Hormann FCT10 Fitting Instructions
Contents
1. Anleitung f r Montage und Betrieb Funkcodetaster FCT 10 Installation and operating instructions FCT 10 Code Modulator Notice de montage et d installation Clavier de codage FCT 10 Handleiding voor montage en bediening Telecoderingsschakelaar FCT 10 Istruzioni per il montaggio e l uso Tastiera a radiocodice FCT 10 Instrucciones de montaje y de servicio Pulsador codificado FCT 10 Bruksanvisning f r montering och drift Kodi s FCT 10 Instrukcja monta u i u ytkowania Kodowy sterownik radiowy FCT 10 Szer l si s m k dtet si tmutat FCT 10 k dkapcsol Deutseh E 4 English 18 Fran ais we 31 Nederlands 45 Italiano a 58 ESDANOL EE eebe 72 Ve a AE AT 86 de EA RE AE ER EER PE EG 98 Ee Ve 112 EN 50081 C EN 50082 I ETS 300220 09 2006 TR20A002 A RE 3 ENGLISH DON 5 1 1 5 1 2 5 1 3 5 2 5 2 1 5 2 2 5 2 3 5 3 5 3 1 5 3 2 5 3 3 1 General Installation Important terminology Putting into operation Changing the battery Normal Operation Programming Functions Altering the IB code or entering a personal IB code Entering or altering the access codes Deleting the access codes Operating functions Transmitting after entering an access code Learning after entering an access code Recoding a radio code location with an access code or resetting this radio code location to the factory coding Direct function of the bell light key Transmitting using the2. bell light key Learning using the bell light key Recoding the radio code location of the bell light key or resetting this radio code location to the factory coding EU Manufacturer s Declaration General The FCT 10 Code Modulator is a combination of a hand transmitter and a digital coder and apart from the receivers which for the main part are already available does not require any additional equipment 18 09 2006 TR20A002 A RE The FCT 10 is powered by a proprietary 9V block battery Successful entries and alterations are stored and retained even in the event of a voltage loss With ten freely selectable 2 to 6 digit access codes just as many functions can be activated by radio signal Le with an FCT 10 it is possible to actuate by radio signal and impulse for example up to ten door operators In addition a direct function not protected by an access code is available with which for example and also by radio signal together with a correspon ding receiver a bell or outdoor lighting can be operated 2 Installation see figure 1 3 Important terminology Start up code IB code This is an 8 digit number code which is required in order to protect the unit against unauthorized programming theft protection Only using this 8 digit number code can the access codes be entered altered or deleted In addition entry of this code is also required after inserting the battery e g when starting up or on changing the ba
3. adio code can be repeatedly transmitted without a new access code having to be entered as in doing so the bell light key for prematurely terminating this phase is re quired During these 20 seconds the direct function of the bell light key is therefore deactivated 5 3 1 Transmitting using the bell light key 1 Press the bell light key 2 a long signal tone sounds and the radio code belonging to it is transmitted in doing so rapid signal tones sound 09 2006 TR20A002 A RE 27 5 3 2 Learning using the bell light key de Hold the teaching transmitter as shown to the FCT 10 and then press and keep pressed the desired key of which the radio code is to be learned see figure 5 2 Press the bell ight key and keep it pressed if a valid entry has been made a long signal tone sounds 3 If the received signal from the teaching transmitter is strong enough after approx 0 5 seconds brief signal tones are emitted for about 4 seconds indicating that the signal can be learned 4 Keep the keys pressed right up until the end of these 4 seconds after successfully entering the access code a long signal tone sounds 5 Release the keys of the teaching transmitter and of the FCT 10 6 Carry out a function test if this is unsuccessful repeat the operation 5 3 3 Recoding the radio code location of the bell light key or resetting this radio code location to the factory coding 1 Press the bell light key and ke
4. andards ETS 300 683 issue 06 97 ETS 300 220 issue 10 93 EN 300 220 1 issue 11 97 Steinhagen 01 01 2001 ppa Axel Becker Management 30 09 2006 TR20A002 A RE N N N N IS K N N N N N N N N N N IS N N N IS N N N 125 09 2006 TR20A002 A RE 127 09 2006 TR20A002 A RE 09 2006 TR20A002 A RE 128 N I co 433 MHz 129 09 2006 TR20A002 A RE
5. ccess codes are either empty or deleted so that no enterable code matches them The access codes can be entered or altered as follows Figure 3 1 Press the key switch 2 Enter the valid 8 digit IB code using the numeric keys 3 Press the key switch if a valid entry has been made a long signal tone sounds 22 09 2006 TR20A002 A RE A Enter the single digit storage space number using a numeric key 5 Press the key switch 3 if a valid entry has been made a long signal sounds 6 Enter the desired 2 6 digit access code using the numeric keys 7 Press the key switch if a valid entry has been made a long signal tone sounds and the entered or altered access code is valid with immediate effect 5 1 3 Deleting the access codes Each of the ten storage spaces for the access codes numbered O to 9 can be deleted so that no enterable code matches them Figure 4 1 Press the key switch 2 Enter the valid 8 digit IB code using the numeric keys 3 Press the key switch A if a valid entry has been made a long signal tone sounds 4 Enter the single digit storage space number using a numeric key 5 Press the key switch if a valid entry has been made a long signal sounds 6 Press the key switch again a long signal tone sounds and the access code of the storage space in question is deleted 09 2006 TR20A002 A RE 23 5 2 Operating functions The operating functions are the func
6. connection it is assumed that any possible phases from the operating functions have expired This is always signalled by a long signal tone If there is any doubt about this before making an entry you should wait more than 20 seconds without pressing any key 09 2006 TR20A002 A RE 91 5 1 1 Altering the IB code or entering a personal IB code After the unit is initially put into operation or after the factory reset it is essential that you change the factory presetting of the IB code 12345678 to a personal 8 digit IB code Figure 2 It is essential that you take note of this changed IB code because if you lose it the unit can only be made to work again after a so Called factory reset carried out at the factory 1 Press the key switch 2 Enter the current 8 digit IB code using the numeric keys 3 Press the key switch if a valid entry has been made a long signal tone sounds 4 Enter the new 8 digit IB code using the numeric keys 5 Press the key switch f a valid entry has been made a long signal tone sounds 6 Enter the new IB code 6 digit again using the numeric keys 7 Press the key switch if a valid entry has been made a long signal tone sounds and the new IB code is valid with immediate effect 8 You can make a note of the IB code here gt 5 1 2 Entering or altering the access codes In the ex factory state or after the factory reset all ten storage spaces numbered from O to 9 for the a
7. ep it pressed gt a long signal tone sounds 2 Immediately afterwards press the key switch in addition and keep it pressed brief signal tones start to be emitted for approx 4 seconds indicating that it is possible to recode or to reset to the factory coding 28 09 2006 TR20A002 A RE Ifone of the two keys is released before the end ofthese 4 seconds the existing radio code is then overwritten by a new unique radio code after successfully recoding a long signal tone sounds Ifthe two keys continue to be pressed right up until the end of the 4 seconds the existing radio code is reset to the factory coding 3 after successfully resetting to the factory setting a long signal tone sounds 3 Release the keys 6 EU Manufacturer s Declaration Manufacturer Verkaufsgesellschaft KG Upheider Weg 94 98 D 33803 Steinhagen Product Code modulator Unit type FCT 10 On the basis of its design and type in the version marketed by us the product described above meets the relevant basic requirements of the directives lis ted below In the event that the product is changed or modified without our approval this declaration loses its validity 09 2006 TR20A002 A RE 29 Relevant Directives that the product complies with Conformity of the above mentioned products with the requirements of the Directives according to Section 3 of the R 4 TTE Directives 1995 5 EC has been proven by observance of the following Standards Applied St
8. id access code using the numeric keys Press the key switch and keep it pressed gt if a valid entry has been made a long signal tone sounds Immediately afterwards press the bell light key in addition and keep it pressed A brief signal tones start to be issued for approx 4 seconds indicating that the unit can be recoded or reset to the factory coding Ifone of the two keys is released before the end of these 4 seconds the existing radio code is overwritten by a new unique radio code 3 after successfully recoding a long signal tone sounds Ifthe two keys continue to be pressed until the end ofthe 4 seconds the existing radio code is reset to the factory coding 2 after successfully resetting to the factory code a long signal tone sounds Release the keys 09 2006 TR20A002 A RE 5 3 Direct function of the bell light key During normal operation the bell light key has a special status it can be used directly just like a hand transmitter for transmitting and learning i e without having to enter an access code Furthermore its radio code can be recoded as well as reset to the factory coding Within the operating functions this direct function is nearly always active i e even when an access code is being entered provided no other key is being pressed or in another radio code location no transmission learning re coding or factory coding is taking place An exception is the phase of 20 seconds in which the same r
9. reassigned to all the radio code locations 4 Putting into operation Changing the battery If the unit is not connected to a battery for longer than 5 10 minutes or if the connected battery is fully run down and a new one has to be inserted then the FCT 10 is in the so called start up mode This is signalled by a brief signal tone every 4 seconds In this connection all normal functions are deactivated In order to activate these functions the valid start up code for the unit IB code in the ex factory state or after the factory reset always 12345678 must be entered 1 Connect the battery a signal tone sounds every 4 seconds 2 Enter the valid 8 digit IB code using the numeric keys every time a numeric key is pressed this is acknowledged by a brief signal tone 3 Press the key switch 3 when a valid entry has been made a long signal tone sounds indicating that the unit is now in the normal operating mode 20 09 2006 TR20A002 A RE 5 Normal operation During normal operation all the normal functions of the unit are activated whereby a distinction is made between the programming functions and the operating functions 5 1 Programming functions Referred to here are the functions with which the operating functions can be preset programmed The programming functions essentially differ from the operating functions to the extent that before the actual numeric entry is made the key switch is pressed In this
10. tions which after putting the unit into opera tion and entering the access codes represent the actual operation of the unit 5 2 1 Transmitting after entering an access code 1 Enter the valid access code using the numeric keys 2 Press the key switch 3 if a valid entry has been made a long signal tone sounds and the corresponding radio code is transmitted in doing so rapid signal tones sound 24 09 2006 TR20A002 A RE 5 2 2 Learning after entering an access code Enter the valid access code using the numeric keys Hold the teaching transmitter as shown to the FCT 10 and then press and keep pressed the desired key of which the radio code is to be learned see figure 5 Press the key switch and keep it pressed f a valid entry has been made a long signal tone sounds 1 2 09 2006 TR20A002 A RE 25 4 If the received signal from the teaching transmitter is strong enough after approx 0 5 seconds brief signal tones are emitted for about 4 seconds indicating that the signal can be learned Keep the keys pressed right up until the end of these 4 seconds after successfully entering the access code a long signal tone sounds Release the keys of the teaching transmitter and the FCT 10 Carry out a function test if this is unsuccessful repeat the operation 5 2 3 Recoding a radio code location with an access code or 26 resetting this radio code location to the factory coding Enter the val
11. ttery in order to activate the unit s functions theft protection In the ex factory state this code is preset with 12345678 The user should replace this preset code with his own personal IB code to ensure that no one else can gain access to the programming and hence the functions of the unit If the personal IB code gets lost then the unit can only be made to work again by undergoing a so called factory reset in the factory after which the unit is returned to the ex factory state 09 2006 TR20A002 A RE 19 Access codes These are 2 to 6 digit freely selectable number codes with which access can be gained to the ten radio code locations numbered from 0 to 9 whereby an access code is always assigned a specific radio code location In the ex factory state or after the factory reset the storage spaces for the access codes are either empty or deleted so that no enterable code matches them Radio code location This is a location for a radio code which as with the hand transmitters can be transmitted learned or recoded and reset to the factory coding In addition to the ten radio code locations numbered from O to 9 which can be accessed using the access codes there is a further radio code location which can be directly accessed without using an access code This is why there are a total of 11 radio code locations in the unit Radio code The 1 billion security code which in the ex factory state or after the factory reset is uniquely p
Download Pdf Manuals
Related Search