Installation and Operating Instructions
Contents
1. over 3000 hours The heater must be installed in a location that is free from vibration WARNING This appliance must be earthed Means for disconnection from the electrical supply must be incorporated in the fixed wiring in accordance with the wiring rules WARNING This heater is not equipped with a device to control room temperature Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own unless constant supervision is provided This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of expierience or knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision Children of less than 3 years should be kept away unless contiuously supervised Children aged from 3 years and less than 8 years shall only switch on off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved Children aged from 3 years and less than 8 years shall not plug in regulate and clean the appliance or perform user maintenance C2. AUTION Some parts of this product can become very hot and cause burns Particular attention has to be given where children and vunerable people are present The Dimplex QXD range is available in 1 2 and 3 lamp models with outputs of 1 5kW 3 0kW and 4 5kW respectively The three lamp models are supplied as dual voltage units SPECIFICATIONS and are suitable for use on 230 240V and 415V 3N supplies General Data Model No No of Lamps Rating Voltage Weight e v QXD1500 230 240 QXD3000 230 240 QXD4500 230 240 Material and Finished Body Casing Low carbon steel powder coated Reflectors 1080 SIA 99 8 Alum Electrochemically brightened specular finish DIMENSIONS QXD1500 1500ND 1500G d A 256 Cr 70 240 440 All dimensions in mm QXD3000 QXD4500 380 506 All dimensions in mm UNIVERSAL BRACKET MOUNTING ANGLE ADJUSTMENTS 4 FIXING HOLES 124 WIRING DIAGRAMS QXD1500 QXD3000 QXD4500 L N E L L LINKS MUST gt BE FITTED Lt Le L3 N E LINKS MUST gt BE REMOVED HEATER WIRING AS OPPOSITE CABLE ALL MODELS 2 5
3. MM SILICONE INSULATED a External connections for 230 240V 1pH b External connections for 415V 3N G Y GREEN YELLOW R RED B BLue 1 Location 2 Mounting Mounting Brackets 3 Electrical Supplies The siting of the heater s should be such as to allow an even and uninterrupted distribution of radiation to the area s to be heated Heaters are most effective when the beam angle is inclined down at an angle of 30 to 45 to the vertical IMPORTANT When deciding upon the best location consideration must be given to the following requirements a Avoid structures liable to vibration e g crane gantries which could otherwise adversely affect lamp life b The lamps are designed to operate within 5 of the horizontal plane It is very important to ensure that the heater is mounted horizontally otherwise the operating life of the lamp could be impaired c Allow a minimum of 0 5 metre clearance between the top of the heater and the ceiling Dimension C on the appliance rating label Allow a minimum of 1 5 metre clearance between the edge of heater and the adjacent wall facing that edge Dimension B on the appliance rating label d Ensure appliance is mounted the correct way up so that it can be tilted down but not up Mounting height Allow the following mounting height between the base of the heater and the floor Dimension A on the appliance rating label Model No Rating Mi
4. X lt Dimplex Models Covered QXD1500 QXD3000 and QXD4500 Installation and Operating Instructions C 08 50866 4 Issue 4 These instructions should be read carefully and retained by the user IMPORTANT SAFETY ADVICE The installation of these appliances must always be carried out by a competent electrician and be in accordance with the current wiring regulations and relevant Building Regulations The radiated heat from the heater is considerable and must be taken into account when locating the heater Ensure that the heater is not used in close proximity to the skin or eyes Always isolate the heater from the supply before undertaking any maintenance work on the appliance The QXD range of heaters are designed for internal use only They are not rated as flame proof and must not be used when flammable dusts gases or vapours etc are likely to be present in the atmosphere If in doubt advice should be sought from the Health and Safety Executive inspectors or local fire officers Quartz lamps are extremely fragile and must be handled with extreme care at all times Avoid touching the surface of the quartz sleeve with bare fingers If the sleeve is accidentally touched remove the finger print with a soft cloth moistened with methylated spirits This heater must not be located immediately above or below a fixed socket outlet or connection box The life expectancy of the halogen lamps in normal operating conditions is
5. and spread measured 1 metre above floor level which may be a more appropriate measurement for some applications HEIGHT THROW The following tables show the recommended mounting heights for three typical average intensity requirements Average QXD1500 QXD3000 QXD4500 oo Height Throw Spread Height Throw Spread Height Throw Spread ntensity onHeated F m m im mm Area W m Angled 30 from vertical Angled a omver SS Angled 45 from vertical Tangled 45 rom verea OOOO Note 1 Intensity is average intensity in W m based on Wattage of heater and area covered and measured on a horizontal plane 1m above the floor level 2 Heater mounting heights are in metres and are above floor level Those marked are minimum mounting heights for the particular heater model 3 Throw and spread figures are in metres 5 COMMISSIONING 6 MAINTENANCE 7 LAMP REPLACEMENT 1 Checks on the electrical installation should include earth continuity and insulation tests and must be undertaken by a competent person 2 Ensure that all the electrical connections at the lamps and the terminal rails have been made correctly that they are tight and that there is no loose or frayed wire 3 Replace and secure the terminal cover and replace and secure the front panel 4 Check that the mounting bracket is securely fixed in the vertical position such that the lam
6. he quartz lamp sleeve or the aluminium reflector with bare fingers If they are accidentally touched remove any finger prints using a soft cloth moistened with methylated spirit 3 Check that the lamp s are properly located in the spring retaining clips and that they have not been disturbed by cleaning The lamps should be pushed fully back into the clips for applying light pressure on the end caps only The heater is operated by simply switching on the electrical supply or if used in conjunction with a control system then the supplier s instructions must be observed ALWAYS disconnect the heater from the supply before attempting to work on or near it NEVER operate the heater with a high accumulation of dust or dirt on the lamp s or reflector or with a damaged or corroded reflector NEVER use the heater outside or in contact with water NEVER use the heater where flammable dusts gases or vapours etc are likely to be present in the atmosphere NEVER operate the heater in close proximity to the skin or eyes NEVER allow materials which could be damaged or ignited by the radiated heat to be placed in close proximity to the heater NEVER cover the heater even when it is switched off ALWAYS refer to these instructions before attempting to dismantle the heater Your Dimplex Quartz Heater is guaranteed for one year from the date of purchace We undertake to exchange or repair free of charge within this period any part found t
7. leeve with bare fingers If the sleeve is accidentally touched remove the finger print with a soft cloth moistened with methylated spirit 6 Hold the lamp firmly but gently at each end and offer up to the spring mounting clips The wire leads should face towards the front of the heater Push the lamp fully into the clips taking care to keep it square Do not twist the ends or apply undue force If either end of the lamp will not easily engage in the spring clips remove the lamp and gently ease the spring 7 The wire from each end of the lamp must be connected to the threaded connector ON THE SAME CLIP AS THE LAMP END With the outside not loosened insert the spade between the two outside nuts and tighten firmly 8 When the lamp has been fitted check that the electrical connections have been correctly made Re use the same cable tie to tether the element wires in place Re fit the front panel checking that wires are not trapped INSPECTION AND CLEANING SAFETY IN OPERATION AFTER SALES SERVICE 1 Check that all the lamps are functioning If any thermostatic or time controls are fitted ensure that the supply is on before checking lamps Any failed lamps should be replaced see lamp replacement Remove any accumulated dirt and check wiring and connections 2 Clean the lamp s and reflector s using a mild detergent solution and soft cloth Do not use any abrasive or caustic cleaners Dry with a soft cloth Avoid touching either t
8. n Height Recommended Height kW m m QXD1500 2 1 QXD3000 i 2 5 QXD4500 3 0 Note If more than one heater is to be installed ensure that the lamps of adjacent heaters are more than 3 5 metres apart Heaters are supplied with a universal bracket which may be fixed through the mounting holes to any suitable structure The bracket allows the heater to be inclined to the required angle from the vertical and permits the heater to be swivelled laterally It is recommended that when inclined from the vertical and swivelled care is taken to ensure that the lamps are still horizontal WARNING THESE HEATERS ARE DESIGNED TO BE WALL MOUNTED ONLY THEY MUST NOT BE CEILING MOUNTED THEY MUST NOT BE MOUNTED IN A ROOM CONTAINING A BATH OR SHOWER DO NOT MOUNT HEATERS CLOSER THAN 3 5 METRES FROM CURTAINS OR SIMILAR SOFT FURNISHINGS Wiring to the heater must be installed in compliance with the requirement of the wiring regulations and any local or insurance regulations All heaters are suitable for use on 230 240V single phase supplies The 4 5kW model is supplied as a dual voltage unit and is also suitable for use on 415V three phase supplies Heaters must be protected by fuses to the following rates Model No Input Rating Current Rating Fuse Rating kW EN A 230 240V_ 240V 415V 230 240V 415V QXD1500 6 25 QXD3000 3 12 5 QXD4500 18 75 6 25 Ph 10 Ph Wiring between the heater and the spur outlet or isolation switch mu
9. o be defective due to a manufacturing fault Should you require after sales service please get in touch with the supplier through whom you purchased the appliance or the contact number on your Warranty leaflet Please do not initially return a faulty appliance or part of an appliance as this may result in transit damage and or delay in providing service Let us know your difficulty quoting the model number and series letter of the appliance We will then take the appropriate action C The product complies fully with the requirements of the current EMC Directive 2004 108 EC the Low Voltage Directive 2006 95 EC and the RoHS EU Directive 2002 95 EC Dimplex A division of GDC Group Ltd Customer Services UK 0845 600 5111 Millbrook House Fax 01489 773050 Grange Drive Email customer services gdcgroup co uk Hedge End Southampton Republic of Ireland Tel 01 842 4833 Hampshire SO30 2DF c GDC Group Ltd All rights reserved Material contained in this publication may not be reproduced in whole or in part without prior permission in writing of GDC Group Limited
10. ps remain in a horizontal plane at all angles of heater displacement 5 Roughly align the heater s and tighten the adjusters 6 Switch on the heater s and check that the lamp s are all operating If time or temperature controls are fitted check these for correct and safe operation by reference to the supplier s instructions 7 Make any adjustments that are necessary to give an even spread of heat over the required area This may be done simply by perception of the heating effect or by using the distribution of visible light either at night or by darkening the room Hand over Hand over these instructions and make sure the user is familiar with all aspects of operation and safety including the need for regular cleaning and an annual inspection In the event of the premises being unoccupied then leave heater s switched off and isolated from the electrical supply Leave instructions adjacent to the electricity meter Since the Dimplex Quartz Heater contains no moving parts little maintenance is required beyond cleaning and lamp replacement It is however essential that the heater is not operated with accumulation of dust or dirt on the lamp s or reflector s as this can cause a build up of heat and eventual damage For this reason the heater must be inspected regularly depending upon conditions and at least at yearly intervals Before undertaking any maintenance work on the heater due attention must be paid to the following 1 Alway
11. s disconnect the heater from the electricity supply before attempting to work on or near it 2 Always ensure a safe means of access using an access tower or properly supported ladder 3 Some types of quartz lamps run with an internal pressure in excess of atmospheric pressure and while construction is very strong there is a slight risk of shattering If it is necessary to examine a bare lamp whilst in operation then a protective screen must be used 4 Allow adequate time for the lamps and body casing to cool before attempting to work on the heater WARNING BEFORE UNDERTAKING THIS TASK ENSURE THE HEATER IS DISCONNECTED FROM THE ELECTRICITY SUPPLY Detach heater from its mounting position 2 Unscrew the front panel by loosening the corner fixing screws and then lift front panel clear 3 Disconnect the wires to the old lamp by removing the lock nuts retaining the terminal ends adjacent to the lamp clips Do not slacken the screws as this could disturb the internal wiring 4 Remove the lamp by gently releasing the ends from the spring clips Keep the lamp secure and do not twist the ends or apply undue force IMPORTANT Release and retain the high temperature cable ties from the element wires These must not be substituted 5 Before removing the new lamp s from its protective packing it is important to be aware that quartz lamps are fragile and must be handled with care at all times Avoid touching the surface of the quartz s
12. st be in a heat resisting cable e g butyl rubber or high temperature PVC insulated Sufficient slack cable must be left to allow for angular adjustment of the heater body An all pole isolating switch with a minimum separation of 3mm in each pole must be fitted adjacent to the heater to facilitate local isolation If miniature circuit breakers are to be used to avoid nuisance tripping due to the high in rush at switch on a type 3 or C rated MCB with a tripping coefficient of 7 10 times rated current should be used Any other switching device should be Tungsten lamp load rated 4 5kW heaters must be connected in accordance with the instructions When connecting to 415V three phase supplies the links must be removed from the terminal block When using the heater on 230 240V supplies the Danger 415V notice should be removed from the terminal cover x Always ensure that the cable grip is tightened 4 Coverage for Spot Heating The area heated by a Quartz Halogen Heater depends on the height and the angle at which the heater is mounted Applications For 30 Heater Mounting Angle Area Covered Height x 2 66 Average Width of Beam Height x 2 0 Throw of Beam Height x 1 33 For 45 Heater Mounting Angle Area Covered Height x 5 72 Average Width of Beam Height x 2 2 Throw of Beam Height x 2 6 Note Area covered width and throw of beam are measured at floor level The table below indicated throw
Download Pdf Manuals
Related Search