VCC-6585P - Multicare Electronics Ltd
Contents
1. Francais Deutsch PENS ts SANYO FEATURES INSTRUCTION MANUAL VCC 6585P COLOR CCD camera About this manual Before installing and using the camera please read this manual carefully Be sure to keep it handy for later reference Depending on the conditions of use installation and environment please be sure to make the appropriate settings and adjustments If you need help with installation and or settings please consult your dealer E Backlight compensation Multi spot metering normal and high and center weighted metering E 1 3 inch CCD solid state image device E Number of total pixels 470 000 pixels E Horizontal resolution of 520 TV lines Image S N ratio of 48 dB min E Minimum required illumination of 0 5 Ix F1 2 lens E Power supply AC 24 V and DC 12 V Dimensions mm 108 1 4 20 UNC NAMES AND FUNCTIONS OF PARTS GND terminal AC24V DC12V terminal Ground terminal and power input terminal VIDEO OUT terminal BNC connector Output terminal for connecting to the video input terminal on the monitor digital video recorder or time lapse VCR POWER indicator Lights when the camera power is on Camera adjustment setting section See fe CAMERA ADJUSTMENTS SETTINGS LENS terminal Lens iris output terminal which is used to connect the lens plug2. Monitor lt 1 VIDEO OUT POWER a l A4 I I I 1 I I I I E CAMERA INSTALLATION N Camera screws Shorter ESO ai o00000 oo 20jJo ooo Digital video recorder or time lapse VCR gt gt VIDEO IN gt gt VIDEO OUT Bracket screws Longer N CONNECTIONS What you need Peripheral equipment such as monitor digital video recorder or time lapse VCR Cables for connecting peripheral equipment and camera coaxial cables connecting plugs Power adapter AC 24 V or DC 12 V Supported coaxial cables You can use any of the following coaxial cables RG 59U 3C 2V Length 250 m max RG 6U 5C 2V Length 500 m max RG 11U 7C 2V Length 600 m max fD caution When using an RG 59U 3C 2V cable do not use it on piping or air wiring Select the cable according to the distance between the devices you wish to connect If you use a cable other than the types above the image or sync signal will be attenuated and will not be transmitted correctly Making connections 1 Connect the camera and peripheral equipment 2 Connect the power cable lt When using an AC 24 V adapter gt Connect 3 wire grounded cable 18AWG or higher as shown in Figure 1 lt When using a DC 12 V adapter gt Connect the cable as shown in Figure 2 3 Insert the power adapter plug into the wall outlet The POWER indicator red lights AC 24 V connection G
3. position and focus the picture using the flange back adjustment dial Repeat steps 2 and 3 if the image does not stay in focus when changing from a wide angle shot to a telephoto shot 4 When the setting is complete tighten the LOCK screw ADJUSTMENTS AND SETTINGS CAMERA ADJUSTMENTS SETTINGS The camera comes pre adjusted and ready to install at time of factory shipment but you may want to make adjustments or settings to adapt to the operating conditions or installation environment If you have trouble adjusting the camera consult your dealer or an Authorized Sanyo Service Center Factory default setting E Iris setting Change iris setting when using either lens below for indoor use EI When using a manual or fixed iris lens and the electronic iris function is on Set the lens aperture to the shortest F stop When using an auto iris lens If the entire image is too dark or too bright adjust the contrast using the LEVEL dial e L Counterclockwise Closes the lens iris making the entire image darker H Clockwise Opens the lens iris making the entire image brighter Al NOTE on EIl setting f fluorescent lighting is used where the camera is installed the object will flicker as a result This type of phenomenon can be avoided by replacing the fluorescent lighting with incandescent lamps If the light entering the lens exceeds the maximum required illumination the image can
4. when the auto iris lens is attached Brake coil Brake coil Drive coil Drive coil LOCK screw Locking screw for the flange back adjustment dial Flange back adjustment dial Camera attachment bracket Used to attach the camera Lens mount cap Protects internal parts of the camera such as the CCD from damage Attaching the lens Use a DC type auto iris lens sold separately NOTE Do not use a lens if length L is more than 5 mm Otherwise it may damage the camera and prevent proper installation Depending on the type of lens the shape of the lens plug may differ In this case consult your dealer or an md L Authorized Sanyo Service Center L When attaching a C mount lens attach the lens to the camera after inserting the C mount ring sold separately 1 Remove the lens mount cap from the camera 2 Install the auto iris lens 3 Connect the lens plug to the LENS terminal on the side of the camera CS mount type lens PRECAUTIONS E In case of problem Do not use the unit if smoke or a strange odor comes from the unit or if it seems not to function correctly Turn off the power immediately and disconnect the power cord and then consult your dealer or an Authorized Sanyo Service Center E Do not open or modify Do not open the cabinet as it may be dangerous and cause damage to the unit For repairs consult your dealer or an Authorized Sany
5. For servicing maintenance or repairs consult your dealer or an Authorized Sanyo Service Center Scanning system PAL standard TV system 625 TV lines 25 frames s Interlace 2 1 interlace Image device Interline transfer method 1 3 inch solid state image device CCD Number of 752 H x 582 V effective pixels Sync system Internal sync Line lock only when using an AC 24 V adapter Resolution 520 TV lines horizontally 400 TV lines vertically Video output terminal 1 0 V p p 75 Q BNC composite Image S N ratio More than 48 dB More than 50 dB for AGC OFF Minimum required GAIN HI Approx 0 5 Ix F 1 2 lens illumination GAIN NORM Approx 1 0 Ix F 1 2 lens incandescent lighting Backlight OFF Multi spot metering 2 modes Center compensation weighted metering Iris function Auto iris Electronic iris Lens iris output 4 pin terminal Flange back 12 5 mm 0 5 mm White balance Auto tracing white balance Manual Gain control Normal High Lens mount CS mount Operating Temperature 10 C 50 C 14 F 122 F environment Humidity less than 90 RH no condensation Power supply AC 24 V 410 50 Hz DC 12 15 V Power consumption 3 6 W with auto iris lens Weight Approx 280 g without lens Appearance and specifications are subject to change without prior notice or obligations CONNECTIONS AND INSTALLATION EX CONNECTIONS
6. ND AC24V DC 12 V connection oo ale Ss lala ole DC12V 2 To prevent a fire hazard use any UL listed wire rated VW 1 for the AC 24 V input terminal Check that the polarity is correct Figure 2 3 A Bc HI CENT i Al PHASE LEVEL NORM OFF ATW tL E CAMERA INSTALLATION Camera attachment bracket The camera attachment bracket can be reconfigured as shown in Figure E CAMERA INSTALLATION above depending on the installation environment As per design use the removed screws NOTE When monitoring lighting or other extremely bright objects which exceed the maximum required illumination smearing may occur in the vertical or horizontal direction either above and below the high brightness object or as a perpendicular band In such a case adjust the angle of illumination and other factors while observing the monitor When using the camera attachment stand sold separately select a location that will be able to withstand the weight of the camera and stand for many years and fix them securely in place Flange back adjustment This normally does not need adjustment If the picture is out of focus at the telephoto position adjust the flange back position as described below 1 Loosen the LOCK screw 2 Set to the maximum telephoto position and focus the picture using the focus ring 3 Set to the maximum wide angle
7. not be displayed properly In that case manually adjust the lens iris AA Gain control For adjusting the sensitivity of the camera Use this setting for shooting in dark environments HI Increased sensitivity allows shots to be taken in dark environments NORM Normal setting NOTE The HI setting causes noise generation and a grainy image Ei BLC Backlight compensation This camera has three different backlight compensation modes Change the mode to match the backlight condition Multi spot metering normal mode 3 When applying backlight compensation E m to the entire screen Multi spot metering high mode 3 When applying more backlight compensation than normal mode 2 Center weighted metering mode When applying backlight compensation to only the central portion of the screen OFF This function is off m m NOTE on multi spot metering If the background of the object is extremely dark set to Center weighted metering mode El WB White balance color compensation Lets you fine tune the white balance manually MANU wa R Red dial Turn clockwise to augment screen red B Blue dial Turn clockwise to augment screen blue ATW Compensation is performed automatically H Sync setting Only when using an AC 24 V adapter Line Lock Synchronizes the unit with power frequency when two or m
8. o Service Center E Do not put objects inside the unit Make sure that no metal objects or flammable substance get inside the unit If used with a foreign object inside it could cause a fire a short circuit or damage Be careful to protect the unit from rain sea water etc If water or liquid gets inside the unit turn off the power immediately and disconnect the power cord and then consult your dealer or an Authorized Sanyo Service Center E Be careful when handling the unit To prevent damage do not drop the unit or subject it to strong shock or vibration E Do not install this unit close to magnetic fields The magnetic fields may result in unstable operation E Protect from humidity and dust To prevent damage do not install the unit where there is greasy smoke or steam where the humidity may get too high or where there is a lot of dust E Protect from high temperatures Do not install close to stoves or other heat sources such as spotlights etc or where it could be subject to direct sunlight as this could cause deformation discoloration or other damages Be careful when installing close to the ceiling in a kitchen or boiler room as the temperature may rise to high levels E Cleaning Dirt can be removed from the cabinet by wiping it with a soft cloth To remove stains wipe with a soft cloth moistened with a soft detergent solution and wrung dry then dry by wiping with a soft cloth Do not use benzine thinne
9. ore cameras are connected via a switcher unit When the image on the monitor rolls vertically adjust the phase If using this unit as the second or subsequent camera LL Adjust the roll by turning the PHASE dial e If using this unit as the first camera Adjust the roll using the phase adjuster on the second and subsequent cameras INT Internal sync NOTE When using a DC 12 V adapter the sync setting is set to Internal sync
10. r or other chemical products on the cabinet as this may cause deformation and paint peeling Before using a chemical cloth make sure to read all accompanying instructions Make sure that no plastic or rubber material comes into contact with the cabinet for a long period of time as this may cause damage or paint peeling Printed on recycled paper SANYO SANYO Electric Co Ltd Printed in Japan 1AC6P1P2814 L5AX2 XE 0704TR SY TROUBLESHOOTING SPECIFICATIONS Before sending the camera out for repair check the items below If the problem persists after checking these items consult your dealer or an Authorized Sanyo Service Center E If no image appears Is the coaxial cable attached securely Are the power and voltage normal Has the iris of the lens been adjusted correctly with the LEVEL dial Is there adequate illumination E If the image is unclear Is the monitor adjusted correctly Is the flange back position correctly set Is the lens in focus Is the lens clean Dirt or fingerprints on the lens can adversely affect the image Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid commercially available SERVICE The camera is a precision instrument Handle it carefully and always follow the safety precautions If the camera requires service never try to repair it yourself or open the casing
Download Pdf Manuals
Related Search