps you organise the wash cycles accordingly Phosphate free and chlorine free detergents containing enzymes e Ve strongly reco
25. liance some models are also equipped with the supplementary safety device New Acqua Stop which guarantees anti flooding protection even in the event of a supply hose rupture h WARNING HAZARDOUS VOLTAGE Under no circumstance should the water inlet hose be cut as it contains live electrical parts di Only available in selected models Connecting the water outlet hose Connect the outlet hose without bending it to a drain duct with a minimum diameter of 4 cm Alternatively rest itover a sink or tub the free end of the hose should not remain immersed in water The special plastic elbow makes it easier to find the best layout fix the elbow to the wall securely in order to prevent the outlet hose from moving and spilling the dirty water The part of the hose marked with the letter A should be between 40 and 100 cm above the ground see figure We advise against the use of hose extensions Electrical connection Before inserting the plug into the electrical socket make sure that e The socket is earthed and complies with current regulations e The socket can withstand the maximum load of the appliance which is indicated on the data plate located on the inside of the door see chapter entitled Description of the appliance e The power supply voltage falls within the values indicated on the data plate on the inside of the door e Thesocketis compatible with the plug of the appliance If this is not
26. mmend that you use detergents that do not contain phosphates or chlorine as these products are harmful to the environment e Enzymes provide a particularly effective action at temperatures around 50 C and as a result detergents containing enzymes can be used in conjunction with low temperature wash cycles in order to achieve the same results as a normal 65 C wash cycle e o avoid wasting detergent use the product in appropriate quantities based on the manufacturer s recommendations the hardness of the water and the soil level and quantity of crockery to be washed Even if they are biodegradable detergents contain substances which may alter the balance of nature Before contacting Assistance e Check whether the problem can be resolved using the Troubleshooting guide see roubleshooting e Restart the programme to check whether the problem has ceased to exist e l the problem persists contact the Authorised Technical Assistance Service Never use the services of unauthorised technicians Please have the following information to hand e The type of malfunction e The appliance model Mod e The serial number S N This information can be found on the appliance data plate see Description of the appliance Only available in selected models ZI Troubleshooting HE Scholtes Whenever the appliance fails to work check for a solution from the following list before calling for Assistance Malfunction
27. r begins counting down 3 Once this time has elapsed the indicator light switches off and the wash cycle begins To adjust the delay time and select a smaller period of time press the DELAYED START button To cancel it press the button repeatedly until the selected delayed start indicator light switches off The wash cycle will start automatically as soon as the door is shut Half load using the upper or lower rack If there are not many dishes to be washed a half load cycle may be used in order to save water electricity and detergent Select the wash cycle and press the HALF LOAD button repeatedly the triangle corresponding to the selected load will illuminate and the wash cycle will take place only using the upper or the lower rack Remember to load the upper or lower rack only and to reduce the amount of detergent accordingly SELFCARE WASH CYCLE This disinfecting wash cycle deep cleans the inside of the dishwasher thereby reducing the formation of bad odours WARNING The SELFCARE wash cycle should be performed as part of your dishwasher maintenance routine using special single dose products follow the instructions on the packaging while the dishwasher is EMPTY Multi functional tablets This option optimises washing and drying results When using multi functional tablets press the MULTI FUNCTIONAL TABLETS button The corresponding indicator light will illuminate The Multi functional tablets option results
28. r metals We recommend the use of crockery which is dishwasher safe Only available in selected models Kk Esos The number and position may vary Start up and use Starting the dishwasher 1 Turn the water tap on 2 Open the door and press the ON OFF button you will hear a short beep and the display and option indicator lights switch on 3 Measure out the detergent see below 4 Load the racks see Loading the racks 5 Selectthe wash cycle in accordance with the type of crockery and its soil level see Table of wash cycles by pressing the P button 6 Select the wash options see adjacent information 7 Start the wash cycle by shutting the door a long beep signals the start of the wash cycle 8 Two short beeps and one long one indicate the end of the wash cycle and the wash cycle number flashes on the display Open the door switch off the appliance by pressing the ON OFF button shut off the water tap and unplug the appliance from the electricity socket 9 Wait for a few minutes before removing the crockery in order to avoid burns Unload the racks beginning with the lower level The machine will switch off automatically during certain periods of inactivity in order to minimise electricity consumption AUTO WASH CYCLES this model of dishwasher is equipped with a special sensor which can be used to assess the level of soiling and automatically select the most efficient and economic wash cycle a
29. roblems quickly and effectively Scholt s recommends registering all appliances To register appliance telephone free on 0800 158 55 00 or visit www scholtes co uk This guarantee is subject to the following conditions e The appliance has been installed and operated correctly and in accordance with the operating and maintenance instructions e The appliance is used only on the electricity or gas supply printed on the rating plate e The appliance has been used for normal domestic purposes only e The appliance has not been altered serviced maintaned dismantied or otherwise interfered with by any person not authorised by Scholt s e Any repair work be undertaken by Scholt s or an appointed agent e Any parts removed during repair work or any appliance that is replaced becomes the property of Scholt s e The appliance is used in the United Kingdom or Republic of Ireland The guarantee does not cover e Damage resulting from transportation improper use neglet or interference or as a result of improper installation e Replacement of any consumable item or accessory These included but not limited to plugs cables batteries light bulbs fluorescent tubes and starters covers and filters e Replacement of any removable parts made of glass or plastic THE GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON DOMESTIC PREMISES 14 ZI N KA Scholt s 15 195083906 01 02 2010 Xerox Fabriano
30. s can be obtained directly from your nearest Service Depot Removing the plug Ifyour appliance has a non rewireable moulded plug and you should wish to remove it to re route the mains cable through partitions units etc please esure that either the plug is replaced by a fused 13 amp re wireable plug bearing the BSI mark of approval Or the mains cable is wired directly into a 13 amp cable outlet controlled by a switch in compliance with BS 5733 which is accessible without moving the appliance Disposing of the plug Ensure that before disposing of the plug itself you make the pins unusable so that it cannot be accidentally inserted into a socket Instruction for connecting cable to an altenative plug Important the wires in the mains lead are coloured in accordance with the following code Green amp Yellow Earth Blue Neutral Brown Live CAUTION Once the appliance has been installed the electrical plug and socket should remain accessible The Company shall not be held responsible for any incidents that occur if these regulations are not observed As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminal in your plug proceed as follows connect Green amp Yellow wire to terminal market E or coloured Green or Green amp Yellow Connect Brown wire to terminal marked L or coloured Red Connect Blue wire to terminal marke
31. the case ask an authorised technician to replace the plug see Assistance do not use extension cables or multiple sockets Once the appliance has been installed the power supply cable and the electrical socket should be easily accessible The cable should not be bent or compressed If the power supply cable is damaged it must be replaced by the manufacturer or its Technical Assistance Service in order to prevent all potential hazards See Assistance The Company shall not be held responsible for any incidents that occur if these regulations are not observed 4 MA MY si Za N Scholt s Anti condensation strip After installing the dishwasher open the door and stick the adhesive transparent strip under the wooden shelf in order to protect it from any condensation which may form Advice regarding the first wash cycle After the appliance has been installed immediately before running the first wash cycle completely fill the salt dispenser with water and add only then approximately 1 kg of salt see chapter entitled Rinse aid and refined sali The water may overflow this is normal and is not a cause for concern Select the water hardness value see chapter entitled Rinse aid and refined salt After the salt has been poured into the machine the LOW SALT indicator light switches off If the salt container is not filled the water softener and the heating element may be damaged as a result Technical data
32. width 59 5 cm height 82 cm depth 57 cm Capacity 14 standard place settings Water supply 0 05 1MPa 0 5 10 bar pressure 7 25 145 psi Dimensions Power supply voltage See appliance data plate Total absorbed power See appliance data plate Fuse See appliance data plate CE This dishwasher conforms to the following European Community Directives 2006 95 CE dated 16 01 2007 Low Voltage and subsequent modifications 89 336 EEC dated 03 05 89 Electromagnetic Compatibility and subsequent modifications 97 17 EC Labelling 2002 96 CE Waste Electrical and Electronic Equipment WEEE l Only available in selected models Electrical Connection Electrical Connection If your appliance is supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use Before using the appliance please read the instruction below ZN WARNING THIS APPLIANCE MUST BE EARTHED THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN Replacing the fuse When replacing a faulty fuse a 13 amp ASTA approved fuse to BS 1362 should always be used and the fuse cover re fitted If the fuse cover is lost the plug must not be used until a replacement is obtained Replacemente fuse covers If a replacement fuse cover is fitted it must be of the correct colours as indicated by the coloured marking or the colour that is embossed in words on the base of the plug Replacement
Download Pdf Manuals
Related Search