kennedy digital electronic calipers operating instructions kennedy
Contents
1. caliper is in ABS mode and displays a measurement from zero e Provided INC is not displayed in the upper left of the LCD absolute measurements may be taken e If INC is displayed hold down the ZERO ABS switch for more than two seconds the INC will dissapear and the caliper revert to absolute origin COMPARISON MEASUREMENT INC e Select the proposed zero point move the slider to that position press and release in less than a second the ZERO ABS switch e The display is now zero set and INC appears in the LCD e Measurements may now be taken from this new zero point ERROR MESSAGES ErrC or display flicker Scale surface is stained Clean the surface and coat with a thin film of low viscosity oil F in the last significant digit The slider has been moved too quickly this does not affect the measurement or the scale surface is stained see ErrC above B indication The battery voltage is low Replace the battery as soon as possible SPECIFICATIONS Resolution cccscsesesesesenenens 0 0005 0 01mm Instrumental Error 0 0 001 0 02mm Repeatability eeeee 0 0005 0 01mm Power Supply 1 x SR44 PAN 904 5020k Battery Life cgecsuaGueorsanetentsucteouesuncdetess 3 5 years Operational Temperature O C to 40 C Storage Temperature 005 10 C to 60 C SPC This caliper is fully compat2. KENNEDY DIGITAL ELECTRONIC CALIPERS 6 150mm KEN 331 1330K 6 150mm KEN 331 1710K Inside Measuring Faces Inch mm Conversion Switch 7 ORIGIN Switch ORIGIN KENNEDY ON OFF ZERO ABS Outside Measuring Power ON OFF Switch aces ZERO ABS Switch 8 200mm KEN 331 1720K 12 7300mm KEN 331 1730K Standard model without SPC Output Connector or Thumb Roller Slider Clamp Screw SPC Output Connector Except Model KEN 331 1330k Display LCD ee Be ie 1 120 130 140 150 a 5 6 KENNEDY a 3 a ae 331 171 I m a a AmA a a Tot ES INO OOP ee AA E A Ee eee eee _ gt Thumb Roller Except Model Main Scale KEN 331 1330h Depth Battery Compartment Cover Beam ecu Blade OPERATING INSTRUCTIONS FITTING THE BATTERY e Carefully remove the battery compartment cover using a coin e Install battery so that the positive side faces up e When replacing battery only use SR44 Silver Oxide cell Order Code PAN 904 5020kKk IMPORTANT After fitting replacing the battery the origin must be set as detailed below SETTING THE ORIGIN e When battery is installed replaced set the ORIGIN zero point Ensure jaws are clean close jaws and hold down the ORIGIN switch for more than a second the LCD will now show 0 00 e The ORIGIN setting feature enables the caliper to remember the position as the absolute origin ABSOLUTE MEASUREMENT ABS e With power on the
3. and coat with a thin film of low viscosity oil F in the last significant digit The slider has been moved too quickly this does not affect the measurement or the scale surface is stained see ErrC above B indication The battery voltage is low Replace the battery as soon as possible SPECIFICATIONS Resolution sescscicrciccianinevancrwncanns 0 0005 0 01mm Instrumental Error 0 001 40 02mm Repeatability cee 0 0005 0 01mm Power Supply 1 x SR44 PAN 904 5020k Battery Life ccccccececeeceeeeceeseeeneees 3 5 years Operational Temperature O C to 40 C Storage Temperature 206 10 C to 60 C SPC This caliper is fully compatible with Mitutoyo SPC equipment Except Model KEN 331 1330k Optional Accessories Connecting cable with DATA switch 1m Order Code MIT 323 3690F Connecting cable without DATA switch 2m Order Code MIT 323 3690G Data hold unit to hold displayed values Order Code MIT 323 3690A For details of SPC processing equipment please contact you distributor WARNING e Before initial use carefully remove protective oil with a soft cloth and cleaning oil e Never etch or engrave digimatic equipment this can seriously affect the accuracy of the reading and will invalidate the warranty e Damage caused by contact with machine lubricants water and other liquids will not be repa
4. attery Compartment Cover Beam T Blade OPERATING INSTRUCTIONS FITTING THE BATTERY e Carefully remove the battery compartment cover using a coin e Install battery so that the positive side faces up e When replacing battery only use SR44 Silver Oxide cell Order Code PAN 904 5020K IMPORTANT After fitting replacing the battery the origin must be set as detailed below SETTING THE ORIGIN e When battery is installed replaced set the ORIGIN zero point Ensure jaws are clean close jaws and hold down the ORIGIN switch for more than a second the LCD will now show 0 00 e The ORIGIN setting feature enables the caliper to remember the position as the absolute origin ABSOLUTE MEASUREMENT ABS e With power on the caliper is in ABS mode and displays a measurement from zero e Provided INC is not displayed in the upper left of the LCD absolute measurements may be taken e If INC is displayed hold down the ZERO ABS switch for more than two seconds the INC will dissapear and the caliper revert to absolute origin COMPARISON MEASUREMENT INC e Select the proposed zero point move the slider to that position press and release in less than a second the ZERO ABS switch e The display is now zero set and INC appears in the LCD e Measurements may now be taken from this new zero point ERROR MESSAGES ErrC or display flicker Scale surface is stained Clean the surface
5. ible with Mitutoyo SPC equipment Except Model KEN 331 1330kK Optional Accessories Connecting cable with DATA switch 1m Order Code MIT 323 3690F Connecting cable without DATA switch 2m Order Code MIT 323 3690G Data hold unit to hold displayed values Order Code MIT 323 3690A For details of SPC processing equipment please contact you distributor WARNING e Before initial use carefully remove protective oil with a soft cloth and cleaning oil e Never etch or engrave digimatic equipment this can seriously affect the accuracy of the reading and will invalidate the warranty e Damage caused by contact with machine lubricants water and other liquids will not be repaired under warranty KENNEDY DIGITAL ELECTRONIC CALIPERS 6 150mm KEN 331 1330K 6 150mm KEN 331 1710K Inside Measuring Faces Inch mm Conversion Switch T F ORIGIN Switch Y J INC opal ava fam 5 KENNEDY 0 2 HGO Pr ORIGIN Outside Measuring Power ON OFF Switch aces ey a 1 30 100 110 120 130 140 150 4 5 6 KENNEDY E pAn E EN e 331 171 NAPA BBB sees C Thumb Roller ZERO ABS Switch 8 200mm KEN 331 1720K 12 7300mm KEN 331 1730K Standard model without SPC Output Connector or Thumb Roller Slider Clamp Screw SPC Output Connector Except Model KEN 331 1330K Display LCD FRABRAE AA A F ERES A Except Model Main Scale KEN 331 1330K Depth B
6. ired under warranty
Download Pdf Manuals
Related Search